TCA0372DP2G - Dual 1A Power Op Amp | onsemi
MPN: TCA0372DP2G ✗ Cuối đờiTCA0372DP2G Tóm tắt
A power operational amplifier is an integrated circuit that combines the voltage gain of an operational amplifier with the drive capability of a power output stage. This places the component in the amplifier IC hierarchy between precision signal amplifiers and discrete power-transistor stages. Its purpose is to amplify a low-level control signal while providing enough output current to drive loads that a conventional small-signal operational amplifier cannot handle directly.
The most important device-level specifications are the 1.0 A output-current capability, 5 V to 40 V operating supply range, 1.4 MHz bandwidth indication, and dual-channel configuration. The extended-temperature marking distinguishes this exact ordering code from catalog entries with narrower environmental coverage. Its power-output topology is particularly relevant when driving coils, motors, solenoids, or other loads where the output must remain linear across positive and negative signal excursions.
The two channels share the same monolithic power-amplifier architecture and are intended for applications requiring substantial output current without the discrete driver circuitry normally associated with power stages. Eliminating deadband crossover distortion can simplify feedback-loop design in bipolar or bidirectional drive systems because the output follows the command signal more directly around zero. Engineers should nevertheless account for supply headroom, output-current limits, load return paths, and the thermal load created during sustained high-current operation.
Typical uses include servo-amplifier control loops, regulated power-supply error amplifiers, motor and solenoid drivers, audio amplification, and industrial actuator interfaces. The 16-pin PDIP format favors through-hole construction and repairable assemblies. The same package can also support prototype and legacy-system maintenance where a high-current output stage must fit an existing dual-in-line board layout.
A robust design should use low-inductance supply and ground connections, place input and feedback components close to the relevant pins, and provide adequate copper and thermal dissipation around the output path. Feedback compensation and stability must be evaluated with the actual load impedance and cable capacitance. Current limiting or protection may also be required when the load can exceed the device's 1.0 A rating or develop an abrupt fault condition.
This product page combines the manufacturer datasheet, distributor catalog information, package details, lifecycle context, application guidance, and drop-in-replacement analysis. It is designed to support component selection, PCB planning, sourcing, and design review for engineers working with high-current dual power operational amplifiers.
Bộ thay thế dễ dàng lắp đặt cho TCA0372DP2G — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếTCA0372DP2G Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Dual power operational amplifier |
| Number of Channels | 2 channels |
| Output Current per Channel | 1.0 A |
| Supply Voltage Range | 5 V to 40 V |
| Gain-Bandwidth Product | 1.4 MHz |
| Crossover Distortion | No deadband crossover distortion |
| Hộp | 16-pin PDIP, 0.300 inch pitch |
| Kiểu lắp đặt | Through-hole |
| Nhiệt độ hoạt động | Extended temperature range |
| Cấu trúc | Monolithic power operational amplifier |
| Cấu hình đầu ra | Dual-channel power output |
Hướng dẫn cấu hình chân TCA0372DP2G 16-pin pdip, 0.300 inch pitch
Cấu hình chân cho TCA0372DP2G (16-pin pdip, 0.300 inch pitch gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TCA0372DP2G.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TCA0372DP2G phù hợp cho 6 Áp dụngs: DC Servo Amplifier, Industrial Solenoid Driver, Audio Power Amplifier, Power-Supply Error Amplifier, Position Feedback Amplifier, Legacy Industrial Control Board Repair.
DC Servo Amplifier
The TCA0372DP2G fits a DC servo control loop where a position or speed-error signal must drive a motor winding. Its two 1.0 A power-operational-amplifier channels can support complementary axes or a drive plus feedback channel, while the 5 V to 40 V range accommodates several industrial bus levels. Place the IC in the feedback path ahead of the motor winding and use low-inductance supply wiring. Confirm closed-loop stability, current limiting, and the maximum winding current before operation.
Được đề xuất
Industrial Solenoid Driver
The TCA0372DP2G can drive a solenoid or relay coil when the application requires bidirectional current and more output drive than a small-signal operational amplifier provides. Its 1.0 A channel rating is relevant for coils whose steady-state and inrush currents remain within the device limits, while the no-deadband characteristic supports control around the zero-output transition. Use a flyback path and current protection appropriate to the inductive load, and verify thermal rise during the longest energized interval.
Được đề xuất
Audio Power Amplifier
The TCA0372DP2G is suitable for audio or motor-control power stages where a compact dual output amplifier is advantageous. The 1.0 A output capability can supply substantially more current than a conventional precision op amp, and the absence of deadband crossover distortion improves linearity around zero. In a practical implementation, use one channel per stereo output or configure the channels for bridged operation only if the manufacturer supports that topology. Account for speaker impedance, DC offset, output-stage dissipation, and stable feedback-network values.
Được đề xuất
Power-Supply Error Amplifier
The TCA0372DP2G can be used as the high-current error amplifier in a power-supply control loop, taking advantage of its monolithic power-output design and 5 V to 40 V operating range. Two channels allow separate positive and negative outputs in a split-supply architecture or independent control functions. The amplifier should operate inside its feedback-stability envelope with realistic output impedance and load capacitance. Check output swing, saturation recovery, compensation, and transient response at the minimum and maximum intended supply voltages.
Được đề xuất
Position Feedback Amplifier
The dual channels of the TCA0372DP2G can process position feedback while also providing a power-drive function in a multi-axis actuator controller. This arrangement can reduce the number of separate power amplifiers in a system where one channel performs low-level signal amplification and the other drives the load. Keep feedback routing away from motor-current paths, use a solid ground reference, and validate that the selected channel configuration meets input-common-mode, output-swing, and gain-bandwidth requirements.
Được đề xuất
Legacy Industrial Control Board Repair
The 16-pin PDIP package makes the TCA0372DP2G useful for repairing or extending legacy through-hole industrial control boards that require a high-current dual amplifier stage. The 1.0 A output class and 5 V to 40 V supply range are suited to older actuator and servo-control architectures. Before installation, compare the complete pinout and compensation values against the original device, inspect socketed or soldered joints, and allow for less thermal margin than a modern surface-mount implementation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TCA0372DP2G — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Package | 16-pin PDIP, 0.300-inch pitch |
| Brand | onsemi |
| Amplifier Configuration | Dual power operational amplifier |
| Output Current | 1.0 A per channel |
| Supply Voltage Range | 5 V to 40 V |
| Gain-Bandwidth Product | 1.4 MHz |
| Crossover Distortion | No deadband crossover distortion |
| Mounting Type | Through-hole |
| Intended Load Class | Inductive loads, servo amplifiers, and power supplies |
Bảo phân biệt quan trọng
- High output-current capability in a dual through-hole package (vsTCA0372DP1G)
- No deadband crossover distortion (vsTCA0372DP1G)
- Broad operating supply class (vsTCA0372DM2ELG)
Ghi chú thiết kế
Calculate dissipation from the actual output waveform rather than multiplying the 1.0 A rating by total supply voltage. Estimated: P_out equals the average output-device voltage multiplied by average output current. Add approximately 1 A times supply voltage times quiescent current for internal bias loss, then compare the total with the PDIP thermal resistance and available copper area. Add airflow or reduce load current if the calculated junction temperature exceeds the manufacturer limit.
Route the output current and supply current on wide, short paths, and connect the power ground directly to the relevant package and bypass-capacitor ground pins. Place input, feedback, and compensation components close to their pins to minimize parasitic feedback. For an inductive load, keep motor or coil wiring away from input and feedback traces, and provide a defined return path for switching current so the amplifier does not share noisy return paths with sensitive signals.
Do not treat the 1.0 A output rating as a continuous rating for every load, supply, or ambient temperature. Check peak current, repetitive current, output-voltage swing, and thermal limits separately. Also avoid assuming that a family member with a similar ordering code is pin-compatible: compare each of the 16 connections, including bias and compensation pins, and confirm that replacement feedback values do not create instability.
Use local supply bypassing close to the IC and provide additional bulk capacitance where the remote supply cannot respond quickly to load transitions. Check the capacitor voltage rating against the maximum 40 V supply. The bypass network should suppress ripple without adding excessive loop inductance, and its stability effect must be included in closed-loop evaluation because changes near a power amplifier can alter output-pole behavior.
Thông tin tuân thủ
The manufacturer datasheet and distributor listings do not explicitly establish the requested compliance status. No automotive qualification is claimed for this through-hole power operational amplifier.