LM393AMX - Dual Differential Comparator 36V SOIC-8 | onsemi
MPN: LM393AMX ✓ Hoạt độngLM393AMX Tóm tắt
A voltage comparator is an analog integrated circuit that compares two input voltages and drives its output to indicate which input is higher. Comparators form the sensing layer of the signal-chain hierarchy: they sit between sensors or dividers and digital logic, translating analog thresholds into logic-level decisions. The LM393 family, originally introduced by Fairchild Semiconductor and now manufactured by onsemi, remains the industry-standard general-purpose dual comparator.
Key features include comparison of voltages near ground potential thanks to an input common-mode range that extends to the negative rail, open-collector outputs compatible with all forms of logic (TTL, CMOS, RTL, DTL, MOS), and low current drain of 800 uA typ that suits battery-powered designs. The dual-channel integration lets one comparator monitor a threshold while the second implements hysteresis or a second independent trip point.
Architecturally, the LM393AMX uses a PNP differential input stage that allows common-mode input voltages down to ground on a single supply. The uncommitted open-collector output stage requires an external pull-up resistor, which lets the designer set the output logic level to 5V, 3.3V, or any rail up to the supply maximum, simplifying interfacing with mixed-logic systems. The part is specified across the industrial temperature range, and the A-suffix denotes an enhanced-specification grade over the base LM393.
Typical applications include threshold detection and limit monitors, zero-crossing detectors in power conversion, oscillator and relaxation-clock generation, level shifting between logic families, sensor interfacing with photodiodes or thermistors, and over-voltage/under-voltage supervision on 24V industrial buses.
When designing with this device, remember that open-collector outputs need a pull-up resistor and that small hysteresis (a few millivolts via positive feedback) prevents output chatter on slowly moving inputs near the threshold.
This page synthesizes distributor sourcing information, verified drop-in alternatives with package and parameter matching, and practical design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho LM393AMX — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM393AMX (cùng hình factor và footprint) — khác nhau ở Package, Common-Mode Input Range, Response Time, Output Type, Comparator Type.
LM393AM
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393DR2G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393M
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393AD
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393DR
✅ Drop-In✓ Còn hàng
$0.11 / Đơn vị
Xem tài liệu →LM393B
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM393AMX Tỷ lệ tối đa & tính chất điện
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 |
| Supply Voltage (Single) | 2 V to 36 V |
| Supply Voltage (Dual) | ±1 V to ±18 V |
| Supply Current (Typ) | 800 uA |
| Kiểu đầu ra | Open collector |
| Input Common-Mode Range | Includes ground (V-) |
| Logic Compatibility | TTL, CMOS, RTL, DTL, MOS |
| Hộp | 8-SOIC (3.90 mm width) |
| Kiểu lắp đặt | Surface Mount |
| Packaging | Tape and Reel (TR) |
| Product Series | LM393 (A grade) |
| Manufacturer | onsemi (originally Fairchild Semiconductor) |
Cấu hình chân LM393AMX
| Chân 1 | OUT A — Comparator A output (open collector) |
| Chân 2 | IN A- — Comparator A inverting input |
| Chân 3 | IN A+ — Comparator A non-inverting input |
| Chân 4 | GND / V- — Ground or negative supply |
| Chân 5 | IN B+ — Comparator B non-inverting input |
| Chân 6 | IN B- — Comparator B inverting input |
| Chân 7 | OUT B — Comparator B output (open collector) |
| Chân 8 | VCC / V+ — Positive supply |
Ứng dụng tiêu biểu
LM393AMX phù hợp cho 6 Áp dụngs: Threshold and Limit Detection, Zero-Crossing Detection in Power Conversion, Relaxation Oscillators and Clock Generation, Sensor Interface and Level Shifting, Battery-Powered and Portable Instrumentation, Industrial Automation and Motor Drive Supervision.
Threshold and Limit Detection
The LM393AMX is the classic choice for comparing a sensor voltage against a reference threshold. Its 2V to 36V single-supply range allows direct connection across industrial 24V buses via a simple resistive divider, while inputs that operate down to ground permit near-zero trip points without negative supplies. The dual channels let one comparator monitor an over-voltage limit while the second watches an under-voltage limit, implementing window supervision in one package. With 800 uA typical supply current, the supervision circuit adds negligible standby drain. Place 10k to 100k pull-up resistors on the open-collector outputs to the logic rail, and add hysteresis via positive feedback so slowly drifting battery or bus voltages do not cause output chatter near the trip point.
Được đề xuất
Zero-Crossing Detection in Power Conversion
In AC mains monitoring, phase-angle control, and switching power supplies, the LM393AMX detects when a rectified sine wave crosses a reference, generating timing edges for triac firing or synchronous switching. The wide 36V supply ceiling allows direct connection to rectified low-voltage AC, and the open-collector output cleanly drives optocoupler LEDs or MCU interrupt pins. The PNP input stage sensing near ground potential is essential here, since the zero-cross point sits at the negative rail. Add a few millivolts of hysteresis to reject mains noise, and keep input resistors sized for the peak voltage so the differential stage stays within its common-mode range throughout the cycle.
Được đề xuất
Relaxation Oscillators and Clock Generation
A single LM393AMX comparator with an RC network and positive feedback forms a low-cost relaxation oscillator for watchdog timing, LED blinking, or clock generation. The 800 uA typical supply current keeps oscillator power minimal, and operation from 2V supports coin-cell designs. Oscillator frequency is set by the RC time constant; with a 100k resistor and 100nF capacitor the period lands in the tens-of-milliseconds range, easily scaled across audio to kilohertz rates. The open-collector output produces rail-to-rail square waves regardless of supply voltage, and the second comparator in the package remains available for an independent function such as a battery-low alarm on the same board.
Được đề xuất
Sensor Interface and Level Shifting
Photodiodes, thermistors, and resistive bridges produce small analog signals that need comparison against thresholds before entering digital logic. The LM393AMX inputs sense voltages near ground, ideal for photodiode current-to-voltage outputs referenced to 0V, while the 36V rating tolerates industrial supply excursions. The open-collector output is the key level-shift asset: pull it to 5V for TTL systems or 3.3V for MCU GPIO, letting a 24V-referenced sensor circuit interface directly to low-voltage logic without additional translation ICs. Use 1% resistors in the reference divider and add an RC filter on the input to suppress sensor noise before comparison.
Được đề xuất
Battery-Powered and Portable Instrumentation
For battery monitors and portable test equipment, the LM393AMX delivers dual-comparator function at 800 uA typical, and its specified operation from 2V single-supply means it keeps working as lithium cells discharge toward end of charge. The dual channels implement battery-low warning and battery-dead cutoff thresholds independently. Open-collector outputs allow the outputs to be OR-wired (wired-AND) for combined alarm signaling without extra gates. For lowest average power, gate the comparator supply with a small P-channel MOSFET and poll the battery state periodically rather than continuously, cutting effective consumption to microamp-level duty-cycled figures.
Được đề xuất
Industrial Automation and Motor Drive Supervision
In factory automation panels and motor drives, the LM393AMX supervises current-sense amplifier outputs against over-current trip levels and monitors DC bus undervoltage. The 36V supply rating directly covers 24V industrial control rails, and the wide input common-mode range handles grounded current-shunt references. Open-collector outputs wire-OR multiple fault signals onto a single active-low fault line to the PLC or drive MCU. Add positive-feedback hysteresis of tens of millivolts to lock the trip behavior against motor PWM ripple, and route the comparator ground return separately from power ground to keep trip accuracy in the millivolt range under high-current switching.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM393AMX — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM393AM | LM393DR2G | LM393AD | LM393DR | LM393B |
|---|---|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same |
| Brand | onsemi | onsemi | onsemi | STMicroelectronics | Texas Instruments | Texas Instruments |
| Number of Comparators | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 2 V to 36 V (±1 V to ±18 V) | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2.7 V to 36 V |
| Supply Current (Typ) | 800 uA | 800 uA | 800 uA | 800 uA | 800 uA | 800 uA |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Grade | A grade (enhanced) | A grade | Standard grade | Standard grade | Standard grade | Improved (B) grade |
Bảo phân biệt quan trọng
- A-grade enhanced specifications (vsLM393M)
- Wider proven supply range for 24V industrial buses (vsLM393B)
- Same-brand second-source within onsemi (vsLM393DR2G)
Ghi chú thiết kế
The LM393AMX has open-collector outputs - forgetting the pull-up resistor is the most common first-use error and results in no output signal at all. Fit a 10k pull-up to the logic rail (5V or 3.3V) on each output used. Also, both comparators share the V- (pin 4) supply pin; if only one channel is used, tie the unused inputs to a defined logic level (e.g., both to ground or both to a divider) rather than leaving them floating, which can cause the unused output to oscillate and inject noise into the active channel.
Add hysteresis whenever the input signal moves slowly relative to the comparison decision. Without it, input-referred noise (typically a few millivolts) causes the output to chatter near the threshold, generating spurious interrupts in MCU systems. A positive-feedback resistor from output to the non-inverting input, sized about 100x the source impedance of the divider, gives tens of millivolts of trip window. Calculate the resulting trip-point shift explicitly, since feedback also offsets the nominal threshold by the hysteresis magnitude.
Place a 100nF ceramic decoupling capacitor directly across pins 4 and 8 of the SOIC-8 footprint, with the trace from the capacitor to pin 8 kept under 10mm. When comparing signals referenced to ground on a single supply, connect the input divider ground return to the same node as pin 4 to avoid millivolt-level ground drops shifting the trip point. For inputs routed from high-impedance sources above roughly 10k source impedance, add a small RC filter (e.g., 1k and 1nF) to limit noise pickup on the PCB trace.
Thông tin tuân thủ
Compliance status not stated in the retrieved listings; confirm RoHS/REACH status on the onsemi product page or via the Request a Quote form.