MAX232EWE+T - 120kbps 5V RS-232 Transceiver | Maxim
MPN: MAX232EWE+T ✓ সক্রিয়MAX232EWE+T সারাংশ
An RS-232 transceiver is an interface IC that converts low-voltage CMOS or TTL logic signals into RS-232 levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the interface IC hierarchy and is commonly placed between a host controller, microcontroller, or data-processing equipment and an external RS-232 port. Unlike a direct TTL connection, the MAX232EWE+T adds voltage-level translation, noise tolerance, and standard-compliant line signaling.
The device supports a 4.5 V to 5.5 V supply range and data rates up to 120 kbps. Its two drivers and two receivers are intended for EIA/TIA-232E, V.28, and V.24 interfaces. The integrated charge-pump circuitry eliminates the need for an external positive supply, while external capacitors provide the voltage multiplication and supply filtering required by the device.
The MAX232 family uses bipolar charge-pump circuitry to translate a 5 V input into approximately positive and negative RS-232 output levels. Receiver inputs are designed to detect the corresponding negative-going RS-232 signals, while the drivers provide the required level shifting and signal conditioning. Because the interface operates through voltage conversion rather than differential signaling, it is intended for point-to-point RS-232 connections rather than long multidrop networks.
Typical uses include serial service ports, industrial control links, configuration interfaces, test equipment, and legacy peripheral connections. Two transmit and two receive channels can support one hardware handshake flow or two independent unidirectional links. The 120 kbps capability also makes the device suitable for moderate-rate data links where legacy RS-232 equipment must interoperate with newer control electronics.
PCB design should place the charge-pump capacitors close to their associated pins and keep the RS-232 connector interface path away from sensitive analog or high-speed digital traces. Protection components may be added at exposed connector pins, but their capacitance and clamping voltage must be checked so they do not impair receiver detection or driver operation.
This product page combines the manufacturer interface specifications with practical PCB guidance, application-oriented design context, and a package-focused comparison. It helps engineers distinguish the wide-SOIC MAX232EWE+T from temperature-grade, packing-code, narrow-SOIC, and functionally similar interface devices that may not be drop-in replacements for an existing layout.
এর জন্য ড্রপ-ইন বিকল্প MAX232EWE+T — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MAX232EWE+T (একই form factor এবং footprint) — পার্থক্য রয়েছে Product Type, Interface Standard, Package.
MAX232CWE+T
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX232EWE-T
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX232CWE+
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX232EWE+T বিশেষণ
| Product Type | RS-232 transceiver interface IC |
| Transmit Channels | 2 drivers |
| Receive Channels | 2 receivers |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 120 kbps |
| Interface Standard | EIA/TIA-232E |
| Additional Standards | CCITT V.28 and V.24 |
| Logic Supply | +5 V |
| প্যাকেজ | 16-pin wide SOIC |
| Package Width | 7.50 mm |
| Package Length | 0.295 inch |
| পিন সংখ্যা | 16 pins |
| মাউন্টিং টাইপ | Surface mount |
MAX232EWE+T 0.295 inch পিন কনফিগারেশন গাইড
MAX232EWE+T (0.295 inch প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX232EWE+T.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MAX232EWE+T এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Controller Serial Port, Legacy Peripheral Configuration, Test and Measurement Equipment, Serial Service and Diagnostics, Embedded Data Acquisition Module, Networking and Router Management Port.
Industrial Controller Serial Port
The MAX232EWE+T is appropriate for an industrial controller that must communicate with legacy RS-232 equipment over a point-to-point cable. Its two driver channels and two receive channels support a full-duplex data path plus hardware handshaking, while operation up to 120 kbps covers typical service-port traffic. The 4.5 V to 5.5 V supply range also matches conventional 5 V logic systems. Place the charge-pump capacitors near the IC and route connector-side traces away from sensitive digital circuitry to reduce coupling. The 16-pin wide-SOIC package provides a practical surface-mount implementation for control boards where connector protection and grounding are handled separately.
সুপারিশকৃত
Legacy Peripheral Configuration
The MAX232EWE+T can connect a modern controller to a legacy peripheral that retains an RS-232 configuration port. The receiver translates incoming negative-going RS-232 levels into logic signals, while the driver converts the controller's logic output into the required line voltage. Two drivers allow separate control and status paths when the peripheral uses RTS and CTS handshaking. The 120 kbps maximum data rate is more than adequate for configuration and diagnostic traffic. Designers should verify logic levels, provide connector-side protection, and observe the manufacturer's recommended capacitor layout to maintain signal timing and charge-pump behavior.
সুপারিশকৃত
Test and Measurement Equipment
The MAX232EWE+T is useful in test equipment that needs to exchange commands and results with a RS-232-controlled instrument. The two receive channels can collect separate status signals, and the two transmit channels can support command output plus flow control. With operation up to 120 kbps, the interface handles short command frames and moderate diagnostic data streams without requiring a higher-speed transceiver. A careful layout should keep the RS-232 traces away from analog inputs and reference circuitry. Grounding and cable transients remain system-level concerns, so connector protection should be selected with suitable capacitance and standoff characteristics.
সুপারিশকৃত
Serial Service and Diagnostics
The MAX232EWE+T supports service consoles, maintenance ports, and diagnostic interfaces that rely on RS-232 rather than USB or Ethernet. The single +5 V supply simplifies implementation in equipment where negative RS-232 voltage generation is otherwise inconvenient. Two drivers and two receivers permit full-duplex messaging and optional hardware handshaking, while the 120 kbps limit suits command-oriented service protocols. Use short, properly referenced connections and place the external charge-pump capacitors directly beside the associated pins. The surface-mount wide-SOIC package also supports automated assembly in production equipment without requiring through-hole interconnects.
সুপারিশকৃত
Embedded Data Acquisition Module
The MAX232EWE+T can provide a robust wired interface between an embedded data-acquisition controller and an external instrument. Its two receive channels support separate data and status lines, and its two driver channels can carry commands and acknowledgments. The 120 kbps rate is suitable for many sensor, laboratory, and process-control links that transfer compact records rather than continuous high-bandwidth streams. Because RS-232 is point-to-point and uses voltage levels referenced to ground, the module should implement suitable cable grounding and connector protection. Decouple the 5 V rail locally and preserve the recommended charge-pump capacitor placement to avoid timing distortion.
সুপারিশকৃত
Networking and Router Management Port
The MAX232EWE+T is applicable to management ports on routers, switches, and network appliances that expose an RS-232 console for configuration or diagnostics. The device supplies the required electrical translation between internal 5 V logic and the RS-232 console connector while supporting two receive paths for console data and hardware flow control. Its 120 kbps capability comfortably covers terminal interaction rates. Board-level implementation should reserve space for connector protection, maintain separation between the port and sensitive Ethernet or power sections, and verify the exact MAX232EWE+T suffix against environmental requirements. This arrangement preserves a conventional administrative interface without requiring a negative external supply.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX232EWE+T — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MAX232CWE+T | MAX232EWE-T | MAX232CWE |
|---|---|---|---|---|
| Package | 16-pin wide SOIC | 16-pin wide SOIC | 16-pin wide SOIC | 16-pin wide SOIC |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Product Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
মূল পার্থক্যসমূহ
- Two-driver, two-receiver interface in one package (বনামMAX232CWE+T)
- 120 kbps maximum signaling rate (বনামMAX232EWE-T)
- Single 5 V supply with integrated level translation (বনামMAX232CWE)
ডিজাইন নোট
Place the MAX232EWE+T charge-pump capacitors and 5 V bypass capacitor close to their associated package pins. Keep the charge-pump capacitor loop compact to reduce radiated noise and maintain clean internal supply generation. Route connector-side RS-232 traces away from clocks, ADC inputs, and precision analog nodes; when separation is impossible, use a grounded guard structure and verify the completed layout with signal-integrity measurements.
Do not assume that a shared SOIC designation guarantees interchangeability. Verify the package width, pin functions, temperature grade, supply limits, and external capacitor requirements for every suffix. In particular, a wide-SOIC MAX232EWE+T must not be placed on a footprint intended for a narrow-SOIC device. Confirm the manufacturer ordering table before approving a substitute in a new or revised PCB layout.
RS-232 is a point-to-point, single-ended interface, so cable routing, grounding, and connector protection influence reliability more than trace geometry at 120 kbps. Select protection devices with capacitance compatible with the receiver and driver timing requirements. Avoid long unterminated stub branches, maintain a consistent ground reference, and test the completed cable assembly for startup glitches and ground-loop-induced noise.
কমপ্লায়েন্স তথ্য
Compliance declarations were not present in the accessible product information. The +T ordering suffix identifies the tape-and-reel delivery configuration and does not by itself establish environmental qualification.