LM2904VQDR - Dual 30V 700kHz Op Amp | Texas Instruments
MPN: LM2904VQDR ✓ সক্রিয়LM2904VQDR সারাংশ
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. Its place in the signal-chain hierarchy is amplifier IC → operational amplifier → analog signal-conditioning IC → semiconductor. A differential input stage, high open-loop gain, and internally compensated design allow the device to form stable closed-loop gain stages with external resistors or capacitors.
Key features include two amplifier circuits per package, a 700 kHz gain-bandwidth product, and a maximum supply rating of 30 V. The bipolar architecture supports conventional general-purpose applications using single or split supplies. An 8-pin SOIC body measures 0.154 inches wide and 3.90 mm in body width. The manufacturer identifies the LM2904V family as an enhanced alternative to the original LM2904, with operation extending to 125 °C.
The 700 kHz gain-bandwidth product makes the amplifier suitable for low-frequency instrumentation and feedback-control loops rather than high-speed signal chains. Because both channels share one package, grounding and supply-decoupling practices apply to the complete device, and unused channels should be configured according to the manufacturer's recommended stable-input circuit.
Typical uses include industrial sensor interfaces, audio preamplifier stages, current-to-voltage converters, active filters, and power-supply feedback loops. The wide operating range also supports automotive and rugged industrial equipment when the board design, external components, and qualification requirements meet the application specification.
A key design consideration is common-mode and output-swing headroom. Review the input common-mode range and output voltage limits in the manufacturer datasheet for the chosen supply voltage. Decouple each supply pin locally, route feedback connections away from high-current switching nodes, and verify stability with the exact source and load impedances used in production.
This page combines the LM2904VQDR family specifications, package information, pin-compatible alternatives, application guidance, and design notes to help engineers qualify the amplifier and plan a board-level replacement without relying on a single parameter listing.
এর জন্য ড্রপ-ইন বিকল্প LM2904VQDR — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible LM2904VQDR (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Operating Temperature Range, Maximum Supply Voltage, Amplifier Type, Slew Rate.
LM2904VQD
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LM2904BIDR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2904BAIDR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2904AVQDRG4
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2904M/NOPB
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2904YDT
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2904VQDR সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | General-Purpose Operational Amplifier |
| Number of Channels | 2 channels |
| Architecture | Bipolar voltage-feedback |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 700 kHz |
| অপারেটিং তাপমাত্রার পরিসর | -40 °C to 125 °C |
| Package Type | 8-pin SOIC |
| Package Width | 0.154 in (3.90 mm) |
| মাউন্টিং টাইপ | Surface Mount |
| লাইফসাইকেল স্ট্যাটাস | Active |
| Lead-Free Status | Yes |
| MSL | MSL 1 |
| Maximum Reflow Temperature | 260 °C |
| RoHS Compliance | Yes |
| REACH Compliance | Compliant |
LM2904VQDR 0.154 in (3.90 mm) পিন কনফিগারেশন গাইড
LM2904VQDR (0.154 in (3.90 mm) প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি LM2904VQDR.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
LM2904VQDR এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Signal Conditioning, Audio Preamplifier Stage, Current-to-Voltage Conversion, Active Filtering and Control Loops, Automotive and Rugged Control Electronics, Power-Supply Feedback Monitoring.
Industrial Sensor Signal Conditioning
The LM2904VQDR is appropriate for amplifying low-level sensor signals where two channels are needed for differential measurement and buffer functions. Its 30 V supply rating provides headroom for industrial rails, while operation from -40 °C to 125 °C supports temperature-controlled equipment. Configure the amplifier in a noise-gain configuration and confirm that the sensor output remains inside the input common-mode range. The 700 kHz gain-bandwidth product is well suited to temperature, pressure, and position sensors with moderate bandwidth. Keep the feedback resistors close to the amplifier pins, use short ground returns, and place supply-bypass capacitors at the package to reduce noise pickup.
সুপারিশকৃত
Audio Preamplifier Stage
The LM2904VQDR can form a general-purpose audio preamplifier stage when the signal path does not require the bandwidth or low-noise performance of a dedicated audio amplifier. One channel can amplify the incoming program signal, and the second can provide gain or buffering in a balanced or auxiliary path. The device's dual bipolar architecture and 8-pin SOIC footprint simplify board partitioning. At the 700 kHz gain-bandwidth product, closed-loop gains must remain low enough to preserve usable bandwidth. Check output swing at the selected supply and keep the input network referenced to a defined bias when the circuit operates from a single supply.
সুপারিশকৃত
Current-to-Voltage Conversion
The LM2904VQDR is suitable for a shunt-based current measurement when the shunt voltage stays within the amplifier's input common-mode range. Its bipolar input stage is useful around a zero-volt reference, and the 700 kHz gain-bandwidth product supports moderate-speed feedback networks. The principal accuracy limits are input offset voltage, input bias current, feedback-resistor tolerance, and shunt tolerance. Confirm the maximum shunt signal at the highest current and verify that the output remains within the output-swing limits. A dedicated instrumentation amplifier may be preferable when very low offset or high common-mode rejection is required.
সুপারিশকৃত
Active Filtering and Control Loops
The LM2904VQDR can implement active filters, integrators, and low-frequency feedback-control loops where 700 kHz of gain-bandwidth product is adequate for the intended closed-loop bandwidth. Two independent channels allow a filter stage to be followed by an output amplifier within one package. Select resistor and capacitor values against the datasheet's recommended operating range and verify stability with the actual load. Keep the summing node and feedback components physically compact to minimize parasitic capacitance and phase error. When driving a capacitive or long cable load, add an isolation resistor close to the output to reduce oscillation risk.
সুপারিশকৃত
Automotive and Rugged Control Electronics
The LM2904VQDR is suited to control and conditioning electronics operating across -40 °C to 125 °C when the complete design satisfies its automotive application requirements. Its 30 V maximum supply rating supports headroom above a 12 V or 24 V automotive rail after accounting for transients and regulation margin. The dual amplifier can condition a feedback signal and monitor an actuator in one package. Place a local bypass capacitor on the supply pin, maintain a low-impedance ground return, and follow the manufacturer's guidance for unused channels. Automotive qualification also depends on the specific orderable device, change-control requirements, and the complete production test process.
সুপারিশকৃত
Power-Supply Feedback Monitoring
The LM2904VQDR can amplify the error signal or sensed output of an analog power-control loop. Its wide supply capability and dual-channel configuration permit one channel to monitor a regulated rail while the second provides conditioning or a comparator-style reference function. The 700 kHz gain-bandwidth product is suitable for slow feedback loops rather than high-frequency compensation designs. Confirm the maximum input and output voltages, including any transient excursions, and keep the feedback trace away from power-switching nodes. For designs requiring dedicated undervoltage or overvoltage protection with a defined response time, choose a supervisor rather than a general-purpose amplifier.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM2904VQDR — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | LM2904VQD | LM2904BIDR | LM2904BAIDR | LM2904AVQDR | LM2904M/NOPB |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Package | 8-pin SOIC | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
মূল পার্থক্যসমূহ
- Wide operating temperature range (বনামLM2904M/NOPB)
- Consistent 700 kHz gain-bandwidth product within the LM2904V family (বনামLM2904M/NOPB)
- Dual amplifier in a standard 8-pin SOIC footprint (বনামLM2904YDT)
- Active lifecycle family with 30 V supply capability (বনামLM2904M/NOPB)
ডিজাইন নোট
Place the supply-bypass capacitor immediately across the amplifier's supply and ground pins, with a short and low-impedance connection to the ground plane. Route the non-inverting and inverting inputs away from switching nodes, clocks, and high-current return paths. Because both amplifier channels share one package, each channel should have independent local feedback components and its own short feedback route to minimize channel-to-channel coupling.
Do not treat the 30 V supply rating as the permissible input or output voltage. Verify the input common-mode range, output swing, and maximum differential input voltage for the selected supply in the manufacturer datasheet. When using a single supply, provide a bias reference inside the usable common-mode range, and configure an unused channel according to the manufacturer's stable-input recommendations instead of leaving its inputs floating.
The 700 kHz gain-bandwidth product requires closed-loop gain and feedback capacitance to be selected together. Check the gain-bandwidth and phase-margin guidance before using high noise gain. For capacitive or long-line loads, place a small isolation resistor directly at the output and keep the external feedback network compact. Validate stability at the minimum supply voltage, maximum temperature, and highest intended output load.
The 30 V capability does not guarantee low power dissipation in every circuit. Estimated: power dissipation is approximately (VS times quiescent current) plus (VS minus VOUT) times output current, excluding load-related losses. Use the datasheet quiescent-current and output-current limits for the selected grade, then calculate junction temperature with the SOIC thermal-resistance data for the actual PCB copper area.
কমপ্লায়েন্স তথ্য
RoHS, Pb-free, REACH, MSL 1, and 260 °C reflow information are stated for the LM2904 family. AEC-Q100 status and halogen-free status are not explicitly stated for this orderable part.