THS3092DDA - Dual 160MHz CFA | Texas Instruments | SOIC-8
部品番号: THS3092DDA ✓ 生産中THS3092DDA 概要
A current-feedback operational amplifier, or CFA, is a voltage-amplifier architecture organized around a low-impedance inverting input and a feedback impedance that sets closed-loop gain. Unlike a voltage-feedback amplifier, a CFA maintains high bandwidth across a wide gain range and delivers high slew rate with minimal gain-bandwidth degradation. In the power-management hierarchy, the THS3092DDA belongs to the operational-amplifier and signal-conditioning IC family rather than the voltage-regulator category.
The principal performance features include 160 MHz bandwidth, 5700 V/µs slew rate, and total harmonic distortion as low as −66 dBc at 10 MHz. The wide ±5 V to ±15 V supply range supports bipolar operation with a maximum total supply span of 30 V. Its current-feedback architecture is particularly useful for driving capacitive and high-resistance loads while maintaining large voltage swings and good settling performance.
The two-amplifier configuration provides two independent channels in a compact 8-pin HSOIC PowerPAD package. The exposed thermal pad supports heat transfer into the PCB copper area, an important consideration because high-speed, high-swing operation can increase device dissipation. The manufacturer identifies the THS3092 family for high-voltage arbitrary-waveform driver applications, including line-driver and power-driver signal-conditioning stages.
Typical uses include waveform generation, communications line-interface amplification, video and test-equipment output stages, power MOSFET or power-FET gate-drive signal conditioning, and VDSL-related driver circuits. The ±15 V capability and 5700 V/µs slew rate make the amplifier appropriate when a clean, large-amplitude output must follow a high-speed input waveform.
PCB design should keep feedback traces short, provide a low-impedance ground return for the exposed pad, and place supply-decoupling capacitors close to the relevant pins. Current-feedback amplifiers require suitable feedback resistors for the intended gain and load; incorrect values can produce excessive peaking, oscillation, or poor settling. Confirm output-current and capacitive-load limits before finalizing a driver stage.
This product page combines the manufacturer’s device description with package details, engineering selection guidance, verified ordering information, and practical design considerations. It is intended to help engineers identify whether the THS3092DDA’s high-voltage, high-speed dual-amplifier capability matches their signal-chain requirements.
ドロップイン代替品: THS3092DDA — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: THS3092DDA (同一形状・フットプリント) — 相違点: Package.
THS3096DDA
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
THS3092DDA 最大定格&電気的特性
| Amplifier Type | Dual current-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 160 MHz |
| Slew Rate | 5700 V/µs |
| Total Harmonic Distortion | −66 dBc at 10 MHz |
| Supply Voltage Range | ±5 V to ±15 V |
| Maximum Total Supply Span | 30 V |
| パッケージ | 8-pin HSOIC PowerPAD (DDA) |
| 実装タイプ | Surface mount |
THS3092DDA 8-pin hsoic powerpad (dda) ピン配置ガイド
THS3092DDA (8-pin hsoic powerpad (dda) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: THS3092DDA.
詳細は データシート をご参照ください。
主な用途
THS3092DDA の用途: 6 件s: High-Voltage Arbitrary Waveform Drivers, VDSL and Communications Line Drivers, Power MOSFET Gate-Drive Conditioning, Video and Instrumentation Output Stages, High-Speed Sensor Signal Conditioning, Industrial and Factory Control Interfaces.
High-Voltage Arbitrary Waveform Drivers
The THS3092DDA fits waveform-driver stages that require large output voltage swings at high frequency. Its 160 MHz bandwidth, 5700 V/µs slew rate, and low distortion as low as −66 dBc at 10 MHz help preserve the shape of demanding output waveforms. The device can be placed at the final drive stage of an arbitrary-waveform generator, with the feedback network selected using the manufacturer’s recommended values. The ±5 V to ±15 V supply range supports bipolar drive requirements, while the exposed PowerPAD needs adequate PCB copper for heat removal.
おすすめ
VDSL and Communications Line Drivers
The THS3092DDA is suitable for communications line-drive signal conditioning where large, fast output transitions are required. A current-feedback amplifier provides high large-signal capability through its 5700 V/µs slew rate, while the 160 MHz bandwidth supports high-frequency channel content. With bipolar supplies up to ±15 V, the device offers the voltage headroom needed to drive downstream circuitry through an external line-driver stage. Feedback impedance, load capacitance, and output-current requirements must be checked against the datasheet before the amplifier is connected to the line interface.
おすすめ
Power MOSFET Gate-Drive Conditioning
The THS3092DDA can condition high-rate gate-drive commands for power MOSFETs and power FETs when the driver system requires a large, fast bipolar voltage swing. The 5700 V/µs slew rate supports rapid input transitions, and the 160 MHz bandwidth provides bandwidth for high-frequency gate-drive waveforms. The amplifier is normally used before a dedicated MOSFET driver because its output-current and capacitive-load limits must support the gate charge and wiring capacitance. Place it close to the driver input, minimize feedback-loop area, and use independent rail decoupling.
おすすめ
Video and Instrumentation Output Stages
The dual THS3092DDA can provide two high-speed output channels in video, laboratory, and test-instrumentation signal chains. Its 160 MHz bandwidth and 5700 V/µs slew rate are useful when driving terminated or capacitive loads and reproducing large-amplitude waveforms. The dual architecture saves board area compared with two separate single amplifiers, while the 8-pin HSOIC PowerPAD package provides a direct thermal path to the PCB. The exact gain-setting resistor and output-swing limits must follow the manufacturer’s application guidance for the chosen load.
おすすめ
High-Speed Sensor Signal Conditioning
The THS3092DDA can serve as a fast output stage in sensor signal-conditioning systems that need to drive longer cables or downstream instrumentation rather than operate as a low-noise precision input amplifier. Its large-signal bandwidth, 160 MHz bandwidth, and 5700 V/µs slew rate help retain signal amplitude through downstream stages. The dual-channel configuration can process complementary or separate channels. Because it is a current-feedback amplifier, impedance at the inverting input and feedback network must be controlled to achieve the intended bandwidth and stability.
おすすめ
Industrial and Factory Control Interfaces
The THS3092DDA is appropriate for industrial control interfaces that must amplify fast control signals into larger-amplitude drive levels. The ±5 V to ±15 V operating range supports industrial bipolar signal chains, while the 5700 V/µs slew rate preserves rapid transitions. Two amplifiers in one package allow compact implementation of complementary drive or dual-axis control outputs. Thermal design remains important when both channels operate continuously into demanding loads; connect the exposed pad to an adequate copper area and follow the package’s soldering and layout requirements.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: THS3092DDA — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | THS3096DDA |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin HSOIC PowerPAD (DDA) | 8-pin HSOIC PowerPAD (DDA) |
| Amplifier Architecture | Current feedback | Current feedback |
| Channel Count | 2 channels | 2 channels |
| Supply Voltage Range | ±5 V to ±15 V | ±5 V to ±15 V |
| Primary Application | High-voltage arbitrary-waveform and line driving | High-voltage current-feedback waveform driving |
主な差別化要因
- High large-signal slew capability (vs OP293FSZ-REEL7)
- Wide bipolar operating range (vs OP293FSZ-REEL7)
- Integrated dual amplifier and exposed thermal pad (vs SSM2135SZ-REEL7)
設計ノート
Route the inverting input and feedback resistor directly between the amplifier and the feedback component, with minimal loop area and no test pads or unnecessary copper in the feedback path. Current-feedback amplifiers respond to feedback impedance, so even a small parasitic capacitance or inductance can alter bandwidth, peaking, and settling. Keep the feedback network close to the relevant pins and provide a low-impedance return from the exposed thermal pad to the circuit ground plane.
Place the positive and negative supply-decoupling capacitors close to their corresponding pins and keep each return path short. Because the THS3092DDA supports a total supply span of 30 V, verify rail polarity and absolute maximum limits during power-up. A controlled sequence and adequate bypass capacitance help prevent output transients during rail changes; use the manufacturer’s recommended network when the output must remain inactive during startup.
Treat the 8-pin HSOIC PowerPad as both an electrical connection and a thermal path. Connect the exposed pad to a continuous copper area with multiple thermal-via connections and maintain the package’s land-pattern requirements. Estimated: operation near ±15 V can create substantial dissipation when both channels deliver large output swings, so calculate worst-case channel output power and confirm that the PCB copper area can maintain the required junction-temperature margin.
Do not select feedback resistance solely from the intended closed-loop voltage gain. Current-feedback amplifiers require the manufacturer’s recommended feedback impedance for the target gain, output amplitude, and load. Increasing resistance excessively may reduce bandwidth or increase noise, while an excessively low value may increase output-current demand. Also verify capacitive-load stability and avoid driving loads beyond the datasheet output-current and slew-rate limits.
コンプライアンス情報
The manufacturer product family is identified, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the cited product text. AEC-Q100 is not applicable because THS3092DDA is not presented as an automotive-qualified device.