Products (44,000+)

LPC2106FHN48 - 60MHz ARM7 MCU, 128KB Flash | NXP
LPC2106FHN48

LPC2106FHN48 - 60MHz ARM7 MCU, 128KB Flash | NXP

NXP Semiconductors LPC2106FHN48 is a 32-bit ARM7TDMI-S microcontroller with a 60 MHz CPU, 128 kB of embedded ISP/IAP flash memory, and 64 kB of RAM in a 48-pin HVQFN package measuring 7 x 7 mm. It integrates two UARTs, I2C, SPI, 32 general-purpose I/O ports, timers, and an ARM7TDMI-S core with real-time emulation and embedded trace support. A microcontroller is a programmable semiconductor that combines a CPU core, memory, and peripheral interfaces on one integrated circuit. Within the embedded-device hierarchy, the LPC2106 belongs to the 32-bit microcontroller category and uses an ARM7 architecture rather than an 8- or 16-bit processor architecture. Its combination of embedded flash, RAM, serial interfaces, and deterministic control peripherals makes it suitable for compact embedded control and communication systems. The LPC2106FHN48 provides 128 kB of high-speed embedded flash for program storage and 64 kB of RAM for working memory. Two UART interfaces support serial data exchange, while I2C and SPI expand the device's connection to sensors, converters, transceivers, and external nonvolatile storage. Its 32 I/O ports provide parallel digital connectivity for control signals, status indicators, and external logic. The ARM7TDMI-S processor includes real-time emulation and embedded trace capabilities, allowing developers to observe execution behavior during firmware development. Its 60 MHz operating frequency supports interrupt-driven control loops and protocol handling without requiring a separate CPU. Depending on the ordering suffix, the operating-temperature qualification may differ; confirm the exact suffix before beginning a production design. Typical applications include industrial monitoring equipment, building-control modules, serial gateways, data loggers, instrument interfaces, and embedded communications controllers. The two UARTs can connect the MCU to host processors or external modems, while SPI and I2C suit higher-speed peripherals and low-speed sensors. The 7 x 7 mm package also supports compact control boards where board area is constrained. PCB implementation should preserve the manufacturer's recommended power, decoupling, clock, and exposed-pad connections. The 48-pin HVQFN footprint requires careful assembly planning and thermal-pad soldering to achieve reliable electrical and thermal performance. Use the LPC2104, LPC2105, and LPC2106 datasheet when validating pin assignments, startup behavior, and peripheral multiplexing. This product page combines the manufacturer architecture and ordering information with practical selection guidance, package details, application context, and a structured review of same-family drop-in alternatives. It is intended to help engineers determine whether the LPC2106FHN48 fits the required memory, interface, package, and environmental constraints before layout and firmware development.

RFQ Contact
LPC2106FHN48/01 - 60MHz ARM7 MCU, 128KB Flash | NXP
LPC2106FHN48/01

LPC2106FHN48/01 - 60MHz ARM7 MCU, 128KB Flash | NXP

NXP Semiconductors LPC2106FHN48/01 is a 32-bit ARM7TDMI-S microcontroller with a 60 MHz maximum clock, 128 KB of embedded high-speed ISP/IAP flash memory, and 64 KB of RAM in a 48-HVQFN package. It is designed for embedded applications requiring deterministic control, serial communications, and a compact surface-mount footprint. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and I/O on one device. The LPC2106 belongs to the general-purpose MCU hierarchy and uses the ARM7TDMI-S architecture, which supports 32-bit ARM instruction execution and 16-bit Thumb code. This combination provides broad software compatibility while allowing reduced code size where instruction density matters. The principal features of the LPC2106FHN48/01 include 128 KB of ISP/IAP flash, 64 KB of SRAM, a 60 MHz operating frequency, two UARTs, I2C, and SPI interfaces. A 128-bit-wide memory interface and accelerator architecture support efficient 32-bit code execution. Thumb mode can reduce code size by more than 30% relative to equivalent 32-bit instruction encoding, making the device suitable for firmware with limited flash capacity. The /01 suffix identifies a specific device configuration within the LPC2104, LPC2105, and LPC2106 family. NXP states that the family datasheet covers devices with and without /00 and /01 suffixes and that suffixes differentiate configurations containing new features. Firmware and hardware requirements should therefore be checked against the exact ordering code and datasheet before substitution. Typical uses include industrial control equipment, serial gateways, embedded data recorders, communications equipment, and compact control panels. The UARTs support asynchronous serial links, while I2C and SPI allow connection to sensors, memories, transceivers, and display or interface devices. The 60 MHz ARM7TDMI-S core is useful when deterministic response and moderate arithmetic processing are required without a higher-complexity Cortex-M device. PCB implementation requires careful attention to the 48-HVQFN land pattern, 0.50 mm terminal pitch, exposed thermal pad, and required power and decoupling connections. Use the manufacturer pin description table and package drawing when assigning tracks. Keep high-current supply paths short, connect the thermal pad to the intended ground plane, and provide local bypass capacitance at the supply pins. This product record combines the exact manufacturer ordering information with a practical comparison of verified family variants. It highlights where engineers must confirm electrical differences, pin compatibility, lifecycle status, and package details before approving any replacement or redesign.

RFQ Contact
LPC2114FBD64 - 60MHz ARM7 MCU 128KB Flash | NXP
LPC2114FBD64

LPC2114FBD64 - 60MHz ARM7 MCU 128KB Flash | NXP

NXP Semiconductors LPC2114FBD64 is a 16/32-bit ARM7TDMI-S microcontroller with a maximum clock frequency of 60 MHz, 128 KB of embedded high-speed flash memory, and a 64-LQFP package measuring 10 mm by 10 mm. It is designed for embedded control applications requiring integrated flash, serial interfaces, timing, and analog-to-digital conversion. The LPC2114FBD64 is part of the LPC2000 family of single-chip microcontrollers. An ARM7TDMI-S microcontroller is a 32-bit embedded processor core that can execute ARM or 16-bit Thumb instructions. The LPC2000 family combines that processor with memory, peripheral peripherals, interrupt handling, and communication interfaces in one package. The 128-bit wide memory interface and accelerator architecture support efficient 32-bit code execution, while Thumb mode can reduce code size for applications where memory density is important. The LPC2114/2124 family provides 128 KB or 256 KB of embedded high-speed ISP/IAP flash, depending on the selected device. The LPC2114FBD64 is identified with 128 KB of flash in the manufacturer product listing and distributor documentation. The device also includes a 10-bit ADC, programmable I/O, PWM capability, and serial peripherals suited to industrial control, communications, consumer equipment, and general-purpose embedded products. The 64-LQFP package provides 64 external leads and a compact surface-mount footprint. Its 10 mm by 10 mm body size supports conventional automated PCB assembly while leaving more routing space than many smaller leaded packages. The product family is based on an Arm7TDMI-S architecture with real-time emulation and embedded trace support, which assists development, debugging, and board bring-up. Typical uses include industrial controllers, data acquisition equipment, communication modules, embedded gateways, motor and power-control systems, and consumer products. The integrated ADC and PWM outputs reduce the number of external devices required for sensing and actuator control, while flash memory allows firmware, boot software, and application code to reside on the MCU. For PCB implementation, confirm the exact pin assignments, power rails, decoupling requirements, crystal or oscillator connections, programming interface, and exposed-pad or thermal requirements against the manufacturer datasheet. Use the package-specific land pattern and keep high-current supply paths compact. Firmware migration should also account for memory size, peripheral variants, oscillator configuration, and any differences in speed grade. This product summary combines the manufacturer’s LPC2114FBD64 information with distributor technical listings, package details, and practical implementation guidance for engineers evaluating legacy embedded-control designs.

RFQ Contact
LPC2119FBD64 - 60MHz ARM7 MCU, 128KB Flash | NXP
LPC2119FBD64

LPC2119FBD64 - 60MHz ARM7 MCU, 128KB Flash | NXP

NXP Semiconductors LPC2119FBD64 is a 16/32-bit Arm7TDMI-S microcontroller with a 60 MHz maximum clock, 128 KB of embedded high-speed flash memory, 16 KB of SRAM, and a 64-LQFP 10 x 10 mm package. The device combines a 128-bit-wide memory interface, a unique accelerator architecture, 46 I/O lines, a 10-bit ADC, and CAN connectivity for compact embedded control designs. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface logic on one device. The LPC2100 family belongs to the broader hierarchy of microcontrollers, embedded processors, and embedded semiconductors. It targets applications requiring deterministic control, serial communications, data acquisition, and local real-time processing while keeping component count and board area low. The LPC2119FBD64 is differentiated by its Arm7TDMI-S core, which supports both 32-bit ARM state and 16-bit Thumb state. Thumb mode can reduce code size for constrained applications, while the 32-bit instruction set remains available for higher-performance routines. Its 128-bit memory interface and accelerator architecture support efficient 32-bit execution at the maximum clock rate. Embedded flash also permits in-system programming and in-application programming. Peripheral integration is important in embedded systems because it reduces external component requirements. The LPC2119 includes a 10-bit ADC, CAN interface, real-time emulation, embedded trace support, and boundary-scan capability. These features support acquisition, industrial networking, production test, and debug workflows. The manufacturer also documents 64, 128, and 256 KB flash configurations across the LPC2109, LPC2119, and LPC2129 family, with the LPC2119 position corresponding to 128 KB. Typical uses include industrial control equipment, CAN-connected modules, data loggers, motor and process controllers, and compact embedded platforms requiring 46 GPIO. The 64-LQFP package offers a practical pin count for a mixed-signal controller while keeping the die exposed through a conventional surface-mount footprint. Board design should preserve the controller's power, decoupling, clock, reset, and programming requirements from the manufacturer datasheet. CAN routing also requires controlled impedance and appropriate termination strategy. Because the public product material does not reproduce the complete pin-description table, use the official LPC2119 documentation when assigning tracks and connector functions. This product page combines the official NXP device description with package, memory, connectivity, lifecycle, sourcing, replacement, and engineering guidance. It also distinguishes order-code alternatives from genuinely independent drop-in substitutes, helping engineers make a PCB-safe replacement decision rather than assuming that similar specifications guarantee pin compatibility.

RFQ Contact
LPC2124FBD64 - 60MHz ARM7TDMI-S MCU | NXP Semiconductors
LPC2124FBD64

LPC2124FBD64 - 60MHz ARM7TDMI-S MCU | NXP Semiconductors

NXP Semiconductors LPC2124FBD64 is a 16/32-bit Arm7TDMI-S microcontroller with a maximum clock frequency of 60 MHz, 256 KB of embedded high-speed flash memory, 16 KB of SRAM, and 46 general-purpose I/O lines in a 64-pin LQFP package. It combines a 128-bit memory interface with an accelerator architecture designed to support 32-bit code execution at the maximum clock rate. A microcontroller is a programmable semiconductor device that integrates a processor core, memory, and peripherals into one package. The LPC2124 belongs to the Arm7TDMI-S embedded-control hierarchy, combining deterministic real-time execution with in-system programming, in-application programming, analog conversion, timers, serial interfaces, and general-purpose I/O. This makes it suitable for industrial controllers, embedded data acquisition, communications equipment, and real-time monitoring systems. The LPC2124FBD64 provides 256 KB of flash for firmware and 16 KB of SRAM for working data. Its 10-bit ADC supports analog measurement functions, while 46 GPIO pins provide flexible connections to sensors, actuators, displays, and communication transceivers. The 60 MHz Arm7TDMI-S core supports 32-bit instruction execution, and the accelerator architecture improves performance on suitable memory-intensive operations. The device uses a 3.3 V CMOS supply according to the manufacturer product information. The LQFP-64 package has a 0.50 mm terminal pitch and is suitable for conventional surface-mount PCB assembly. Its documented operating-temperature range for the LPC2124FBD64/00,15 ordering variant is -40 °C to +85 °C. The manufacturer identifies the family as supporting real-time emulation and embedded trace functions. Typical applications include industrial automation controllers, serial-protocol gateways, data-acquisition units, motor and process-control systems, and communications equipment. The combination of 256 KB flash, 16 KB SRAM, 46 I/O lines, and a 10-bit ADC supports compact embedded designs requiring both digital control and analog measurement. For PCB implementation, assign the power, ground, reset, clock, and programming signals according to the manufacturer pin-description table in the LPC2124 datasheet. Place decoupling capacitors close to the supply pins and preserve the required signal-routing geometry around the 64-pin LQFP footprint. Firmware changes should follow the manufacturer’s ISP/IAP and flash-programming procedure rather than relying on undocumented bootloader behavior. This page consolidates the manufacturer specifications, package information, ordering variants, and design guidance needed to evaluate the LPC2124FBD64, compare same-footprint family alternatives, and plan an embedded-controller board without duplicating the raw datasheet organization.

RFQ Contact
LPC2129FBD64 - 60MHz ARM7 MCU with 256KB Flash | NXP
LPC2129FBD64

LPC2129FBD64 - 60MHz ARM7 MCU with 256KB Flash | NXP

NXP LPC2129FBD64 is a 16/32-bit Arm7TDMI-S microcontroller with a 60 MHz maximum clock frequency, 256 KB of embedded flash memory, and a 64-LQFP 10 x 10 mm package. It integrates ISP/IAP programming, a 10-bit ADC, CAN connectivity, real-time emulation, and embedded trace support. These characteristics position the device as a compact embedded-control platform for industrial communications, data acquisition, and CAN-connected equipment. An Arm7TDMI-S microcontroller combines a 32-bit ARM processor core with 16-bit Thumb instruction support. The LPC2129 family belongs to the broader hierarchy of Arm microcontrollers, embedded processors, and integrated circuits designed for real-time control. Its 128-bit memory interface and accelerator architecture support efficient 32-bit execution, while Thumb mode can reduce code footprint when memory capacity is constrained. The 256 KB embedded high-speed flash provides dedicated program storage without an external memory device. ISP and IAP capabilities support programming and field-update workflows, while the integrated 10-bit ADC supports analog measurement and threshold-based control. CAN support is valuable for industrial networking, and boundary-scan functionality assists board-level validation. Real-time emulation and embedded trace improve debugging visibility for control-loop and communication diagnostics. The 64-LQFP package uses a 0.5 mm terminal pitch and is designed for surface mounting. Its 10 x 10 mm body offers substantially more board area than smaller leadless packages while retaining through-board inspection visibility. The LPC2129's 60 MHz Arm7TDMI-S core is suitable for protocol processing, supervisory control, sensor interfaces, and embedded CAN nodes that do not require the software ecosystem of a newer Cortex-M MCU. Typical applications include industrial CAN gateways, motor and machine controllers, building automation modules, data loggers, test equipment, and embedded instrumentation. The combination of on-chip flash, ADC, CAN, and debug support reduces external component count and simplifies firmware deployment where field programming and deterministic peripheral access are important. Designers should confirm pin-level multiplexing, regulator tolerances, peripheral availability, and memory mapping against the NXP datasheet. Crystal and decoupling layouts should follow the manufacturer's reference configuration. Firmware migration should also verify startup code, bootloader behavior, and peripheral-driver compatibility because ARM7 and Cortex-M products use different exception and interrupt architectures. This page consolidates the NXP product information, ordering variants, drop-in compatibility guidance, application guidance, and design considerations into one engineering-focused reference for selecting and implementing the LPC2129FBD64.

RFQ Contact
LPC2131FBD64 - 60MHz ARM7 MCU, 32KB Flash | NXP
LPC2131FBD64

LPC2131FBD64 - 60MHz ARM7 MCU, 32KB Flash | NXP

The NXP Semiconductors LPC2131FBD64 is a 16/32-bit ARM7TDMI-S microcontroller operating at 60 MHz, with 32 KB of embedded flash memory and a 64-pin LQFP package measuring 10 x 10 mm. It integrates 8 KB of SRAM, a 10-bit ADC, a DAC, GPIO, PWM, and serial peripherals for compact embedded-control designs. The LPC2131FBD64 is suitable for industrial controllers, data-acquisition equipment, communications modules, and legacy ARM7 system upgrades. An ARM7TDMI-S microcontroller is a 32-bit RISC device that combines a conventional processor core, embedded program memory, and dedicated peripherals in one integrated circuit. Its position in the product hierarchy is microcontroller, then 32-bit RISC microcontroller, then ARM7TDMI-S embedded controller. The architecture supports 32-bit code execution while retaining deterministic interrupt-driven operation for real-time control workloads. Principal features include a 60 MHz maximum clock, 32 KB of embedded high-speed flash, 8 KB of SRAM, a 10-bit ADC, an on-chip DAC, PWM outputs, and multiple GPIO. The 128-bit memory interface and accelerator architecture improve instruction throughput. In-System Programming and In-Application Programming support add manufacturing and field-update flexibility without removing the microcontroller from its target circuit. The LPC2131/32/34/36/38 family uses a common hardware platform across several flash configurations. The 32 KB version has lower on-chip memory than the 64, 128, 256, and 512 KB family members, but retains the same 60 MHz ARM7TDMI-S core and 64-pin LQFP footprint. This makes the LPC2131FBD64 appropriate for compact code where external memory would otherwise increase cost and board area. Typical applications include industrial data loggers, serial protocol converters, motor and process controllers, test equipment, and communications gateways. Its mixed-signal peripherals allow an analog sensor interface and digital control logic to share one device, while PWM and capture functions support actuator monitoring and timing tasks. When designing around the LPC2131FBD64, check every peripheral pin against the selected board variant and provide the decoupling and oscillator arrangements shown in the manufacturer datasheet. Because this is an established ARM7 design, confirm that current toolchain, library, and driver support covers the exact firmware and production requirements before committing to a new design. This page consolidates core specifications, ordering variants, comparison data, and practical design guidance. It also documents where package-level verification and datasheet pin descriptions should be used, helping engineers evaluate the LPC2131FBD64 without relying on generic microcontroller recommendations.

RFQ Contact
LPC2131FBD64/01 - 60MHz 32KB ARM7 MCU | NXP
LPC2131FBD64/01

LPC2131FBD64/01 - 60MHz 32KB ARM7 MCU | NXP

The NXP Semiconductors LPC2131FBD64/01 is a 16/32-bit Arm7TDMI-S microcontroller with a 60 MHz maximum clock, 32 KB of embedded flash memory, and a 64-LQFP 10 x 10 mm package. It combines an embedded single-chip microcontroller, serial interfaces, 10-bit analog conversion functions, and real-time emulation and embedded trace support in one compact surface-mount device. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripheral functions into a single integrated circuit. The LPC2131 belongs to the LPC2100 family of Arm7-based embedded control devices. Its position in the hierarchy is microcontroller, embedded processor, programmable controller, and semiconductor. This integration allows equipment manufacturers to consolidate control, communications, data acquisition, and actuator-driving functions onto one board. Principal features include a 16/32-bit Arm7TDMI-S core operating up to 60 MHz, 32 KB of high-speed embedded flash, a 10-bit ADC and DAC, and 46 I/O ports as listed for the LPC2131FBD64/01. The device is intended for industrial-temperature operation and is supplied in a 64-pin LQFP package measuring 10 x 10 mm with a stated height of 1.40 mm. The Arm7TDMI-S architecture supports real-time emulation and embedded trace, providing designers with visibility into execution behavior during firmware development and system diagnostics. Embedded flash permits the operating firmware, configuration data, and application code to reside in the same package. The serial interface resources and analog peripherals make the device suitable for connected industrial controllers, data-acquisition equipment, and embedded communications systems. Typical uses include industrial control panels, serial gateways, instrumentation, data loggers, and communication equipment. In these systems, the microcontroller can coordinate sensors, process data, drive outputs, and communicate with a host through its serial peripherals. Its 60 MHz processing capability provides useful headroom for protocol handling and supervisory control functions. Designers should preserve the power, decoupling, clock, and programming requirements specified by NXP. Pay particular attention to the 3.3 V supply arrangement identified for the LPC2131FBD64/01 and validate the final board against the manufacturer pin description and application guidance before production release. This page combines the manufacturer product information, family-level characteristics, and practical engineering guidance to support component selection, firmware planning, PCB design, sourcing, and replacement assessment for the LPC2131FBD64/01.

RFQ Contact
LPC2132FBD64 - 60MHz ARM7 MCU, 64KB Flash, LQFP-64 | NXP
LPC2132FBD64

LPC2132FBD64 - 60MHz ARM7 MCU, 64KB Flash, LQFP-64 | NXP

The NXP Semiconductors LPC2132FBD64 is a single-chip 16/32-bit ARM7TDMI-S microcontroller operating at up to 60MHz, with 64KB of embedded flash memory and 16KB of SRAM in a 64-pin LQFP package measuring 10mm by 10mm. It integrates a 10-bit ADC and DAC, providing a compact platform for embedded control, data acquisition and mixed-signal applications. An ARM7TDMI-S microcontroller combines a 32-bit ARM processor core with embedded real-time emulation and trace support. Within the embedded-device hierarchy, the LPC2132FBD64 belongs to the NXP LPC2000 general-purpose MCU family, combining processor core, nonvolatile program memory, static RAM, analog conversion and serial interfaces in one package. This integration reduces external component count while retaining dedicated hardware for embedded control. Key features include an ARM7TDMI-S 16/32-bit core, a maximum clock frequency of 60MHz, 64KB flash, 16KB SRAM, 10-bit ADC and 10-bit DAC functions, and a 64-pin LQFP package. Its 128-bit memory interface and accelerator architecture support efficient 32-bit instruction execution at the maximum operating frequency, according to the NXP LPC2000 family description. The LPC2132FBD64 is suited to designs requiring deterministic embedded control, mixed-signal measurement and multiple communication interfaces. Typical uses include industrial data-acquisition controllers, networked monitoring equipment, building-control modules, instrument-control systems and compact embedded gateways. The integrated converters allow an analog sensor to be digitized and a control or reference signal to be generated without adding separate converter packages. PCB design should preserve short analog traces, provide clean grounding around the ADC and DAC circuitry, and follow the manufacturer pin and layout guidance for the 64-pin LQFP footprint. Firmware should use the LPC2132 memory map and ARM7TDMI-S startup sequence, while application code should account for the device's 64KB flash and 16KB SRAM limits during linker allocation. This page combines the exact NXP and distributor identity, package and memory characteristics with application guidance, a parameter comparison, and actionable replacement criteria. The LPC2132FBD64 is best suited to legacy or ongoing ARM7-based designs that need a 60MHz controller, 64KB embedded flash and integrated 10-bit analog conversion in an established 64-LQFP footprint.

RFQ Contact
LPC2132FBD64/01151 - ARM7 64KB Flash MCU | NXP 64-LQFP
LPC2132FBD64/01151

LPC2132FBD64/01151 - ARM7 64KB Flash MCU | NXP 64-LQFP

The NXP LPC2132FBD64/01151 is a 16/32-bit ARM7TDMI-S microcontroller with 64 KB of embedded high-speed flash memory, 16 KB SRAM, and a rich set of peripherals, housed in a 64-pin LQFP (10x10 mm) package. It integrates a 10-bit ADC, 10-bit DAC, two 32-bit timers, a watchdog timer, real-time clock, USB 2.0 full-speed device controller, and multiple serial interfaces (UART, SPI, I2C). Key specifications include a 60 MHz maximum CPU clock from the on-chip PLL, 128-bit wide memory interface with a unique accelerator enabling 32-bit code execution at maximum clock rate, single 3.3 V power supply operation, and on-chip integrated oscillator. The MCU targets embedded control, industrial networking, and USB device applications where deterministic real-time behavior is required. The LPC2132 belongs to the LPC2131/32/34/36/38 family which scales flash memory from 32 KB to 512 KB. Its 64 KB flash and 16 KB SRAM position it as a mid-density member of the family, suitable for applications requiring modest program and data memory plus USB connectivity. The peripheral mix (USB, ADC, DAC, RTC, multiple timers) provides a complete system-on-chip solution for industrial, medical, and consumer products. Typical applications include industrial control and automation, USB peripherals and bridges, point-of-sale terminals, medical instrumentation, smart card readers, and general embedded control. The on-chip USB 2.0 full-speed device controller simplifies USB device designs by eliminating external PHY and reducing BOM cost. When designing with this device, ensure the JTAG and Embedded Trace Macrocell (ETM) debug access is preserved for development and field updates; the ARM7TDMI-S supports both real-time emulation and embedded trace. ISP/IAP flash programming via UART enables in-system firmware updates without removing the part from board-level access. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes for the LPC2132FBD64/01151 that are not found in the manufacturer datasheet, enabling engineers to make faster component selection decisions.

RFQ Contact
LPC2134FBD64 - 60MHz ARM7 128KB Flash MCU | NXP
LPC2134FBD64

LPC2134FBD64 - 60MHz ARM7 128KB Flash MCU | NXP

The NXP Semiconductors LPC2134FBD64 is a single-chip 16/32-bit ARM7TDMI-S microcontroller with a 60 MHz maximum clock, 128 kB of embedded flash, 16 kB of SRAM, 10-bit ADC and DAC peripherals, and a 64-LQFP surface-mount package. It combines a 32-bit ARM7TDMI-S core with a 128-bit-wide memory interface and accelerator architecture for high-speed 32-bit code execution. A microcontroller is a programmable integrated circuit that consolidates a processor core, memory, and peripherals into one component. The LPC2134 belongs to the ARM7 MCU family and sits within the broader hierarchy of embedded processor, microcontroller, and semiconductor control devices. Its on-chip flash supports in-system programming and in-application programming, while its serial interfaces, timers, and analog converters provide a practical platform for embedded control without requiring substantial external memory. Key features include a 60 MHz operating clock, 128 kB of embedded high-speed flash, 16 kB of SRAM, and 10-bit ADC and DAC channels. The 64-LQFP package is specified as a 10 mm by 10 mm surface-mount device with a 0.5 mm terminal pitch. The device supports operating temperatures from -40 °C to +85 °C, making it suitable for industrial, automation, and embedded control environments where extended-temperature operation is required. The ARM7TDMI-S architecture provides real-time emulation and embedded trace support for development and debugging. The wide memory interface and accelerator architecture are intended to maintain execution performance at the maximum clock rate, while the integrated analog converters reduce the need for external components in measurement and control systems. Typical applications include industrial automation equipment, motor and motion controllers, data acquisition modules, communications interfaces, and embedded instruments. The 10-bit ADC supports analog sensor monitoring, while the DAC supports setpoint generation, waveform control, and analog output functions. When designing a PCB around the LPC2134FBD64, preserve the 0.5 mm LQFP pitch, provide stable decoupling near the supply pins, and route the crystal and high-speed signals according to the pin-description and layout guidance in the NXP datasheet. This page combines the manufacturer specifications, family alternatives, and application guidance to help engineers evaluate the device for new and legacy embedded designs.

RFQ Contact
LPC2141FBD64 - 60MHz ARM7 MCU, 32KB Flash | NXP
LPC2141FBD64

LPC2141FBD64 - 60MHz ARM7 MCU, 32KB Flash | NXP

NXP Semiconductors LPC2141FBD64 is an ARM7TDMI-S 16/32-bit microcontroller operating up to 60 MHz, with 32 KB of on-chip flash and 8 KB of SRAM in a 64-LQFP package. The device combines a 32-bit ARM7TDMI-S processor, USB 2.0 full-speed device support, serial interfaces, timers, and 10-bit analog conversion resources for embedded control systems. An ARM7-based microcontroller is a single-chip processing platform that executes 32-bit instructions while supporting the wider ARM instruction set and embedded peripherals required for control applications. Within the product hierarchy, the LPC2141FBD64 is a microcontroller, or MCU, integrating a CPU core, memory, communication interfaces, timers, and analog peripherals on one integrated circuit. The LPC2141FBD64 provides 32 KB of flash for program storage, 8 KB of SRAM for working memory, and a maximum CPU frequency of 60 MHz. Its USB 2.0 full-speed device interface supports direct USB connectivity, while the family also includes 10-bit ADC and DAC functions. The 64-LQFP package provides 64 terminals for external memory, communications, analog, timing, and control connections. The ARM7TDMI-S architecture uses a 128-bit memory interface and an accelerator architecture intended to support maximum-rate 32-bit code execution. Real-time emulation and embedded trace support assist development and diagnostics. Multiple peripheral functions can share pins through configurable multiplexing, allowing designers to balance USB, serial communications, timers, analog inputs, and external memory interfaces against board-space constraints. Typical implementations include USB-connected data acquisition equipment, industrial control modules, USB-to-serial or USB-to-protocol adapters, embedded test instruments, and legacy peripheral controllers. The device is especially relevant to systems that retain an ARM7 software base and require a compact LQFP footprint while adding a full-speed USB device interface. Hardware design should begin with the manufacturer pin connection table and power requirements for the selected clock and peripheral configuration. Place decoupling capacitors close to the supply terminals, route USB data pairs as a controlled-impedance differential pair, and keep analog and high-current switching paths separated from sensitive signal pins. Firmware must configure pin multiplexing, clocks, and peripheral ownership before enabling the corresponding external functions. This product record combines the manufacturer family specification with package, interface, memory, and sourcing details. It also provides drop-in family comparisons and application-oriented guidance covering USB connectivity, embedded control, data acquisition, and industrial equipment, helping engineers evaluate the LPC2141FBD64 without relying on a basic catalog summary alone.

RFQ Contact
LPC2142FBD64 - 60MHz ARM7 64KB Flash MCU | NXP
LPC2142FBD64

LPC2142FBD64 - 60MHz ARM7 64KB Flash MCU | NXP

NXP LPC2142FBD64 is a single-chip 16-bit/32-bit ARM7TDMI-S microcontroller operating up to 60 MHz, with 64 KB of embedded flash and 16 KB of SRAM in a 64-LQFP package measuring 10 x 10 mm. The device integrates USB 2.0 full-speed device connectivity, a 10-bit ADC, a 10-bit DAC, In-System Programming, and In-Application Programming. An ARM7TDMI-S microcontroller is a 32-bit embedded processor that combines an ARM processing core, memory, and peripherals in a single integrated circuit. The LPC2100 family hierarchy places the LPC2142 in the embedded microcontroller segment, where a high-performance CPU, deterministic peripherals, and flexible in-circuit programming support industrial control, communications, and data-acquisition equipment. The principal characteristics are a 60 MHz ARM7TDMI-S core, 64 KB of program flash, and 16 KB of SRAM. A 128-bit memory interface and accelerator architecture support 32-bit code execution at the maximum clock rate. Real-time emulation and embedded trace support improve debugging visibility, while ISP and IAP simplify firmware programming and field updates. Integrated USB 2.0 full-speed device support makes the LPC2142FBD64 suitable for USB-connected control, data acquisition, and peripheral products. The on-chip 10-bit ADC and DAC support analog measurement and signal generation without requiring separate converters. Together, these resources allow a compact design to combine acquisition, processing, communications, and control in a single microcontroller package. Typical uses include industrial data loggers, USB interface controllers, instrumentation, embedded test equipment, communications modules, and control systems. The 60 MHz processing rate and 64 KB flash capacity are well matched to protocol handling, supervisory logic, and mixed analog-digital control. Designs requiring more program storage should be assessed against the larger-memory members of the LPC214x family. PCB implementation should preserve short analog and digital return paths, route high-current supply connections with adequate copper, and place decoupling capacitors close to the power pins. USB differential routing requires controlled impedance and minimized stub length. Firmware configuration, peripheral clocks, and unused pins should be initialized according to the manufacturer datasheet before production release. This page combines the manufacturer family data with practical package, programming, interface, and replacement guidance. It distinguishes the exact LPC2142FBD64 configuration from related ordering codes and explains when a higher-memory family member may be appropriate for a redesigned board.

RFQ Contact
LPC2144FBD64 - 60MHz ARM7 MCU, 128KB Flash | NXP
LPC2144FBD64

LPC2144FBD64 - 60MHz ARM7 MCU, 128KB Flash | NXP

The NXP LPC2144FBD64 is a 16-bit/32-bit ARM7TDMI-S microcontroller operating at up to 60 MHz, with 128 KB of embedded flash memory, 16 KB of SRAM, USB 2.0 full-speed device support, and 10-bit ADC and DAC peripherals in a 64-LQFP 10 x 10 mm package. It combines deterministic 32-bit execution with integrated connectivity and mixed-signal peripherals for compact embedded-control designs. An ARM7 microcontroller is a member of the embedded-processor hierarchy that combines a CPU core, memory, peripherals, and I/O within one integrated circuit. The LPC2144FBD64 belongs to the NXP LPC2100 family and uses the ARM7TDMI-S core with a 128-bit memory interface and accelerator architecture for 32-bit code execution at the maximum clock rate. Its principal features include a 60 MHz clock, 128 KB of high-speed embedded flash, 16 KB of SRAM, full-speed USB device operation, and 10-bit ADC and DAC channels. The integrated USB controller reduces external interface complexity, while the converter peripherals support industrial measurement, control, and low-resolution analog signal generation without requiring separate analog devices. The architecture is suited to embedded systems that require higher processing capacity than an 8-bit controller while retaining a conventional integrated peripheral set. Embedded trace and real-time emulation support assist development and diagnostics, while the unified memory architecture allows code, data, and firmware-upgrade operations to be managed within one programmable device. Typical uses include USB-connected data-acquisition equipment, industrial controllers, serial-interface products, embedded gateways, and compact control panels. The 60 MHz ARM7TDMI-S performance is appropriate for protocol handling, supervisory control, and multi-interface coordination, while the 10-bit ADC and DAC can reduce board area in cost-sensitive mixed-signal products. PCB implementation requires careful attention to the 64-LQFP pin geometry, power and ground distribution, clock stability, and analog signal routing. The USB interface and converter inputs are sensitive to return-path noise and inappropriate trace lengths, so separating analog and digital return currents helps preserve signal quality. This page consolidates the manufacturer specifications, package information, verified commercial availability, and design-oriented guidance for engineers evaluating the LPC2144FBD64. It also highlights the limits of a direct replacement search: an assembly with the same device family and package still requires firmware, memory-map, peripheral, and software-tool compatibility checks.

RFQ Contact
LPC2146FBD64 - 60MHz ARM7 Microcontroller with USB 2.0 | NXP
LPC2146FBD64

LPC2146FBD64 - 60MHz ARM7 Microcontroller with USB 2.0 | NXP

The NXP Semiconductors LPC2146FBD64 is a single-chip 16-bit/32-bit ARM7TDMI-S microcontroller operating up to 60MHz, with 256KB flash, ISP/IAP support, USB 2.0 full-speed device connectivity, and 10-bit ADC and DAC functions in a 64-LQFP package. It combines a high-performance ARM7 core with embedded high-speed flash and communications peripherals for embedded control, data acquisition, and USB-connected equipment. An ARM7 microcontroller is a 32-bit RISC processor platform designed for embedded systems, where deterministic control, peripheral integration, and low-power operation are more important than desktop-class computing. The LPC2146 belongs to the LPC2000 general-purpose MCU family, using the ARM7TDMI-S architecture with real-time emulation and embedded trace support. This hierarchy places it within microcontrollers, embedded processors, and semiconductor-based control systems. Key features visible in the verified product data include a 60MHz operating frequency, 256KB of flash memory, USB 2.0 full-speed device operation, and integrated 10-bit ADC and DAC peripherals. ISP/IAP capability supports programming and application updates, while the 128-bit memory interface and accelerator architecture described by NXP are intended to improve execution efficiency for 32-bit code. These characteristics suit systems requiring local control, mixed-signal measurement, and USB data exchange. Typical applications include USB data acquisition controllers, industrial monitoring equipment, communications interfaces, embedded test systems, and compact control platforms. The integrated converters reduce the need for separate analog support where their channel counts, reference, and electrical limits meet the system requirements. The ARM7TDMI-S core also supports established embedded development workflows and debugging ecosystems. When designing around the LPC2146FBD64, verify the complete electrical and pin-level requirements against the manufacturer datasheet, especially USB routing, analog input conditioning, clock configuration, decoupling, and programming interfaces. The 64-LQFP footprint requires careful land-pattern compliance and adequate clearance around adjacent signal pins. This product page combines verified NXP specifications, distributor availability signals, package information, and engineering-oriented selection guidance. It distinguishes documented facts from parameters requiring confirmation, helping engineers evaluate the LPC2146FBD64 for USB-enabled embedded control and analog acquisition designs.

RFQ Contact
LPC2148FBD64 - 60MHz ARM7 MCU with USB | NXP
LPC2148FBD64

LPC2148FBD64 - 60MHz ARM7 MCU with USB | NXP

The NXP Semiconductors LPC2148FBD64 is a 16-bit/32-bit ARM7TDMI-S microcontroller with a 60 MHz maximum clock, 512 kB of embedded flash, USB 2.0 full-speed device support, and 10-bit ADC and DAC peripherals in a 64-LQFP package measuring 10 mm by 10 mm. The part combines an ARM processor core, high-speed embedded memory, and mixed-signal connectivity in one device. An ARM7TDMI-S microcontroller is a single-chip embedded processing device designed to execute 16-bit or 32-bit instructions while integrating memory and peripherals. Within the product hierarchy, the LPC2148 belongs to the LPC2100 family of ARM7-based microcontrollers, combining real-time emulation, embedded trace support, and a 128-bit memory interface. It is intended for industrial control, communications, data acquisition, and USB-connected embedded systems. Key features include 512 kB of embedded flash, up to 40 kB of SRAM, a 60 MHz operating frequency, USB 2.0 full-speed device operation, and 10-bit ADC and DAC channels. The integrated converter resources reduce the need for external signal-conditioning and data-conversion components when the system must acquire analog inputs and generate analog outputs. The 64-LQFP package also provides enough perimeter pins for external memories, communications interfaces, and general-purpose I/O. The ARM7TDMI-S architecture supports efficient 32-bit execution while maintaining compatibility with 16-bit ARM code. Its 128-bit-wide memory interface is designed to support code execution at the maximum clock rate, and the embedded flash permits firmware, boot code, and application logic to reside directly on the microcontroller. For new hardware, software should be developed against the current NXP LPC2148 device support and peripheral libraries rather than assuming compatibility with unrelated ARM7 microcontrollers. Typical applications include industrial control panels, USB data loggers, instrumentation front ends, serial gateways, and embedded measurement systems. The USB interface is particularly useful for a compact peripheral that must exchange configuration or logged data with a host computer, while the ADC and DAC support direct analog monitoring and low-speed signal generation. Firmware and external circuitry still need appropriate protection for industrial noise and ground-potential differences. PCB layout should preserve short, continuous return paths for USB, analog grounds, and power connections. Place decoupling capacitors close to the supply pins, keep analog and digital return currents separated where possible, and follow the package and application guidance in the manufacturer datasheet. The LCD, Ethernet, and USB interfaces also require careful signal-integrity treatment if those optional functions are used. This product page combines the manufacturer specifications, package information, sourcing context, interface considerations, and honest replacement guidance for LPC2148FBD64. It also distinguishes verified pin-compatible options from related devices that require different firmware, package changes, or board redesign.

RFQ Contact
LPC2210FBD144/01 - ARM7TDMI-S 75MHz ROMless MCU 144-LQFP | NXP
LPC2210FBD144/01

LPC2210FBD144/01 - ARM7TDMI-S 75MHz ROMless MCU 144-LQFP | NXP

The NXP LPC2210FBD144/01 is a 16/32-bit ARM7TDMI-S microcontroller operating up to 75 MHz, supplied in a 144-pin LQFP package (20x20 mm) with no on-chip flash (ROMless) and an external memory interface. The /01 suffix differentiates the LPC2210 silicon revision from earlier revisions, applying to devices that include the 10-bit ADC and full external memory bus. The integrated ARM7TDMI-S core with real-time emulation and embedded trace support delivers up to 75 MIPS of processing, while the 16-bit Thumb mode reduces code size by more than 30% with minimal performance penalty for memory-constrained designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, peripherals, and I/O on one die. The LPC2210 belongs to the ARM7 family of microcontrollers, which falls under the broader hierarchy of microcontrollers -> embedded processors -> integrated circuits -> semiconductors. ROMless variants like the LPC2210 are designed for systems that require large external memories (SRAM, SDRAM, NOR flash) and deterministic boot behavior, common in industrial control, point-of-sale, and medical systems where code size exceeds what on-chip flash can offer. Key features include an 8-channel 10-bit ADC with conversion time as low as 2.44 us, four 32-bit timers with capture/compare, six PWM outputs, a Real-Time Clock (RTC) with separate power domain, two UARTs, two I2C buses, an SPI interface, and a USB 2.0 Full-Speed Device port. The device provides up to 76 GPIOs depending on bus configuration, nine external interrupt pins, and a 16-bit external memory controller supporting SRAM, ROM, NOR flash, and SDRAM. Operating voltage is 1.8V core / 3.3V I/O, with industrial temperature grade (-40C to +85C). Architecturally, the LPC2210 uses a von Neumann single-bus design with the ARM7TDMI-S core, a low-latency Vectored Interrupt Controller (VIC) supporting up to 32 vectored IRQ slots, and the AMBA AHB peripheral bus. The 10-bit successive-approximation ADC is augmented with on-chip op-amp buffering capability on some channels. The integrated PLL allows the device to run from a low-frequency crystal while generating the high-speed internal clock. Typical applications include industrial control and PLCs, medical instrumentation, point-of-sale terminals, access control, gateway and protocol converter designs, and embedded control where large external flash is required for firmware storage. The wide GPIO count and rich peripheral set also make it suitable for printer controllers and HVAC interfaces. When designing with the LPC2210FBD144/01, an external boot memory is mandatory because the device is ROMless - the vector fetch on reset is performed from external CS0. Ensure the external memory interface is correctly wired and that bus-cycle timing matches the chosen SRAM/SDRAM speed grade. Power-rail decoupling (100 nF + 10 uF near each supply pin) is required for clean ADC operation. This page synthesizes NXP datasheet parameters, distributor pricing, drop-in /01-suffix alternatives, and practical PCB design notes not consolidated in a single place elsewhere on the web.

RFQ Contact
LPC2292FET144/01 - 60MHz ARM7 MCU, 256KB Flash | NXP
LPC2292FET144/01

LPC2292FET144/01 - 60MHz ARM7 MCU, 256KB Flash | NXP

The NXP LPC2292FET144/01 is a 16/32-bit ARM7TDMI-S microcontroller with a 60 MHz maximum clock frequency, 256 KB of embedded flash memory, 16 KB of RAM, and a 144-TFBGA package measuring 12 mm by 12 mm. It also provides two CAN controllers, a 10-bit ADC, and an external memory interface, making it suitable for embedded networking, industrial control, and communications equipment. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The LPC2292 belongs to the ARM7 embedded-control hierarchy: ARM7TDMI-S CPU core, 32-bit microcontroller, embedded system controller, and general-purpose semiconductor. Its bus-oriented architecture and extensive peripheral set allow one device to supervise communications, analog measurement, and external storage or memory-intensive operations. The LPC2292FET144/01 combines a 128-bit-wide memory interface with a unique accelerator architecture that enables 32-bit code execution at the maximum clock rate. Its 256 KB ISP/IAP flash supports in-system and in-application programming, while real-time emulation and embedded trace features assist firmware development and diagnostics. Two CAN controllers are useful for industrial networking, vehicle electronics, and embedded systems requiring reliable multi-controller communication. The 10-bit ADC provides analog measurement capability without requiring a separate converter, and the external memory interface expands the design options available when an application needs additional memory or peripheral devices. These interfaces complement the 60 MHz processor and make the LPC2292 suitable for control systems that combine communications, data acquisition, and external signal processing in one compact package. Typical uses include industrial controllers, CAN-connected equipment, building automation, embedded gateways, and data-acquisition systems. The 144-TFBGA package supports compact designs but requires careful PCB layout and inspection because its fine-pitch ball grid has limited soldering visibility. Firmware development can use the processor's real-time emulation and embedded trace capabilities to reduce the complexity of board bring-up and runtime analysis. Careful power, decoupling, clock, and memory-interface design is essential for reliable operation. Place the required supply capacitors close to their associated pins, route high-current and sensitive signals appropriately, and follow the NXP datasheet's recommended PCB and pin-configuration guidance. The /00 and /01 device variants use an identical pin configuration, which simplifies board-level planning across those revisions. This product page consolidates the principal NXP device characteristics, practical integration guidance, exact-source availability information, and a focused comparison with compatible LPC2200-family devices. It also highlights where revision-specific ordering codes and detailed package pin descriptions must be checked in the manufacturer datasheet before a new PCB is released for production.

RFQ Contact
LPC2364FBD100K - 72MHz ARM7 MCU, 128KB Flash, Ethernet/USB/CAN | NXP
LPC2364FBD100K

LPC2364FBD100K - 72MHz ARM7 MCU, 128KB Flash, Ethernet/USB/CAN | NXP

The NXP LPC2364FBD100K is an ARM7 LPC2300-series 16-bit/32-bit microcontroller operating at 72 MHz with 128 KB of on-chip flash memory and 34 KB of SRAM, housed in a 100-pin LQFP (14 x 14 mm) gull-wing package rated for industrial temperature. It integrates an Ethernet MAC, a USB 2.0 device/host/OTG controller, two CAN channels, four UARTs and an 8-channel 10-bit ADC, making it a single-chip solution for networked embedded control equipment. A microcontroller (MCU) is a complete single-chip computer containing a CPU core, program memory, data memory and a set of on-chip peripherals. The LPC2364FBD100K is built around the ARM7TDMI-S core, an older 32-bit RISC architecture that executes 32-bit code through a 128-bit-wide memory interface and an accelerator structure, reaching the maximum clock rate while keeping interrupt latency predictable. In the taxonomy, an MCU is a microcontroller, a type of embedded processor, falling under semiconductors and integrated circuits. Key features of this part include 128 KB of flash for In-System Programming and In-Application Programming, 34 KB of SRAM, a 10 Mbit/100 Mbit-capable Ethernet MAC with dedicated DMA channels, USB 2.0 device, host and OTG operation, two CAN 2.0B controllers, three SSP/SPI channels, three I2C channels, an I2S interface, a 10-bit DAC, two PWM channels, four general-purpose timers and a general-purpose DMA controller. A 10-bit ADC with eight channels supports analog sensor front ends. The LPC2300 architecture separates the ARM7TDMI-S core from the peripherals, and the accelerator lets the core execute 32-bit code at full speed while the 128-bit memory bus sustains simultaneous instruction fetches and DMA transfers. The part accepts an external crystal or oscillator up to 72 MHz and supports PLL-based clock generation, with typical power consumption in the tens of milliwatts at active operation and far lower figures in sleep or power-down modes. Typical applications include industrial Ethernet data loggers and gateways, USB-to-CAN industrial bridges, networked PLC and HMI controller boards, motor and stepper control peripherals, building and access-control panels, and USB-connected test and measurement instruments. Any design needing simultaneous Ethernet, USB and CAN traffic on one chip benefits from integrating three protocol engines instead of adding discrete controllers. When laying out the board, keep the 25 MHz or 12 MHz crystal and its load capacitors within a few millimeters of pins OSC1 and OSC2, route the Ethernet magnetic-link and line transformer signals as a controlled-impedance differential pair, and place the Ethernet PHY and its 1.2 V core regulator close to the MCU. The LQFP-100 footprint has a fine 0.5 mm pitch, so confirm solder mask and paste stencil parameters before volume production. This page combines manufacturer specification data, distributor pricing structure, same-footprint drop-in alternatives from the LPC2300 family and cross-brand ARM Cortex-M equivalents, plus practical layout and design notes that go beyond the basic manufacturer datasheet listing.

RFQ Contact
LPC2364FET100 - ARM7 MCU 128kB Flash 72MHz | NXP TFBGA-100
LPC2364FET100

LPC2364FET100 - ARM7 MCU 128kB Flash 72MHz | NXP TFBGA-100

The NXP LPC2364FET100 is a 16/32-bit ARM7TDMI-S microcontroller operating at 72 MHz with 128 kB of embedded flash and 34 kB of SRAM, housed in a 100-ball TFBGA (9x9 mm) package. It integrates an Ethernet MAC, USB 2.0 full-speed Device/Host/OTG, two CAN channels, three SSP/SPI ports, three I2C buses, an I2S interface, an 8-channel 10-bit ADC and a single 10-bit DAC, plus a 4-channel general-purpose timer block and 70 user I/O pins. An ARM7 microcontroller (Advanced RISC Machine, 32-bit) is a low-power general-purpose MCU core widely deployed in embedded networking and industrial control. Within the NXP LPC2000 family hierarchy, it sits between simpler Cortex-M0/M3 devices and higher-end Cortex-M3/M4 parts, balancing deterministic real-time performance with rich on-chip peripherals. The ARM7TDMI-S core combines a 32-bit data path with a 16-bit Thumb instruction set, giving a useful trade-off between code density and computational throughput for legacy and cost-sensitive designs. Key features include 128 kB on-chip flash with ISP/IAP support, 34 kB SRAM, a 128-bit-wide memory interface and a unique accelerator architecture that lets 32-bit code execute at the maximum clock rate. The device supports single 3.3 V supply operation, four UARTs (one with full modem control), two CAN 2.0B channels, and an external memory controller for SRAM/Flash/ROM expansion. The integrated 10-bit ADC with eight input channels and 10-bit DAC remove the need for external data converters in many closed-loop control loops. Typical applications include industrial Ethernet gateways, CAN-based fieldbus nodes, building automation controllers, USB peripherals, and embedded Point-of-Sale terminals that benefit from the simultaneous availability of Ethernet + USB + CAN. The 70 I/O pins and external memory bus also suit legacy 8/16-bit peripheral expansion. The 72 MHz ARM7 core is more than adequate for protocol stacks (TCP/IP, CANopen, Modbus) where deterministic latency matters more than raw compute. Key design consideration: the LPC2364FET100 is a member of the legacy ARM7 family and is not pin-compatible with newer Cortex-M3 LPC1768/LPC1769 parts; firmware must be rebuilt for migration. Decoupling must follow the NXP reference design (100 nF + 10 µF bulk near each VDD/VSS pair) to keep the 128-bit wide memory interface clean at 72 MHz. This page synthesizes distributor pricing, drop-in alternatives within the LPC2364 family, and design notes not found in the manufacturer datasheet alone.

RFQ Contact
LPC2366FBD100K - 72MHz ARM7 MCU with Ethernet | NXP
LPC2366FBD100K

LPC2366FBD100K - 72MHz ARM7 MCU with Ethernet | NXP

NXP Semiconductors LPC2366FBD100K is an ARM7 16/32-bit embedded microcontroller operating at 72 MHz, with 256 KB of flash memory and up to 58 KB of SRAM in a 100-pin LQFP package. It integrates an Ethernet MAC, USB Device, Host and OTG support, a DMA controller, four UARTs, two CAN channels, three SSP/SPI interfaces, three I2C interfaces, and I2S. The device also includes an 8-channel 10-bit ADC, a 10-bit DAC, two PWM channels, and four general-purpose timers. An ARM7 microcontroller is a single-chip embedded processing component that combines a CPU core, program memory, data memory, and peripherals on one integrated circuit. The ARM7 family is part of the broader microcontroller hierarchy, where a microcontroller integrates a processor, memory, and dedicated I/O functions into a compact semiconductor intended for control-oriented products. The LPC2366FBD100K is designed for embedded systems requiring extensive communications and mixed-signal connectivity. Its 256 KB flash provides embedded program storage, while up to 58 KB of SRAM supports working data, buffers, protocol stacks, and Ethernet or USB traffic. Integrated Ethernet MAC, USB, and CAN connectivity can reduce the number of discrete interface devices required in a controller. The ARM7TDMI-S architecture combines a 16/32-bit instruction set with real-time emulation support. At 72 MHz, the processor provides substantially greater computational headroom than many earlier 8-bit or 16-bit controllers while retaining the deterministic behavior required by embedded applications. Hardware peripherals including DMA, UART, CAN, SSP/SPI, I2C, timers, PWM, ADC, and DAC distribute common workloads from the CPU. Typical uses include industrial Ethernet controllers, USB-to-serial gateways, CAN-based industrial nodes, data acquisition equipment, embedded networking appliances, and compact control systems. The combination of Ethernet, USB, CAN, serial interfaces, and analog conversion is particularly useful when a product needs multiple communication methods without relying on several companion microcontrollers. Board design should preserve the package pin assignments and provide the power, clock, reset, and decoupling requirements specified in the NXP manufacturer datasheet. Ethernet magnetics, USB protection, and high-speed signal routing require careful layout control. Firmware must also reserve the correct peripheral instances, pin multiplexing, interrupt priorities, and memory regions before enabling high-speed communication paths. This product page consolidates the manufacturer specifications, available ordering information, interface details, and engineering guidance for LPC2366FBD100K. It supports faster component identification and provides practical context for selecting the MCU, planning firmware resources, checking PCB requirements, and comparing same-footprint alternatives.

RFQ Contact
LPC2368FBD100 - ARM7 72MHz 512KB Flash MCU | NXP
LPC2368FBD100

LPC2368FBD100 - ARM7 72MHz 512KB Flash MCU | NXP

The NXP LPC2368FBD100 is an ARM7TDMI-S based 16/32-bit microcontroller for embedded applications featuring high integration and low power consumption at up to 72 MHz operation. According to the NXP product page, it integrates up to 512 kB of embedded high-speed flash memory, up to 58 kB of SRAM, an Ethernet MAC, USB 2.0 Device/Host/OTG, a 10-bit 8-channel ADC, a 10-bit DAC, two CAN channels, four UARTs, three SSP/SPI ports, three I2C buses, an I2S interface, two PWM timers, four general-purpose timers, and a DMA controller. An ARM7 microcontroller is a 32-bit RISC processor core that executes both the 32-bit ARM and the 16-bit Thumb instruction set, allowing code-density and performance trade-offs. The ARM7TDMI-S variant adds a hardware multiplier and embedded ICE debug logic. Within NXP's portfolio, the LPC2300 family sits at the top of the legacy LPC2000 ARM7 line, ahead of the smaller LPC2100 and LPC2200 series, and is itself succeeded by the Cortex-M3 based LPC1700 family. Peripherals are tightly integrated to minimize external components in industrial Ethernet, USB, and CAN nodes. The device operates from a single 3.0 V to 3.6 V supply, with I/O tolerant to 5 V, and is housed in a 100-pin LQFP (14 x 14 mm) package suitable for cost-sensitive 4-layer PCB layouts. Key features include 72 MHz maximum CPU clock with on-chip PLL, 32 kB SRAM usable as battery-backed retention, vectored interrupt controller for deterministic real-time response, and ISP/IAP in-application programming via UART or CAN. The Ethernet MAC supports 10/100 Mbps MII/RMII with full-duplex operation, while the USB 2.0 controller supports device, host, and OTG roles. The ADC delivers 400 ksps across 8 channels at 10-bit resolution, and the DAC is a 10-bit rail-to-rail converter suitable for waveform generation. Typical applications include industrial Ethernet gateways, building automation controllers, USB peripherals and embedded hosts, CAN-based automotive body modules, point-of-sale terminals, and small-scale motor-control boards. Designers choose the LPC2368FBD100 when ARM7 firmware, a wide peripheral mix, and 512 kB of on-chip flash are required without an external memory bus. When designing with this device, ensure the 3.3 V analog supply (V3A) is decoupled with at least 100 nF plus a 10 uF bulk, and isolate it from the digital 3.3 V plane to avoid ADC/DAC noise coupling. The VBAT domain supports RTC backup and 32 kB of retained SRAM; route a small lithium cell or supercap there to preserve RTC time across power cycles.

RFQ Contact
LPC2368FBD100K - 72MHz ARM7 MCU with Ethernet | NXP
LPC2368FBD100K

LPC2368FBD100K - 72MHz ARM7 MCU with Ethernet | NXP

NXP Semiconductors LPC2368FBD100K is a 16/32-bit ARM7TDMI-S microcontroller operating at 72 MHz, with 512 KB of embedded flash, 58 KB of SRAM, and a 100-lead LQFP package measuring 14 x 14 mm. The device integrates an Ethernet MAC, USB Device, Host and OTG controller, two CAN channels, SD/MMC support, four UARTs, three SSP/SPI interfaces, three I2C interfaces, I2S, eight 10-bit ADC channels, a 10-bit DAC, and two PWM blocks. These resources allow one microcontroller to control communications, data acquisition, storage, and real-time peripheral functions without requiring several discrete interface controllers. An ARM7 microcontroller is a 32-bit embedded processor that combines a CPU core, memory, interrupt handling, and programmable peripherals in one integrated circuit. The LPC2300 family belongs to the broader embedded-microcontroller and semiconductor hierarchy. In system terms, the LPC2368FBD100K can serve as the central real-time controller between sensors, communications equipment, human-interface circuits, and external storage. Its integration reduces component count while preserving dedicated hardware for Ethernet, USB, CAN, serial data, and analog measurement. The primary architectural advantage is the 72 MHz ARM7TDMI-S core paired with the LPC2300 accelerator and memory organization. The device provides 512 KB of flash for firmware and 58 KB of SRAM for working data, while a 128-bit-wide memory interface supports the CPU's maximum clock rate. An Ethernet MAC supports network-connected equipment, while USB Device, Host, and OTG operation broadens its role in host and peripheral designs. Two CAN channels suit industrial communication, and the DMA controller moves data with less CPU intervention. The integrated serial resources support several embedded architectures. Four UARTs can connect external sensors, service consoles, or industrial equipment; three SSP/SPI interfaces support fast serial peripherals; three I2C buses suit low-speed controllers and sensors; and I2S provides a dedicated path for digital audio data. The eight-channel 10-bit ADC handles analog inputs, the 10-bit DAC generates analog output, and two PWM blocks support timing, dimming, or motor-control functions. A 10-bit ADC is appropriate for supervisory measurement rather than precision instrumentation with substantially higher resolution requirements. Typical applications include industrial Ethernet gateways, USB-to-serial equipment, CAN-connected control systems, SD/MMC data loggers, audio-capable embedded controllers, and multi-interface test equipment. The Ethernet MAC, USB controller, and CAN channels allow the MCU to bridge communication technologies. The ADC and DAC support supervisory control loops, while SD/MMC connectivity supports removable or nonvolatile data storage. Firmware can also use the ISP and IAP capabilities associated with the LPC2364/65/66/67/68 family for in-system programming and application update workflows. A successful design must account for the 100-pin footprint, all peripheral pin multiplexing, power-supply sequencing, clock configuration, and the demands placed by simultaneous Ethernet, USB, CAN, and memory activity. The LQFP package provides accessible leads for assembly and inspection, but the high pin count requires careful fanout and signal-integrity planning. Firmware should configure each peripheral only after resolving its alternate-function pins and should verify the resulting pin muxing against the manufacturer pin-description table. This page consolidates the exact LPC2368FBD100K identity, verified memory and interface specifications, lifecycle information, sourcing guidance, same-family alternatives, and practical integration considerations. It is intended to help engineers determine whether the original LPC2300 device remains appropriate for an existing 100-LQFP design and how to evaluate a replacement without overlooking changes in memory, peripherals, pin multiplexing, or firmware requirements.

RFQ Contact
LPC2368FET100 - ARM7 72MHz MCU, 512KB Flash, Ethernet, USB | NXP
LPC2368FET100

LPC2368FET100 - ARM7 72MHz MCU, 512KB Flash, Ethernet, USB | NXP

The NXP LPC2368FET100 is a 16/32-bit ARM7TDMI-S microcontroller running at up to 72 MHz, integrating 512 kB of on-chip flash, 58 kB SRAM, 100-pin TFBGA (9x9) package, Ethernet MAC, USB 2.0 Device/Host/OTG, two CAN channels, four UARTs, three SSP/SPI ports, three I2C buses, I2S, an SD/MMC interface, an 8-channel 10-bit ADC, a 10-bit DAC, two PWM blocks, four general-purpose timers, an RTC, and a 10-bit ADC. According to the NXP LPC2368FET100 product page, the device is positioned for embedded applications requiring high peripheral integration and low active-power consumption with the rich connectivity needed for industrial gateways and networked appliances. An ARM7 microcontroller is a member of the 16/32-bit RISC microcontroller family based on the ARM7TDMI-S core, sitting within the broader taxonomy of microcontrollers -> microprocessors -> embedded processors -> semiconductors. Compared with 8-bit 8051 or AVR devices, ARM7 cores offer substantially higher code density (Thumb mode), better interrupt handling, and rich on-chip peripherals for Ethernet and USB connectivity. Compared with later Cortex-M3 cores, ARM7TDMI-S lacks the deterministic interrupt latency and unified memory map of the Cortex-M series, but its mature toolchain (Keil, IAR, GCC) and large code base make it useful for legacy designs and field-deployed products. Key features of the LPC2368FET100 include 72 MHz core clock, 512 kB flash for application code, 58 kB SRAM for data buffering, 100-pin TFBGA package (9x9 mm), Ethernet MAC for 10/100 Mbps networking, USB 2.0 full-speed Device/Host/OTG for USB connectivity, two CAN 2.0B channels for industrial networking, 8-channel 10-bit ADC, and 10-bit DAC for analog signal generation. Integrated peripherals reduce external component count and BOM cost while simplifying PCB layout. The LPC2368FET100 is well suited for industrial gateways, building automation controllers, point-of-sale terminals, networked sensors, and USB peripherals. According to the NXP product page, the high peripheral count (Ethernet, USB, CAN, SD/MMC, multiple UARTs) eliminates the need for many external ICs, reducing both cost and board area. The 72 MHz ARM7 core delivers sufficient throughput for TCP/IP stacks and industrial communication protocols. When designing with this device, ensure decoupling on all power pins and follow NXP AN10414 layout guidelines for TFBGA-100 routing. The integrated PHY is not included - an external Ethernet PHY such as the DP83848 is required for Ethernet applications. The USB DP/DM traces must be 90 ohm differential, length-matched, and routed without stubs.

RFQ Contact