TCA0372DP2G - Dual 1A Power Op Amp | onsemi
料号: TCA0372DP2G ✗ 停产TCA0372DP2G 概述
A power operational amplifier is an integrated circuit that combines the voltage gain of an operational amplifier with the drive capability of a power output stage. This places the component in the amplifier IC hierarchy between precision signal amplifiers and discrete power-transistor stages. Its purpose is to amplify a low-level control signal while providing enough output current to drive loads that a conventional small-signal operational amplifier cannot handle directly.
The most important device-level specifications are the 1.0 A output-current capability, 5 V to 40 V operating supply range, 1.4 MHz bandwidth indication, and dual-channel configuration. The extended-temperature marking distinguishes this exact ordering code from catalog entries with narrower environmental coverage. Its power-output topology is particularly relevant when driving coils, motors, solenoids, or other loads where the output must remain linear across positive and negative signal excursions.
The two channels share the same monolithic power-amplifier architecture and are intended for applications requiring substantial output current without the discrete driver circuitry normally associated with power stages. Eliminating deadband crossover distortion can simplify feedback-loop design in bipolar or bidirectional drive systems because the output follows the command signal more directly around zero. Engineers should nevertheless account for supply headroom, output-current limits, load return paths, and the thermal load created during sustained high-current operation.
Typical uses include servo-amplifier control loops, regulated power-supply error amplifiers, motor and solenoid drivers, audio amplification, and industrial actuator interfaces. The 16-pin PDIP format favors through-hole construction and repairable assemblies. The same package can also support prototype and legacy-system maintenance where a high-current output stage must fit an existing dual-in-line board layout.
A robust design should use low-inductance supply and ground connections, place input and feedback components close to the relevant pins, and provide adequate copper and thermal dissipation around the output path. Feedback compensation and stability must be evaluated with the actual load impedance and cable capacitance. Current limiting or protection may also be required when the load can exceed the device's 1.0 A rating or develop an abrupt fault condition.
This product page combines the manufacturer datasheet, distributor catalog information, package details, lifecycle context, application guidance, and drop-in-replacement analysis. It is designed to support component selection, PCB planning, sourcing, and design review for engineers working with high-current dual power operational amplifiers.
直接替换替代料: TCA0372DP2G ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料TCA0372DP2G 最大额定值与电气特性
| Amplifier Type | Dual power operational amplifier |
| Number of Channels | 2 channels |
| Output Current per Channel | 1.0 A |
| Supply Voltage Range | 5 V to 40 V |
| Gain-Bandwidth Product | 1.4 MHz |
| Crossover Distortion | No deadband crossover distortion |
| 封装 | 16-pin PDIP, 0.300 inch pitch |
| 安装类型 | Through-hole |
| 工作温度 | Extended temperature range |
| 拓扑 | Monolithic power operational amplifier |
| 输出配置 | Dual-channel power output |
TCA0372DP2G 16-pin pdip, 0.300 inch pitch 引脚配置指南
TCA0372DP2G(16-pin pdip, 0.300 inch pitch 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TCA0372DP2G.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TCA0372DP2G 适用于 6 应用s: DC Servo Amplifier, Industrial Solenoid Driver, Audio Power Amplifier, Power-Supply Error Amplifier, Position Feedback Amplifier, Legacy Industrial Control Board Repair.
DC Servo Amplifier
The TCA0372DP2G fits a DC servo control loop where a position or speed-error signal must drive a motor winding. Its two 1.0 A power-operational-amplifier channels can support complementary axes or a drive plus feedback channel, while the 5 V to 40 V range accommodates several industrial bus levels. Place the IC in the feedback path ahead of the motor winding and use low-inductance supply wiring. Confirm closed-loop stability, current limiting, and the maximum winding current before operation.
推荐
Industrial Solenoid Driver
The TCA0372DP2G can drive a solenoid or relay coil when the application requires bidirectional current and more output drive than a small-signal operational amplifier provides. Its 1.0 A channel rating is relevant for coils whose steady-state and inrush currents remain within the device limits, while the no-deadband characteristic supports control around the zero-output transition. Use a flyback path and current protection appropriate to the inductive load, and verify thermal rise during the longest energized interval.
推荐
Audio Power Amplifier
The TCA0372DP2G is suitable for audio or motor-control power stages where a compact dual output amplifier is advantageous. The 1.0 A output capability can supply substantially more current than a conventional precision op amp, and the absence of deadband crossover distortion improves linearity around zero. In a practical implementation, use one channel per stereo output or configure the channels for bridged operation only if the manufacturer supports that topology. Account for speaker impedance, DC offset, output-stage dissipation, and stable feedback-network values.
推荐
Power-Supply Error Amplifier
The TCA0372DP2G can be used as the high-current error amplifier in a power-supply control loop, taking advantage of its monolithic power-output design and 5 V to 40 V operating range. Two channels allow separate positive and negative outputs in a split-supply architecture or independent control functions. The amplifier should operate inside its feedback-stability envelope with realistic output impedance and load capacitance. Check output swing, saturation recovery, compensation, and transient response at the minimum and maximum intended supply voltages.
推荐
Position Feedback Amplifier
The dual channels of the TCA0372DP2G can process position feedback while also providing a power-drive function in a multi-axis actuator controller. This arrangement can reduce the number of separate power amplifiers in a system where one channel performs low-level signal amplification and the other drives the load. Keep feedback routing away from motor-current paths, use a solid ground reference, and validate that the selected channel configuration meets input-common-mode, output-swing, and gain-bandwidth requirements.
推荐
Legacy Industrial Control Board Repair
The 16-pin PDIP package makes the TCA0372DP2G useful for repairing or extending legacy through-hole industrial control boards that require a high-current dual amplifier stage. The 1.0 A output class and 5 V to 40 V supply range are suited to older actuator and servo-control architectures. Before installation, compare the complete pinout and compensation values against the original device, inspect socketed or soldered joints, and allow for less thermal margin than a modern surface-mount implementation.
推荐
推荐产品汇总
工程参考数据: TCA0372DP2G ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Package | 16-pin PDIP, 0.300-inch pitch |
| Brand | onsemi |
| Amplifier Configuration | Dual power operational amplifier |
| Output Current | 1.0 A per channel |
| Supply Voltage Range | 5 V to 40 V |
| Gain-Bandwidth Product | 1.4 MHz |
| Crossover Distortion | No deadband crossover distortion |
| Mounting Type | Through-hole |
| Intended Load Class | Inductive loads, servo amplifiers, and power supplies |
关键差异点
- High output-current capability in a dual through-hole package (对比 TCA0372DP1G)
- No deadband crossover distortion (对比 TCA0372DP1G)
- Broad operating supply class (对比 TCA0372DM2ELG)
设计说明
Calculate dissipation from the actual output waveform rather than multiplying the 1.0 A rating by total supply voltage. Estimated: P_out equals the average output-device voltage multiplied by average output current. Add approximately 1 A times supply voltage times quiescent current for internal bias loss, then compare the total with the PDIP thermal resistance and available copper area. Add airflow or reduce load current if the calculated junction temperature exceeds the manufacturer limit.
Route the output current and supply current on wide, short paths, and connect the power ground directly to the relevant package and bypass-capacitor ground pins. Place input, feedback, and compensation components close to their pins to minimize parasitic feedback. For an inductive load, keep motor or coil wiring away from input and feedback traces, and provide a defined return path for switching current so the amplifier does not share noisy return paths with sensitive signals.
Do not treat the 1.0 A output rating as a continuous rating for every load, supply, or ambient temperature. Check peak current, repetitive current, output-voltage swing, and thermal limits separately. Also avoid assuming that a family member with a similar ordering code is pin-compatible: compare each of the 16 connections, including bias and compensation pins, and confirm that replacement feedback values do not create instability.
Use local supply bypassing close to the IC and provide additional bulk capacitance where the remote supply cannot respond quickly to load transitions. Check the capacitor voltage rating against the maximum 40 V supply. The bypass network should suppress ripple without adding excessive loop inductance, and its stability effect must be included in closed-loop evaluation because changes near a power amplifier can alter output-pole behavior.
合规信息
The manufacturer datasheet and distributor listings do not explicitly establish the requested compliance status. No automotive qualification is claimed for this through-hole power operational amplifier.