TCA0372DP2G - Dual 1A Power Op Amp | onsemi
N.º de pieza: TCA0372DP2G ✗ Fin de vidaTCA0372DP2G Descripción general
A power operational amplifier is an integrated circuit that combines the voltage gain of an operational amplifier with the drive capability of a power output stage. This places the component in the amplifier IC hierarchy between precision signal amplifiers and discrete power-transistor stages. Its purpose is to amplify a low-level control signal while providing enough output current to drive loads that a conventional small-signal operational amplifier cannot handle directly.
The most important device-level specifications are the 1.0 A output-current capability, 5 V to 40 V operating supply range, 1.4 MHz bandwidth indication, and dual-channel configuration. The extended-temperature marking distinguishes this exact ordering code from catalog entries with narrower environmental coverage. Its power-output topology is particularly relevant when driving coils, motors, solenoids, or other loads where the output must remain linear across positive and negative signal excursions.
The two channels share the same monolithic power-amplifier architecture and are intended for applications requiring substantial output current without the discrete driver circuitry normally associated with power stages. Eliminating deadband crossover distortion can simplify feedback-loop design in bipolar or bidirectional drive systems because the output follows the command signal more directly around zero. Engineers should nevertheless account for supply headroom, output-current limits, load return paths, and the thermal load created during sustained high-current operation.
Typical uses include servo-amplifier control loops, regulated power-supply error amplifiers, motor and solenoid drivers, audio amplification, and industrial actuator interfaces. The 16-pin PDIP format favors through-hole construction and repairable assemblies. The same package can also support prototype and legacy-system maintenance where a high-current output stage must fit an existing dual-in-line board layout.
A robust design should use low-inductance supply and ground connections, place input and feedback components close to the relevant pins, and provide adequate copper and thermal dissipation around the output path. Feedback compensation and stability must be evaluated with the actual load impedance and cable capacitance. Current limiting or protection may also be required when the load can exceed the device's 1.0 A rating or develop an abrupt fault condition.
This product page combines the manufacturer datasheet, distributor catalog information, package details, lifecycle context, application guidance, and drop-in-replacement analysis. It is designed to support component selection, PCB planning, sourcing, and design review for engineers working with high-current dual power operational amplifiers.
Alternativas directas para TCA0372DP2G — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasTCA0372DP2G Valores máximos y características eléctricas
| Amplifier Type | Dual power operational amplifier |
| Number of Channels | 2 channels |
| Output Current per Channel | 1.0 A |
| Supply Voltage Range | 5 V to 40 V |
| Gain-Bandwidth Product | 1.4 MHz |
| Crossover Distortion | No deadband crossover distortion |
| Encapsulado | 16-pin PDIP, 0.300 inch pitch |
| Tipo de montaje | Through-hole |
| Temperatura de funcionamiento | Extended temperature range |
| Topología | Monolithic power operational amplifier |
| Configuración de salida | Dual-channel power output |
Guía de configuración de pines de TCA0372DP2G 16-pin pdip, 0.300 inch pitch
Configuración de pines para TCA0372DP2G (encapsulado 16-pin pdip, 0.300 inch pitch). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para TCA0372DP2G.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
TCA0372DP2G es adecuado para 6 aplicacións: DC Servo Amplifier, Industrial Solenoid Driver, Audio Power Amplifier, Power-Supply Error Amplifier, Position Feedback Amplifier, Legacy Industrial Control Board Repair.
DC Servo Amplifier
The TCA0372DP2G fits a DC servo control loop where a position or speed-error signal must drive a motor winding. Its two 1.0 A power-operational-amplifier channels can support complementary axes or a drive plus feedback channel, while the 5 V to 40 V range accommodates several industrial bus levels. Place the IC in the feedback path ahead of the motor winding and use low-inductance supply wiring. Confirm closed-loop stability, current limiting, and the maximum winding current before operation.
Recomendado
Industrial Solenoid Driver
The TCA0372DP2G can drive a solenoid or relay coil when the application requires bidirectional current and more output drive than a small-signal operational amplifier provides. Its 1.0 A channel rating is relevant for coils whose steady-state and inrush currents remain within the device limits, while the no-deadband characteristic supports control around the zero-output transition. Use a flyback path and current protection appropriate to the inductive load, and verify thermal rise during the longest energized interval.
Recomendado
Audio Power Amplifier
The TCA0372DP2G is suitable for audio or motor-control power stages where a compact dual output amplifier is advantageous. The 1.0 A output capability can supply substantially more current than a conventional precision op amp, and the absence of deadband crossover distortion improves linearity around zero. In a practical implementation, use one channel per stereo output or configure the channels for bridged operation only if the manufacturer supports that topology. Account for speaker impedance, DC offset, output-stage dissipation, and stable feedback-network values.
Recomendado
Power-Supply Error Amplifier
The TCA0372DP2G can be used as the high-current error amplifier in a power-supply control loop, taking advantage of its monolithic power-output design and 5 V to 40 V operating range. Two channels allow separate positive and negative outputs in a split-supply architecture or independent control functions. The amplifier should operate inside its feedback-stability envelope with realistic output impedance and load capacitance. Check output swing, saturation recovery, compensation, and transient response at the minimum and maximum intended supply voltages.
Recomendado
Position Feedback Amplifier
The dual channels of the TCA0372DP2G can process position feedback while also providing a power-drive function in a multi-axis actuator controller. This arrangement can reduce the number of separate power amplifiers in a system where one channel performs low-level signal amplification and the other drives the load. Keep feedback routing away from motor-current paths, use a solid ground reference, and validate that the selected channel configuration meets input-common-mode, output-swing, and gain-bandwidth requirements.
Recomendado
Legacy Industrial Control Board Repair
The 16-pin PDIP package makes the TCA0372DP2G useful for repairing or extending legacy through-hole industrial control boards that require a high-current dual amplifier stage. The 1.0 A output class and 5 V to 40 V supply range are suited to older actuator and servo-control architectures. Before installation, compare the complete pinout and compensation values against the original device, inspect socketed or soldered joints, and allow for less thermal margin than a modern surface-mount implementation.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TCA0372DP2G — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Package | 16-pin PDIP, 0.300-inch pitch |
| Brand | onsemi |
| Amplifier Configuration | Dual power operational amplifier |
| Output Current | 1.0 A per channel |
| Supply Voltage Range | 5 V to 40 V |
| Gain-Bandwidth Product | 1.4 MHz |
| Crossover Distortion | No deadband crossover distortion |
| Mounting Type | Through-hole |
| Intended Load Class | Inductive loads, servo amplifiers, and power supplies |
Diferenciadores clave
- High output-current capability in a dual through-hole package (frente a TCA0372DP1G)
- No deadband crossover distortion (frente a TCA0372DP1G)
- Broad operating supply class (frente a TCA0372DM2ELG)
Notas de diseño
Calculate dissipation from the actual output waveform rather than multiplying the 1.0 A rating by total supply voltage. Estimated: P_out equals the average output-device voltage multiplied by average output current. Add approximately 1 A times supply voltage times quiescent current for internal bias loss, then compare the total with the PDIP thermal resistance and available copper area. Add airflow or reduce load current if the calculated junction temperature exceeds the manufacturer limit.
Route the output current and supply current on wide, short paths, and connect the power ground directly to the relevant package and bypass-capacitor ground pins. Place input, feedback, and compensation components close to their pins to minimize parasitic feedback. For an inductive load, keep motor or coil wiring away from input and feedback traces, and provide a defined return path for switching current so the amplifier does not share noisy return paths with sensitive signals.
Do not treat the 1.0 A output rating as a continuous rating for every load, supply, or ambient temperature. Check peak current, repetitive current, output-voltage swing, and thermal limits separately. Also avoid assuming that a family member with a similar ordering code is pin-compatible: compare each of the 16 connections, including bias and compensation pins, and confirm that replacement feedback values do not create instability.
Use local supply bypassing close to the IC and provide additional bulk capacitance where the remote supply cannot respond quickly to load transitions. Check the capacitor voltage rating against the maximum 40 V supply. The bypass network should suppress ripple without adding excessive loop inductance, and its stability effect must be included in closed-loop evaluation because changes near a power amplifier can alter output-pole behavior.
Información de cumplimiento
The manufacturer datasheet and distributor listings do not explicitly establish the requested compliance status. No automotive qualification is claimed for this through-hole power operational amplifier.