LM2904VQDR - Dual 30V 700kHz Op Amp | Texas Instruments
MPN: LM2904VQDR ✓ 啟用中LM2904VQDR 概覽
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. Its place in the signal-chain hierarchy is amplifier IC → operational amplifier → analog signal-conditioning IC → semiconductor. A differential input stage, high open-loop gain, and internally compensated design allow the device to form stable closed-loop gain stages with external resistors or capacitors.
Key features include two amplifier circuits per package, a 700 kHz gain-bandwidth product, and a maximum supply rating of 30 V. The bipolar architecture supports conventional general-purpose applications using single or split supplies. An 8-pin SOIC body measures 0.154 inches wide and 3.90 mm in body width. The manufacturer identifies the LM2904V family as an enhanced alternative to the original LM2904, with operation extending to 125 °C.
The 700 kHz gain-bandwidth product makes the amplifier suitable for low-frequency instrumentation and feedback-control loops rather than high-speed signal chains. Because both channels share one package, grounding and supply-decoupling practices apply to the complete device, and unused channels should be configured according to the manufacturer's recommended stable-input circuit.
Typical uses include industrial sensor interfaces, audio preamplifier stages, current-to-voltage converters, active filters, and power-supply feedback loops. The wide operating range also supports automotive and rugged industrial equipment when the board design, external components, and qualification requirements meet the application specification.
A key design consideration is common-mode and output-swing headroom. Review the input common-mode range and output voltage limits in the manufacturer datasheet for the chosen supply voltage. Decouple each supply pin locally, route feedback connections away from high-current switching nodes, and verify stability with the exact source and load impedances used in production.
This page combines the LM2904VQDR family specifications, package information, pin-compatible alternatives, application guidance, and design notes to help engineers qualify the amplifier and plan a board-level replacement without relying on a single parameter listing.
直接替換替代品,適用於 LM2904VQDR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2904VQDR (相同外形與佔位) — 差異在於 Package, Operating Temperature Range, Maximum Supply Voltage, Amplifier Type, Slew Rate.
LM2904VQD
✅ 直接替換📋 參考替代品(不在目錄中)
LM2904BIDR
✅ 直接替換聯絡詢價
查看資料表 →LM2904BAIDR
✅ 直接替換聯絡詢價
查看資料表 →LM2904AVQDRG4
✅ 直接替換聯絡詢價
查看資料表 →LM2904M/NOPB
✅ 直接替換聯絡詢價
查看資料表 →LM2904VQDR 最大額定值與電氣特性
| Amplifier Type | General-Purpose Operational Amplifier |
| Number of Channels | 2 channels |
| Architecture | Bipolar voltage-feedback |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 700 kHz |
| 工作溫度範圍 | -40 °C to 125 °C |
| Package Type | 8-pin SOIC |
| Package Width | 0.154 in (3.90 mm) |
| 安裝類型 | Surface Mount |
| 生命週期狀態 | Active |
| Lead-Free Status | Yes |
| MSL | MSL 1 |
| Maximum Reflow Temperature | 260 °C |
| RoHS Compliance | Yes |
| REACH Compliance | Compliant |
LM2904VQDR 0.154 in (3.90 mm) 腳位配置指南
LM2904VQDR(0.154 in (3.90 mm) 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2904VQDR.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2904VQDR 適用於 6 應用s: Industrial Sensor Signal Conditioning, Audio Preamplifier Stage, Current-to-Voltage Conversion, Active Filtering and Control Loops, Automotive and Rugged Control Electronics, Power-Supply Feedback Monitoring.
Industrial Sensor Signal Conditioning
The LM2904VQDR is appropriate for amplifying low-level sensor signals where two channels are needed for differential measurement and buffer functions. Its 30 V supply rating provides headroom for industrial rails, while operation from -40 °C to 125 °C supports temperature-controlled equipment. Configure the amplifier in a noise-gain configuration and confirm that the sensor output remains inside the input common-mode range. The 700 kHz gain-bandwidth product is well suited to temperature, pressure, and position sensors with moderate bandwidth. Keep the feedback resistors close to the amplifier pins, use short ground returns, and place supply-bypass capacitors at the package to reduce noise pickup.
推薦
Audio Preamplifier Stage
The LM2904VQDR can form a general-purpose audio preamplifier stage when the signal path does not require the bandwidth or low-noise performance of a dedicated audio amplifier. One channel can amplify the incoming program signal, and the second can provide gain or buffering in a balanced or auxiliary path. The device's dual bipolar architecture and 8-pin SOIC footprint simplify board partitioning. At the 700 kHz gain-bandwidth product, closed-loop gains must remain low enough to preserve usable bandwidth. Check output swing at the selected supply and keep the input network referenced to a defined bias when the circuit operates from a single supply.
推薦
Current-to-Voltage Conversion
The LM2904VQDR is suitable for a shunt-based current measurement when the shunt voltage stays within the amplifier's input common-mode range. Its bipolar input stage is useful around a zero-volt reference, and the 700 kHz gain-bandwidth product supports moderate-speed feedback networks. The principal accuracy limits are input offset voltage, input bias current, feedback-resistor tolerance, and shunt tolerance. Confirm the maximum shunt signal at the highest current and verify that the output remains within the output-swing limits. A dedicated instrumentation amplifier may be preferable when very low offset or high common-mode rejection is required.
推薦
Active Filtering and Control Loops
The LM2904VQDR can implement active filters, integrators, and low-frequency feedback-control loops where 700 kHz of gain-bandwidth product is adequate for the intended closed-loop bandwidth. Two independent channels allow a filter stage to be followed by an output amplifier within one package. Select resistor and capacitor values against the datasheet's recommended operating range and verify stability with the actual load. Keep the summing node and feedback components physically compact to minimize parasitic capacitance and phase error. When driving a capacitive or long cable load, add an isolation resistor close to the output to reduce oscillation risk.
推薦
Automotive and Rugged Control Electronics
The LM2904VQDR is suited to control and conditioning electronics operating across -40 °C to 125 °C when the complete design satisfies its automotive application requirements. Its 30 V maximum supply rating supports headroom above a 12 V or 24 V automotive rail after accounting for transients and regulation margin. The dual amplifier can condition a feedback signal and monitor an actuator in one package. Place a local bypass capacitor on the supply pin, maintain a low-impedance ground return, and follow the manufacturer's guidance for unused channels. Automotive qualification also depends on the specific orderable device, change-control requirements, and the complete production test process.
推薦
Power-Supply Feedback Monitoring
The LM2904VQDR can amplify the error signal or sensed output of an analog power-control loop. Its wide supply capability and dual-channel configuration permit one channel to monitor a regulated rail while the second provides conditioning or a comparator-style reference function. The 700 kHz gain-bandwidth product is suitable for slow feedback loops rather than high-frequency compensation designs. Confirm the maximum input and output voltages, including any transient excursions, and keep the feedback trace away from power-switching nodes. For designs requiring dedicated undervoltage or overvoltage protection with a defined response time, choose a supervisor rather than a general-purpose amplifier.
推薦
推薦產品摘要
工程參考資料,適用於 LM2904VQDR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2904VQD | LM2904BIDR | LM2904BAIDR | LM2904AVQDR | LM2904M/NOPB |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Package | 8-pin SOIC | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
主要差異化特點
- Wide operating temperature range (對比LM2904M/NOPB)
- Consistent 700 kHz gain-bandwidth product within the LM2904V family (對比LM2904M/NOPB)
- Dual amplifier in a standard 8-pin SOIC footprint (對比LM2904YDT)
- Active lifecycle family with 30 V supply capability (對比LM2904M/NOPB)
設計說明
Place the supply-bypass capacitor immediately across the amplifier's supply and ground pins, with a short and low-impedance connection to the ground plane. Route the non-inverting and inverting inputs away from switching nodes, clocks, and high-current return paths. Because both amplifier channels share one package, each channel should have independent local feedback components and its own short feedback route to minimize channel-to-channel coupling.
Do not treat the 30 V supply rating as the permissible input or output voltage. Verify the input common-mode range, output swing, and maximum differential input voltage for the selected supply in the manufacturer datasheet. When using a single supply, provide a bias reference inside the usable common-mode range, and configure an unused channel according to the manufacturer's stable-input recommendations instead of leaving its inputs floating.
The 700 kHz gain-bandwidth product requires closed-loop gain and feedback capacitance to be selected together. Check the gain-bandwidth and phase-margin guidance before using high noise gain. For capacitive or long-line loads, place a small isolation resistor directly at the output and keep the external feedback network compact. Validate stability at the minimum supply voltage, maximum temperature, and highest intended output load.
The 30 V capability does not guarantee low power dissipation in every circuit. Estimated: power dissipation is approximately (VS times quiescent current) plus (VS minus VOUT) times output current, excluding load-related losses. Use the datasheet quiescent-current and output-current limits for the selected grade, then calculate junction temperature with the SOIC thermal-resistance data for the actual PCB copper area.
合規資訊
RoHS, Pb-free, REACH, MSL 1, and 260 °C reflow information are stated for the LM2904 family. AEC-Q100 status and halogen-free status are not explicitly stated for this orderable part.