Texas Instruments

SN74LS241N - Octal 3-State Buffer | Texas Instruments

MPN: SN74LS241N ✓ פעיל
4.75 V to 5.25 V Vdss 20-pin PDIP Package
כמות הזמנה מינימלית: 1 |

SN74LS241N סקירה

The Texas Instruments SN74LS241N is an octal, non-inverting buffer and line driver with eight 4-bit elements, individual output-enable control, and three-state outputs in a 20-pin PDIP package. The device operates from 4.75 V to 5.25 V and belongs to the LS-series bipolar logic family. Its buffered outputs provide stronger signal drive than ordinary TTL gates while preserving non-inverting logic behavior.

A buffer or line driver is a digital logic component that isolates a source from a load, provides signal gain, and improves drive capability within a logic system. The SN74LS241N hierarchy is octal buffer > non-inverting buffer > three-state line driver > bipolar logic IC > integrated circuit. Three-state outputs can place an output in the active-high, active-low, or high-impedance state, allowing multiple devices to share a data bus when only one driver is enabled at a time.

Each device contains eight non-inverting buffer elements. Two output-enable inputs control groups of four outputs, allowing two independently controlled four-bit sections. The three-state feature helps reduce bus contention, supports controlled disconnect from shared buses, and permits external test equipment to access nodes without permanently driving them. The NS suffix denotes the standard commercial-temperature ordering option, while N identifies the PDIP package.

The SN74LS241 uses bipolar LS-series logic technology at a nominal 5 V supply. The manufacturer product page specifies an 8-channel, 4.75 V to 5.25 V bipolar buffer with three-state outputs. Because the device is a buffer rather than a level shifter, its input and output voltage thresholds remain tied to the same 5 V LS logic environment. Power and timing behavior should be evaluated against the limits in the manufacturer datasheet for the selected load and temperature range.

Typical uses include computer peripheral data buses, bidirectional or multiplexed bus-interface sections, address and data-line buffering, industrial control systems, and legacy test equipment. The SN74LS241N is especially useful where a source must drive multiple loads or where two independently enabled four-bit groups need to share a common bus. It can also buffer control signals while leaving the corresponding output disconnected during a test or reset interval.

Keep input and output timing requirements in mind when cascading bus devices. The output-enable pins should be controlled so that two drivers never actively oppose each other on the same node. For a bus, designate an arbitration or priority scheme, disable all inactive drivers, and account for enable and propagation delays when changing ownership. Decoupling and unused input handling should follow the connection recommendations in the manufacturer datasheet.

This page organizes the SN74LS241N electrical characteristics, package details, drop-in alternatives, and application guidance for faster engineering evaluation. It also highlights the distinctions between enabled and high-impedance operation, identifies where the device differs from related LS-series buffers, and provides practical guidance for legacy-system repair, bus interfacing, and new multi-driver logic designs.

חלופות תחליף ישיר עבור SN74LS241N — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

SN74LS241AN

✅ Drop-In
📦 20-PDIP
Same 8-channel non-inverting three-state function and 4.75 V to 5.25 V supply; operating-temperature grade differs, while the 20-pin PDIP footprint and 0% voltage-range difference preserve pin compatibility.

📋 חלופה להתייחסות (לא בקטלוג)

DM74LS241N

✅ Drop-In
📦 20-PDIP
Same 8-channel non-inverting three-state buffer function and 4.75 V to 5.25 V supply; manufacturer qualification differs, with a 0% supply-range difference and matching 20-pin PDIP footprint.

📋 חלופה להתייחסות (לא בקטלוג)

SN74LS241N

✅ Drop-In
Texas Instruments
📦 20-PDIP
Octal buffer and line driver · 8 channels · 4 bits · 3-state output · Non-inverting · 4.75 V to 5.25 V · Bipolar · 2 independent enable inputs controlling 4 outputs each

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

DM74LS241AN

✅ Drop-In
📦 20-PDIP
Same non-inverting eight-channel three-state function and 4.75 V to 5.25 V supply; temperature-grade designation differs while voltage range, package, and logic function match.

📋 חלופה להתייחסות (לא בקטלוג)

74LS241N

✅ Drop-In
📦 20-PDIP
Same octal non-inverting three-state buffer function, matching 20-pin PDIP footprint, and 4.75 V to 5.25 V operating range; manufacturer-specific qualification and lifecycle terms differ.

📋 חלופה להתייחסות (לא בקטלוג)

SN74LS241N דירוגים מרביים ומאפיינים חשמליים

Logic Type Octal buffer and line driver
Number of Channels 8 channels
Bits per Element 4 bits
סוג פלט 3-state output
Output Polarity Non-inverting
Supply Voltage Range 4.75 V to 5.25 V
Logic Technology Bipolar
Output-enable Control 2 independent enable inputs controlling 4 outputs each
Package Type 20-pin PDIP
סוג הרכבה Through-hole
Termination Style Through-hole

מדריך תצורת פינים של SN74LS241N 20-pin pdip

תצורת פינים עבור SN74LS241N (מארזת 20-pin pdip). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.

תרשים פינים של מארזת 20-pin pdip עבור SN74LS241N

אין נתוני פריסת פינים מפורטים עבור SN74LS241N.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

SN74LS241N מתאים עבור 6 יישוםs: Shared Peripheral Data Bus, Industrial Control Signal Buffering, Computer Peripheral Interface, Address-Line Buffering, Test and Measurement Systems, Embedded Control Interface.

🖥️

Shared Peripheral Data Bus

The SN74LS241N fits a shared peripheral bus because its eight non-inverting channels provide buffered drive while two output-enable inputs control the device in two four-bit groups. One group can drive address, command, or data lines while the other remains in the high-impedance state, allowing another buffer to assume control. This arrangement improves load handling without reversing signal polarity. The 4.75 V to 5.25 V supply range matches a conventional 5 V LS-logic environment, and the 20-pin PDIP format supports through-hole construction or socketed legacy boards. Bus arbitration must prevent simultaneous activation of opposing drivers.

🏭

Industrial Control Signal Buffering

The SN74LS241N can buffer control signals between a legacy controller and peripheral logic while preserving non-inverting Boolean behavior. Eight channels allow separate enable, reset, mode, and interlock signals to be distributed without loading the source outputs. The two four-channel enable groups also permit diagnostic circuitry to disconnect selected signals without taking the entire device off the bus. Operation across 4.75 V to 5.25 V supports conventional 5 V industrial control boards, while the through-hole PDIP package is practical for repairable equipment. Engineers should verify input thresholds, output-current capability, and timing against the connected loads before deployment.

🖥️

Computer Peripheral Interface

The SN74LS241N is useful in computer peripherals that require stronger signal drive or isolation between a processor bus and an external interface. Its non-inverting outputs preserve data and control-command polarity, while the three-state capability permits the peripheral connector to be disconnected during reset, isolation, or another device's bus access. The eight channels map naturally to groups of control lines or a four-bit data nibble plus associated controls. Its 4.75 V to 5.25 V operating range fits a 5 V interface, and the 20-pin PDIP package is common in older computer and instrumentation hardware. Timing checks should include both normal propagation and output-enable transitions.

🔧

Address-Line Buffering

The SN74LS241N can buffer a four-bit address group and a second four-bit group without changing logic polarity. Two independently controlled enable sections help isolate memory or peripheral address buses when multiple devices share the same physical lines. During normal operation, one address group can drive while the other remains high impedance, reducing contention risk. The 5 V LS-series supply range is suitable for legacy processor boards, and the non-inverting characteristic avoids introducing address-bit inversions. In a design, confirm propagation-delay skew between the two groups, output loading, and the transition interval during which the previous bus owner is disabled and the next owner is enabled.

🔧

Test and Measurement Systems

The SN74LS241N is appropriate for legacy test systems where a bus driver must connect to or disconnect from a shared measurement node. Disabling one four-output group places those drivers in a high-impedance state, allowing an external instrument or another circuit to take control without a permanent output conflict. The non-inverting paths simplify connection to TTL-compatible test fixtures. Its 4.75 V to 5.25 V operation fits 5 V instrumentation, while the 20-pin PDIP package supports repairable and socket-based designs. Instrumentation engineers should account for leakage from disabled outputs, enable timing, and the fact that the output characteristics must be checked for the intended load impedance.

🤖

Embedded Control Interface

The SN74LS241N can interface a 5 V embedded-control board with external sensors, relays, counters, or legacy programmable logic. Eight buffered non-inverting channels help isolate the controller from heavier loads, while the two enable groups offer additional control over shared external nodes. Because the device supports three-state operation, selected outputs can remain disconnected during reset or test modes. The 4.75 V to 5.25 V supply range fits regulated 5 V systems, and the through-hole package is straightforward to assemble on industrial and educational controller boards. Confirm output sink and source ratings, fanout, and timing before driving relay drivers or other non-TTL-compatible loads.

What is the SN74LS241N?
The SN74LS241N is an octal, non-inverting bipolar buffer and line driver with three-state outputs. According to the Texas Instruments product page, it contains eight 4-bit channels, operates from 4.75 V to 5.25 V, and uses two output-enable inputs to control four outputs per group. The device is packaged in a 20-pin PDIP and is intended for buffered bus-interface, control-signal, and legacy digital-system designs.
Where can I download the SN74LS241N datasheet PDF?
The SN74LS241N datasheet and ordering information are available from the official Texas Instruments product page for SN74LS241. The manufacturer documentation describes the device as an eight-channel, 4.75 V to 5.25 V bipolar buffer with three-state outputs. Use the pin-description table, recommended operating conditions, and timing diagrams in that document before assigning PCB signals or designing a replacement.
Where can I find the SN74LS241N pinout?
The SN74LS241N pinout is defined in the manufacturer datasheet for the 20-pin PDIP package. The package contains eight non-inverting data inputs, eight corresponding outputs, two output-enable inputs, and power and ground connections. The SN74LS241N combines four channels under each enable input. Always use the exact pin-description table when making a board revision because related 74LS buffer functions do not always have identical enable behavior.
How does the SN74LS241N differ from the SN74LS244N?
The SN74LS241N has non-inverting outputs, while the SN74LS244N provides inverting outputs. Both are octal three-state LS-series buffers in 20-pin PDIP packages, so their physical footprints correspond, but substituting one for the other reverses the logical signal at every active data output. The SN74LS241N is the correct choice when the receiving circuit expects the same logic state at its input and output.
What is the difference between SN74LS241N and SN74LS240N?
The principal functional difference is output polarity: SN74LS241N has non-inverting outputs, whereas SN74LS240N has inverting outputs. Both devices provide eight channels and three-state output capability in the same 20-pin PDIP package. Although the footprints match, an SN74LS240N changes the Boolean relationship at every enabled data output. Choose the SN74LS241N when data must pass through without inversion.
When should I choose the SN74LS241N over an inverting 74LS buffer?
Choose the SN74LS241N when the output must preserve the input logic level and also provide stronger drive or bus isolation. Its eight non-inverting channels include individual three-state control through two enable inputs, allowing four outputs to be connected or disconnected as a group. An inverting 74LS buffer is preferable only when inversion is intentional and downstream logic is designed accordingly.
Is the SN74LS241N suitable for a shared data bus?
The SN74LS241N is suitable for a shared bus when only one output group is enabled at a time. Its three-state outputs allow disabled drivers to enter a high-impedance state instead of actively driving the bus. The design must prevent two enabled drivers from opposing each other, and it must account for output-enable timing before ownership changes. Suitable applications include peripheral, data, and address buses in legacy TTL systems.
What can replace the SN74LS241N?
A valid replacement must use a 20-pin PDIP, preserve eight non-inverting channels, retain three-state outputs, and match the 4.75 V to 5.25 V supply range. Suitable same-function choices include SN74LS241AN from Texas Instruments and compatible 74LS241N or DM74LS241N devices from other logic manufacturers. Confirm pinout, enable polarity, timing, output-current capability, temperature grade, and lifecycle status before approving a substitution.
What is the best cross-brand equivalent for the SN74LS241N?
The DM74LS241N and compatible 74LS241N devices from established logic manufacturers can serve as cross-brand alternatives when they retain the 20-pin PDIP footprint and identical three-state, non-inverting function. The Texas Instruments product specification defines the electrical target as eight channels, four bits per element, a 4.75 V to 5.25 V supply, and two enable-controlled output groups. Confirm the selected manufacturer's timing and enable-polarity details against the system requirements.
Can SN74LS241N replace SN74LS244N without changing the PCB?
The SN74LS241N has the same 20-pin PDIP footprint and three-state bus-control function as the SN74LS244N, but its outputs are non-inverting rather than inverting. Therefore, it is not a functionally equivalent substitution for SN74LS244N unless every affected signal path can tolerate inversion. A footprint match alone does not make the devices interchangeable in digital logic.
Where can I buy SN74LS241N online?
Use the Request a Quote form on this page to request SN74LS241N availability, current commercial terms, and a delivery quotation. The request should state the exact 20-pin PDIP orderable MPN, target quantity, and any required date. The Texas Instruments product page provides the authoritative package and ordering information needed to avoid accidentally requesting a different package or temperature option.
What is the lead time for SN74LS241N?
Request the current SN74LS241N lead time through the Request a Quote form on this page. Include the quantity, authorized ship-to region, and whether sealed production packaging is required. Because inventory and scheduling can change independently of the device's electrical characteristics, the manufacturer and supply channel should confirm the most current lead time for the exact 20-pin PDIP part number.
Is SN74LS241N in stock?
Check current SN74LS241N availability through the Request a Quote form on this page. Provide the required quantity, packaging preference, and delivery date so the supply channel can confirm an allocation. The device's listing status is not a guarantee of physical inventory, and no stock claim should be made solely from a catalog or comparison page.
What are the key specifications of SN74LS241N that engineers should know?
The SN74LS241N is an octal, non-inverting, three-state buffer and line driver operating at 4.75 V to 5.25 V. According to the Texas Instruments product page, it has eight 4-bit channels in a 20-pin PDIP package. Two output-enable inputs control four channels each, allowing two independently enabled output groups to drive or disconnect from shared nodes. Its principal engineering considerations are enable polarity, bus contention avoidance, propagation timing, and load-current limits.
Is the SN74LS241N RoHS compliant?
Use the manufacturer product and quality documentation for the definitive environmental and material-compliance status of the current SN74LS241N orderable part. The device is a standard 20-pin PDIP LS-series logic component, but package construction and regional handling requirements should not be used to infer RoHS, REACH, lead-free, or conflict-minerals declarations. Request current compliance documentation before shipping the part into restricted markets.
What are the main applications of the SN74LS241N?
The SN74LS241N is used for bus buffering, address-line buffering, peripheral interfacing, control-signal isolation, test-point multiplexing, and legacy 5 V digital equipment. Its non-inverting outputs preserve logic levels, while the two enable inputs permit one four-channel group to remain high impedance while the other drives. The application must manage bus ownership so that two active three-state drivers never source and sink the same node simultaneously.

נתוני עזר הנדסיים עבור SN74LS241N — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the SN74LS241N when a legacy 5 V system needs eight non-inverting buffered channels with three-state outputs and two independently controlled four-output groups. It is a strong fit for shared peripheral buses, address buffering, control-signal isolation, and repair of through-hole TTL boards. Select SN74LS241AN when the system documentation requires the Texas Instruments suffix option or a specific temperature grade. Consider DM74LS241N, DM74LS241AN, or 74LS241N when a second qualified source with the same 20-pin PDIP function is desirable. Do not choose an SN74LS244N or SN74LS240N as a direct substitution unless inversion is acceptable. Before approving any alternative, verify enable polarity, propagation timing, load-current limits, temperature range, and lifecycle status. The SN74LS241N is a logic-family device rather than a modern level translator, so it should only be used when the system voltage and signal thresholds are compatible with 5 V LS logic.

השוואה עם חלופות

פרמטר מוצר זה SN74LS241AN DM74LS241N SN74LS241N DM74LS241AN 74LS241N
Package 20-PDIP 20-PDIP 20-PDIP 20-PDIP 20-PDIP 20-PDIP
Brand Texas Instruments Texas Instruments onsemi onsemi onsemi Nexperia
Supply Voltage Range 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V 4.75 V to 5.25 V
Number of Channels 8 channels 8 channels 8 channels 8 channels 8 channels 8 channels
Bits per Element 4 bits 4 bits 4 bits 4 bits 4 bits 4 bits
Output Polarity Non-inverting Non-inverting Non-inverting Non-inverting Non-inverting Non-inverting
Output State Three-state output Three-state output Three-state output Three-state output Three-state output Three-state output
Logic Technology Bipolar Bipolar Bipolar Bipolar Bipolar Bipolar
Output-Enable Arrangement 2 enable inputs controlling 4 outputs each 2 enable inputs controlling 4 outputs each 2 enable inputs controlling 4 outputs each 2 enable inputs controlling 4 outputs each 2 enable inputs controlling 4 outputs each 2 enable inputs controlling 4 outputs each

מבדילים עיקריים

  • Non-inverting three-state signal path (לעומתSN74LS244N)
  • Two independently disabled four-channel groups (לעומתSN74LS240N)
  • Standard 5 V bipolar operation (לעומתSN74LS541N)
  • Direct manufacturer and cross-brand sourcing paths (לעומתDM74LS241N)

הערות תכנון

Do not enable two drivers simultaneously when their outputs share a bus node. The SN74LS241N can place a four-output group in the high-impedance state, but two actively enabled outputs with opposite logic levels can cause excessive current, undefined voltage, and possible component damage. Use a common arbitration signal or non-overlapping enable sequence, and include enough dead time between turning one driver off and another on for the circuit to settle.

Treat output-enable transitions as timing events, not instantaneous control actions. Account for the difference between enable propagation delay and normal data propagation delay when changing bus ownership. Place the device close enough to the driven node to limit trace exposure, particularly when the output drives a cable, backplane, or long board interconnect. For high-speed or long-trace systems, verify ringing, loading, and timing against the manufacturer's recommended operating conditions.

Follow the manufacturer's pin-assignment and decoupling guidance when placing the 20-pin PDIP in a through-hole design. Keep power and ground connections short, provide the recommended bypass capacitor near the device, and route data and enable traces away from noisy switching nodes. Although the package is easy to socket for legacy repairs, production designs should consider whether the replacement will remain socketed and whether pin 1 orientation is consistent with the board artwork.

The SN74LS241N is designed for a 4.75 V to 5.25 V supply and is not a voltage-level translator for 3.3 V systems. Verify that every connected input remains within the logic's valid input range and that supply tolerance is acceptable across temperature and load. Multiple outputs can source or sink current simultaneously, so check both the per-channel and aggregate load limits from the manufacturer datasheet before driving backplanes, memories, or several external receivers.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the cited product-page material. Obtain current manufacturer quality documentation before making a compliance claim.

חיפושים קשורים

sn74ls241n datasheet SN74LS241N SN74LS241N datasheet pdf SN74LS241N pinout SN74LS241N 20-PDIP SN74LS241N voltage range SN74LS241N three-state outputs SN74LS241N equivalent SN74LS241N replacement SN74LS241N vs SN74LS244N SN74LS241N application circuit SN74LS241N price SN74LS241N stock

רכיבים ומונחים קשורים

Texas Instruments SN74LS241N SN74LS241AN DM74LS241N DM74LS241AN 74LS241N SN74LS244N SN74LS240N SN74LS541N octal buffer non-inverting buffer three-state line driver bipolar logic IC LS-series TTL logic three-state output output-enable input high-impedance state bus arbitration 4.75 V to 5.25 V supply 20-pin PDIP PDIP package family through-hole logic legacy computer peripheral industrial control system RoHS
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר