MAX355CWE+ - Dual 4:1 Fault-Protected Analog Mux | Maxim
MPN: MAX355CWE+ ✓ فعالMAX355CWE+ جائزہ
An analog multiplexer is a switching interface that connects one signal source to one of several destinations. In this case, each MAX355CWE+ channel implements a 4:1 configuration, allowing two multiplexers to route four sources per channel. Within the broader semiconductor hierarchy, the MAX355CWE+ is an analog switch IC, then a multiplexer, then an interface IC used to connect external signals to analog processing circuitry.
Key electrical characteristics include a maximum on-resistance of 350 ohms, maximum off leakage of 500 pA, and crosstalk of -92 dB at 100 kHz. The 350 ohm resistance is suitable for moderate-impedance sensor, measurement, and control paths rather than high-bandwidth, low-impedance video networks. Fault protection extends to 40 V beyond the supply rails, helping isolate sensitive downstream circuitry during abnormal input conditions.
The device uses a series N-channel, P-channel, and N-channel switching structure to provide fault protection. Its dual-mux architecture makes it useful where multiple analog inputs must be selected under software or hardware control. Control inputs allow the selected paths to be changed without mechanical switching, making the MAX355CWE+ appropriate for test systems, industrial controls, data acquisition modules, and instrumentation.
Typical uses include battery-powered monitoring equipment, industrial sensor interfaces, laboratory measurement systems, and analog test equipment. The 4.5 V minimum supply supports systems operating from a 5 V rail, while the 36 V maximum expands applicability to higher-voltage industrial environments. Protection is especially relevant where an external cable or sensor may present an overvoltage before system power stabilizes.
Designers should verify the input and output voltage limits against the specific fault condition and avoid treating the 40 V protection rating as a continuous operating rating. Keep analog routing paths away from high-current switching nodes, provide a stable bypass capacitor near the supply pins, and use high-impedance sensing circuits to reduce errors caused by the 350 ohm on-resistance.
This page combines the MAX355CWE+ electrical characteristics, application guidance, package information, and verified drop-in alternatives to support faster component selection and PCB replacement decisions.
کے لیے ڈراپ اِن متبادل MAX355CWE+ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX355CWE+ (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Multiplexer Configuration, On-Resistance, Package.
MAX355CWE
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX355EWE+
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX355CWE+ تفصیلات
| Multiplexer Configuration | Dual 4:1 |
| Number of Circuits | 2 circuits |
| On-Resistance | 350 ohm maximum |
| Supply Voltage Range | 4.5 V to 36 V |
| Overvoltage Protection | Up to 40 V beyond supply rails |
| Off Leakage Current | 500 pA maximum |
| Crosstalk | -92 dB at 100 kHz |
| آپریٹنگ درجہ حرارت | 0°C to 70°C |
| پیکیج | 16-SOIC, 7.50 mm width |
| Package Type | WSOIC-16 |
| ماؤنٹنگ ٹائپ | Surface mount |
| Switch Structure | Series N-channel, P-channel, N-channel |
| Fault Protection | Protected during power-up, power-down, and fault conditions |
| Lead-Free Finish | Yes for MAX355CWE+ ordering suffix |
MAX355CWE+ wsoic-16 پن کنفیگریشن گائیڈ
MAX355CWE+ (wsoic-16 پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX355CWE+.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MAX355CWE+ کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Multiplexing, Data Acquisition Modules, Automated Test Equipment, Battery-Powered Monitoring Equipment, Laboratory Measurement Systems, High-Voltage Control Interfaces.
Industrial Sensor Multiplexing
The MAX355CWE+ fits industrial sensor interfaces that require several measured signals to share a limited analog front end. Each of its two independent 4:1 sections can connect one of four inputs to a common terminal, reducing the number of analog routing components needed. The 4.5 V to 36 V supply range supports both 5 V instrumentation and higher-voltage industrial rails, while protection up to 40 V beyond the supply rails helps manage transient faults. Because on-resistance reaches 350 ohm, the selected sensor impedance and allowable measurement error must be included in the signal-chain design.
تجویز کردہ
Data Acquisition Modules
A dual 4:1 analog multiplexer is useful in compact data-acquisition modules where several inputs must be routed to a shared converter or measurement amplifier. The MAX355CWE+ provides two selectable four-input groups in one 16-WSOIC package, simplifying control logic and conserving board area. Its maximum off leakage of 500 pA and -92 dB crosstalk at 100 kHz help preserve signal integrity between channels, although the 350 ohm switch resistance should be compensated when the source impedance is finite. The 4.5 V minimum supply also supports conventional 5 V acquisition systems.
تجویز کردہ
Automated Test Equipment
The MAX355CWE+ can route test signals among multiple sources in automated test equipment while providing fault isolation during startup or abnormal fixture conditions. Two 4:1 sections allow compact control of several test paths without requiring a separate switch for every channel. The maximum on-resistance of 350 ohm is generally appropriate for high-impedance test fixtures, and the -92 dB crosstalk specification at 100 kHz supports low-level signal measurements. Designers should still account for switch resistance, leakage, and settling time in the measurement accuracy budget.
تجویز کردہ
Battery-Powered Monitoring Equipment
The MAX355CWE+ is suitable for battery-powered monitoring equipment that multiplexes sensor inputs while operating from a regulated 5 V system. Its dual 4:1 organization reduces wiring and component count in portable instruments, and fault protection helps prevent external sensor lines from exposing downstream circuitry to startup or shutdown overvoltage. The 4.5 V minimum supply fits a 5 V rail, while the 350 ohm maximum on-resistance is best matched to high-impedance sensors. Confirm that injected channel error remains acceptable at the lowest expected source impedance.
تجویز کردہ
Laboratory Measurement Systems
Laboratory measurement systems can use the MAX355CWE+ to select among four input paths in each of two switch sections. The -92 dB crosstalk at 100 kHz and 500 pA maximum off leakage help maintain channel separation for precision measurements, while the 4:1 topology supports compact instrument front ends. The 350 ohm on-resistance is the primary accuracy consideration when driving amplifier inputs with finite impedance. Keep the routing traces short, maintain a quiet ground reference, and compare the complete measurement uncertainty against the selected switch resistance.
تجویز کردہ
High-Voltage Control Interfaces
The MAX355CWE+ can interface control signals in systems operating across a broad supply range, including industrial 24 V and 36 V applications. Its 4.5 V to 36 V operating specification supports higher-voltage logic environments, and the fault-protected series N-channel, P-channel, and N-channel structure limits fault exposure beyond the normal rails. When switching external control lines, verify the absolute maximum input and output ratings, ensure the selected switch path does not exceed them, and provide local supply bypassing to maintain stable operation.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX355CWE+ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX355CWE | MAX355EWE+ |
|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| On-Resistance | 350 ohm maximum | 350 ohm maximum | 350 ohm maximum |
| Supply Voltage Range | 4.5 V to 36 V | 4.5 V to 36 V | 4.5 V to 36 V |
| Off Leakage Current | 500 pA maximum | 500 pA maximum | 500 pA maximum |
| Crosstalk | -92 dB at 100 kHz | -92 dB at 100 kHz | -92 dB at 100 kHz |
| Operating Temperature | 0°C to 70°C | 0°C to 70°C | -40°C to 85°C |
| Overvoltage Protection | Up to 40 V beyond supply rails | Up to 40 V beyond supply rails | Up to 40 V beyond supply rails |
اہم امتیازی خصوصیات
- Combines two protected 4:1 multiplexers in one package (بمقابلہMAX355CWE)
- Maintains the same protected analog-switch architecture for exact-family replacement (بمقابلہMAX355EWE+)
- Commercial grade supports a 0°C to 70°C operating range (بمقابلہMAX355EWE+)
ڈیزائن نوٹس
Treat the 350 ohm maximum on-resistance as part of the signal-path impedance rather than as an ideal switch resistance. For a divider formed by this resistance and the receiving input impedance, the resulting error can be significant when the input impedance is only tens of kilohms. Use a high-impedance receiver or amplifier input, and include channel resistance and leakage in the measurement uncertainty calculation.
Place the supply bypass capacitor close to the device supply and ground pins, and keep analog switch traces short and separated from switching-current paths. The dual 4:1 topology can place sensitive signals near control or routed channels, so route the two groups with attention to crosstalk and ground return paths. A continuous ground reference under the device helps reduce coupling into the high-impedance measurement paths.
Do not confuse fault protection with a continuous overvoltage rating. The MAX355 family protects against overvoltage up to 40 V beyond the supply rails during power-up, power-down, and fault conditions, but normal operating voltages and absolute maximum ratings must still be respected. Also confirm the selected control logic and pin functions against the manufacturer datasheet rather than assigning control signals from generic multiplexer conventions.
Reserve the same 16-SOIC land pattern when evaluating MAX355CWE and MAX355EWE+ replacements. Verify body width, lead pitch, and pin orientation on the PCB rather than relying only on the generic package name. The two identified replacements use the same family architecture, but production qualification should still include control-state timing, temperature behavior, and the worst-case analog accuracy at the required source impedance.
تعمیل کی معلومات
The plus suffix identifies the lead-free ordering option. No explicit RoHS, REACH, halogen-free, conflict-minerals, or AEC-Q100 statement was included in the cited product records.