LM358AWST - Dual Low-Power Op Amp | STMicroelectronics
MPN: LM358AWST ✓ সক্রিয়LM358AWST সারাংশ
An operational amplifier is an active semiconductor device that amplifies the voltage difference between its inverting and non-inverting inputs. The LM358 family belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, comparators, and analog signal-chain ICs. Its dual architecture provides two amplifiers in one package, reducing board area while simplifying common power-supply and grounding arrangements.
The LM358AWST is specifically identified as a standard, general-purpose amplifier with two circuits. That makes it useful for functions such as voltage buffering, current-to-voltage conversion, sensor conditioning, differential amplification, and basic active filtering. Because it contains two amplifier sections, one package can support two related analog channels or two stages of a larger signal-processing circuit.
Its MiniSO-8 form factor supports compact surface-mount PCB construction while exposing two complete amplifier channels. The exposed package area of the MiniSO family also provides a thermal path to the PCB, although actual heat dissipation depends on copper area, adjacent components, ambient temperature, and output drive. Designers should preserve the manufacturer’s recommended pad and land-pattern dimensions rather than treating it as a generic SOIC footprint.
Typical uses include industrial sensor interfaces, buffered control signals, low-frequency analog measurement paths, audio preamplifier stages, power-supply monitoring, and general-purpose gain stages. In each case, input common-mode range, output swing, unity-gain stability, noise, and supply requirements must be checked against the circuit’s operating conditions. The LM358AWST is especially relevant where two general-purpose channels are needed without allocating separate single amplifier packages.
For a new layout, route input and output traces away from switching nodes and high-current return paths, connect decoupling capacitors close to the supply pins, and verify the complete analog signal range at worst-case supply voltage and temperature. If the PCB revision is fixed, use the pin-description table and land-pattern drawing in the manufacturer datasheet to confirm every connection before substitution or sourcing an equivalent.
এর জন্য ড্রপ-ইন বিকল্প LM358AWST — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
LM358WST
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LM358YDT
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LM358AWST সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| Number of Amplifiers per Package | 2 amplifiers |
| Power Class | Low power |
| Package Type | 8-pin MiniSO |
| Total Pin Count | 8 pins |
| মাউন্টিং টাইপ | Surface mount |
LM358AWST পিন কনফিগারেশন
| পিন 1 | OUT1 — Output of amplifier channel 1 |
| পিন 2 | IN1- — Inverting input of amplifier channel 1 |
| পিন 3 | IN1+ — Non-inverting input of amplifier channel 1 |
| পিন 4 | GND — Device ground |
| পিন 5 | IN2+ — Non-inverting input of amplifier channel 2 |
| পিন 6 | IN2- — Inverting input of amplifier channel 2 |
| পিন 7 | OUT2 — Output of amplifier channel 2 |
| পিন 8 | VCC — Positive supply connection |
সাধারণ ব্যবহার
LM358AWST এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Conditioning, Audio Preamplifier Stages, Buffered Power-Supply Monitoring, Active Filter and Control Loops, Current-to-Voltage Conversion, Portable and Edge-Device Signal Conditioning.
Industrial Sensor Conditioning
LM358AWST fits two-channel industrial sensor conditioning when the sensor outputs remain within the amplifier’s specified input common-mode range. One channel can amplify or buffer a low-level sensor signal while the second channel can provide offset correction, gain, or an active filter. The dual 8-pin MiniSO package reduces board area and shares supply routing, but the design must verify input bias current, offset voltage, output swing, noise, and stability at the actual 5 V or other operating supply. Decoupling capacitors should be placed close to the supply and ground pins, and sensitive input traces should remain away from switching nodes and motor-return paths.
সুপারিশকৃত
Audio Preamplifier Stages
The LM358AWST can provide two general-purpose low-frequency preamplifier stages for microphone, line-level, or instrument signals. Its dual architecture allows a balanced or multi-stage layout without using two separate packages, while the MiniSO-8 footprint supports compact analog boards. Because the device is not characterized in the confirmed material as a low-noise audio-specific amplifier, noise and distortion must be checked against the signal budget before use. Stable feedback resistors, adequate bypassing, controlled return paths, and verification of output headroom are essential when processing small signals with limited supply voltage.
সুপারিশকৃত
Buffered Power-Supply Monitoring
LM358AWST is suitable for buffering two power-supply or rail-monitoring signals when the monitored voltages fit the specified input common-mode range. One channel may follow a midpoint generated by a resistor divider, while the other can buffer a temperature, current-sense, or fault signal for an analog controller. The 8-pin MiniSO package provides a compact implementation, and both channels operate from the same package supply. Designers should check input bias effects on high-impedance dividers, ensure the output does not approach its swing limits, and provide local supply bypassing to prevent switching or load-transient noise from affecting the monitored signals.
সুপারিশকৃত
Active Filter and Control Loops
LM358AWST can implement two active-filter or control-loop sections when its frequency response and stability characteristics suit the intended gain and phase margin. The dual circuit provides independent channels for cascaded filtering, proportional control, or error amplification in a compact 8-pin MiniSO package. Component tolerances directly influence cutoff frequency and closed-loop behavior, so R-2R networks should use suitable resistor accuracy and stability. The implementation should also account for output loading, supply variation, input transient limits, and the distinction between unity-gain stability and operation with noise gain above one.
সুপারিশকৃত
Current-to-Voltage Conversion
LM358AWST can implement a transimpedance stage for a photodiode, sensor, or precision resistor-based current measurement. One channel provides the inversion and current-to-voltage conversion, while the second can add gain, offset correction, or a test point. The MiniSO-8 package helps minimize board area, but feedback impedance and stray capacitance strongly influence bandwidth and stability. Use the manufacturer’s stability and noise information to select the feedback network, place the input device close to the amplifier, keep the summing node compact, and verify compliance voltage and output swing under the largest expected current.
সুপারিশকৃত
Portable and Edge-Device Signal Conditioning
LM358AWST is appropriate for compact portable or edge devices that need two general-purpose analog channels beside a digital controller. It can buffer sensor inputs, scale ADC driver signals, or condition control feedback while occupying only one 8-pin MiniSO package. Low power is explicitly identified as a characteristic of the device, although the actual system-level consumption depends on supply voltage, quiescent current, channel activity, load, and operating temperature. Keep the analog supply clean, use the smallest practical input-node capacitance, and validate input and output ranges across battery conditions and startup transients.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM358AWST — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | LM358WST | LM358YDT |
|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | MiniSO-8 | MiniSO-8 | MiniSO-8 |
| Amplifier Circuits | 2 circuits | 2 circuits | 2 circuits |
| Total Pins | 8 pins | 8 pins | 8 pins |
| Product Class | General-purpose low-power operational amplifier | General-purpose low-power operational amplifier | General-purpose low-power operational amplifier |
মূল পার্থক্যসমূহ
- Two general-purpose amplifier channels in one compact package (বনামLM358WST)
- Same MiniSO-8 footprint family with a clear ordering-suffix decision (বনামLM358YDT)
- Compact dual-channel implementation (বনামLM324KNSR)
ডিজাইন নোট
Use the STMicroelectronics MiniSO-8 land pattern rather than a generic SOIC-8 footprint. Place the supply-bypass capacitor close to the device supply and ground pins, keep the exposed thermal pad electrically connected as specified, and route sensitive input nets away from switching inductors, power MOSFETs, and high-current return paths. Verify pin 1 orientation against the package marking and PCB assembly documentation before fabrication.
Do not assume that every LM358-family ordering code is electrically or thermally interchangeable. Check the exact suffix against the standalone datasheet for supply limits, input common-mode range, output swing, offset voltage, input bias current, temperature grade, and qualification status. When replacing LM358AWST, compare the candidate’s MiniSO-8 footprint and pin map as well as its electrical characteristics; the family name alone does not establish drop-in qualification.
For sensor or high-impedance input stages, keep the summing node and feedback components compact, minimize parasitic capacitance, and avoid routing inputs beside digital clocks or switching-regulator traces. Confirm that the selected noise gain provides adequate stability with the actual source impedance and load. Include output loading, startup, and supply-transient checks because the common-mode and swing limits determine whether the signal remains linear over the full operating range.
Although LM358AWST is identified as a low-power device, package temperature still depends on supply voltage, quiescent current, output load, ambient temperature, and PCB copper. The MiniSO thermal pad should be connected and laid out according to the manufacturer land pattern. Check worst-case dissipation across temperature and supply tolerance, and preserve copper area where possible so the package can dissipate heat without raising the amplifier’s junction temperature above its specified limit.
কমপ্লায়েন্স তথ্য
Compliance status must be confirmed from the manufacturer product documentation and current material-declaration records for the exact ordering code.