onsemi

TCA0372DP2G - Dual 1A Power Op Amp | onsemi

MPN: TCA0372DP2G ✗ জীবনকালের সমাপ্তি
5 V to 40 V Vdss 1.0 A Id 16-pin PDIP, 0.300 inch pitch Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

TCA0372DP2G সারাংশ

The onsemi TCA0372DP2G is a dual power operational amplifier rated for a 1.0 A output current and a 5 V to 40 V supply range in a 16-pin PDIP package. Its two amplifier channels are designed for power-level signal conditioning, including servo amplifiers, power supplies, and inductive loads. The manufacturer identifies the TCA0372 family as a monolithic dual power operational amplifier with no deadband crossover distortion.

A power operational amplifier is an integrated circuit that combines the voltage gain of an operational amplifier with the drive capability of a power output stage. This places the component in the amplifier IC hierarchy between precision signal amplifiers and discrete power-transistor stages. Its purpose is to amplify a low-level control signal while providing enough output current to drive loads that a conventional small-signal operational amplifier cannot handle directly.

The most important device-level specifications are the 1.0 A output-current capability, 5 V to 40 V operating supply range, 1.4 MHz bandwidth indication, and dual-channel configuration. The extended-temperature marking distinguishes this exact ordering code from catalog entries with narrower environmental coverage. Its power-output topology is particularly relevant when driving coils, motors, solenoids, or other loads where the output must remain linear across positive and negative signal excursions.

The two channels share the same monolithic power-amplifier architecture and are intended for applications requiring substantial output current without the discrete driver circuitry normally associated with power stages. Eliminating deadband crossover distortion can simplify feedback-loop design in bipolar or bidirectional drive systems because the output follows the command signal more directly around zero. Engineers should nevertheless account for supply headroom, output-current limits, load return paths, and the thermal load created during sustained high-current operation.

Typical uses include servo-amplifier control loops, regulated power-supply error amplifiers, motor and solenoid drivers, audio amplification, and industrial actuator interfaces. The 16-pin PDIP format favors through-hole construction and repairable assemblies. The same package can also support prototype and legacy-system maintenance where a high-current output stage must fit an existing dual-in-line board layout.

A robust design should use low-inductance supply and ground connections, place input and feedback components close to the relevant pins, and provide adequate copper and thermal dissipation around the output path. Feedback compensation and stability must be evaluated with the actual load impedance and cable capacitance. Current limiting or protection may also be required when the load can exceed the device's 1.0 A rating or develop an abrupt fault condition.

This product page combines the manufacturer datasheet, distributor catalog information, package details, lifecycle context, application guidance, and drop-in-replacement analysis. It is designed to support component selection, PCB planning, sourcing, and design review for engineers working with high-current dual power operational amplifiers.

এর জন্য ড্রপ-ইন বিকল্প TCA0372DP2G — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।

বিকল্প অনুরোধ করুন

TCA0372DP2G সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Amplifier Type Dual power operational amplifier
Number of Channels 2 channels
Output Current per Channel 1.0 A
Supply Voltage Range 5 V to 40 V
Gain-Bandwidth Product 1.4 MHz
Crossover Distortion No deadband crossover distortion
প্যাকেজ 16-pin PDIP, 0.300 inch pitch
মাউন্টিং টাইপ Through-hole
অপারেটিং তাপমাত্রা Extended temperature range
টপোলজি Monolithic power operational amplifier
আউটপুট কনফিগারেশন Dual-channel power output

TCA0372DP2G 16-pin pdip, 0.300 inch pitch পিন কনফিগারেশন গাইড

TCA0372DP2G (16-pin pdip, 0.300 inch pitch প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

TCA0372DP2G-এর জন্য 16-pin pdip, 0.300 inch pitch প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি TCA0372DP2G.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

TCA0372DP2G এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: DC Servo Amplifier, Industrial Solenoid Driver, Audio Power Amplifier, Power-Supply Error Amplifier, Position Feedback Amplifier, Legacy Industrial Control Board Repair.

🏭

DC Servo Amplifier

The TCA0372DP2G fits a DC servo control loop where a position or speed-error signal must drive a motor winding. Its two 1.0 A power-operational-amplifier channels can support complementary axes or a drive plus feedback channel, while the 5 V to 40 V range accommodates several industrial bus levels. Place the IC in the feedback path ahead of the motor winding and use low-inductance supply wiring. Confirm closed-loop stability, current limiting, and the maximum winding current before operation.

⚡

Industrial Solenoid Driver

The TCA0372DP2G can drive a solenoid or relay coil when the application requires bidirectional current and more output drive than a small-signal operational amplifier provides. Its 1.0 A channel rating is relevant for coils whose steady-state and inrush currents remain within the device limits, while the no-deadband characteristic supports control around the zero-output transition. Use a flyback path and current protection appropriate to the inductive load, and verify thermal rise during the longest energized interval.

🎧

Audio Power Amplifier

The TCA0372DP2G is suitable for audio or motor-control power stages where a compact dual output amplifier is advantageous. The 1.0 A output capability can supply substantially more current than a conventional precision op amp, and the absence of deadband crossover distortion improves linearity around zero. In a practical implementation, use one channel per stereo output or configure the channels for bridged operation only if the manufacturer supports that topology. Account for speaker impedance, DC offset, output-stage dissipation, and stable feedback-network values.

🔋

Power-Supply Error Amplifier

The TCA0372DP2G can be used as the high-current error amplifier in a power-supply control loop, taking advantage of its monolithic power-output design and 5 V to 40 V operating range. Two channels allow separate positive and negative outputs in a split-supply architecture or independent control functions. The amplifier should operate inside its feedback-stability envelope with realistic output impedance and load capacitance. Check output swing, saturation recovery, compensation, and transient response at the minimum and maximum intended supply voltages.

📱

Position Feedback Amplifier

The dual channels of the TCA0372DP2G can process position feedback while also providing a power-drive function in a multi-axis actuator controller. This arrangement can reduce the number of separate power amplifiers in a system where one channel performs low-level signal amplification and the other drives the load. Keep feedback routing away from motor-current paths, use a solid ground reference, and validate that the selected channel configuration meets input-common-mode, output-swing, and gain-bandwidth requirements.

🔧

Legacy Industrial Control Board Repair

The 16-pin PDIP package makes the TCA0372DP2G useful for repairing or extending legacy through-hole industrial control boards that require a high-current dual amplifier stage. The 1.0 A output class and 5 V to 40 V supply range are suited to older actuator and servo-control architectures. Before installation, compare the complete pinout and compensation values against the original device, inspect socketed or soldered joints, and allow for less thermal margin than a modern surface-mount implementation.

What is the onsemi TCA0372DP2G?
The onsemi TCA0372DP2G is a monolithic dual power operational amplifier with two 1.0 A output channels, a 5 V to 40 V supply range, and a 1.4 MHz bandwidth indication. According to the onsemi TCA0372 datasheet, it is intended for applications including servo amplifiers, power supplies, and inductive loads, while its no-deadband crossover-distortion design improves signal following around zero.
What is the output current of TCA0372DP2G?
The TCA0372DP2G is rated for 1.0 A output current in each power-operational-amplifier channel. This rating identifies it as a power-output amplifier rather than a conventional low-current precision op amp. The onsemi datasheet describes the device as a dual power operational amplifier for loads such as coils, servo motors, and power-supply control stages.
What is the supply voltage range of TCA0372DP2G?
The TCA0372DP2G operates from 5 V to 40 V, according to the onsemi TCA0372 datasheet and distributor catalog information. This broad supply range accommodates industrial control systems and higher-voltage power circuits. Actual signal swing and output-current capability remain dependent on the supply voltage, load, output configuration, and thermal conditions.
Where can I download the TCA0372DP2G datasheet PDF?
The official TCA0372 family datasheet is available from onsemi at https://www.onsemi.com/pdf/datasheet/tca0372-d.pdf. It covers the TCA0372, TCA0372B, and NCV0372B devices, including the power-output architecture, supply range, output-current capability, application circuits, package information, and recommended operating conditions. Use the pin-description table in that document when assigning PCB connections.
Where can I find the TCA0372DP2G pinout?
The TCA0372DP2G pinout is contained in the pin-description table of the official onsemi TCA0372 datasheet. The component uses a 16-pin PDIP package with 0.300-inch pitch, as identified by the distributor catalog entry. Use the package drawing and pin table together when assigning power, ground, input, output, compensation, and bias connections on a new layout.
What can replace TCA0372DP2G?
The closest published same-family comparison is TCA0372DP1G, but it should not be treated as an automatic drop-in replacement without checking its complete pinout and electrical limits against the onsemi datasheets. No verified five-part set of same-package, pin-to-pin alternatives was identified. Use the onsemi cross-reference tool and compare supply range, output current, bandwidth, thermal limits, and every package connection before approving a substitution.
Is TCA0372DP2G the same as TCA0372DP1G?
The TCA0372DP2G and TCA0372DP1G belong to the same onsemi TCA0372 family, but their exact ordering codes must not be assumed interchangeable. Published comparison data confirms that catalog tools distinguish the two devices, while the provided information does not establish every electrical and pin-level difference. Verify the manufacturer pin and specification tables before using TCA0372DP1G as a replacement.
TCA0372DP2G vs TCA0372DP1G: which is better for a servo amplifier?
Choose TCA0372DP2G when its exact datasheet ratings match the servo-amplifier design, including the 1.0 A output-current class, 5 V to 40 V supply range, and 16-pin PDIP footprint. TCA0372DP1G may offer a lower-cost procurement path within the same family, but the available comparison does not quantify all rating differences. Validate feedback stability, output swing, thermal dissipation, and pin compatibility before selecting it.
TCA0372DP2G vs TCA0372DM2ELG: can DM2ELG replace DP2G?
TCA0372DM2ELG is not a direct PCB drop-in substitute for TCA0372DP2G because the published comparison distinguishes their package and mounting styles. The DP2G uses a 16-pin PDIP format, while the DM2ELG ordering code denotes a different package family. Use TCA0372DM2ELG only when the board can be redesigned and its electrical ratings satisfy the original load and thermal requirements.
When should I choose TCA0372DP2G over a discrete power-output stage?
Choose TCA0372DP2G when the design needs bidirectional or signed drive from a compact 16-pin through-hole package and can stay within its 1.0 A channel rating. Its integrated power-operational-amplifier topology can reduce the number of discrete driver stages needed for moderate inductive loads. A discrete stage may still be preferable for higher sustained current, lower dissipation, isolation, or protection requirements not met by the IC.
Is TCA0372DP2G suitable for driving an inductive load?
Yes, the onsemi datasheet identifies inductive loading and servo-amplifier use as intended applications for the TCA0372 family. The 1.0 A output-current rating provides the drive level for suitable coils and actuators, but the load must remain within current, voltage, frequency, and thermal limits. Add protection appropriate to the load and verify inductive energy handling before energizing the circuit.
How should TCA0372DP2G be thermally managed?
Size the PCB heat path for the maximum sustained output dissipation, not merely the 1.0 A current rating. Estimated: output dissipation equals the average voltage across the output device multiplied by average output current, and junction temperature rises according to the actual junction-to-ambient thermal resistance of the installed PDIP package and copper layout. Request the complete thermal data from the onsemi datasheet before setting the maximum allowable load.
What does the 1.4 MHz specification mean for TCA0372DP2G design?
The 1.4 MHz figure identifies the amplifier's nominal bandwidth class and indicates how quickly small-signal gain can roll off with frequency. It is not a guarantee that the power output can drive a 1.0 A load at 1.4 MHz; output-current capability generally decreases as frequency rises and supply headroom is reduced. Use the manufacturer gain, slew-rate, output-swing, and stability curves for the intended closed-loop design.
Where to buy TCA0372DP2G online?
Use the Request a Quote form on this XAIPART product page to request TCA0372DP2G pricing, stock confirmation, and current lead time. The form allows buyers to identify the exact 16-pin PDIP ordering code and obtain a current commercial response without relying on a static catalog price. Confirm lifecycle status, packaging, quantity breaks, and shipment condition when placing the order.
What is the price and lead time for TCA0372DP2G?
Current price and lead time for TCA0372DP2G should be obtained through the Request a Quote form on this page because commercial terms can change with inventory, lifecycle status, package quantity, and order volume. The form should also confirm the exact suffix and lead time for the 16-pin PDIP device. No static price should be used for budgeting without a current quote.
Is TCA0372DP2G in stock?
Current TCA0372DP2G inventory should be confirmed through the Request a Quote form on this XAIPART page, including the required quantity and acceptable delivery date. Marketplace and distributor catalog pages may represent different stocking locations, package quantities, or fulfillment schedules. A confirmed XAIPART quotation provides the most direct answer for production planning and assembly scheduling.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা TCA0372DP2G — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose TCA0372DP2G for through-hole servo, actuator, audio, or power-control designs that need two 1.0 A-class power-op-amp channels, a 5 V to 40 V supply range, and no deadband crossover distortion. Its PDIP format is particularly useful for legacy-board maintenance and moderate-current through-hole assemblies. Consider TCA0372DP1G only after comparing the complete electrical ratings and 16-pin connection table; it is not automatically interchangeable merely because it belongs to the same family. TCA0372DM2ELG is unsuitable as a no-redesign replacement because its package differs. For sustained loads near 1.0 A, first verify output-current derating, safe operating limits, thermal resistance, and the SOA-like behavior of the selected output configuration. If the design requires greater continuous current, lower distortion, smaller size, or integrated current protection, compare a modern power-output amplifier or discrete MOSFET stage instead.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য
Package 16-pin PDIP, 0.300-inch pitch
Brand onsemi
Amplifier Configuration Dual power operational amplifier
Output Current 1.0 A per channel
Supply Voltage Range 5 V to 40 V
Gain-Bandwidth Product 1.4 MHz
Crossover Distortion No deadband crossover distortion
Mounting Type Through-hole
Intended Load Class Inductive loads, servo amplifiers, and power supplies

মূল পার্থক্যসমূহ

  • High output-current capability in a dual through-hole package (বনামTCA0372DP1G)
  • No deadband crossover distortion (বনামTCA0372DP1G)
  • Broad operating supply class (বনামTCA0372DM2ELG)

ডিজাইন নোট

Calculate dissipation from the actual output waveform rather than multiplying the 1.0 A rating by total supply voltage. Estimated: P_out equals the average output-device voltage multiplied by average output current. Add approximately 1 A times supply voltage times quiescent current for internal bias loss, then compare the total with the PDIP thermal resistance and available copper area. Add airflow or reduce load current if the calculated junction temperature exceeds the manufacturer limit.

Route the output current and supply current on wide, short paths, and connect the power ground directly to the relevant package and bypass-capacitor ground pins. Place input, feedback, and compensation components close to their pins to minimize parasitic feedback. For an inductive load, keep motor or coil wiring away from input and feedback traces, and provide a defined return path for switching current so the amplifier does not share noisy return paths with sensitive signals.

Do not treat the 1.0 A output rating as a continuous rating for every load, supply, or ambient temperature. Check peak current, repetitive current, output-voltage swing, and thermal limits separately. Also avoid assuming that a family member with a similar ordering code is pin-compatible: compare each of the 16 connections, including bias and compensation pins, and confirm that replacement feedback values do not create instability.

Use local supply bypassing close to the IC and provide additional bulk capacitance where the remote supply cannot respond quickly to load transitions. Check the capacitor voltage rating against the maximum 40 V supply. The bypass network should suppress ripple without adding excessive loop inductance, and its stability effect must be included in closed-loop evaluation because changes near a power amplifier can alter output-pole behavior.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The manufacturer datasheet and distributor listings do not explicitly establish the requested compliance status. No automotive qualification is claimed for this through-hole power operational amplifier.

ডেটা যাচাই করা হয়েছে: 2026-11-16 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

TCA0372DP2G datasheet TCA0372DP2G datasheet pdf TCA0372DP2G pinout TCA0372DP2G equivalent TCA0372DP2G replacement TCA0372DP2G cross reference TCA0372DP2G vs TCA0372DP1G TCA0372DP2G vs TCA0372DM2ELG TCA0372DP2G 1A power op amp TCA0372DP2G 16-PDIP onsemi TCA0372DP2G TCA0372DP2G servo amplifier TCA0372DP2G price TCA0372DP2G stock

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

onsemi TCA0372DP2G TCA0372DP1G TCA0372DM2ELG TCA0372 power operational amplifier operational amplifier amplifier IC semiconductor monolithic dual amplifier power output stage 1.0 A output current 5 V to 40 V supply voltage 1.4 MHz bandwidth no deadband crossover distortion inductive loading servo amplifier power-supply control 16-pin PDIP PDIP package family through-hole mounting surface-mount alternative feedback stability thermal dissipation
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন