THS3092DDA - Dual 160MHz CFA | Texas Instruments | SOIC-8
MPN: THS3092DDA ✓ نشطTHS3092DDA نظرة عامة
A current-feedback operational amplifier, or CFA, is a voltage-amplifier architecture organized around a low-impedance inverting input and a feedback impedance that sets closed-loop gain. Unlike a voltage-feedback amplifier, a CFA maintains high bandwidth across a wide gain range and delivers high slew rate with minimal gain-bandwidth degradation. In the power-management hierarchy, the THS3092DDA belongs to the operational-amplifier and signal-conditioning IC family rather than the voltage-regulator category.
The principal performance features include 160 MHz bandwidth, 5700 V/µs slew rate, and total harmonic distortion as low as −66 dBc at 10 MHz. The wide ±5 V to ±15 V supply range supports bipolar operation with a maximum total supply span of 30 V. Its current-feedback architecture is particularly useful for driving capacitive and high-resistance loads while maintaining large voltage swings and good settling performance.
The two-amplifier configuration provides two independent channels in a compact 8-pin HSOIC PowerPAD package. The exposed thermal pad supports heat transfer into the PCB copper area, an important consideration because high-speed, high-swing operation can increase device dissipation. The manufacturer identifies the THS3092 family for high-voltage arbitrary-waveform driver applications, including line-driver and power-driver signal-conditioning stages.
Typical uses include waveform generation, communications line-interface amplification, video and test-equipment output stages, power MOSFET or power-FET gate-drive signal conditioning, and VDSL-related driver circuits. The ±15 V capability and 5700 V/µs slew rate make the amplifier appropriate when a clean, large-amplitude output must follow a high-speed input waveform.
PCB design should keep feedback traces short, provide a low-impedance ground return for the exposed pad, and place supply-decoupling capacitors close to the relevant pins. Current-feedback amplifiers require suitable feedback resistors for the intended gain and load; incorrect values can produce excessive peaking, oscillation, or poor settling. Confirm output-current and capacitive-load limits before finalizing a driver stage.
This product page combines the manufacturer’s device description with package details, engineering selection guidance, verified ordering information, and practical design considerations. It is intended to help engineers identify whether the THS3092DDA’s high-voltage, high-speed dual-amplifier capability matches their signal-chain requirements.
بدائل مباشرة لـ THS3092DDA — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع THS3092DDA (نفس عامل الشكل والبصمة) — يختلف في Package.
THS3096DDA
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
THS3092DDA الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Dual current-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 160 MHz |
| Slew Rate | 5700 V/µs |
| Total Harmonic Distortion | −66 dBc at 10 MHz |
| Supply Voltage Range | ±5 V to ±15 V |
| Maximum Total Supply Span | 30 V |
| العلبة | 8-pin HSOIC PowerPAD (DDA) |
| نوع التركيب | Surface mount |
دليل تكوين أطراف THS3092DDA 8-pin hsoic powerpad (dda)
تكوين الأطراف لـ THS3092DDA (حزمة 8-pin hsoic powerpad (dda)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ THS3092DDA.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
THS3092DDA مناسب لـ 6 التطبيقs: High-Voltage Arbitrary Waveform Drivers, VDSL and Communications Line Drivers, Power MOSFET Gate-Drive Conditioning, Video and Instrumentation Output Stages, High-Speed Sensor Signal Conditioning, Industrial and Factory Control Interfaces.
High-Voltage Arbitrary Waveform Drivers
The THS3092DDA fits waveform-driver stages that require large output voltage swings at high frequency. Its 160 MHz bandwidth, 5700 V/µs slew rate, and low distortion as low as −66 dBc at 10 MHz help preserve the shape of demanding output waveforms. The device can be placed at the final drive stage of an arbitrary-waveform generator, with the feedback network selected using the manufacturer’s recommended values. The ±5 V to ±15 V supply range supports bipolar drive requirements, while the exposed PowerPAD needs adequate PCB copper for heat removal.
موصى به
VDSL and Communications Line Drivers
The THS3092DDA is suitable for communications line-drive signal conditioning where large, fast output transitions are required. A current-feedback amplifier provides high large-signal capability through its 5700 V/µs slew rate, while the 160 MHz bandwidth supports high-frequency channel content. With bipolar supplies up to ±15 V, the device offers the voltage headroom needed to drive downstream circuitry through an external line-driver stage. Feedback impedance, load capacitance, and output-current requirements must be checked against the datasheet before the amplifier is connected to the line interface.
موصى به
Power MOSFET Gate-Drive Conditioning
The THS3092DDA can condition high-rate gate-drive commands for power MOSFETs and power FETs when the driver system requires a large, fast bipolar voltage swing. The 5700 V/µs slew rate supports rapid input transitions, and the 160 MHz bandwidth provides bandwidth for high-frequency gate-drive waveforms. The amplifier is normally used before a dedicated MOSFET driver because its output-current and capacitive-load limits must support the gate charge and wiring capacitance. Place it close to the driver input, minimize feedback-loop area, and use independent rail decoupling.
موصى به
Video and Instrumentation Output Stages
The dual THS3092DDA can provide two high-speed output channels in video, laboratory, and test-instrumentation signal chains. Its 160 MHz bandwidth and 5700 V/µs slew rate are useful when driving terminated or capacitive loads and reproducing large-amplitude waveforms. The dual architecture saves board area compared with two separate single amplifiers, while the 8-pin HSOIC PowerPAD package provides a direct thermal path to the PCB. The exact gain-setting resistor and output-swing limits must follow the manufacturer’s application guidance for the chosen load.
موصى به
High-Speed Sensor Signal Conditioning
The THS3092DDA can serve as a fast output stage in sensor signal-conditioning systems that need to drive longer cables or downstream instrumentation rather than operate as a low-noise precision input amplifier. Its large-signal bandwidth, 160 MHz bandwidth, and 5700 V/µs slew rate help retain signal amplitude through downstream stages. The dual-channel configuration can process complementary or separate channels. Because it is a current-feedback amplifier, impedance at the inverting input and feedback network must be controlled to achieve the intended bandwidth and stability.
موصى به
Industrial and Factory Control Interfaces
The THS3092DDA is appropriate for industrial control interfaces that must amplify fast control signals into larger-amplitude drive levels. The ±5 V to ±15 V operating range supports industrial bipolar signal chains, while the 5700 V/µs slew rate preserves rapid transitions. Two amplifiers in one package allow compact implementation of complementary drive or dual-axis control outputs. Thermal design remains important when both channels operate continuously into demanding loads; connect the exposed pad to an adequate copper area and follow the package’s soldering and layout requirements.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ THS3092DDA — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | THS3096DDA |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin HSOIC PowerPAD (DDA) | 8-pin HSOIC PowerPAD (DDA) |
| Amplifier Architecture | Current feedback | Current feedback |
| Channel Count | 2 channels | 2 channels |
| Supply Voltage Range | ±5 V to ±15 V | ±5 V to ±15 V |
| Primary Application | High-voltage arbitrary-waveform and line driving | High-voltage current-feedback waveform driving |
أبرز الفروقات
- High large-signal slew capability (مقابلOP293FSZ-REEL7)
- Wide bipolar operating range (مقابلOP293FSZ-REEL7)
- Integrated dual amplifier and exposed thermal pad (مقابلSSM2135SZ-REEL7)
ملاحظات التصميم
Route the inverting input and feedback resistor directly between the amplifier and the feedback component, with minimal loop area and no test pads or unnecessary copper in the feedback path. Current-feedback amplifiers respond to feedback impedance, so even a small parasitic capacitance or inductance can alter bandwidth, peaking, and settling. Keep the feedback network close to the relevant pins and provide a low-impedance return from the exposed thermal pad to the circuit ground plane.
Place the positive and negative supply-decoupling capacitors close to their corresponding pins and keep each return path short. Because the THS3092DDA supports a total supply span of 30 V, verify rail polarity and absolute maximum limits during power-up. A controlled sequence and adequate bypass capacitance help prevent output transients during rail changes; use the manufacturer’s recommended network when the output must remain inactive during startup.
Treat the 8-pin HSOIC PowerPad as both an electrical connection and a thermal path. Connect the exposed pad to a continuous copper area with multiple thermal-via connections and maintain the package’s land-pattern requirements. Estimated: operation near ±15 V can create substantial dissipation when both channels deliver large output swings, so calculate worst-case channel output power and confirm that the PCB copper area can maintain the required junction-temperature margin.
Do not select feedback resistance solely from the intended closed-loop voltage gain. Current-feedback amplifiers require the manufacturer’s recommended feedback impedance for the target gain, output amplitude, and load. Increasing resistance excessively may reduce bandwidth or increase noise, while an excessively low value may increase output-current demand. Also verify capacitive-load stability and avoid driving loads beyond the datasheet output-current and slew-rate limits.
معلومات الامتثال
The manufacturer product family is identified, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the cited product text. AEC-Q100 is not applicable because THS3092DDA is not presented as an automotive-qualified device.