MAX355CWE+ - Dual 4:1 Fault-Protected Analog Mux | Maxim
MPN: MAX355CWE+ ✓ 啟用中MAX355CWE+ 概覽
An analog multiplexer is a switching interface that connects one signal source to one of several destinations. In this case, each MAX355CWE+ channel implements a 4:1 configuration, allowing two multiplexers to route four sources per channel. Within the broader semiconductor hierarchy, the MAX355CWE+ is an analog switch IC, then a multiplexer, then an interface IC used to connect external signals to analog processing circuitry.
Key electrical characteristics include a maximum on-resistance of 350 ohms, maximum off leakage of 500 pA, and crosstalk of -92 dB at 100 kHz. The 350 ohm resistance is suitable for moderate-impedance sensor, measurement, and control paths rather than high-bandwidth, low-impedance video networks. Fault protection extends to 40 V beyond the supply rails, helping isolate sensitive downstream circuitry during abnormal input conditions.
The device uses a series N-channel, P-channel, and N-channel switching structure to provide fault protection. Its dual-mux architecture makes it useful where multiple analog inputs must be selected under software or hardware control. Control inputs allow the selected paths to be changed without mechanical switching, making the MAX355CWE+ appropriate for test systems, industrial controls, data acquisition modules, and instrumentation.
Typical uses include battery-powered monitoring equipment, industrial sensor interfaces, laboratory measurement systems, and analog test equipment. The 4.5 V minimum supply supports systems operating from a 5 V rail, while the 36 V maximum expands applicability to higher-voltage industrial environments. Protection is especially relevant where an external cable or sensor may present an overvoltage before system power stabilizes.
Designers should verify the input and output voltage limits against the specific fault condition and avoid treating the 40 V protection rating as a continuous operating rating. Keep analog routing paths away from high-current switching nodes, provide a stable bypass capacitor near the supply pins, and use high-impedance sensing circuits to reduce errors caused by the 350 ohm on-resistance.
This page combines the MAX355CWE+ electrical characteristics, application guidance, package information, and verified drop-in alternatives to support faster component selection and PCB replacement decisions.
直接替換替代品,適用於 MAX355CWE+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX355CWE+ (相同外形與佔位) — 差異在於 Multiplexer Configuration, On-Resistance, Package.
MAX355CWE
✅ 直接替換📋 參考替代品(不在目錄中)
MAX355EWE+
✅ 直接替換聯絡詢價
查看資料表 →MAX355CWE+ 規格
| Multiplexer Configuration | Dual 4:1 |
| Number of Circuits | 2 circuits |
| On-Resistance | 350 ohm maximum |
| Supply Voltage Range | 4.5 V to 36 V |
| Overvoltage Protection | Up to 40 V beyond supply rails |
| Off Leakage Current | 500 pA maximum |
| Crosstalk | -92 dB at 100 kHz |
| 工作溫度 | 0°C to 70°C |
| 封裝 | 16-SOIC, 7.50 mm width |
| Package Type | WSOIC-16 |
| 安裝類型 | Surface mount |
| Switch Structure | Series N-channel, P-channel, N-channel |
| Fault Protection | Protected during power-up, power-down, and fault conditions |
| Lead-Free Finish | Yes for MAX355CWE+ ordering suffix |
MAX355CWE+ wsoic-16 腳位配置指南
MAX355CWE+(wsoic-16 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX355CWE+.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX355CWE+ 適用於 6 應用s: Industrial Sensor Multiplexing, Data Acquisition Modules, Automated Test Equipment, Battery-Powered Monitoring Equipment, Laboratory Measurement Systems, High-Voltage Control Interfaces.
Industrial Sensor Multiplexing
The MAX355CWE+ fits industrial sensor interfaces that require several measured signals to share a limited analog front end. Each of its two independent 4:1 sections can connect one of four inputs to a common terminal, reducing the number of analog routing components needed. The 4.5 V to 36 V supply range supports both 5 V instrumentation and higher-voltage industrial rails, while protection up to 40 V beyond the supply rails helps manage transient faults. Because on-resistance reaches 350 ohm, the selected sensor impedance and allowable measurement error must be included in the signal-chain design.
推薦
Data Acquisition Modules
A dual 4:1 analog multiplexer is useful in compact data-acquisition modules where several inputs must be routed to a shared converter or measurement amplifier. The MAX355CWE+ provides two selectable four-input groups in one 16-WSOIC package, simplifying control logic and conserving board area. Its maximum off leakage of 500 pA and -92 dB crosstalk at 100 kHz help preserve signal integrity between channels, although the 350 ohm switch resistance should be compensated when the source impedance is finite. The 4.5 V minimum supply also supports conventional 5 V acquisition systems.
推薦
Automated Test Equipment
The MAX355CWE+ can route test signals among multiple sources in automated test equipment while providing fault isolation during startup or abnormal fixture conditions. Two 4:1 sections allow compact control of several test paths without requiring a separate switch for every channel. The maximum on-resistance of 350 ohm is generally appropriate for high-impedance test fixtures, and the -92 dB crosstalk specification at 100 kHz supports low-level signal measurements. Designers should still account for switch resistance, leakage, and settling time in the measurement accuracy budget.
推薦
Battery-Powered Monitoring Equipment
The MAX355CWE+ is suitable for battery-powered monitoring equipment that multiplexes sensor inputs while operating from a regulated 5 V system. Its dual 4:1 organization reduces wiring and component count in portable instruments, and fault protection helps prevent external sensor lines from exposing downstream circuitry to startup or shutdown overvoltage. The 4.5 V minimum supply fits a 5 V rail, while the 350 ohm maximum on-resistance is best matched to high-impedance sensors. Confirm that injected channel error remains acceptable at the lowest expected source impedance.
推薦
Laboratory Measurement Systems
Laboratory measurement systems can use the MAX355CWE+ to select among four input paths in each of two switch sections. The -92 dB crosstalk at 100 kHz and 500 pA maximum off leakage help maintain channel separation for precision measurements, while the 4:1 topology supports compact instrument front ends. The 350 ohm on-resistance is the primary accuracy consideration when driving amplifier inputs with finite impedance. Keep the routing traces short, maintain a quiet ground reference, and compare the complete measurement uncertainty against the selected switch resistance.
推薦
High-Voltage Control Interfaces
The MAX355CWE+ can interface control signals in systems operating across a broad supply range, including industrial 24 V and 36 V applications. Its 4.5 V to 36 V operating specification supports higher-voltage logic environments, and the fault-protected series N-channel, P-channel, and N-channel structure limits fault exposure beyond the normal rails. When switching external control lines, verify the absolute maximum input and output ratings, ensure the selected switch path does not exceed them, and provide local supply bypassing to maintain stable operation.
推薦
推薦產品摘要
工程參考資料,適用於 MAX355CWE+ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX355CWE | MAX355EWE+ |
|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| On-Resistance | 350 ohm maximum | 350 ohm maximum | 350 ohm maximum |
| Supply Voltage Range | 4.5 V to 36 V | 4.5 V to 36 V | 4.5 V to 36 V |
| Off Leakage Current | 500 pA maximum | 500 pA maximum | 500 pA maximum |
| Crosstalk | -92 dB at 100 kHz | -92 dB at 100 kHz | -92 dB at 100 kHz |
| Operating Temperature | 0°C to 70°C | 0°C to 70°C | -40°C to 85°C |
| Overvoltage Protection | Up to 40 V beyond supply rails | Up to 40 V beyond supply rails | Up to 40 V beyond supply rails |
主要差異化特點
- Combines two protected 4:1 multiplexers in one package (對比MAX355CWE)
- Maintains the same protected analog-switch architecture for exact-family replacement (對比MAX355EWE+)
- Commercial grade supports a 0°C to 70°C operating range (對比MAX355EWE+)
設計說明
Treat the 350 ohm maximum on-resistance as part of the signal-path impedance rather than as an ideal switch resistance. For a divider formed by this resistance and the receiving input impedance, the resulting error can be significant when the input impedance is only tens of kilohms. Use a high-impedance receiver or amplifier input, and include channel resistance and leakage in the measurement uncertainty calculation.
Place the supply bypass capacitor close to the device supply and ground pins, and keep analog switch traces short and separated from switching-current paths. The dual 4:1 topology can place sensitive signals near control or routed channels, so route the two groups with attention to crosstalk and ground return paths. A continuous ground reference under the device helps reduce coupling into the high-impedance measurement paths.
Do not confuse fault protection with a continuous overvoltage rating. The MAX355 family protects against overvoltage up to 40 V beyond the supply rails during power-up, power-down, and fault conditions, but normal operating voltages and absolute maximum ratings must still be respected. Also confirm the selected control logic and pin functions against the manufacturer datasheet rather than assigning control signals from generic multiplexer conventions.
Reserve the same 16-SOIC land pattern when evaluating MAX355CWE and MAX355EWE+ replacements. Verify body width, lead pitch, and pin orientation on the PCB rather than relying only on the generic package name. The two identified replacements use the same family architecture, but production qualification should still include control-state timing, temperature behavior, and the worst-case analog accuracy at the required source impedance.
合規資訊
The plus suffix identifies the lead-free ordering option. No explicit RoHS, REACH, halogen-free, conflict-minerals, or AEC-Q100 statement was included in the cited product records.