Products (44,000+)

MAX211CDWR - 5V 4/5 RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX211CDWR

MAX211CDWR - 5V 4/5 RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX211CDWR is a 5 V multichannel RS-232 line driver and receiver with four drivers, five receivers, ±9 V output levels, ±15 kV ESD protection, and operation up to 120 kbit/s in a 28-pin SOIC package. It provides the electrical interface between an asynchronous communication controller and a serial-port connector. An RS-232 transceiver is an interface IC that combines logic-level driver and receiver circuits with the voltage levels required by the TIA/EIA-232-F and ITU V.28 serial-interface standards. These devices translate low-voltage digital signals into bipolar RS-232 levels at the transmitter and convert received bipolar signals back into logic levels. The MAX211CDWR also includes a dual charge-pump circuit for generating the required positive and negative voltage rails. Key features include four RS-232 drivers, five RS-232 receivers, a single 5 V supply, ±15 kV ESD protection on serial-port connection pins, and a maximum data rate of 120 kbit/s. The five receivers provide more receive channels than the four transmit channels, allowing additional modem-control or handshake signals to be monitored without requiring separate receiver circuitry. The MAX211CDWR uses a dual charge-pump architecture together with four small external capacitors to produce the bipolar voltage levels required by an RS-232 link. According to the manufacturer product information, the device provides pin-to-pin ESD protection across the serial-port connection pins, including ground, and meets the electrical requirements of TIA/EIA-232-F. These characteristics make the IC appropriate for legacy and industrial asynchronous serial interfaces. Typical applications include industrial equipment controllers, data-acquisition systems, instrument interfaces, point-of-sale equipment, and RS-232 ports on embedded systems. The integrated protection is particularly useful where cables connect to external equipment through long or exposed routes, while the 120 kbit/s rate supports common asynchronous serial protocols and simple command exchanges. Designers should place the charge-pump capacitors close to their associated pins, maintain the recommended external-capacitor values, and provide adequate PCB ground connectivity. Decoupling near VCC is also important because the charge pump and switching elements can return ripple to the supply rail. A clean layout helps preserve signal integrity and makes the protection circuitry more effective. This page consolidates verified manufacturer and distributor information, identifies same-family drop-in candidates, and adds practical placement guidance, comparison parameters, and application-specific selection criteria that are not presented as a single block in the manufacturer datasheet.

RFQ Contact
MAX211CWI+ - 4/5 RS-232 Transceiver | Analog Devices
MAX211CWI+

MAX211CWI+ - 4/5 RS-232 Transceiver | Analog Devices

The Analog Devices MAX211CWI+ is a single-supply RS-232 and V.28 transceiver with four drivers, five receivers, integrated charge-pump circuitry, and a 28-pin wide SOIC package. It operates from 4.5V to 5.5V and supports data rates in excess of 120kbps. The device uses 0.1uF external charge-pump capacitors, while its drivers maintain the ±5V EIA/TIA-232E output levels specified for loaded operation. An RS-232 transceiver is an interface IC that converts between single-ended logic signals and the bipolar voltage levels used by RS-232 links. In the signal hierarchy, MAX211CWI+ belongs to interface ICs and uses driver and receiver sections to connect digital equipment across a serial cable. Its integrated charge pump doubles the supply and inverts it to produce positive and negative transmitter voltages from one +5V input. The principal feature is its four-driver, five-receiver arrangement, which suits equipment with several serial ports, control signals, or status lines. The MAX211 family is specified for data rates above 120kbps and uses four external 0.1uF capacitors for charge-pump operation. The wide SOIC package provides a leaded surface-mount format while keeping the board footprint compatible with the MAX211 family variants identified in the supplied references. The MAX211CWI+ is intended for +5V systems that need RS-232 drivers and receivers rather than RS-422 or RS-485 differential signaling. It can be used in data acquisition, industrial control, test equipment, and embedded serial ports. Because RS-232 is a single-ended, unbalanced interface, cable routing, grounding, and protection against transients remain important system-level considerations. A key design consideration is that the external charge-pump capacitors must be placed close to the device and selected according to the manufacturer guidance. The receiving logic threshold and driver output levels should be checked against the connected equipment, especially when cables are long or the link includes unprotected industrial wiring. The supplied data does not provide a full electrical limit table, so values not explicitly stated there are marked as data needed rather than inferred. This page combines the verified manufacturer and distributor product information with a cautious selection guide, package-aware comparison, and practical integration notes. It distinguishes confirmed MAX211 family details from parameters that require the complete manufacturer datasheet before design release.

RFQ Contact
MAX211EAI+ - 120kbps 4/5 RS-232 Transceiver | Analog Devices
MAX211EAI+

MAX211EAI+ - 120kbps 4/5 RS-232 Transceiver | Analog Devices

The Analog Devices MAX211EAI+ is a +5 V RS-232 and V.28 transceiver with four line drivers, five line receivers, and integrated charge-pump circuitry in a 28-pin SSOP package. It supports data rates up to 120 kbps and uses four 0.1 uF external capacitors. The device provides the electrical interface between an asynchronous communication controller and an RS-232 serial-port connector. An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and a cable-based serial link. The MAX211 family combines drivers, receivers, and voltage-conversion circuitry into a single interface device. It belongs to the interface IC hierarchy and allows a +5 V system to communicate through RS-232 without requiring separate negative supply rails or external line-driver ICs. The MAX211EAI+ supports EIA/TIA-232E and CCITT V.28 operation at data rates up to 120 kbps when loaded according to the cited standards. Its four drivers maintain approximately plus or minus 5 V EIA/TIA-232E output levels, while the five receivers support the logic-side receive function. Four external 0.1 uF charge-pump capacitors allow operation from a single +5 V supply. The integrated dual charge-pump architecture generates the voltage required by the RS-232 line drivers and reduces the number of external supply rails required by the design. The MAX211EAI+ is packaged in the 28-pin SSOP package, identified as EAI in the ordering code. This package provides a compact option for industrial and communication equipment where board area is constrained but a conventional through-hole RS-232 package is unnecessary. Typical uses include industrial serial controllers, instrumentation, POS terminals, data-acquisition equipment, and embedded systems that require a +5 V RS-232 port. The 120 kbps capability is suitable for moderate-speed asynchronous serial communication, while the integrated drivers and receivers reduce the component count compared with separate transmitter and receiver devices. PCB design must reserve the four specified 0.1 uF capacitors and maintain the charge-pump routing recommended by the manufacturer datasheet. Keep high-current charge-pump loops compact, provide an uninterrupted ground plane, and place interface protection close to the connector because external cables can introduce ESD and surge events. This page combines verified manufacturer information, distributor availability, family-level drop-in guidance, package details, and practical PCB design considerations to help engineers evaluate the MAX211EAI+ for compact +5 V RS-232 interface designs.

RFQ Contact
MAX211EEAI+ 4/5 RS-232 Transceiver | Analog Devices
MAX211EEAI+

MAX211EEAI+ 4/5 RS-232 Transceiver | Analog Devices

Analog Devices MAX211EEAI+ is a four-driver, five-receiver RS-232 and V.28 transceiver with an integrated charge pump for operation from a single +5 V supply. It supports data rates in excess of 120 kbps, provides ±15 kV ESD protection on the RS-232 interface, and is packaged in a 28-pin SSOP. The MAX211 family is designed for bidirectional serial communication systems that require TTL/CMOS logic interfacing, compliant ±5 V RS-232 signal levels, and enhanced electrostatic protection. An RS-232 transceiver is an interface IC that converts between single-ended TTL or CMOS logic levels and differential, bipolar RS-232 signals. In the broader semiconductor hierarchy, the MAX211EEAI+ belongs to the interface IC family, combining line drivers, line receivers, and charge-pump voltage generation in one device. This integration allows a host controller or UART to connect to a cable-based RS-232 port without external level-shifting transistors or a separate negative supply rail. The device includes four TTL-compatible transmitters and five receivers. The transmitters produce the ±5 V output levels required by EIA/TIA-232E, while the receivers convert incoming RS-232 signals into logic-compatible levels. Its integrated charge-pump circuitry generates the positive and negative voltages required by the RS-232 drivers from one +5 V supply. The MAX211EEAI+ also supports data rates above 120 kbps when operated in accordance with the EIA/TIA-232E loading requirements. A major feature of the MAX211EEAI+ is its ±15 kV human-body-model ESD protection, which improves interface robustness in environments where cables may be connected or disconnected. The receive and transmit sections provide practical channel counts for systems requiring several serial links, status inputs, control signals, or bidirectional communication through one RS-232 connector. Its 28-pin SSOP package offers a compact surface-mount footprint compared with the larger 28-pin wide SO option also offered in the MAX211 family. Typical uses include industrial equipment interfaces, data-acquisition systems, instrumentation, service consoles, embedded serial adapters, and legacy peripheral connectivity. The device is especially useful when an embedded controller must communicate through a multi-channel RS-232 interface while maintaining a single +5 V power architecture. Because it is a bipolar RS-232 interface rather than a modern differential bus transceiver, it is best suited to point-to-point cable links and compatible equipment rather than long-distance, high-noise industrial Ethernet-style networks. Designers should provide the charge-pump capacitors specified by the manufacturer, connect unused inputs to defined logic levels, and treat the ESD-protected RS-232 pins as external connector pins. Keep the interface ground reference connected with the signal cable, route the interface connector and cable away from sensitive analog signals, and validate the complete board under the grounding conditions of the target system. This page combines the manufacturer specifications, package details, application guidance, comparison information, and verified drop-in candidates for engineers evaluating the MAX211EEAI+. It also highlights practical distinctions among confirmed SSOP-28 alternatives so PCB reuse can be assessed without confusing a package-compatible device with an electrically equivalent but differently pinned part.

RFQ Contact
MAX211EEWI+ - 15kV ESD 4/5 RS-232 Transceiver | Maxim
MAX211EEWI+

MAX211EEWI+ - 15kV ESD 4/5 RS-232 Transceiver | Maxim

The Maxim Integrated MAX211EEWI+ is a 4/5 RS-232 transceiver with four drivers and five receivers, 15kV ESD protection, and single-supply operation from 4.5V to 5.5V. The device is offered in a 28-pin wide small-outline SOIC package and includes an integrated charge pump for single 5V operation. An RS-232 transceiver is an interface IC that converts logic-level signals to and from RS-232 line levels. It belongs to the transceiver class, interface IC hierarchy, and broader semiconductor category. The MAX211EEWI+ combines four driver channels with five receiver channels, allowing multiple serial ports or asymmetric communication paths to share one package while providing a standardized physical interface for data transmission. Key features include 15kV ESD protection, TTL-compatible tri-state driver operation, and operation from a 4.5V to 5.5V supply. The integrated charge pump eliminates the need for a separate external charge-pump supply arrangement for standard single-supply RS-232 operation. Its four-driver and five-receiver organization also provides receiver headroom when a system requires more receive channels than transmit channels. The E suffix identifies the electrically enhanced device family, while the wider temperature capability associated with the EWI+ ordering code is -40°C to +85°C. The MAX211 family is also offered in 28-pin wide SO and SSOP configurations, but the target ordering code uses the 28-pin wide SOIC package. Exact propagation delay, slew rate, receiver thresholds, and input capacitance should be confirmed against the manufacturer datasheet before finalizing a high-speed interface design. Typical uses include industrial serial-port equipment, data acquisition systems, instrumentation, control panels, and embedded systems that connect TTL or CMOS logic to RS-232 equipment. The five-receiver, four-driver arrangement is particularly useful where more input channels are required than output channels. Integrating the charge pump also reduces external circuitry and simplifies single-rail implementation compared with charge-pump-free or externally assisted alternatives. Designers should verify signal-level compatibility, grounding, connector selection, and cable length for the selected RS-232 standard. ESD protection is valuable at the connector interface, but external protection may still be needed for severe industrial surge environments. Keep ground and signal routing controlled, place the charge-pump capacitors close to their specified pins, and avoid using TTL outputs without first confirming the required driver-enable and tri-state behavior. This page combines the Maxim family specifications, verified distributor listings, pin-compatible family alternatives, and application-focused engineering guidance to support component selection and PCB design planning.

RFQ Contact
MAX211EWI+ - 4/5 RS-232 Transceiver, 5V, 120kbps | ADI
MAX211EWI+

MAX211EWI+ - 4/5 RS-232 Transceiver, 5V, 120kbps | ADI

The Analog Devices MAX211EWI+ is a four-driver, five-receiver RS-232 and V.28 transceiver designed for single +5 V supply operation. It supports data rates in excess of 120 kbps, maintains ±5 V EIA/TIA-232E driver output levels, and uses an integrated charge pump to generate the bipolar voltages required by RS-232. The device is supplied in a 28-pin wide SOIC package and requires four external 0.1 µF capacitors for charge-pump operation. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a cable-based RS-232 link. Within the interface hierarchy, the MAX211EWI+ combines a charge-pump voltage converter, RS-232 line drivers, and line receivers into one mixed-signal device. This integration allows a single +5 V system to communicate with legacy RS-232 equipment without a separate negative supply or external RS-232 line-power circuit. Key features include four RS-232 drivers, five receivers, operation above 120 kbps, integrated charge-pump circuitry, and single-supply operation from a nominal +5 V rail. The four external 0.1 µF capacitors required by the EWI+ variant simplify voltage generation but must be placed close to their designated pins to limit charge-pump switching noise. The device provides ±5 V driver levels while operating from a 5 V supply, matching the classic RS-232 electrical requirement for bipolar signaling. The MAX211 architecture divides the transceiver into a charge-pump converter, four driver channels, and five receiver channels. Its integrated charge pump generates the positive and negative rail voltages used by the drivers. Because these rails are switched internally, PCB layout and capacitor placement materially affect radiated and conducted noise. The wide SOIC outline offers adequate lead spacing for through-hole assembly while occupying less area than a 28-pin standard SOIC. Typical applications include industrial serial controllers, test equipment, point-of-sale terminals, instrumentation, and data-acquisition systems. Five receiver channels allow one port to monitor four incoming RS-232 lines while the fourth transmitter drives a separate link, making the device useful for console and diagnostic interfaces. The 120 kbps-plus capability is appropriate for configuration links and moderate-rate data transfers rather than modern high-speed serial protocols. Designers should treat the external charge-pump capacitors and signal routing as critical layout elements. Keep the four 0.1 µF capacitors adjacent to their charge-pump pins, route the charge-pump output as a short and quiet net, and provide adequate bypass capacitance on the +5 V supply. Because the MAX211EWI+ is a legacy RS-232 interface rather than an EIA/TIA-422 or RS-485 transceiver, cable length, grounding, and protection-network design remain application-specific responsibilities. This page combines manufacturer specifications, distributor references, drop-in family alternatives, and application-focused design guidance. It highlights the practical differences between temperature and packaging order codes and identifies the verification gaps that must be closed before a PCB redesign or cross-brand substitution is approved.

RFQ Contact
MAX211IDB - 5V RS-232 Transceiver, 120kbps, ±15kV ESD | TI
MAX211IDB

MAX211IDB - 5V RS-232 Transceiver, 120kbps, ±15kV ESD | TI

The Texas Instruments MAX211IDB is a 5-V multichannel RS-232 line driver/receiver with ±15 kV ESD protection, packaged in a 28-pin SSOP (DB). The device integrates four line drivers, five line receivers, and a dual charge-pump circuit, supports data rates up to 120 kbps, and provides ±9 V output swing for compliant TIA/EIA-232-F signaling. What is an RS-232 line driver/receiver? An RS-232 transceiver is an interface IC that translates between the low-voltage logic levels used by a UART or microcontroller (typically 0 V to 5 V or 3.3 V) and the higher-voltage bipolar signaling levels required by the legacy TIA/EIA-232-F standard (±5 V to ±15 V). It belongs to the broader family of line transceivers (interface ICs > drivers, receivers, transceivers) and acts as the electrical translator between an asynchronous communication controller and a DB-9 or DB-25 serial-port connector. The on-chip charge pump generates the bipolar rails from a single 5 V supply, eliminating the need for external ±12 V power. Key features of the MAX211IDB include integrated dual charge pump with four external 0.1 µF capacitors, ±15 kV ESD protection on serial-port connection pins (Human-Body Model per TIA/EIA-232-F requirements), four drivers and five receivers, true TTL/CMOS input compatibility on receiver inputs, and a low 1.5 mA typical supply current. The device operates from a single 5 V supply and requires no external ±12 V rails, simplifying industrial and embedded designs. Internally the MAX211IDB uses a switched-capacitor voltage converter (charge pump) to derive +10 V and -10 V from the 5 V input. These rails feed the drivers, allowing them to swing beyond the supply rails per RS-232 specifications. The drivers are inverting (true RS-232 inverters), while the receivers invert again so overall the data path is non-inverting between the UART TX/RX lines and the cable-side DTR/DSR/RTS/CTS/RI/DCD lines. Typical applications include industrial PCs and point-of-sale terminals, serial-port debug consoles on embedded systems, legacy modem interfaces, factory automation controllers, and any system requiring TIA/EIA-232-F signaling from a single 5 V rail. When designing with this part, place the four charge-pump capacitors as close to the IC pins as possible and provide adequate ground plane beneath the SSOP-28 body to keep EMI and supply ripple low.

RFQ Contact
MAX211IDBR - 5V RS-232 Transceiver, 120kbps, ±15kV ESD | TI (Tape & Reel)
MAX211IDBR

MAX211IDBR - 5V RS-232 Transceiver, 120kbps, ±15kV ESD | TI (Tape & Reel)

The Texas Instruments MAX211IDBR is a 5-V multichannel RS-232 line driver/receiver with ±15 kV ESD protection, packaged in a 28-pin SSOP (DB). The device integrates four line drivers, five line receivers, and a dual charge-pump circuit, supports data rates up to 120 kbps, and provides ±9 V output swing for compliant TIA/EIA-232-F signaling. What is an RS-232 line driver/receiver? An RS-232 transceiver is an interface IC that translates between the low-voltage logic levels used by a UART or microcontroller (typically 0 V to 5 V or 3.3 V) and the higher-voltage bipolar signaling levels required by the legacy TIA/EIA-232-F standard (±5 V to ±15 V). It belongs to the broader family of line transceivers (interface ICs > drivers, receivers, transceivers) and acts as the electrical translator between an asynchronous communication controller and a DB-9 or DB-25 serial-port connector. The on-chip charge pump generates the bipolar rails from a single 5 V supply, eliminating the need for external ±12 V power. Key features of the MAX211IDBR include integrated dual charge pump with four external 0.1 µF capacitors, ±15 kV ESD protection on serial-port connection pins (Human-Body Model per TIA/EIA-232-F requirements), four drivers and five receivers, true TTL/CMOS input compatibility on receiver inputs, and a low 1.5 mA typical supply current. The device operates from a single 5 V supply and requires no external ±12 V rails, simplifying industrial and embedded designs. Internally the MAX211IDBR uses a switched-capacitor voltage converter (charge pump) to derive +10 V and -10 V from the 5 V input. These rails feed the drivers, allowing them to swing beyond the supply rails per RS-232 specifications. The drivers are inverting (true RS-232 inverters), while the receivers invert again so overall the data path is non-inverting between the UART TX/RX lines and the cable-side DTR/DSR/RTS/CTS/RI/DCD lines. Typical applications include industrial PCs and point-of-sale terminals, serial-port debug consoles on embedded systems, legacy modem interfaces, factory automation controllers, and any system requiring TIA/EIA-232-F signaling from a single 5 V rail. When designing with this part, place the four charge-pump capacitors as close to the IC pins as possible and provide adequate ground plane beneath the SSOP-28 body to keep EMI and supply ripple low.

RFQ Contact
MAX211IDBRE4 - 5V RS-232 Transceiver | Texas Instruments
MAX211IDBRE4

MAX211IDBRE4 - 5V RS-232 Transceiver | Texas Instruments

Texas Instruments MAX211IDBRE4 is a 5 V multichannel RS-232 line driver/receiver with four drivers, five receivers, operation to 120 kbit/s, and ±15 kV human-body-model ESD protection in a 28-pin SSOP package. The device operates from a 4.5 V to 5.5 V supply over a -40°C to +85°C temperature range and includes a low-power shutdown mode. An RS-232 transceiver is an interface IC that converts low-voltage digital signals into RS-232 levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the hierarchy of RS-232 interface transceivers, multi-channel line drivers and receivers, interface ICs, and semiconductors. Such devices simplify bidirectional serial connectivity between equipment such as industrial controllers, test equipment, and legacy computer peripherals. The MAX211IDBRE4 combines four line drivers with five receivers, allowing four outputs and five inputs to share one interface package. Its maximum data rate of 120 kbit/s suits legacy serial ports and control links. Input receiver hysteresis of 500 mV improves noise immunity, while ±15 kV HBM protection improves tolerance of electrostatic discharge on serial-port connections. The specified 5 V operation is compatible with conventional 5 V digital systems. Internally, the receiver side uses Schmitt-trigger inputs, which provide hysteresis between the low and high switching thresholds. This helps prevent repeated switching as a noisy input crosses the transition region. The integrated driver and receiver functions support asymmetric channel counts, while the shutdown circuit reduces supply current to 1 µA typical when the interface is not active. These characteristics make the device useful where several RS-232 ports must share a common logic-side supply. Typical applications include multiport industrial controllers, programmable logic controller communications, test and measurement equipment, instrument-control interfaces, and legacy peripheral connections. The 28-pin SSOP surface-mount package also allows reuse of an existing MAX211-family circuit footprint without changing to a through-hole package. Design the circuit with short, appropriately terminated RS-232 routes, maintain the specified 4.5 V to 5.5 V supply range, and account for ground potential differences between connected equipment. Use the manufacturer pin-description table and application guidance when assigning connector-side and logic-side signals. Verify shutdown-state behavior and ESD requirements at the complete system level. This page combines the MAX211IDBRE4 electrical specifications, package details, RS-232 design guidance, comparison parameters, and qualified drop-in alternatives to support faster component selection and PCB-level replacement decisions.

RFQ Contact
MAX211IDBRG4 - 5V 120kbps RS-232 Transceiver | TI
MAX211IDBRG4

MAX211IDBRG4 - 5V 120kbps RS-232 Transceiver | TI

Texas Instruments MAX211IDBRG4 is a 5V multichannel RS-232 line driver and receiver with four drivers, five receivers, 120 kbit/s operation, and ±15 kV ESD protection, packaged in a 28-pin SSOP. It provides the electrical interface between an asynchronous communication controller and an RS-232 serial connector. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 differential voltage levels and converts received RS-232 signals back into logic-compatible levels. This signal-conditioning layer sits between a serial communication controller and an external connector. The MAX211 belongs to the broader RS-232 interface, transceiver, interface IC, and semiconductor hierarchy. Its integrated dual charge pump generates the positive and negative voltage levels required by RS-232 while allowing operation from a single 5V supply. The device includes four RS-232 drivers, five RS-232 receivers, and pin-to-pin ESD protection rated at ±15 kV using the human-body model. It operates at up to 120 kbit/s and meets the requirements of TIA/EIA-232-F and ITU V.28, as identified in the manufacturer datasheet. An enable control supports low-power shutdown, while the low shutdown supply current helps suit equipment where the serial interface is not continuously active. The dual charge-pump architecture is a key technical feature. Four small external capacitors support the charge-pump circuit, allowing the interface to produce the bipolar voltage swings needed for RS-232 communication. The four-driver and five-receiver arrangement supports applications requiring more receive channels than transmit channels, while the shared 5V supply simplifies interface implementation in industrial-control, test, and embedded systems. Typical uses include multi-channel RS-232 port expansion, industrial data acquisition, service and configuration interfaces, legacy peripheral connectivity, and embedded control systems that retain a serial console. The industrial temperature range of −40°C to +85°C supports use across commercial and industrial environments where temperature variation is expected. PCB design should preserve short charge-pump capacitor connections and provide adequate input and output return paths for every RS-232 channel. Place ESD-protection and signal-routing structures near the connector when the external cable creates a direct electrostatic-discharge path. Confirm signal polarity, receiver direction, enable state, and connector mapping before releasing a new layout. This page combines the manufacturer’s electrical specifications, verified drop-in replacement information, application guidance, package details, and practical layout considerations to accelerate component selection and PCB implementation.

RFQ Contact
MAX211IDW - 5V 120kbps RS-232 Transceiver | Texas Instruments
MAX211IDW

MAX211IDW - 5V 120kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX211IDW is a 5 V multichannel RS-232 line driver and receiver with four drivers, five receivers, and ±15 kV ESD protection, packaged in a 28-pin SOIC. It supports data rates up to 120 kbit/s and operates across the industrial -40°C to +85°C temperature range. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into digital logic. Within the interface hierarchy, MAX211IDW is a multichannel RS-232 transceiver built around four RS-232 line drivers, five line receivers, and a dual charge-pump circuit. This topology allows multiple serial channels to share one supply while providing bipolar voltage generation for the driver outputs. Key features include a 5 V supply, operation to 120 kbit/s, four line drivers, five line receivers, and ±15 kV ESD protection across the serial-port connection pins, including ground. The device is designed to meet the requirements of TIA/EIA-232-F and ITU V.28. Its additional fifth receiver provides flexibility for monitoring a modem handshake signal when the four main driver and receiver channels are already assigned. The MAX211 architecture uses a dual charge-pump circuit to generate the positive and negative voltages required by RS-232 drivers. Four small external capacitors support charge-pump operation. The resulting interface can place a communication controller on the logic side and a DB9 or other RS-232 connector on the line side without requiring discrete level-shifting circuits. Pin-to-pin ESD protection extends robustness across exposed serial-port connections. Typical uses include industrial serial-port adapters, data-acquisition equipment, POS terminals, service interfaces, and legacy computer peripherals. The 120 kbit/s operating rate supports moderate-speed asynchronous communication, while the four-driver and five-receiver arrangement is useful for systems requiring several handshake or control lines. The -40°C to +85°C range also suits industrial environments where commercial-temperature interface ICs may be insufficient. Designers should use the manufacturer's charge-pump capacitor and bypass-capacitor recommendations, place the external capacitors close to their pins, and keep sensitive logic and communications routing separated from exposed connector and ESD paths. The device is marked last-time-buy by a verified distributor listing, so new designs should confirm availability and consider a supported modern interface before committing to a large production run. This page combines verified manufacturer and distributor information with lifecycle context, drop-in alternatives, comparison parameters, and practical interface-design guidance. It highlights where MAX211IDW remains suitable for multichannel RS-232 and where supply availability or newer USB-to-serial solutions may be more appropriate.

RFQ Contact
MAX211IDWR - 5V 120kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX211IDWR

MAX211IDWR - 5V 120kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments MAX211IDWR is a 5 V multichannel RS-232 line driver and receiver with four drivers, five receivers, and ±15 kV ESD protection, packaged in a 28-pin SOIC. It supports data rates up to 120 kbit/s and operates across the industrial -40°C to +85°C temperature range. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into digital logic. Within the interface hierarchy, MAX211IDWR is a multichannel RS-232 transceiver built around four RS-232 line drivers, five line receivers, and a dual charge-pump circuit. This topology allows multiple serial channels to share one supply while providing bipolar voltage generation for the driver outputs. Key features include a 5 V supply, operation to 120 kbit/s, four line drivers, five line receivers, and ±15 kV ESD protection across the serial-port connection pins, including ground. The device is designed to meet the requirements of TIA/EIA-232-F and ITU V.28. Its additional fifth receiver provides flexibility for monitoring a modem handshake signal when the four main driver and receiver channels are already assigned. The MAX211 architecture uses a dual charge-pump circuit to generate the positive and negative voltages required by RS-232 drivers. Four small external capacitors support charge-pump operation. The resulting interface can place a communication controller on the logic side and a DB9 or other RS-232 connector on the line side without requiring discrete level-shifting circuits. Pin-to-pin ESD protection extends robustness across exposed serial-port connections. Typical uses include industrial serial-port adapters, data-acquisition equipment, POS terminals, service interfaces, and legacy computer peripherals. The 120 kbit/s operating rate supports moderate-speed asynchronous communication, while the four-driver and five-receiver arrangement is useful for systems requiring several handshake or control lines. The -40°C to +85°C range also suits industrial environments where commercial-temperature interface ICs may be insufficient. Designers should use the manufacturer's charge-pump capacitor and bypass-capacitor recommendations, place the external capacitors close to their pins, and keep sensitive logic and communications routing separated from exposed connector and ESD paths. The device is marked last-time-buy by a verified distributor listing, so new designs should confirm availability and consider a supported modern interface before committing to a large production run. This page combines verified manufacturer and distributor information with lifecycle context, drop-in alternatives, comparison parameters, and practical interface-design guidance. It highlights where MAX211IDWR remains suitable for multichannel RS-232 and where supply availability or newer USB-to-serial solutions may be more appropriate.

RFQ Contact
MAX213ECAI+ - 5V RS-232 Transceiver, 15kV ESD, SSOP-28 | Maxim
MAX213ECAI+

MAX213ECAI+ - 5V RS-232 Transceiver, 15kV ESD, SSOP-28 | Maxim

The Maxim Integrated MAX213ECAI+ is a +5V-powered RS-232 transceiver with integrated charge-pump circuitry and ±15kV ESD protection, housed in a 28-pin SSOP package. It provides four drivers and five receivers in a TTL tri-state-compatible interface, operates from a single 4.5V to 5.5V supply, and supports data rates up to 120 kbps for asynchronous serial communication. A RS-232 transceiver is an interface IC that converts between TTL/CMOS logic levels (0V/5V) and the bipolar ±5V to ±15V signalling required by the RS-232 standard. It belongs to the broader family of line transceivers (RS-232, RS-422, RS-485), which themselves sit inside the interface ICs category and the larger umbrella of wired communication semiconductor components. By embedding the charge pump on-chip, the MAX213 eliminates the need for external ±12V supplies, simplifying PCB design in point-of-sale terminals, industrial controllers and embedded computing platforms. Key features include ±15kV ESD protection on every transmitter output and receiver input (per HBM), four RS-232 drivers and five RS-232 receivers in the SSOP-28 footprint, tri-state TTL/CMOS compatible receiver outputs, and an integrated charge pump that requires only four external 0.1 µF capacitors. The device operates across the commercial 0°C to 70°C temperature range, and its low supply current (~20 mA typical, unloaded) suits battery-backed systems that must wake serial ports only during transactions. Technically, the MAX213ECAI+ uses Maxim's BiCMOS process that combines bipolar drive transistors (for true ±5V RS-232 swing) with CMOS control logic. The charge pump runs as a voltage doubler and inverter from VCC=5V, generating V+ ≈ +10V and V- ≈ -10V which feed the driver output stages. Receivers implement a 0.8V/2.4V-thresholded Schmitt-trigger input structure with 5 kΩ pull-down resistors to ground, ensuring a defined logic-high output when the input is open-circuited. Internal slew-rate control limits data rates to ~120 kbps, which is well matched to legacy serial peripherals, debug consoles and embedded modem links. Typical applications include industrial PCs and point-of-sale equipment needing multi-port serial expansion, embedded microcontroller debug consoles, GPS receivers and GSM/cellular modules with RS-232 interfaces, and legacy peripheral interfaces such as optical mice, bar-code scanners and serial printers where robust ±15kV ESD handling protects against hot-plug discharge. When designing with this IC, keep charge-pump capacitor traces short (less than ~10 mm) and place the four 0.1 µF ceramics as close to C1+, C1-, C2+, C2- pins as possible. Reserve TVS diodes externally on the connector side for ESD events that exceed the on-chip rating, especially for cables longer than 3 metres. This page consolidates distributor pricing, drop-in alternative MPNs and practical PCB layout notes that go beyond the manufacturer's datasheet, giving engineers a one-stop reference for selecting, sourcing and laying out the MAX213ECAI+.

RFQ Contact
MAX22025AWA+ - 3.5kVRMS Isolated RS-485 Transceiver | ADI
MAX22025AWA+

MAX22025AWA+ - 3.5kVRMS Isolated RS-485 Transceiver | ADI

The Analog Devices (formerly Maxim Integrated) MAX22025AWA+ is a compact, isolated half-duplex RS-485/RS-422 transceiver that integrates 3.5kVRMS of digital galvanic isolation in an 8-pin wide-body SOIC package. It supports data rates up to 500 kbps and operates from a single 3.3V supply on the UART side, eliminating the need for an external isolated DC-DC converter in many designs. The wide-body SOIC provides 5.5mm of creepage, meeting IEC 60664 reinforced insulation requirements for industrial and renewable-energy installations. An RS-485/RS-422 transceiver is a differential line driver/receiver IC that translates a single-ended UART signal into a balanced differential pair. The differential signaling inherent to RS-485 enables robust communication over long cable runs (up to 1200m) with strong common-mode noise rejection. Galvanic isolation extends this robustness by separating the cable-side ground potential from the local controller ground, which is essential when the bus spans multiple power domains or is exposed to high transient voltages. Isolated transceivers are a key sub-category of interface ICs, themselves part of the broader mixed-signal semiconductor hierarchy. Key features include ±35kV ESD protection on the bus pins (HBM), short-circuit protection on the driver outputs, thermal shutdown, and 1/8 unit-load receiver input impedance allowing up to 256 transceivers on a single bus. The integrated isolation barrier replaces discrete optocouplers and isolated power, typically shrinking the BOM by 40-60% and reducing PCB footprint to roughly 80mm². The device supports -40°C to +85°C operation and is specified over a wide 3.0V to 5.5V UART-side VDD range. Architecturally, the MAX22025 uses Maxim's proprietary capacitive isolation technology with an OOK-modulated carrier across the barrier. The cable-side driver meets the RS-485 standard's 1.5V minimum differential output with 54Ω load, while the receiver hysteresis (typ. 30mV) ensures clean switching even on heavily attenuated signals. On-chip deglitch filters suppress transient bus spikes up to 150ns. Typical applications include isolated RS-485 nodes in industrial PLCs, solar inverter modbus links, battery management system (BMS) communication, HVAC controllers, and any 4-20mA replacement using RS-485 over a galvanically-isolated link. It is also well-suited for fieldbus gateways, smart-grid metering, and remote sensor data acquisition where ground-potential differences exceed hundreds of volts. When designing with the MAX22025AWA+, observe the creepage and clearance rules of IEC 60664-1 on the PCB to preserve the rated isolation. A bypass capacitor of 0.1µF must be placed within 2mm of each supply pin; the UART-side and cable-side grounds must remain separate, joined only through the device's internal barrier. Verify the driver slew rate at your chosen data rate to control EMI.

RFQ Contact
MAX222CN - 5V Dual RS-232 Transceiver | Texas Instruments
MAX222CN

MAX222CN - 5V Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX222CN is a 5 V dual RS-232 line driver and receiver, also described as a two-driver, two-receiver full-duplex transceiver, with operation to 200 kbit/s and ±15 kV human-body-model ESD protection in an 18-pin PDIP package. The device is intended for legacy and industrial RS-232 links where a 5 V supply, through-hole construction, and dual-channel signal conditioning are required. An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions into a system-facing serial port. Its hierarchy is transceiver > RS-232 interface > line driver/receiver > semiconductor. The MAX222CN translates logic-level signals between a host UART and RS-232 line drivers, while its receivers convert incoming RS-232 levels into CMOS-compatible digital signals. The integrated dual-channel arrangement reduces the component count for two-wire, full-duplex RS-232 communication. Key verified features include a 5 V VCC supply, operation to 200 kbit/s, ±15 kV human-body-model ESD protection, low shutdown supply current, and external-capacitor charge-pump operation using 0.1 µF. The listed standards claim compliance with or exceedance of TIA/EIA-232-F and ITU V.28 requirements. Its 18-pin PDIP package supports through-hole PCB assembly rather than compact surface-mount layouts. The MAX222CN is a legacy RS-232 interface, not an RS-485 transceiver and not a modern USB-to-serial converter. Its receiver hysteresis and supply range are listed in distributor data, while the complete electrical limits should be checked in the manufacturer datasheet before using the part outside the stated conditions. The dual drivers and receivers support point-to-point RS-232 links, instrumentation connections, and embedded systems that already expose a UART. Typical uses include industrial control consoles, test equipment, serial adapters, and legacy peripheral interconnects. The principal design consideration is that RS-232 is a single-ended, unbalanced interface intended for shorter distances than differential buses. Designers should use suitable protection, grounding, and cable practices, and should not treat ±15 kV ESD protection as a substitute for external surge or lightning protection. This page consolidates the verified distributor descriptions, package information, RS-232 capability, and cross-reference research for MAX222CN. It does not invent electrical limits, pricing, or pin assignments that were not supplied in the verified data.

RFQ Contact
MAX222IN - 5V Dual RS-232 Interface | Texas Instruments
MAX222IN

MAX222IN - 5V Dual RS-232 Interface | Texas Instruments

The Texas Instruments MAX222IN is a 5 V dual RS-232 line driver and receiver with ±15 kV ESD protection, operating at up to 200 kbit/s in an 18-pin PDIP package. It provides two transmit channels and two receive channels, making it suitable for bidirectional serial interfaces, instrumentation, industrial control, and data acquisition equipment. The device is designed to meet TIA/EIA-232-F and ITU V.28 interface requirements while operating from a single 5 V supply. An RS-232 transceiver is an interface IC that converts logic-level digital signals between a host or controller and a RS-232 communication link. Unlike a differential bus such as RS-485, RS-232 uses single-ended signaling with positive and negative voltage levels. The MAX222IN combines drivers, receivers, and internal level-shift capability in one package, reducing the number of external interface components required in a conventional RS-232 port. The MAX222IN operates from a 5 V VCC supply and supports data rates up to 200 kbit/s. Its two drivers and two receivers support full-duplex point-to-point communication when connected to the corresponding RS-232 lines. The verified product description also identifies ±15 kV human-body-model ESD protection, low shutdown supply current, and operation over a -40 °C to +85 °C temperature range. These characteristics make the device appropriate for both commercial and industrial equipment. The MAX222IN is packaged in an 18-pin PDIP, identified by the N package designation in the part number. The through-hole package is appropriate for systems assembled with conventional plated-through-hole components and for prototypes or industrial controllers where through-hole interchangeability is useful. The verified distributor listing identifies the device as a 2/2 full RS-232 transceiver in an 18-PDIP package. Typical uses include RS-232 ports in test equipment, serial adapters, embedded controllers, industrial instrumentation, and communications equipment. Designers should provide the required charge-pump capacitors, connect the supply and ground correctly, and route the RS-232 connector-side signals away from sensitive low-level circuitry. External protection, grounding, and isolation may be required when the cable is exposed to long, unshielded, or electrically noisy environments. The product information supplied here combines distributor listings, datasheet search results, and the MAX222 family datasheet link. It distinguishes verified specifications from unavailable parameters and does not infer electrical limits that are not present in the supplied data.

RFQ Contact
MAX22513ATI+ - Dual IO-Link Transceiver, 36V, TQFN-28 | ADI
MAX22513ATI+

MAX22513ATI+ - Dual IO-Link Transceiver, 36V, TQFN-28 | ADI

The Analog Devices MAX22513ATI+ is a dual-channel, low-power IO-Link device transceiver integrating a selectable control interface, a high-efficiency internal DC-DC buck regulator, two internal linear regulators, and integrated surge protection on every IO pin. Housed in a 28-pin TQFN-EP (5.5mm body) surface-mount package, the part operates from 8V to 36V and delivers C/Q plus DO/DI drivers with selectable current limits and overcurrent protection to minimize dissipation in fault conditions. The integrated surge protection of ±1kV/500Ω on all four IO pins (V24, C/Q, DO/DI, GND) is unique among IO-Link transceivers and eliminates external TVS arrays in most designs. An IO-Link device transceiver is a mixed-signal interface that sits between an industrial sensor/actuator and an IO-Link master, handling the IEC 61131-9 physical layer: the C/Q line carries the wake-up pulse, the COM1/COM2/COM3 framed communication, and the high-current switching output; DO/DI provides an auxiliary digital channel. IO-Link transceivers belong to the broader category of industrial sensor interfaces -> more generally to line drivers/receivers -> and finally to wired communication ICs, which are themselves a subset of mixed-signal semiconductors used in factory-automation networks. Key differentiating features include: an integrated high-efficiency step-down DC-DC converter that generates the 5V or 3.3V logic rail directly from the 24V industrial bus, eliminating an external switching IC; reverse-voltage, short-circuit, and surge protection on all four IO pins; very low on-resistance C/Q and DO/DI drivers; selectable driver current limits to match load requirements; and low quiescent current for IEC 61131-9 sleep/wake behavior. The selectable interface (SPI or pin-strapped logic) lets the same silicon serve multiple microcontroller families. The 28-TQFN-EP package has an exposed pad that drops θJA low enough to dissipate the buck regulator's thermal load without an external heatsink at typical 24V→5V/200mA operating points. Typical applications include 24V industrial sensor heads (photoelectric, proximity, ultrasonic), IO-Link valve manifolds, IO-Link actuators, and remote I/O blocks on Profinet/EtherNet/IP fieldbus modules. The combination of surge protection and integrated DC-DC keeps the BOM small for IP67 sensor heads where PCB area is constrained and external protection networks are difficult to source. Designers should budget for the buck regulator's inductor and output capacitors per the datasheet typical application circuit, and verify that the surge protection rating meets the end-application EMC standard (IEC 61000-4-5). The exposed pad requires multiple thermal vias to the inner copper layers for adequate heat extraction at full-load buck operation. This page synthesizes distributor pricing, drop-in alternatives, IO-Link protocol design considerations, and PCB layout notes not collected in the manufacturer datasheet alone.

RFQ Contact
MAX22530AWE+ - Isolated 12-bit 4-Ch SAR ADC | Analog Devices
MAX22530AWE+

MAX22530AWE+ - Isolated 12-bit 4-Ch SAR ADC | Analog Devices

The Analog Devices MAX22530AWE+ is a galvanically isolated, 4-channel, multiplexed, 12-bit successive-approximation-register (SAR) analog-to-digital converter (ADC) housed in a 16-pin wide-body SOIC (WSOIC) package. According to the MAX22530 datasheet, it integrates an isolated DC-DC converter that powers all field-side circuitry, allowing field-side measurements to be taken with no external power supply. The device samples at up to 22 ksps and exposes a serial (SPI-compatible) digital interface on the logic side. A SAR ADC is a successive-approximation-register analog-to-digital converter, a class of precision ADC that uses a binary-search algorithm and a precision DAC to convert an input voltage to a digital code in a fixed number of clock cycles. Isolated ADCs sit within the broader signal-chain hierarchy of data-acquisition front ends -> ADCs -> precision converters -> mixed-signal ICs -> semiconductors, where galvanic isolation adds a critical safety barrier between hazardous field voltages and the host processor. Key features include 12-bit resolution, four single-ended input channels multiplexed to one SAR core, integrated digital isolation, an integrated isolated DC-DC converter on chip, and a logic-side supply range of 1.71 V to 5.5 V. The wide-body SOIC package provides the reinforced clearance/creepage required for reinforced isolation. The MAXSafe™ architecture is designed for industrial sensors, PLC analog input modules, and any system that requires isolation between the analog front end and a low-voltage digital controller. Typical applications include isolated voltage and current sensing in motor drives, solar inverters, and industrial process-control loops; PLC analog input modules; battery-management systems; and medical equipment where patient isolation is mandatory. The internal DC-DC converter eliminates the bulky external isolated supply, shrinking the BOM. When designing with the MAX22530, pay attention to the input-channel MUX settling time and the recommended input RC anti-alias filter. Place decoupling capacitors close to both field-side and logic-side supply pins, and observe the wide-body SOIC PCB clearance rules for the rated isolation voltage.

RFQ Contact
MAX232ACPE+ - RS-232 Transceiver, 5V, PDIP-16 | Maxim
MAX232ACPE+

MAX232ACPE+ - RS-232 Transceiver, 5V, PDIP-16 | Maxim

The Maxim Integrated MAX232ACPE+ is a +5 V RS-232 line-driver and receiver interface IC with two transmit channels and two receive channels in a 16-pin PDIP package. It supports the MAX220–MAX249 family use case for EIA/TIA-232E and V.28/V.24 communications interfaces where ±12 V supplies are unavailable. The verified distributor listings identify the part as a 5 V-powered multichannel RS-232 driver/receiver, while the target MPN is the +5 V-listed MAX232ACPE+ variant. An RS-232 transceiver is an interface IC that translates digital logic levels between a host or controller and a RS-232 cable. A driver converts TTL or CMOS signals into RS-232-level signals, while a receiver converts transmitted RS-232 levels back into logic levels. The MAX232ACPE+ is therefore placed between a digital system and an external serial connector, providing bidirectional communication through two driver and two receiver channels. The manufacturer family description states that the MAX220–MAX249 devices are intended for EIA/TIA-232E and V.28/V.24 communications interfaces, particularly where ±12 V is not available. The +5 V-powered architecture supports systems whose logic supply is commonly 5 V. The verified data also identifies the part as a 2/2 transceiver and as a 5 V multichannel RS-232 driver/receiver. Exact electrical limits, slew rates, receiver thresholds, supply-current figures, and temperature limits are marked as DATA_NEEDED because they are not included in the supplied verified excerpts. Typical uses include RS-232 console links, industrial-control serial ports, test equipment, embedded serial adapters, and legacy peripheral connections. The MAX232ACPE+ is appropriate when the board requires a conventional through-hole RS-232 interface and a 16-pin PDIP footprint. Designers should verify the complete datasheet pinout, charge-pump capacitor requirements, logic levels, data-rate limits, and ESD requirements before production release, because those values are not present in the supplied source snippets. The key design consideration is to treat the MAX232ACPE+ as a physical-layer interface rather than a protocol converter. The application must handle framing, baud-rate configuration, parity, flow control, and connector wiring separately. External charge-pump capacitors, input/output protection, grounding, and cable routing remain important in a working RS-232 design. The MAX232ACPE+ is best selected when a 16-pin PDIP RS-232 transceiver with two drivers and two receivers is required and the existing board already matches the verified package and pin arrangement. This page combines the verified distributor identity, manufacturer-family interface description, package information, and sourced cross-reference data. It does not infer unprovided electrical specifications, lifecycle claims, pricing values, compliance status, or complete pin assignments.

RFQ Contact
MAX232ACSE+ - +5V RS-232 Transceiver | Analog Devices
MAX232ACSE+

MAX232ACSE+ - +5V RS-232 Transceiver | Analog Devices

The Analog Devices MAX232ACSE+ is a +5 V-powered, 2-transmitter and 2-receiver RS-232 interface transceiver packaged in a 16-pin SOIC. It belongs to the MAX220–MAX249 family of line drivers and receivers designed for EIA/TIA-232E and V.28/V.24 communication interfaces when ±12 V supplies are unavailable. The device provides the voltage conversion needed to connect low-voltage digital logic to a balanced RS-232 transceiver. An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions with logic-level conversion. The MAX232ACSE+ integrates two transmitters and two receivers, placing two RS-232 channels in one 16-pin surface-mount package. This integration is useful in equipment that requires bidirectional serial communication without external driver and receiver ICs. The MAX232ACSE+ operates from a +5 V supply and is identified in the manufacturer literature as a multichannel RS-232 driver and receiver. Its two-driver, two-receiver arrangement supports point-to-point links, control interfaces, industrial equipment, and communications ports that conform to the stated EIA/TIA-232E and V.28/V.24 interface families. The 16-SOIC package supports compact surface-mount PCB construction. The MAX220–MAX249 family uses on-chip charge-pump circuitry to generate the voltage levels required by RS-232 signals from a single positive supply. This topology lets the interface operate without a separate negative supply rail while preserving the positive and negative signal swings expected by RS-232 receivers. Exact charge-pump capacitor requirements and timing values should be taken from the manufacturer datasheet. Typical applications include computer and embedded-system service ports, industrial control links, test equipment, data-acquisition systems, and RS-232 connections between modern CMOS logic and legacy peripherals. The two transmitters and two receivers also support designs that need both command and status paths across one interface IC. PCB implementation should follow the manufacturer datasheet’s charge-pump capacitor and layout guidance. Keep the charge-pump connections compact, provide a stable ground return, and route RS-232 traces away from sensitive analog and high-speed digital nodes. Confirm the selected connector’s signal assignment and any required protection network before field deployment. This page combines the manufacturer family information with package, sourcing, and replacement guidance. It also distinguishes the closest same-footprint options and explains when an electrical or thermal difference prevents a replacement from being treated as a true drop-in substitute.

RFQ Contact
MAX232ACSE+T - 5V RS-232 Transceiver, 2 Driver/2 Receiver | Maxim Integrated
MAX232ACSE+T

MAX232ACSE+T - 5V RS-232 Transceiver, 2 Driver/2 Receiver | Maxim Integrated

The Analog Devices (Maxim Integrated) MAX232ACSE+T is a +5V-powered, multichannel RS-232 driver/receiver IC delivering 2 drivers and 2 receivers in a 16-pin narrow-body SOIC (NSOIC-16) package. It operates from a single 4.5V to 5.5V supply, integrates a charge-pump DC-DC converter that generates the ±10V RS-232 signal swings from the +5V rail, and supports data rates up to 200 kbps. The +T suffix denotes tape-and-reel packaging. What is an RS-232 transceiver? An RS-232 transceiver is a type of line driver/receiver IC that translates logic-level UART signals (0V/5V or 0V/3.3V) to the bipolar ±5V to ±15V voltage levels defined by the EIA/TIA-232E and V.28/V.24 standards, enabling reliable data transmission between a microcontroller/FPGA and legacy serial ports, modems, point-of-sale terminals, and industrial instrumentation over cables up to 15 meters. The MAX232 family belongs to the broader category hierarchy: RS-232 transceiver -> line driver/receiver -> interface IC -> integrated circuit -> semiconductor. Key features include a wide +4.5V to +5.5V single-supply range, on-board dual charge pump (no external ±12V required), 200 kbps guaranteed data rate, ±30V receiver input tolerance (HBM ESD on older MAX232 revisions), 1 µA low-power shutdown mode, and integrated ESD protection on the RS-232 pins (device-dependent). The NSOIC-16 surface-mount package provides a compact footprint suitable for industrial, embedded, and consumer designs. The architecture uses an internal oscillator and four external 0.1uF charge-pump capacitors (C1+, C1-, C2+, C2-, V+, V-) to generate the required RS-232 voltage rails from a single +5V source. Drivers invert and level-shift TTL/CMOS inputs, while receivers accept bipolar RS-232 inputs and re-emit TTL/CMOS logic levels. The MAX232A variant specifies a higher slew rate than the original MAX232, supporting the 200 kbps data rate. Typical applications include industrial PLC serial ports, point-of-sale (POS) terminals, embedded microcontroller UART bridges, legacy PC peripheral interconnects, GPS module interfaces, and battery-backed service equipment. The single +5V supply eliminates the bulky ±12V rails required by older RS-232 designs, simplifying power architecture. When designing with the MAX232ACSE+T, place the four charge-pump capacitors (typically 0.1uF ceramic) as close as possible to the C1+, C1-, C2+, C2-, V+, and V- pins to minimize ripple on the generated RS-232 rails. For applications requiring higher ESD protection or faster data rates, consider the SP3232E or MAX3232 family (3.0V to 5.5V supply). This page synthesizes distributor pricing, drop-in alternatives, application circuit recommendations, and design guidance not consolidated in the manufacturer datasheet.

RFQ Contact
MAX232ACUE+ - 120kbps Dual RS-232 Transceiver | Analog Devices
MAX232ACUE+

MAX232ACUE+ - 120kbps Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX232ACUE+ is a +5 V-powered dual RS-232 transceiver with two drivers and two receivers, a maximum data rate of 120 kbps, and a 16-pin TSSOP package. Its 4.5 V to 5.5 V single-supply operation suits equipment that cannot provide the traditional ±12 V RS-232 interface voltage. The integrated charge-pump circuitry provides the bipolar voltage levels required by RS-232 while the host-side logic operates from a single 5 V rail. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into logic. Within the interface hierarchy, the MAX232 belongs to the RS-232 driver/receiver family, then to the broader transceiver category and ultimately to interface ICs. This device combines two transmit channels with two receive channels, making it suitable for bidirectional point-to-point serial links, console connections, and industrial control equipment. The MAX232ACUE+ supports 120 kbps signaling and uses a 4.5 V to 5.5 V supply. According to the manufacturer product page, the MAX232 family is intended for EIA/TIA-232E and V.28/V.24 communications interfaces where ±12 V is unavailable. The commercial MAX232ACUE+ ordering option is specified for 0 °C to +70 °C operation and is supplied in a gull-wing TSSOP-16 surface-mount package. Each transmit channel converts one TTL/CMOS-compatible input into a bipolar RS-232 output, while each receive channel converts an RS-232 input into a logic-level output. The MAX232 family includes on-chip charge-pump capacitors and driver circuitry, reducing the external component count compared with discrete RS-232 implementations. Exact propagation delay, receiver threshold, output protection, and charge-pump operating-current details should be confirmed in the manufacturer datasheet for the selected ordering option. Typical uses include serial console links, point-to-point data acquisition, test equipment, industrial controllers, and embedded systems communicating with legacy RS-232 devices. For short or low-noise industrial links, the 120 kbps rate provides more than enough margin for many legacy protocols. Longer cables, high common-mode noise, and electrically long interconnects require careful grounding, shielding, and protection planning. Place the MAX232ACUE+ close to the connector or transceiver boundary so the protected RS-232 lines do not run through sensitive digital circuitry. Route ground and signal conductors together where practical, use suitable protection against surge and ESD events, and check that downstream logic levels match the device's input thresholds. The 16-pin TSSOP footprint also requires standard fine-pitch assembly clearance around adjacent components. This product page combines the manufacturer's device information with distributor specifications, replacement cross-references, and practical PCB guidance. It also distinguishes verified device attributes from parameters that require datasheet confirmation, helping engineers evaluate the MAX232ACUE+ and its compatible alternatives more efficiently.

RFQ Contact
MAX232ACUE+T - 5V Dual RS-232 Transceiver | Analog Devices
MAX232ACUE+T

MAX232ACUE+T - 5V Dual RS-232 Transceiver | Analog Devices

Analog Devices MAX232ACUE+T is a 5V-powered, dual RS-232 transceiver with two drivers and two receivers, supplied in a 16-pin TSSOP package. The MAX232ACUE+T designation identifies the commercial-temperature version with gull-wing leads in a rectangular surface-mount package. It is intended for systems that need to translate digital logic levels to and from the voltage, polarity, and drive characteristics required by RS-232 links. An RS-232 transceiver is an interface IC within the broader hierarchy of interface semiconductors, serial communication devices, and data-conversion components. It combines transmit and receive functions in one package: outgoing logic signals pass through line drivers that provide RS-232-compatible levels, while incoming serial signals pass through receivers that convert RS-232 levels back to logic-compatible signals. Integrating both directions simplifies PCB layout in point-to-point serial links, industrial controllers, and service interfaces. The primary identified features are two transmit channels, two receive channels, operation from a 5V supply, and a compact 16-pin TSSOP footprint. The MAX232ACUE+T uses the MAX232 family interface architecture and is intended for commercial-temperature equipment. Its gull-wing terminal arrangement supports conventional surface-mount assembly and inspection after soldering, while the 16-pin package provides a practical size reduction compared with larger through-hole implementations. Technical suitability depends on the voltage levels, data rate, cable length, grounding method, and protection strategy of the connected RS-232 port. Because RS-232 uses single-ended signaling and negative-going voltage levels, the interface must be evaluated together with its charge-pump capacitors, supply bypass, connector protection, and common-mode conditions. The manufacturer datasheet should be used for the complete pin-description table, recommended capacitor values, electrical limits, and operating conditions before layout release. Typical uses include configuration and service ports on industrial equipment, serial links between controllers and peripheral modules, RS-232 test equipment, and legacy communications interfaces retained during product modernization. The device is especially useful where two full-duplex RS-232 channels are required but a larger multi-channel transceiver would be unnecessary. A design should still verify that the selected connector and cable environment match the electrical limits of the interface. PCB layout is a central implementation consideration. Place the required charge-pump and bypass capacitors close to their associated pins, keep the RS-232 driver outputs away from sensitive analog or high-speed logic, and provide an appropriate chassis or signal-ground strategy at the connector. Add transient protection when the cable can be longer than the protected equipment area or exposed to industrial transients. This page organizes the verified product identity, electrical requirements, pin-compatible replacement options, interface applications, and practical RS-232 layout guidance. It helps engineers move from MPN identification to footprint, replacement, and circuit-implementation checks while keeping the final design anchored to the manufacturer datasheet.

RFQ Contact
MAX232ACWE+ - Dual RS-232 Transceiver | Maxim Integrated
MAX232ACWE+

MAX232ACWE+ - Dual RS-232 Transceiver | Maxim Integrated

The Maxim Integrated MAX232ACWE+ is a dual RS-232 line-driver and receiver transceiver packaged in a 16-pin SOIC. It provides two driver channels and two receiver channels for implementing a complete two-channel RS-232 interface from a +5 V supply. The device is intended for EIA/TIA-232E and V.28/V.24 communications interfaces, particularly where bipolar ±12 V supplies are unavailable. An RS-232 transceiver is an interface IC that combines differential line-driver outputs with receiver inputs. It belongs to the communications-interface hierarchy, where a single-ended logic signal is converted into an RS-232-compatible level and an incoming RS-232 signal is converted back into a logic-level voltage. The MAX232ACWE+ uses integrated charge-pump circuitry to generate the positive and negative voltage levels required by the RS-232 line interface. The principal feature is its combination of two transmitters and two receivers in one 16-pin SOIC. This integration reduces the component count and board area required for a dual-port RS-232 connection. The +5 V operating architecture supports equipment designs in which modern digital logic operates from a single positive supply while the external interface still requires RS-232 voltage levels. Operationally, the transmitter section converts TTL or CMOS logic signals into RS-232 levels, while the receiver section performs the inverse conversion. The Maxim Integrated MAX220-MAX249 family documentation identifies this family for EIA/TIA-232E and V.28/V.24 interfaces. The MAX232ACWE+ is therefore appropriate for industrial control links, service-console connections, instrumentation, and embedded systems that communicate with legacy RS-232 equipment. A key design consideration is external bypass capacitance around the charge-pump and supply pins. Place the required capacitors close to their associated package pins, use the shortest practical ground return, and avoid routing the RS-232 driver outputs through unprotected high-impedance nodes. The RS-232 drivers and receivers are intended for wired communication links rather than long-distance high-speed data interfaces. MAX232ACWE+ is identified in current distributor records as a 2/2 full-RS-232 transceiver in a 16-SOIC package. This page combines the manufacturer-family description, package information, cross-reference records, practical interface guidance, and application-specific engineering considerations for engineers evaluating the MAX232ACWE+ or a compatible replacement.

RFQ Contact