LM393AMX - Dual Differential Comparator 36V SOIC-8 | onsemi
MPN: LM393AMX ✓ সক্রিয়LM393AMX সারাংশ
A voltage comparator is an analog integrated circuit that compares two input voltages and drives its output to indicate which input is higher. Comparators form the sensing layer of the signal-chain hierarchy: they sit between sensors or dividers and digital logic, translating analog thresholds into logic-level decisions. The LM393 family, originally introduced by Fairchild Semiconductor and now manufactured by onsemi, remains the industry-standard general-purpose dual comparator.
Key features include comparison of voltages near ground potential thanks to an input common-mode range that extends to the negative rail, open-collector outputs compatible with all forms of logic (TTL, CMOS, RTL, DTL, MOS), and low current drain of 800 uA typ that suits battery-powered designs. The dual-channel integration lets one comparator monitor a threshold while the second implements hysteresis or a second independent trip point.
Architecturally, the LM393AMX uses a PNP differential input stage that allows common-mode input voltages down to ground on a single supply. The uncommitted open-collector output stage requires an external pull-up resistor, which lets the designer set the output logic level to 5V, 3.3V, or any rail up to the supply maximum, simplifying interfacing with mixed-logic systems. The part is specified across the industrial temperature range, and the A-suffix denotes an enhanced-specification grade over the base LM393.
Typical applications include threshold detection and limit monitors, zero-crossing detectors in power conversion, oscillator and relaxation-clock generation, level shifting between logic families, sensor interfacing with photodiodes or thermistors, and over-voltage/under-voltage supervision on 24V industrial buses.
When designing with this device, remember that open-collector outputs need a pull-up resistor and that small hysteresis (a few millivolts via positive feedback) prevents output chatter on slowly moving inputs near the threshold.
This page synthesizes distributor sourcing information, verified drop-in alternatives with package and parameter matching, and practical design notes not found in the manufacturer datasheet.
এর জন্য ড্রপ-ইন বিকল্প LM393AMX — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible LM393AMX (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Common-Mode Input Range, Response Time, Output Type, Comparator Type.
LM393AM
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM393DR2G
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM393M
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM393AD
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM393DR
✅ ড্রপ-ইন✓ স্টকে আছে
$0.11 / ইউনিট
ডেটাশিট দেখুন →LM393B
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LM393AMX সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 |
| Supply Voltage (Single) | 2 V to 36 V |
| Supply Voltage (Dual) | ±1 V to ±18 V |
| Supply Current (Typ) | 800 uA |
| আউটপুট টাইপ | Open collector |
| Input Common-Mode Range | Includes ground (V-) |
| Logic Compatibility | TTL, CMOS, RTL, DTL, MOS |
| প্যাকেজ | 8-SOIC (3.90 mm width) |
| মাউন্টিং টাইপ | Surface Mount |
| Packaging | Tape and Reel (TR) |
| Product Series | LM393 (A grade) |
| Manufacturer | onsemi (originally Fairchild Semiconductor) |
LM393AMX পিন কনফিগারেশন
| পিন 1 | OUT A — Comparator A output (open collector) |
| পিন 2 | IN A- — Comparator A inverting input |
| পিন 3 | IN A+ — Comparator A non-inverting input |
| পিন 4 | GND / V- — Ground or negative supply |
| পিন 5 | IN B+ — Comparator B non-inverting input |
| পিন 6 | IN B- — Comparator B inverting input |
| পিন 7 | OUT B — Comparator B output (open collector) |
| পিন 8 | VCC / V+ — Positive supply |
সাধারণ ব্যবহার
LM393AMX এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Threshold and Limit Detection, Zero-Crossing Detection in Power Conversion, Relaxation Oscillators and Clock Generation, Sensor Interface and Level Shifting, Battery-Powered and Portable Instrumentation, Industrial Automation and Motor Drive Supervision.
Threshold and Limit Detection
The LM393AMX is the classic choice for comparing a sensor voltage against a reference threshold. Its 2V to 36V single-supply range allows direct connection across industrial 24V buses via a simple resistive divider, while inputs that operate down to ground permit near-zero trip points without negative supplies. The dual channels let one comparator monitor an over-voltage limit while the second watches an under-voltage limit, implementing window supervision in one package. With 800 uA typical supply current, the supervision circuit adds negligible standby drain. Place 10k to 100k pull-up resistors on the open-collector outputs to the logic rail, and add hysteresis via positive feedback so slowly drifting battery or bus voltages do not cause output chatter near the trip point.
সুপারিশকৃত
Zero-Crossing Detection in Power Conversion
In AC mains monitoring, phase-angle control, and switching power supplies, the LM393AMX detects when a rectified sine wave crosses a reference, generating timing edges for triac firing or synchronous switching. The wide 36V supply ceiling allows direct connection to rectified low-voltage AC, and the open-collector output cleanly drives optocoupler LEDs or MCU interrupt pins. The PNP input stage sensing near ground potential is essential here, since the zero-cross point sits at the negative rail. Add a few millivolts of hysteresis to reject mains noise, and keep input resistors sized for the peak voltage so the differential stage stays within its common-mode range throughout the cycle.
সুপারিশকৃত
Relaxation Oscillators and Clock Generation
A single LM393AMX comparator with an RC network and positive feedback forms a low-cost relaxation oscillator for watchdog timing, LED blinking, or clock generation. The 800 uA typical supply current keeps oscillator power minimal, and operation from 2V supports coin-cell designs. Oscillator frequency is set by the RC time constant; with a 100k resistor and 100nF capacitor the period lands in the tens-of-milliseconds range, easily scaled across audio to kilohertz rates. The open-collector output produces rail-to-rail square waves regardless of supply voltage, and the second comparator in the package remains available for an independent function such as a battery-low alarm on the same board.
সুপারিশকৃত
Sensor Interface and Level Shifting
Photodiodes, thermistors, and resistive bridges produce small analog signals that need comparison against thresholds before entering digital logic. The LM393AMX inputs sense voltages near ground, ideal for photodiode current-to-voltage outputs referenced to 0V, while the 36V rating tolerates industrial supply excursions. The open-collector output is the key level-shift asset: pull it to 5V for TTL systems or 3.3V for MCU GPIO, letting a 24V-referenced sensor circuit interface directly to low-voltage logic without additional translation ICs. Use 1% resistors in the reference divider and add an RC filter on the input to suppress sensor noise before comparison.
সুপারিশকৃত
Battery-Powered and Portable Instrumentation
For battery monitors and portable test equipment, the LM393AMX delivers dual-comparator function at 800 uA typical, and its specified operation from 2V single-supply means it keeps working as lithium cells discharge toward end of charge. The dual channels implement battery-low warning and battery-dead cutoff thresholds independently. Open-collector outputs allow the outputs to be OR-wired (wired-AND) for combined alarm signaling without extra gates. For lowest average power, gate the comparator supply with a small P-channel MOSFET and poll the battery state periodically rather than continuously, cutting effective consumption to microamp-level duty-cycled figures.
সুপারিশকৃত
Industrial Automation and Motor Drive Supervision
In factory automation panels and motor drives, the LM393AMX supervises current-sense amplifier outputs against over-current trip levels and monitors DC bus undervoltage. The 36V supply rating directly covers 24V industrial control rails, and the wide input common-mode range handles grounded current-shunt references. Open-collector outputs wire-OR multiple fault signals onto a single active-low fault line to the PLC or drive MCU. Add positive-feedback hysteresis of tens of millivolts to lock the trip behavior against motor PWM ripple, and route the comparator ground return separately from power ground to keep trip accuracy in the millivolt range under high-current switching.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM393AMX — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | LM393AM | LM393DR2G | LM393AD | LM393DR | LM393B |
|---|---|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same |
| Brand | onsemi | onsemi | onsemi | STMicroelectronics | Texas Instruments | Texas Instruments |
| Number of Comparators | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 2 V to 36 V (±1 V to ±18 V) | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2.7 V to 36 V |
| Supply Current (Typ) | 800 uA | 800 uA | 800 uA | 800 uA | 800 uA | 800 uA |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Grade | A grade (enhanced) | A grade | Standard grade | Standard grade | Standard grade | Improved (B) grade |
মূল পার্থক্যসমূহ
- A-grade enhanced specifications (বনামLM393M)
- Wider proven supply range for 24V industrial buses (বনামLM393B)
- Same-brand second-source within onsemi (বনামLM393DR2G)
ডিজাইন নোট
The LM393AMX has open-collector outputs - forgetting the pull-up resistor is the most common first-use error and results in no output signal at all. Fit a 10k pull-up to the logic rail (5V or 3.3V) on each output used. Also, both comparators share the V- (pin 4) supply pin; if only one channel is used, tie the unused inputs to a defined logic level (e.g., both to ground or both to a divider) rather than leaving them floating, which can cause the unused output to oscillate and inject noise into the active channel.
Add hysteresis whenever the input signal moves slowly relative to the comparison decision. Without it, input-referred noise (typically a few millivolts) causes the output to chatter near the threshold, generating spurious interrupts in MCU systems. A positive-feedback resistor from output to the non-inverting input, sized about 100x the source impedance of the divider, gives tens of millivolts of trip window. Calculate the resulting trip-point shift explicitly, since feedback also offsets the nominal threshold by the hysteresis magnitude.
Place a 100nF ceramic decoupling capacitor directly across pins 4 and 8 of the SOIC-8 footprint, with the trace from the capacitor to pin 8 kept under 10mm. When comparing signals referenced to ground on a single supply, connect the input divider ground return to the same node as pin 4 to avoid millivolt-level ground drops shifting the trip point. For inputs routed from high-impedance sources above roughly 10k source impedance, add a small RC filter (e.g., 1k and 1nF) to limit noise pickup on the PCB trace.
কমপ্লায়েন্স তথ্য
Compliance status not stated in the retrieved listings; confirm RoHS/REACH status on the onsemi product page or via the Request a Quote form.