LM393N/NOPB - Dual Open-Collector Comparator | Texas Instruments
N.º de pieza: LM393N/NOPB ✓ ActivoLM393N/NOPB Descripción general
A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state at its output. The LM393-N belongs to the dual-comparator hierarchy within the broader comparator and amplifier IC category. Its two channels are electrically independent, allowing one device to implement two threshold decisions. Open-collector outputs add flexibility because an external pull-up resistor can establish the output voltage and enable wired logic or interface with higher-voltage systems.
The principal benefits are low power consumption, a low input offset voltage, single-supply operation, and independent dual-channel operation. The 2.0 mV maximum offset specification is particularly useful when the difference between two sensed voltages is small. Each open-collector output can sink conventional logic current while remaining released when the comparison state is inactive. Because the outputs are not push-pull, each channel requires an external pull-up resistor for normal high-state operation.
The two comparators can operate from a single supply or from split supplies, which supports both grounded sensing systems and bipolar input arrangements. Each channel accepts non-inverting and inverting inputs, giving designers freedom to choose the signal on each side of the threshold. The output polarity is determined by the input relationship: the non-inverting input above the inverting input produces the asserted transistor state, subject to the external pull-up network and the device's output timing behavior.
Typical applications include sensor threshold detection, battery and power-supply monitoring, window comparators, overvoltage and undervoltage protection, industrial control interfaces, and logic-level translation. The independent channels also suit applications where two unrelated measurements must be converted into logic states, such as temperature-limit detection combined with a supply-rail fault signal.
For PCB design, place pull-up resistors close to the open-collector pins and route comparator inputs away from switching nodes and high-current return paths. Input bias currents can create voltage errors with high source impedance, so resistive dividers should have appropriately low source impedance. Confirm the input common-mode range, supply limits, output sink-current capability, and timing requirements against the manufacturer datasheet before finalizing the circuit.
This page combines manufacturer specifications, sourcing information, pin-to-pin alternatives, comparison criteria, and practical circuit guidance to support faster component selection and PCB implementation. The LM393N/NOPB remains especially useful where two independent low-power comparator channels and a through-hole 8-pin footprint are required.
Alternativas directas para LM393N/NOPB — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LM393N/NOPB (mismo factor de forma y huella) — difiere en Comparator Type, Operating Temperature Range, Package, Mounting Type, Number of Comparators.
LM393N
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM393N
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM393N
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM393N/NOPB Valores máximos y características eléctricas
| Comparator Type | General-purpose dual comparator |
| Number of Comparators | 2 |
| Number of Independent Channels | 2 |
| Input Offset Voltage | 2.0 mV maximum |
| Supply Configuration | Single supply or split supply |
| Tipo de salida | Open-collector |
| Encapsulado | PDIP-8 |
| Recuento de pines | 8 pins |
| Rango de temperatura de funcionamiento | 0°C to +70°C |
| Tipo de montaje | Through-hole |
Guía de configuración de pines de LM393N/NOPB pdip-8
Configuración de pines para LM393N/NOPB (encapsulado pdip-8). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para LM393N/NOPB.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
LM393N/NOPB es adecuado para 6 aplicacións: Battery Voltage Threshold Detection, Industrial Sensor Limit Switching, Power-Supply Overvoltage Protection, Window Comparator Control, Motor and Relay Threshold Interface, Logic-Level and System Interfacing.
Battery Voltage Threshold Detection
The LM393N/NOPB fits battery monitoring because it combines two independent comparator channels, a 2.0 mV maximum input offset specification, and single-supply operation in one 8-pin PDIP package. One channel can compare a divided battery voltage with a reference to detect an overvoltage condition, while the other can monitor the opposite threshold. Each open-collector output can drive a pull-up and status LED or digital input. The design benefit is low component count, although input bias current can create errors with high-impedance dividers and the battery operating range must remain within the device's published supply and common-mode limits.
Recomendado
Industrial Sensor Limit Switching
The LM393N/NOPB is useful for industrial sensor interfaces that convert an analog level into a logic decision. Its two independent channels can monitor two sensor-derived voltages, such as a temperature threshold and a pressure threshold, without sharing internal signal paths. The 2.0 mV maximum offset specification helps preserve small transition margins, while the open-collector outputs allow pull-ups to the system's logic supply. Layout should keep input traces away from motors, relays, and switching power nodes, and the external reference network should have low enough impedance to minimize bias-current error.
Recomendado
Power-Supply Overvoltage Protection
LM393N/NOPB can supervise a power rail by comparing a scaled supply voltage against a stable reference and asserting an open-collector fault output when the monitored rail crosses a limit. Its two independent channels permit separate upper- and lower-bound supervision when both thresholds are required. The 8-pin PDIP format is particularly convenient for through-hole industrial boards, and open-collector outputs can be pulled up to the fault-system logic rail. The implementation must verify the input common-mode range at both extremes, account for resistor-divider tolerance, and ensure the pull-up voltage remains acceptable to every connected device.
Recomendado
Window Comparator Control
The two independent LM393N/NOPB channels can form a window comparator when one input of each channel receives a lower reference and the other receives an upper reference. The output state indicates whether the measured signal lies inside the permitted band. This arrangement benefits from the device's 2.0 mV maximum offset specification and low-power operation, while the open-collector outputs can be pulled up separately or combined through wired logic. Resistor matching and reference accuracy will often determine practical boundary accuracy, so use the resistor network and input bias current from the manufacturer datasheet to calculate worst-case threshold error.
Recomendado
Motor and Relay Threshold Interface
The LM393N/NOPB can convert motor-current, temperature, or position-sensor levels into control signals for relay and driver logic. Two channels allow a start/stop threshold pair to be evaluated independently, and the open-collector interface can operate at a pull-up voltage selected for the receiving logic. The through-hole PDIP package supports repairable industrial-control layouts. Because motor environments contain switching transients, comparator inputs and reference nodes should be physically separated from inductive and high-current paths, and suitable filtering should be designed without degrading the required response time.
Recomendado
Logic-Level and System Interfacing
LM393N/NOPB can bridge a low-voltage analog decision to a digital subsystem because its open-collector output can be pulled up to the voltage required by the receiving logic. A single device provides two independent channels for interlock, direction, or status signals. The architecture avoids the need for a dedicated push-pull line driver when wired logic is acceptable, although every pull-up must preserve valid input levels for the connected device. Confirm output sink-current capability, logic thresholds, response timing, and common-mode limits before using the part as a general-purpose logic translator.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM393N/NOPB — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM393N | LM393N | LM393N |
|---|---|---|---|---|
| Brand | Texas Instruments | onsemi | STMicroelectronics | Rochester Electronics |
| Package | 8-pin PDIP | 8-pin DIP | 8-pin DIP | 8-pin DIP |
| Comparator Configuration | Dual, independent comparator | Dual comparator | Dual comparator | Dual comparator |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins |
Diferenciadores clave
- Two independent channels in one through-hole package (frente a LM393N from STMicroelectronics)
- Documented low input offset specification (frente a LM393N from onsemi)
- Flexible open-collector output interface (frente a LM393N from Rochester Electronics)
Notas de diseño
Assign the PCB footprint from the manufacturer pin-description diagram rather than relying on the generic DIP outline. Keep each comparator's two input traces short and pair them away from switching nodes, relay coils, motor traces, and high-current return paths. Place the pull-up resistor associated with each open-collector output close to that output pin. For sensitive threshold measurements, use a quiet ground reference and avoid sharing narrow ground paths between the comparator and switching circuitry.
Do not treat the open-collector output as a push-pull logic output. Each low output must conduct current through a pull-up resistor, and the resistor voltage, power dissipation, and resulting rise time must be checked against the receiver's input requirements. Also verify that the sensed voltage remains inside the comparator's common-mode range. A supply voltage that is sufficient for operation does not automatically make every input voltage valid.
Account for input bias current when designing high-impedance resistor dividers. The bias current flowing through divider resistance produces an offset that can be comparable to the LM393N/NOPB's 2.0 mV maximum input offset specification. Use lower divider impedance when the source can drive it, or buffer the divider with a suitable low-input-bias amplifier when the sensor requires a high-impedance input.
Información de cumplimiento
The verified product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this general-purpose commercial comparator ordering.