Texas Instruments

LM393N/NOPB - Dual Open-Collector Comparator | Texas Instruments

MPN: LM393N/NOPB ✓ نشط
2.0 mV maximum Vdss PDIP-8 Package
الحد الأدنى للطلب: 1 |

LM393N/NOPB نظرة عامة

The Texas Instruments LM393N/NOPB is a low-power, low-offset-voltage dual comparator with two independent comparison channels, open-collector outputs, and an 8-pin PDIP package. The device supports single-supply operation, features an input offset voltage specification as low as 2.0 mV maximum, and is rated for an operating temperature range of 0°C to +70°C.

A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state at its output. The LM393-N belongs to the dual-comparator hierarchy within the broader comparator and amplifier IC category. Its two channels are electrically independent, allowing one device to implement two threshold decisions. Open-collector outputs add flexibility because an external pull-up resistor can establish the output voltage and enable wired logic or interface with higher-voltage systems.

The principal benefits are low power consumption, a low input offset voltage, single-supply operation, and independent dual-channel operation. The 2.0 mV maximum offset specification is particularly useful when the difference between two sensed voltages is small. Each open-collector output can sink conventional logic current while remaining released when the comparison state is inactive. Because the outputs are not push-pull, each channel requires an external pull-up resistor for normal high-state operation.

The two comparators can operate from a single supply or from split supplies, which supports both grounded sensing systems and bipolar input arrangements. Each channel accepts non-inverting and inverting inputs, giving designers freedom to choose the signal on each side of the threshold. The output polarity is determined by the input relationship: the non-inverting input above the inverting input produces the asserted transistor state, subject to the external pull-up network and the device's output timing behavior.

Typical applications include sensor threshold detection, battery and power-supply monitoring, window comparators, overvoltage and undervoltage protection, industrial control interfaces, and logic-level translation. The independent channels also suit applications where two unrelated measurements must be converted into logic states, such as temperature-limit detection combined with a supply-rail fault signal.

For PCB design, place pull-up resistors close to the open-collector pins and route comparator inputs away from switching nodes and high-current return paths. Input bias currents can create voltage errors with high source impedance, so resistive dividers should have appropriately low source impedance. Confirm the input common-mode range, supply limits, output sink-current capability, and timing requirements against the manufacturer datasheet before finalizing the circuit.

This page combines manufacturer specifications, sourcing information, pin-to-pin alternatives, comparison criteria, and practical circuit guidance to support faster component selection and PCB implementation. The LM393N/NOPB remains especially useful where two independent low-power comparator channels and a through-hole 8-pin footprint are required.

بدائل مباشرة لـ LM393N/NOPB — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع LM393N/NOPB (نفس عامل الشكل والبصمة) — يختلف في Comparator Type, Operating Temperature Range, Package, Mounting Type, Number of Comparators.

Texas Instruments
Comparator Type: Dual differential voltage comparator
Operating Temperature Range: 0 °C to 70 °C
Package: 8-pin SOIC (D), 3.90 mm width
Texas Instruments
Comparator Type: Dual General-Purpose Comparator
Operating Temperature Range: 0 C to +70 C (LM393N) / -40 C to +85 C (LM2903N)
Package: 8-PDIP (DIP-8, through-hole)

LM393N

✅ بديل مباشر
Texas Instruments
📦 8-pin DIP
Dual General-Purpose Comparator · 2 (dual) · Open-Collector / Open-Drain (single-ended) · 5 mV (LM393N); 2 mV (LM193/LM393A grade) · 25 nA · 2 V to 36 V · ±1 V to ±18 V · 16 mA

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM393N

✅ بديل مباشر
Texas Instruments
📦 8-pin DIP
Dual General-Purpose Comparator · 2 (dual) · Open-Collector / Open-Drain (single-ended) · 5 mV (LM393N); 2 mV (LM193/LM393A grade) · 25 nA · 2 V to 36 V · ±1 V to ±18 V · 16 mA

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM393N

✅ بديل مباشر
Texas Instruments
📦 8-pin DIP
Dual General-Purpose Comparator · 2 (dual) · Open-Collector / Open-Drain (single-ended) · 5 mV (LM393N); 2 mV (LM193/LM393A grade) · 25 nA · 2 V to 36 V · ±1 V to ±18 V · 16 mA

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM393N/NOPB الحدود القصوى والخصائص الكهربائية

Comparator Type General-purpose dual comparator
Number of Comparators 2
Number of Independent Channels 2
Input Offset Voltage 2.0 mV maximum
Supply Configuration Single supply or split supply
نوع الخرج Open-collector
العلبة PDIP-8
عدد الأطراف 8 pins
نطاق درجة حرارة التشغيل 0°C to +70°C
نوع التركيب Through-hole

دليل تكوين أطراف LM393N/NOPB pdip-8

تكوين الأطراف لـ LM393N/NOPB (حزمة pdip-8). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة pdip-8 لـ LM393N/NOPB

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM393N/NOPB.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

LM393N/NOPB مناسب لـ 6 التطبيقs: Battery Voltage Threshold Detection, Industrial Sensor Limit Switching, Power-Supply Overvoltage Protection, Window Comparator Control, Motor and Relay Threshold Interface, Logic-Level and System Interfacing.

⚡

Battery Voltage Threshold Detection

The LM393N/NOPB fits battery monitoring because it combines two independent comparator channels, a 2.0 mV maximum input offset specification, and single-supply operation in one 8-pin PDIP package. One channel can compare a divided battery voltage with a reference to detect an overvoltage condition, while the other can monitor the opposite threshold. Each open-collector output can drive a pull-up and status LED or digital input. The design benefit is low component count, although input bias current can create errors with high-impedance dividers and the battery operating range must remain within the device's published supply and common-mode limits.

🏭

Industrial Sensor Limit Switching

The LM393N/NOPB is useful for industrial sensor interfaces that convert an analog level into a logic decision. Its two independent channels can monitor two sensor-derived voltages, such as a temperature threshold and a pressure threshold, without sharing internal signal paths. The 2.0 mV maximum offset specification helps preserve small transition margins, while the open-collector outputs allow pull-ups to the system's logic supply. Layout should keep input traces away from motors, relays, and switching power nodes, and the external reference network should have low enough impedance to minimize bias-current error.

🔧

Power-Supply Overvoltage Protection

LM393N/NOPB can supervise a power rail by comparing a scaled supply voltage against a stable reference and asserting an open-collector fault output when the monitored rail crosses a limit. Its two independent channels permit separate upper- and lower-bound supervision when both thresholds are required. The 8-pin PDIP format is particularly convenient for through-hole industrial boards, and open-collector outputs can be pulled up to the fault-system logic rail. The implementation must verify the input common-mode range at both extremes, account for resistor-divider tolerance, and ensure the pull-up voltage remains acceptable to every connected device.

📺

Window Comparator Control

The two independent LM393N/NOPB channels can form a window comparator when one input of each channel receives a lower reference and the other receives an upper reference. The output state indicates whether the measured signal lies inside the permitted band. This arrangement benefits from the device's 2.0 mV maximum offset specification and low-power operation, while the open-collector outputs can be pulled up separately or combined through wired logic. Resistor matching and reference accuracy will often determine practical boundary accuracy, so use the resistor network and input bias current from the manufacturer datasheet to calculate worst-case threshold error.

⚡

Motor and Relay Threshold Interface

The LM393N/NOPB can convert motor-current, temperature, or position-sensor levels into control signals for relay and driver logic. Two channels allow a start/stop threshold pair to be evaluated independently, and the open-collector interface can operate at a pull-up voltage selected for the receiving logic. The through-hole PDIP package supports repairable industrial-control layouts. Because motor environments contain switching transients, comparator inputs and reference nodes should be physically separated from inductive and high-current paths, and suitable filtering should be designed without degrading the required response time.

🖥️

Logic-Level and System Interfacing

LM393N/NOPB can bridge a low-voltage analog decision to a digital subsystem because its open-collector output can be pulled up to the voltage required by the receiving logic. A single device provides two independent channels for interlock, direction, or status signals. The architecture avoids the need for a dedicated push-pull line driver when wired logic is acceptable, although every pull-up must preserve valid input levels for the connected device. Confirm output sink-current capability, logic thresholds, response timing, and common-mode limits before using the part as a general-purpose logic translator.

What are the key specifications of LM393N/NOPB that engineers should know?
The LM393N/NOPB is a dual, independent, general-purpose comparator with open-collector outputs and an input offset voltage specification as low as 2.0 mV maximum. According to the Texas Instruments LM393-N product page, the device is offered in an 8-pin PDIP package and is specified from 0°C to +70°C. Each channel can operate from a single supply, while an external pull-up resistor is required to convert the open-collector output into a logic-high state.
Where can I download the LM393N/NOPB datasheet PDF?
The LM393N/NOPB datasheet is available through the Texas Instruments LM393-N product page at https://www.ti.com/product/LM393-N. The manufacturer identifies the device as a low-power, low-offset-voltage dual comparator and provides ordering information for LM393N/NOPB. Use the datasheet's pin-description table, electrical-characteristics table, and application guidance before finalizing the PCB and selecting pull-up resistor values.
Where can I find the LM393N pinout?
The LM393N pinout is documented in the Texas Instruments LM393-N datasheet and product-page package information. The LM393N/NOPB uses an 8-pin PDIP package with two comparator channels and open-collector outputs. Because the verified product information does not reproduce every terminal name, use the manufacturer pin-description diagram when assigning PCB tracks, especially to distinguish each channel's two inputs, output, and power terminals.
Is LM393N/NOPB the same as LM393N?
LM393N and LM393N/NOPB refer to closely related orderable forms in the Texas Instruments LM393-N family, but the suffix must be checked against the manufacturer ordering table before substitution. Both identify the same underlying dual-comparator device family, yet packaging codes, lead finishes, and procurement requirements can differ. For an exact PCB and purchasing decision, approve the complete orderable MPN rather than treating a shortened base number as automatically interchangeable.
What is LM393N equivalent to?
The closest documented equivalents to LM393N/NOPB are dual open-collector comparators in an 8-pin DIP package, including LM393N from onsemi and STMicroelectronics. The available cross-reference material identifies these as functionally comparable replacements, but it does not establish identical offset voltage, supply limits, common-mode range, and timing across every manufacturer. Confirm those electrical limits in each candidate's datasheet before approving a drop-in replacement.
What can replace LM393N/NOPB?
An LM393N from onsemi, STMicroelectronics, or Rochester Electronics is a candidate replacement for LM393N/NOPB because the documented parts are dual general-purpose comparators associated with an 8-pin DIP footprint. The replacement must preserve the open-collector output architecture, supply voltage, common-mode range, input offset behavior, and output-current requirements. Do not substitute a push-pull-output comparator without redesigning the output interface.
Is LM393N/NOPB suitable for battery monitoring?
Yes, LM393N/NOPB is suitable for many battery-threshold monitoring circuits because it provides two independent low-power comparison channels and supports single-supply operation. The input offset specification as low as 2.0 mV can help preserve small voltage margins. The actual battery chemistry, cell range, threshold accuracy, quiescent current, and operating temperature must still be checked against the complete electrical specifications in the manufacturer datasheet.
How is an open-collector LM393N output connected?
Each LM393N open-collector output requires an external pull-up resistor to a suitable positive supply. The internal transistor sinks current when the comparator asserts its output, while the resistor creates the high voltage when the transistor turns off. The same architecture can support wired logic if the electrical interface permits it. Select the resistor to balance rise time, power consumption, sink-current capability, and the voltage presented to the next circuit.
LM393N/NOPB vs LM393N from onsemi — which is better for a new design?
Choose the Texas Instruments LM393N/NOPB when its exact ordering, temperature range, and procurement requirements fit the design. Choose the onsemi LM393N when that manufacturer's electrical limits provide a better fit or the required sourcing route is available. Both are documented as 8-pin general-purpose DIP comparators, but the available cross-reference material does not prove equal offset voltage, timing, supply range, or output-current performance, so those parameters decide the choice.
When should I choose LM393N/NOPB over another dual comparator?
Choose LM393N/NOPB when a through-hole design needs two independent low-power comparison channels, open-collector outputs, single-supply operation, and a low offset specification. Prefer another dual comparator when it offers rail-to-rail input operation, faster response, lower supply current, push-pull outputs, or a package smaller than PDIP-8. Its strongest fit is legacy-style or industrial control boards where the established 8-pin footprint and flexible pull-up interface are valuable.
What is the operating temperature range of LM393N/NOPB?
The LM393N/NOPB is specified for an operating temperature range of 0°C to +70°C. According to the Texas Instruments ordering information, the device is packaged in an 8-pin PDIP form. If the application must operate below 0°C or above +70°C, select a comparator with a wider temperature grade rather than extrapolating beyond the published operating range.
Why does the LM393N/NOPB need pull-up resistors?
The LM393N/NOPB uses open-collector outputs, so the internal output transistors can pull the output low but cannot actively drive it high. A pull-up resistor provides the high-state voltage and limits current through the output transistor during the low state. Each of the two outputs needs its own pull-up arrangement unless the circuit deliberately uses a shared wired-logic bus.
Can LM393N/NOPB operate from split supplies?
Yes. The Texas Instruments LM393-N family is designed for single-supply or split-supply operation. Split supplies can place the input and output reference near ground while permitting a bipolar input range. Verify the exact common-mode and supply limits for LM393N/NOPB in the manufacturer datasheet, because the permissible input range can be narrower than the total supply span.
Where can I buy LM393N/NOPB online?
Use the Request a Quote form on this page to request LM393N/NOPB pricing, stock confirmation, and lead time. The form connects the request with XAIPART's sales process and is the appropriate channel for an exact 8-pin PDIP order. Quote requests should identify the complete MPN, required quantity, and whether additional sourcing documentation is needed.
How much does LM393N/NOPB cost and what is its lead time?
The current unit price and lead time for LM393N/NOPB should be confirmed through the Request a Quote form on this page. Dynamic commercial terms can change with quantity, inventory, packaging requirements, and market conditions, so request a current quotation rather than relying on an archived amount. Include the desired quantity and target delivery date to obtain an actionable response.
Is LM393N/NOPB in stock?
Stock for LM393N/NOPB should be confirmed through the Request a Quote form on this page with the required quantity stated. The part's lifecycle classification and availability can differ by warehouse and order quantity, and an exact MPN check is necessary to avoid confusion with related LM393 family order codes. The quote team can confirm current stock and the expected lead time for the requested quantity.

بيانات مرجعية هندسية لـ LM393N/NOPB — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose LM393N/NOPB for a through-hole design that requires two independent low-power comparator channels, open-collector outputs, and single- or split-supply operation. It is especially appropriate when the 2.0 mV maximum input offset specification is relevant and the 8-pin PDIP footprint is already established on the PCB. Choose the onsemi LM393N when that manufacturer's detailed limits or sourcing fit the project better, or the STMicroelectronics LM393N when its electrical characteristics provide a better match. Treat the Rochester Electronics LM393N as another DIP-format candidate, but verify lifecycle, exact pinout, electrical limits, and output architecture before approval. None of the alternatives should be selected solely from the family name: check supply range, common-mode range, offset voltage, response time, output sink current, temperature grade, and open-collector behavior. A modern push-pull or rail-to-rail comparator may be preferable in a new surface-mount design, but it is not a direct drop-in substitute without footprint and output-interface review.

المقارنة مع البدائل

المعامل هذا المنتج LM393N LM393N LM393N
Brand Texas Instruments onsemi STMicroelectronics Rochester Electronics
Package 8-pin PDIP 8-pin DIP 8-pin DIP 8-pin DIP
Comparator Configuration Dual, independent comparator Dual comparator Dual comparator Dual comparator
Mounting Type Through-hole Through-hole Through-hole Through-hole
Number of Pins 8 pins 8 pins 8 pins 8 pins

أبرز الفروقات

  • Two independent channels in one through-hole package (مقابلLM393N from STMicroelectronics)
  • Documented low input offset specification (مقابلLM393N from onsemi)
  • Flexible open-collector output interface (مقابلLM393N from Rochester Electronics)

ملاحظات التصميم

Assign the PCB footprint from the manufacturer pin-description diagram rather than relying on the generic DIP outline. Keep each comparator's two input traces short and pair them away from switching nodes, relay coils, motor traces, and high-current return paths. Place the pull-up resistor associated with each open-collector output close to that output pin. For sensitive threshold measurements, use a quiet ground reference and avoid sharing narrow ground paths between the comparator and switching circuitry.

Do not treat the open-collector output as a push-pull logic output. Each low output must conduct current through a pull-up resistor, and the resistor voltage, power dissipation, and resulting rise time must be checked against the receiver's input requirements. Also verify that the sensed voltage remains inside the comparator's common-mode range. A supply voltage that is sufficient for operation does not automatically make every input voltage valid.

Account for input bias current when designing high-impedance resistor dividers. The bias current flowing through divider resistance produces an offset that can be comparable to the LM393N/NOPB's 2.0 mV maximum input offset specification. Use lower divider impedance when the source can drive it, or buffer the divider with a suitable low-input-bias amplifier when the sensor requires a high-impedance input.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The verified product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this general-purpose commercial comparator ordering.

تم التحقق من البيانات في: 2026-11-17 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

lm393n nopb lm393n nopb datasheet lm393n datasheet lm393n pinout lm393n equivalent lm393n datasheet pdf lm393n circuit lm393n pdf lm393n dip 8 LM393N/NOPB price LM393N/NOPB replacement Texas Instruments LM393N/NOPB

المكونات والمصطلحات ذات الصلة

Texas Instruments LM393N/NOPB LM393-N LM393N onsemi STMicroelectronics Rochester Electronics dual comparator comparator analog integrated circuit amplifier IC semiconductor open-collector output input offset voltage common-mode voltage range single-supply operation split-supply operation PDIP-8 DIP package through-hole package pull-up resistor battery monitoring industrial sensor interface window comparator power-supply supervision
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر