SN74LS241N - Octal 3-State Buffer | Texas Instruments
MPN: SN74LS241N ✓ نشطSN74LS241N نظرة عامة
A buffer or line driver is a digital logic component that isolates a source from a load, provides signal gain, and improves drive capability within a logic system. The SN74LS241N hierarchy is octal buffer > non-inverting buffer > three-state line driver > bipolar logic IC > integrated circuit. Three-state outputs can place an output in the active-high, active-low, or high-impedance state, allowing multiple devices to share a data bus when only one driver is enabled at a time.
Each device contains eight non-inverting buffer elements. Two output-enable inputs control groups of four outputs, allowing two independently controlled four-bit sections. The three-state feature helps reduce bus contention, supports controlled disconnect from shared buses, and permits external test equipment to access nodes without permanently driving them. The NS suffix denotes the standard commercial-temperature ordering option, while N identifies the PDIP package.
The SN74LS241 uses bipolar LS-series logic technology at a nominal 5 V supply. The manufacturer product page specifies an 8-channel, 4.75 V to 5.25 V bipolar buffer with three-state outputs. Because the device is a buffer rather than a level shifter, its input and output voltage thresholds remain tied to the same 5 V LS logic environment. Power and timing behavior should be evaluated against the limits in the manufacturer datasheet for the selected load and temperature range.
Typical uses include computer peripheral data buses, bidirectional or multiplexed bus-interface sections, address and data-line buffering, industrial control systems, and legacy test equipment. The SN74LS241N is especially useful where a source must drive multiple loads or where two independently enabled four-bit groups need to share a common bus. It can also buffer control signals while leaving the corresponding output disconnected during a test or reset interval.
Keep input and output timing requirements in mind when cascading bus devices. The output-enable pins should be controlled so that two drivers never actively oppose each other on the same node. For a bus, designate an arbitration or priority scheme, disable all inactive drivers, and account for enable and propagation delays when changing ownership. Decoupling and unused input handling should follow the connection recommendations in the manufacturer datasheet.
This page organizes the SN74LS241N electrical characteristics, package details, drop-in alternatives, and application guidance for faster engineering evaluation. It also highlights the distinctions between enabled and high-impedance operation, identifies where the device differs from related LS-series buffers, and provides practical guidance for legacy-system repair, bus interfacing, and new multi-driver logic designs.
بدائل مباشرة لـ SN74LS241N — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
SN74LS241AN
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DM74LS241N
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN74LS241N
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DM74LS241AN
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
74LS241N
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN74LS241N الحدود القصوى والخصائص الكهربائية
| Logic Type | Octal buffer and line driver |
| Number of Channels | 8 channels |
| Bits per Element | 4 bits |
| نوع الخرج | 3-state output |
| Output Polarity | Non-inverting |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Logic Technology | Bipolar |
| Output-enable Control | 2 independent enable inputs controlling 4 outputs each |
| Package Type | 20-pin PDIP |
| نوع التركيب | Through-hole |
| Termination Style | Through-hole |
دليل تكوين أطراف SN74LS241N 20-pin pdip
تكوين الأطراف لـ SN74LS241N (حزمة 20-pin pdip). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SN74LS241N.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
SN74LS241N مناسب لـ 6 التطبيقs: Shared Peripheral Data Bus, Industrial Control Signal Buffering, Computer Peripheral Interface, Address-Line Buffering, Test and Measurement Systems, Embedded Control Interface.
Shared Peripheral Data Bus
The SN74LS241N fits a shared peripheral bus because its eight non-inverting channels provide buffered drive while two output-enable inputs control the device in two four-bit groups. One group can drive address, command, or data lines while the other remains in the high-impedance state, allowing another buffer to assume control. This arrangement improves load handling without reversing signal polarity. The 4.75 V to 5.25 V supply range matches a conventional 5 V LS-logic environment, and the 20-pin PDIP format supports through-hole construction or socketed legacy boards. Bus arbitration must prevent simultaneous activation of opposing drivers.
موصى به
Industrial Control Signal Buffering
The SN74LS241N can buffer control signals between a legacy controller and peripheral logic while preserving non-inverting Boolean behavior. Eight channels allow separate enable, reset, mode, and interlock signals to be distributed without loading the source outputs. The two four-channel enable groups also permit diagnostic circuitry to disconnect selected signals without taking the entire device off the bus. Operation across 4.75 V to 5.25 V supports conventional 5 V industrial control boards, while the through-hole PDIP package is practical for repairable equipment. Engineers should verify input thresholds, output-current capability, and timing against the connected loads before deployment.
موصى به
Computer Peripheral Interface
The SN74LS241N is useful in computer peripherals that require stronger signal drive or isolation between a processor bus and an external interface. Its non-inverting outputs preserve data and control-command polarity, while the three-state capability permits the peripheral connector to be disconnected during reset, isolation, or another device's bus access. The eight channels map naturally to groups of control lines or a four-bit data nibble plus associated controls. Its 4.75 V to 5.25 V operating range fits a 5 V interface, and the 20-pin PDIP package is common in older computer and instrumentation hardware. Timing checks should include both normal propagation and output-enable transitions.
موصى به
Address-Line Buffering
The SN74LS241N can buffer a four-bit address group and a second four-bit group without changing logic polarity. Two independently controlled enable sections help isolate memory or peripheral address buses when multiple devices share the same physical lines. During normal operation, one address group can drive while the other remains high impedance, reducing contention risk. The 5 V LS-series supply range is suitable for legacy processor boards, and the non-inverting characteristic avoids introducing address-bit inversions. In a design, confirm propagation-delay skew between the two groups, output loading, and the transition interval during which the previous bus owner is disabled and the next owner is enabled.
موصى به
Test and Measurement Systems
The SN74LS241N is appropriate for legacy test systems where a bus driver must connect to or disconnect from a shared measurement node. Disabling one four-output group places those drivers in a high-impedance state, allowing an external instrument or another circuit to take control without a permanent output conflict. The non-inverting paths simplify connection to TTL-compatible test fixtures. Its 4.75 V to 5.25 V operation fits 5 V instrumentation, while the 20-pin PDIP package supports repairable and socket-based designs. Instrumentation engineers should account for leakage from disabled outputs, enable timing, and the fact that the output characteristics must be checked for the intended load impedance.
موصى به
Embedded Control Interface
The SN74LS241N can interface a 5 V embedded-control board with external sensors, relays, counters, or legacy programmable logic. Eight buffered non-inverting channels help isolate the controller from heavier loads, while the two enable groups offer additional control over shared external nodes. Because the device supports three-state operation, selected outputs can remain disconnected during reset or test modes. The 4.75 V to 5.25 V supply range fits regulated 5 V systems, and the through-hole package is straightforward to assemble on industrial and educational controller boards. Confirm output sink and source ratings, fanout, and timing before driving relay drivers or other non-TTL-compatible loads.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ SN74LS241N — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | SN74LS241AN | DM74LS241N | SN74LS241N | DM74LS241AN | 74LS241N |
|---|---|---|---|---|---|---|
| Package | 20-PDIP | 20-PDIP | 20-PDIP | 20-PDIP | 20-PDIP | 20-PDIP |
| Brand | Texas Instruments | Texas Instruments | onsemi | onsemi | onsemi | Nexperia |
| Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Bits per Element | 4 bits | 4 bits | 4 bits | 4 bits | 4 bits | 4 bits |
| Output Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
| Output State | Three-state output | Three-state output | Three-state output | Three-state output | Three-state output | Three-state output |
| Logic Technology | Bipolar | Bipolar | Bipolar | Bipolar | Bipolar | Bipolar |
| Output-Enable Arrangement | 2 enable inputs controlling 4 outputs each | 2 enable inputs controlling 4 outputs each | 2 enable inputs controlling 4 outputs each | 2 enable inputs controlling 4 outputs each | 2 enable inputs controlling 4 outputs each | 2 enable inputs controlling 4 outputs each |
أبرز الفروقات
- Non-inverting three-state signal path (مقابلSN74LS244N)
- Two independently disabled four-channel groups (مقابلSN74LS240N)
- Standard 5 V bipolar operation (مقابلSN74LS541N)
- Direct manufacturer and cross-brand sourcing paths (مقابلDM74LS241N)
ملاحظات التصميم
Do not enable two drivers simultaneously when their outputs share a bus node. The SN74LS241N can place a four-output group in the high-impedance state, but two actively enabled outputs with opposite logic levels can cause excessive current, undefined voltage, and possible component damage. Use a common arbitration signal or non-overlapping enable sequence, and include enough dead time between turning one driver off and another on for the circuit to settle.
Treat output-enable transitions as timing events, not instantaneous control actions. Account for the difference between enable propagation delay and normal data propagation delay when changing bus ownership. Place the device close enough to the driven node to limit trace exposure, particularly when the output drives a cable, backplane, or long board interconnect. For high-speed or long-trace systems, verify ringing, loading, and timing against the manufacturer's recommended operating conditions.
Follow the manufacturer's pin-assignment and decoupling guidance when placing the 20-pin PDIP in a through-hole design. Keep power and ground connections short, provide the recommended bypass capacitor near the device, and route data and enable traces away from noisy switching nodes. Although the package is easy to socket for legacy repairs, production designs should consider whether the replacement will remain socketed and whether pin 1 orientation is consistent with the board artwork.
The SN74LS241N is designed for a 4.75 V to 5.25 V supply and is not a voltage-level translator for 3.3 V systems. Verify that every connected input remains within the logic's valid input range and that supply tolerance is acceptable across temperature and load. Multiple outputs can source or sink current simultaneously, so check both the per-channel and aggregate load limits from the manufacturer datasheet before driving backplanes, memories, or several external receivers.
معلومات الامتثال
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the cited product-page material. Obtain current manufacturer quality documentation before making a compliance claim.