CD4060BCM - 14-Stage Binary Counter | onsemi | SOIC-16
MPN: CD4060BCM ✓ সক্রিয়CD4060BCM সারাংশ
A binary counter is a sequential logic device that records a number of clock transitions and presents that count through digital output stages. The CD4060B family combines a 14-stage ripple-carry counter with oscillator capability, placing it within the hierarchy of CMOS logic IC, counter/divider, digital logic, and semiconductor timing devices. Its negative-edge clock response and fixed divide stages help designers produce predictable frequency relationships from an input clock.
The CD4060BCM is specified as a 4000-series CMOS counter/divider with a 16-pin SOIC format. Its operating temperature range is listed as -55°C to +125°C in the manufacturer-related datasheet information, making it suitable for industrial temperature environments when the circuit's voltage and timing requirements are met. The counter structure supports applications requiring binary-coded timing information, such as programmable timers, delay generators, pulse-rate dividers, and clocked sequencing systems.
The CD4060BCM uses negative-edge clocking, so the output state changes when the clock input transitions from high to low. In a practical implementation, the oscillator section may use external resistors and a capacitor, or an external clock may drive the counter. Designers should account for ripple propagation across the 14 stages when the outputs are used as a coherent binary word, and should preserve adequate clock and output rise times in long-chain timing applications.
Typical uses include industrial timer modules, frequency-divider circuits, pulse-counting instrumentation, periodic event generation, and embedded control systems requiring a compact binary counter. Because the CD4060BCM is a CMOS counter/divider rather than a general-purpose microcontroller, it can reduce firmware overhead when a fixed counter and divider function is sufficient. It is also useful as a building block in legacy CMOS designs where a known 16-pin SOIC footprint and established CD4060B behavior simplify maintenance.
For new layouts, place decoupling capacitors close to the power pins and route clock and oscillator traces away from noisy switching nodes. Verify the allowable supply voltage, oscillator component tolerances, maximum clock frequency, and output load against the manufacturer datasheet before production. The CD4060BCM is best suited to designs that need deterministic binary counting rather than programmable arithmetic or bidirectional counting.
This product page combines the manufacturer's counter description, package and temperature information, compatibility-oriented alternatives, and application-specific engineering guidance to support faster component selection and PCB design. It also highlights the distinction between a fixed CMOS ripple counter/divider and more programmable timing devices.
এর জন্য ড্রপ-ইন বিকল্প CD4060BCM — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible CD4060BCM (একই form factor এবং footprint) — পার্থক্য রয়েছে Counter Resolution, Logic Family, Package, Product Type.
CD4060BMG4
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
CD4060BCMX
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
CD4060BMT
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →CD4060BM
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →CD4060BCM সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | 14-stage ripple-carry binary counter/divider |
| Logic Family | 4000-series CMOS |
| Number of Counter Stages | 14 stages |
| Counter Resolution | 14 bits |
| Counter Elements | 1 element |
| Clock Edge | Negative edge |
| সাপ্লাই ভোল্টেজ | 15 V maximum |
| অপারেটিং তাপমাত্রার পরিসর | -55°C to +125°C |
| প্যাকেজ | 16-pin SOIC |
| পিনের সংখ্যা | 16 pins |
| মাউন্টিং টাইপ | Surface mount |
| Logic Type | Binary counter/divider |
| Oscillator Function | RC oscillator capable |
| আউটপুট কনফিগারেশন | Binary counter outputs |
CD4060BCM পিন কনফিগারেশন
| পিন 1 | [DATA_NEEDED: pin 1 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 2 | [DATA_NEEDED: pin 2 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 3 | [DATA_NEEDED: pin 3 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 4 | [DATA_NEEDED: pin 4 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 5 | [DATA_NEEDED: pin 5 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 6 | [DATA_NEEDED: pin 6 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 7 | [DATA_NEEDED: pin 7 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 8 | [DATA_NEEDED: pin 8 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 9 | [DATA_NEEDED: pin 9 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 10 | [DATA_NEEDED: pin 10 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 11 | [DATA_NEEDED: pin 11 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 12 | [DATA_NEEDED: pin 12 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 13 | [DATA_NEEDED: pin 13 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 14 | [DATA_NEEDED: pin 14 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 15 | [DATA_NEEDED: pin 15 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
| পিন 16 | [DATA_NEEDED: pin 16 name] — Consult the manufacturer datasheet pin-description table before assigning the PCB net. |
সাধারণ ব্যবহার
CD4060BCM এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Programmable Timer Module, Frequency Divider, Industrial Pulse Counter, Periodic Event Generator, Clocked Sequencing System, Oscillator-Based Timebase.
Programmable Timer Module
The onsemi CD4060BCM fits a programmable timer module because it combines a 14-stage binary counter with oscillator capability in a 16-pin SOIC package. It can establish a timing cadence with external resistor-capacitor components and present elapsed-count information through binary outputs. This removes a microcontroller and its firmware from simple interval or delayed-event tasks, reducing board complexity. The design must follow the manufacturer oscillator values, verify start-up behavior, and include tolerance analysis for the timing components. Reset should be controlled so that the counter begins from a defined state after power-up.
সুপারিশকৃত
Frequency Divider
The CD4060BCM is appropriate for a fixed frequency-divider circuit because its 14 ripple-carry stages advance on each negative clock transition and expose multiple binary outputs. A designer can select an appropriate output stage to obtain the required division relationship while avoiding the overhead of a programmable digital timer. The key performance checks are maximum input frequency, propagation delay, output rise and fall time, and the capacitive load presented by downstream logic. Keep clock traces short and use Schmitt-triggered interfacing where an external signal crosses significant noise or slow-edge conditions.
সুপারিশকৃত
Industrial Pulse Counter
The CD4060BCM can serve as the timing backbone of an industrial pulse counter by counting negative clock transitions and presenting a 14-bit binary state. Its listed -55°C to +125°C operating range supports operation across demanding industrial temperature conditions when the complete circuit meets the applicable supply and timing requirements. Use an input conditioning stage for noisy or slow edges, and treat the binary outputs as a ripple-derived word when downstream circuitry samples multiple stages at once. Reset and isolation logic should establish clear startup and fault-recovery behavior.
সুপারিশকৃত
Periodic Event Generator
The CD4060BCM is well suited to periodic event generation because a selected counter stage can produce a divided clock from an internal oscillator or external source. That divided signal can trigger sampling, relay sequencing, flashing indicators, or a downstream actuator at a predictable interval. Component tolerances and temperature drift determine the achievable timing accuracy, so select external timing parts according to the manufacturer oscillator guidance. At the output, pulse shaping may be required because ripple timing and finite transition times influence when a downstream device recognizes each event.
সুপারিশকৃত
Clocked Sequencing System
The CD4060BCM can provide the binary count state for clocked sequencing in legacy control and instrumentation systems. Each negative-edge clock transition advances the state, allowing external decode logic to select one of several timing phases or steps. Its fixed hardware sequence is useful when firmware overhead is undesirable and the operation can be predetermined. Designers should account for the ripple nature of the counter, add reset qualification to avoid metastable startup behavior, and ensure each decoded output remains stable long enough for the connected logic to respond.
সুপারিশকৃত
Oscillator-Based Timebase
The CD4060BCM can serve as an oscillator-based timebase when external timing components establish the operating frequency and the counter provides selectable divided outputs. This arrangement is useful in low-cost timers, sampling clocks, and repetitive control systems that require more than a free-running oscillator but do not need programmable arithmetic. The oscillator's starting behavior, frequency range, and component tolerances should be checked against the manufacturer datasheet. For stable production timing, account for component temperature coefficients and provide generous margins around the intended output frequency.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা CD4060BCM — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | CD4060BMG4 | CD4060BCMX | CD4060BMT | CD4060B |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | Fairchild Semiconductor | Texas Instruments | Texas Instruments |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC orderable suffix required |
| Counter Type | 14-stage ripple-carry binary counter | CD4060B binary counter/divider | CD4060B binary counter/divider | CD4060B binary counter/divider | 14-stage ripple-carry binary counter/divider |
| Counter Resolution | 14 bits | 14 bits | 14 bits | 14 bits | 14 bits |
| Clock Edge | Negative edge | Negative edge | Negative edge | Negative edge | Negative edge |
| Logic Family | 4000-series CMOS | 4000-series CMOS | 4000-series CMOS | 4000-series CMOS | 4000-series CMOS |
| Maximum Supply Voltage | 15 V | 15 V | 15 V | 15 V | 15 V |
মূল পার্থক্যসমূহ
- Combines fixed binary counting and oscillator capability (বনামSN74LS93DR)
- Provides 14 counter stages rather than a 4-bit counting width (বনামSN74LS93DR)
- Single-package timing and division (বনামSN74LS90DR)
ডিজাইন নোট
Assign all 16 nets directly from the manufacturer pin-description table and preserve the standard SOIC pin-one orientation. Place the supply bypass capacitor close to the device power and ground pins, and provide a low-impedance ground path. Keep oscillator components and their associated tracks physically close to the IC to reduce stray capacitance and susceptibility to unrelated circuit noise.
The CD4060BCM advances on the negative clock transition, so confirm that the input waveform crosses the valid threshold cleanly and that reset is released outside the active clock transition region. Use adequate clock rise and fall times, avoid excessive loading on the oscillator node, and do not treat a multi-bit ripple output as simultaneous unless the application tolerates propagation skew across the 14 stages.
Do not select a replacement solely from the CD4060 family name. Verify the exact manufacturer part number, 16-pin SOIC footprint, temperature grade, supply-voltage rating, clock frequency, oscillator range, and lifecycle status. Cross-reference information indicates consistent terminals and functionality for the listed alternatives, but qualification still requires comparison of the ordered suffix and manufacturer electrical limits.
কমপ্লায়েন্স তথ্য
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact CD4060BCM ordering configuration. AEC-Q100 status is treated as not applicable because this is a general-purpose CMOS logic counter rather than an automotive-qualified device.