Products (21,000+)

PIC24EP512MC204T-I/PT - 16-bit 70MIPS 512KB Flash MCU | Microchip
PIC24EP512MC204T-I/PT

PIC24EP512MC204T-I/PT - 16-bit 70MIPS 512KB Flash MCU | Microchip

The Microchip Technology PIC24EP512MC204T-I/PT is a 16-bit, 70 MIPS dsPIC/PIC24E-family microcontroller with 512 KB of Flash program memory (170K x 24) and 48 KB of RAM, housed in a 44-pin TQFP (PT) 10x10 mm package. It is part of the PIC24EP "Motor Control" sub-family, featuring dedicated on-chip peripherals such as operational amplifiers, comparators, a Peripheral Trigger Generator (PTG), and a Quadrature Encoder Interface (QEI) tailored to high-performance motor-control and digital-power designs. A 16-bit microcontroller (MCU) is a programmable processor that fetches, decodes, and executes instructions whose internal data path is 16 bits wide, offering higher precision and code density than 8-bit parts while remaining easier to use than 32-bit Cortex-M devices. In the broader taxonomy, the PIC24EP sits inside Microchip's dsPIC/PIC24 family of 16-bit microcontrollers, which itself belongs to the wider category of embedded microcontrollers and ultimately to integrated circuits and semiconductors. The PIC24E architecture is built on a modified Harvard core with a 24-bit instruction word, designed to balance deterministic interrupt response with rich DSP-style arithmetic. Key features include 70 MIPS CPU performance from a 70 MHz peripheral clock, 512 KB self-programmable Flash with live update capability, 48 KB SRAM, 4 KB EEPROM emulation, and a 12-bit 1.1 Msps ADC with up to 9 channels and 4 Sample-and-Hold circuits. The device integrates two on-chip op-amps, three analog comparators with a programmable reference, a USB 2.0 full-speed On-The-Go controller, and motor-control PWMs with edge-aligned and center-aligned modes for field-oriented control. Operating voltage is 3.0 V to 3.6 V over an industrial -40 C to +85 C temperature range, with AEC-Q100 variants available in the same silicon for automotive designs. Architecturally, the part combines a high-throughput 16-bit core with motor-control-oriented peripherals and a flexible Peripheral Trigger Generator that allows deterministic, hardware-routed timing between ADC, PWM, and comparator modules without CPU intervention. This makes the PIC24EP512MC204T-I/PT well suited to FOC sensorless motor drives, switched-mode power supplies, and any closed-loop system where deterministic timing and tight ADC-PWM synchronization are required. Typical applications include BLDC/PMSM and ACIM motor-control inverters, uninterruptible power supplies (UPS), digital PFC and LLC power converters, factory automation drives, and precision industrial-servo positioning systems. The PTG and QEI also suit robotics, CNC spindle drives, and encoder-fed motion controllers. The wide operating temperature range and -I grade qualification also support outdoor industrial installations. When designing with this device, allocate adequate decoupling (100 nF + bulk) close to each VDD/VSS pair, route the analog AVSS/AVDD pair as a quiet island separated from digital returns, and observe Microchip's motor-control layout guidelines for the on-chip op-amps and PGA. Always verify errata against the latest silicon revision before committing to high-volume firmware. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes for the PIC24EP512MC204T-I/PT that are not typically collected together on the manufacturer datasheet, supporting faster component selection and BOM risk reduction.

RFQ Contact
PIC24EP512MC206-E/MR - 60 MIPS 16-bit MCU, 512KB Flash | Microchip
PIC24EP512MC206-E/MR

PIC24EP512MC206-E/MR - 60 MIPS 16-bit MCU, 512KB Flash | Microchip

The Microchip Technology PIC24EP512MC206-E/MR is a 16-bit microcontroller from the PIC24EP motor-control family, delivering up to 70 MIPS CPU performance (60 MIPS sustained throughput) with 512 KB Flash and 48 KB RAM, housed in a 64-pin QFN package (9x9 mm) with exposed pad. Designed for high-performance precision motor control, it integrates dedicated motor-control peripherals including a Quadrature Encoder Interface (QEI), Motor Control PWM (MCPWM), and high-speed 10/12-bit ADC, all of which reduce external component count in BLDC, PMSM, and ACIM drive designs. AEC-Q100 qualification makes this part suitable for automotive motor-control applications. A 16-bit microcontroller (MCU) is a programmable computing device that executes arithmetic on 16-bit-wide data words in a single instruction, sitting between 8-bit microcontrollers and 32-bit ARM Cortex-M devices in both performance and cost. Within the broader taxonomy, the PIC24EP belongs to: microcontroller -> embedded MCU -> DSP-enabled MCU -> motor-control MCU -> automotive MCU. Its 16-bit DSC (Digital Signal Controller) heritage gives it native fractional arithmetic and single-cycle MAC operations, which are valuable for real-time control loops running in the kHz range. Key features include a 3.0 V to 3.6 V single-supply operating range, 53 general-purpose I/O pins, USB 2.0 Full-Speed On-The-Go with integrated PHY, two CAN 2.0B modules, four UART/SPI/I2C peripherals, a Parallel Master Port (PMP), a 16-bit asynchronous Timer, and a charge-pump function. On-chip op amps simplify current-sensing signal conditioning in FOC motor control. The Instruction Trace (PSV) and multiple interrupt vectors accelerate real-time debugging. The CPU core uses a modified Harvard architecture with separate 24-bit instruction and 16-bit data paths, executing most instructions in a single cycle. Internal PLL supports up to 140 MHz FOSC from an external 7.37 MHz crystal. The 24KB RAM area is split between general-purpose SRAM and DMA-accessible buffers, supporting dual-port RAM for USB endpoint memory. Typical applications include sensorless and sensored BLDC/PMSM motor drives, automotive HVAC blowers and pumps, field-oriented control (FOC) inverters, factory-automation servo drives, drone ESCs, and industrial variable-frequency drives. The combination of QEI + MCPWM + 12-bit 1.1 Msps ADC allows the part to drive three-phase bridges with sub-microsecond dead-band control without external DSP. When designing with this device, allocate the exposed pad (EP) to a continuous ground copper pour with at least 25 thermal vias to dissipate switching-converter heat. Decouple VDD/VSS pairs with 100 nF + 4.7 uF ceramics placed within 3 mm of each pin pair. The MCPWM has a programmable dead-band range of 1-64 Tcy; verify the dead time against IGBT/MOSFET turn-off delay to prevent shoot-through. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical motor-control design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC24EP512MC206-E/PT - 70 MIPS 512KB Flash Motor Control MCU | Microchip
PIC24EP512MC206-E/PT

PIC24EP512MC206-E/PT - 70 MIPS 512KB Flash Motor Control MCU | Microchip

The Microchip Technology PIC24EP512MC206-E/PT is a 16-bit MCU from the PIC24EP family with integrated motor-control peripherals, 512 KB of Flash program memory, 48 KB RAM, and a 64-pin TQFP package. Designed for high-performance, precision motor-control applications, it executes instructions at up to 70 MIPS from a 60 MHz system clock, with on-chip dual 40 MHz op amps, a 12-bit ADC at 500 ksps, and dedicated PWM/QEI modules for field-oriented control of brushless DC, PMSM, AC induction, and stepper motors. What is a motor-control MCU? A motor-control microcontroller is an embedded processor that integrates the CPU with motor-control-specific peripherals such as high-resolution PWM timers, quadrature encoder interfaces, fast ADCs for current sensing, and analog comparators for hardware overcurrent protection. The PIC24EP512MC206-E/PT combines these peripherals on-chip to reduce external component count, lower BOM cost, and tighten the control loop latency below 100 microseconds, which is essential for sinusoidal commutation and torque-ripple minimization. Key features include AEC-Q100 qualification (extended grade), an extended -40C to +125C operating temperature range, 5 op-amp pairs, dual 4-channel high-speed PWM outputs with 7.14 ns resolution, three quadrature encoder interfaces, and USB-OTG, SPI, I2C, and UART connectivity. The integrated peripherals reduce the need for external signal-conditioning components, enabling compact BLDC and PMSM inverter designs. The PIC24EP architecture uses a 16-bit modified Harvard core with a 24-bit instruction word and DSP extensions. The DSP engine accelerates field-oriented-control algorithms such as Park and inverse-Park conversions, space-vector PWM, and PID controllers, enabling single-MCU FOC implementation for sensorless or sensored BLDC drives up to several kilowatts. Typical applications include sensorless and sensored BLDC/PMSM motor drives, industrial servo control, HVAC blowers and pumps, electric-vehicle auxiliary motors, e-bike and drone ESC controllers, and robotic actuator control loops. The -E temperature grade and AEC-Q100 qualification extend suitability to automotive under-hood and industrial environments. When designing with this device, verify the timing relationship between the PWM module and the ADC sampling trigger to achieve deterministic current sampling. The integrated op amps require careful PCB layout near the MCU; keep analog ground returns short to avoid coupling PWM switching noise into the current-sense path. This page synthesizes XAIPART distributor pricing, drop-in same-brand alternatives, and practical motor-control design guidance not consolidated on any single manufacturer or distributor page.

RFQ Contact
PIC24EP512MC206-H/MR - 16-Bit 60MIPS 512KB Flash Motor Control MCU | Microchip
PIC24EP512MC206-H/MR

PIC24EP512MC206-H/MR - 16-Bit 60MIPS 512KB Flash Motor Control MCU | Microchip

The Microchip PIC24EP512MC206-H/MR is a high-performance 16-bit microcontroller from the PIC24E Motor Control family, delivering 70 MIPS at up to 60 MHz CPU clock and integrating 512 KB of Flash program memory with 48 KB of RAM in a 64-pin QFN (9x9 mm) package with an exposed thermal pad. The "-H" suffix denotes the high-temperature grade (-40C to +150C operating range), making it suitable for under-hood automotive and harsh industrial environments. The "MR" package code identifies the 64-pin QFN-EP. What is a motor-control MCU? A motor-control microcontroller (MCU) is a specialized 16-bit or 32-bit processor integrating timers, PWMs, ADCs, and quadrature encoder interfaces (QEI) to drive brushless DC, permanent-magnet synchronous, AC induction, and switched-reluctance motors in closed-loop control. In the embedded hierarchy, the PIC24EP512MC206 sits within: microcontroller -> 16-bit MCU -> dsPIC/PIC24 family -> motor-control peripheral set -> Microchip PIC24E series. This integrated approach replaces discrete DSPs and external PWM controllers, shrinking BOM and improving loop bandwidth. Key features of this part include: up to six PWM channels with complementary outputs and dead-band control; three op-amps for current sensing; four 16-bit timers; three UART, two SPI, two I2C peripherals; up to 16 channels of 10-bit ADC at 1.1 Msps or 12-bit ADC at 500 ksps; a Quadrature Encoder Interface (QEI); and a Peripheral Trigger Generator (PTG) for synchronizing ADC sampling to PWM events. The 60 MIPS performance enables field-oriented control (FOC) of three-phase PMSM motors with sub-microsecond current-loop execution. The device's Enhanced Motor Control PWM (MCPWM) module features 7.14 ns PWM resolution, independent fault inputs, and PWM-triggered ADC conversions for deterministic sampling. Combined with the on-chip op-amps and a high-speed 12-bit ADC, the MCU can sample phase currents, execute a FOC loop, and update PWM duty cycles entirely on-chip - eliminating external DSPs in motor-drive designs. Typical applications include field-oriented control (FOC) of PMSM/BLDC motors in industrial servo drives, ceiling fans and pumps, e-bike traction controllers, HVAC blowers, and automotive auxiliary pumps. The wide 3.0V-3.6V supply range and integrated peripherals simplify BOM and reduce time-to-market. When designing with this device, use the MPLAB X IDE with the MPLAB Code Configurator (MCC) for automatic peripheral initialization. The exposed thermal pad must be soldered to a sufficient copper pour for heat dissipation; the -H temperature grade allows operation up to +150C junction. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes beyond what the manufacturer datasheet alone provides.

RFQ Contact
PIC24EP512MC206-I/PT - 70 MIPS 512KB Flash Motor Control MCU | Microchip
PIC24EP512MC206-I/PT

PIC24EP512MC206-I/PT - 70 MIPS 512KB Flash Motor Control MCU | Microchip

The Microchip Technology PIC24EP512MC206-I/PT is a high-performance 16-bit PIC24E microcontroller delivering 70 MIPS of computational throughput, 512 KB of Flash program memory, and 48 KB of RAM in a 64-pin TQFP (10x10 mm) package. The device integrates dedicated motor-control peripherals including a Quadrature Encoder Interface (QEI), Motor Control PWM (MCPWM) modules, and on-chip operational amplifiers, enabling single-chip precision drives for BLDC, PMSM, ACIM, and stepper motors. A 16-bit MCU (Microcontroller Unit) is a class of embedded processor that balances deterministic real-time performance with rich peripheral integration. Within the broader taxonomy, the PIC24E family is a digital signal controller (DSC) class device — hybrid MCUs that combine microcontroller ease-of-use with DSP-class throughput for sensor-rich, closed-loop applications. As part of Microchip's PIC24E motor-control family, this part targets high-end motion-control designs where code density, deterministic interrupt latency, and dedicated motor-control hardware reduce or eliminate the need for external FPGAs or DSP coprocessors. Key specifications include 70 MIPS core speed at 60 MHz CPU clock, 512 KB Flash (170K x 24), 48 KB SRAM, dual 10-bit and 12-bit ADC modules, communication peripherals (I2C, SPI, UART, LIN, IrDA), and an extended operating voltage range of 3.0 V to 3.6 V with industrial -40 C to +85 C temperature support. Internal op-amps eliminate external signal conditioning for current sensing, while hardware QEI simplifies encoder-based position feedback. Architecturally, the PIC24E uses a modified Harvard bus with a 24-bit instruction word, single-cycle hardware MAC, and zero-cycle hardware divide, achieving DSP-class signal-processing throughput while retaining 16-bit MCU code density. The on-chip CTMU (Charge Time Measurement Unit) supports capacitive touch and time-based sensing. Peripheral Trigger Generator (PTG) coordinates complex peripheral sequences without CPU intervention. Typical applications include field-oriented control (FOC) motor drives, sensorless and sensored BLDC/PMSM controllers, industrial servo amplifiers, fan/pump controllers, robotic actuators, and HVAC compressor drives. Designers favor the part for its deterministic interrupt latency, integrated op-amps for current shunt amplification, and hardware QEI for resolver-free encoder feedback. When designing with this MCU, allocate sufficient decoupling (100 nF ceramic per VDD/AVDD pair plus bulk) and follow the recommended PCB layout for the analog and digital ground split. For high-noise motor environments, the MCPWM dead-time control and fault input pin allow cycle-by-cycle shutdown on over-current without CPU latency. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from the same PIC24E family, and practical design notes drawn from Microchip application notes — content not consolidated in any single manufacturer datasheet.

RFQ Contact
PIC24EP512MC206T-E/MR - 16-Bit 60MIPS 512KB Flash MCU | Microchip
PIC24EP512MC206T-E/MR

PIC24EP512MC206T-E/MR - 16-Bit 60MIPS 512KB Flash MCU | Microchip

The Microchip Technology PIC24EP512MC206T-E/MR is a 16-bit PIC24E microcontroller delivering up to 60 MIPS of CPU performance with 512 KB (170K x 24-bit) of Flash program memory and 48 KB of SRAM, packaged in a 64-pin 9x9 mm VQFN (MR) with exposed thermal pad. It is qualified to the AEC-Q100 automotive standard and operates from a 3.0-3.6 V rail, targeting motor-control and high-end embedded applications. The "T" suffix denotes tape-and-reel packaging, and "E" denotes the -40C to +125C extended/automotive temperature grade. What is a PIC24E microcontroller? The PIC24E is Microchip's 16-bit enhanced MCU family, positioned in the taxonomy as 16-bit microcontroller -> dsPIC DSC -> PIC microcontroller family -> Microchip 8/16/32-bit MCU portfolio -> embedded processing. PIC24E devices combine a Harvard-architecture DSP-enhanced CPU, high-speed ADC, motor-control PWM, op-amps, comparators, and a Charge Time Measurement Unit (CTMU) in a single chip, sitting between 8-bit PIC10/12/16/18 MCUs and 32-bit PIC32MX/PIC32MZ MCUs. They are commonly used where deterministic real-time control and DSP math are required without the overhead of a 32-bit core. The PIC24EP512MC206T-E/MR integrates a 16-channel 10-bit ADC (configurable up to 12-bit on selected variants), a 70 MIPS dsPIC-style DSP engine, dedicated motor-control peripherals (3 op-amps, 4 comparators, PWM with fault inputs and quadrature encoder interface), and supports I2C, SPI, UART, LIN, and IrDA. The 64-pin QFN-9x9 footprint includes a thermal pad that pulls dual function as both the analog ground reference and the primary heat-dissipation path. The family is the recommended Microchip platform for FOC, BLDC, PMSM, and PFC motor-control designs. Typical applications include BLDC/PMSM motor drives, industrial automation PLCs, automotive body controllers, sensorless field-oriented control, LED lighting controllers, and digital power conversion (PFC/LLC). For motor-control applications the integrated op-amp/comparator chain reduces BOM and PCB area compared with discrete analog front-ends. Design consideration: when routing the PCB, tie the exposed pad directly to AGND with at least 16 thermal vias to a 1 oz copper inner plane. For best ADC SNR results keep the analog and digital ground planes physically separate and join them at a single point under the QFN thermal pad. The T-variant tape-and-reel pack and the E-grade extended temperature make this part specifically suited to high-volume automotive production lines. This page combines distributor pricing, drop-in same-brand alternatives (PIC24EP512GP206 family), application references, and design notes into a single technical hub not found on the standalone Microchip datasheet, helping procurement, EE hardware, and firmware engineers accelerate motor-control design-in and BOM consolidation decisions.

RFQ Contact
PIC24EP512MC206T-I/PT - 70 MIPS 16-bit Motor Control MCU | Microchip
PIC24EP512MC206T-I/PT

PIC24EP512MC206T-I/PT - 70 MIPS 16-bit Motor Control MCU | Microchip

The Microchip PIC24EP512MC206T-I/PT is a 16-bit MCU from the PIC24EP family designed for high-performance motor control and digital signal control. It operates up to 70 MIPS with a 60 MHz CPU clock, integrates 512 KB (170K x 24) of Flash program memory and 48 KB RAM, and is housed in a 64-pin TQFP (PT) package rated -40C to +85C industrial temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (RAM), and configurable peripherals such as timers, ADC, PWM, and communication interfaces. Within the product hierarchy, the PIC24EP sits between 8-bit PIC MCUs and 32-bit ARM Cortex-M devices, and belongs to the broader class of digital signal controllers (DSCs) that combine deterministic control peripherals with DSP-class throughput for closed-loop applications. Key features include integrated Motor Control PWM (MCPWM) with up to 14 PWM channels, a Quadrature Encoder Interface (QEI) for rotor position feedback, dual 10-bit/12-bit ADC modules, internal op-amps and comparators, CTMU charge-time measurement, and USB-OTG plus CAN, SPI, I2C, and UART interfaces. The 512 KB Flash and 48 KB RAM support large firmware for sensorless FOC and field-oriented control algorithms. The architecture uses a modified Harvard core with single-cycle 16x16 MAC, hardware DO/REPEAT loops, and zero-overhead interrupt nesting - enabling deterministic execution of high-rate control loops. Internal DSP acceleration and 70 MIPS throughput make it well suited for both trapezoidal and field-oriented BLDC/PMSM control schemes. Typical applications include BLDC and PMSM motor drives, industrial inverters, field-oriented control (FOC) drives, sensorless motor control, robotics, servo amplifiers, and home appliances. The wide temperature range and rich motor peripherals enable compact, energy-efficient motor designs. When designing with this device, allocate PCB area for the 64-pin TQFP land pattern and follow Microchip's analog-ground and decoupling guidance. The internal op-amps reduce BOM cost, but external filtering is recommended for noisy motor environments. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and motor-control design considerations not compiled in the manufacturer datasheet.

RFQ Contact
PIC24EP64GP202-E/MM - 16-Bit 60 MIPS MCU, 64KB, 28-QFN | Microchip
PIC24EP64GP202-E/MM

PIC24EP64GP202-E/MM - 16-Bit 60 MIPS MCU, 64KB, 28-QFN | Microchip

The Microchip Technology PIC24EP64GP202-E/MM is a 16-bit microcontroller from the PIC24E general-purpose MCU family, delivering up to 70 MIPS core performance with 64 KB of Flash program memory (22K x 24) and housed in a 28-pin QFN-S (6x6 mm) package with exposed pad. The device operates from a 3.0 V to 3.6 V supply, supports 60 MHz operation, and integrates high-performance peripherals for demanding embedded applications. What is a PIC24E microcontroller? A PIC24E MCU is a 16-bit Harvard-architecture microcontroller from Microchip that sits in the dsPIC/PIC24 family hierarchy (16-bit MCU -> microcontroller -> embedded IC -> semiconductor). Compared with 8-bit PIC MCUs, the PIC24E delivers a much higher MIPS-per-MHz ratio, wider 16-bit data path, hardware multiply/divide, larger linear address space, and DSP-oriented instruction support, making it the bridge between 8-bit PIC16/18 designs and full dsPIC33 digital signal controllers. Key features include 8 KB SRAM, integrated op amps, a Charge Time Measurement Unit (CTMU) for capacitive touch and accurate time measurement, a Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing, and superior ADC performance for precision analog designs. The 28-QFN package exposes a thermal pad for low theta_JA operation and supports up to 21 general-purpose I/O pins plus peripheral functions such as UART, SPI, I2C, PWM, and a 10/12-bit ADC. Typical applications span industrial control, motor drive, LED lighting, power conversion, sensor conditioning, USB device interfaces (with companion parts), medical instrumentation, and AEC-Q100 automotive subsystems where the -E (extended temperature, -40°C to +125°C) variant is required. When designing with this MCU, ensure the 3.3V rail is decoupled with a 100 nF + 10 µF combination close to the VDD pins and that the exposed pad is soldered to a sufficient copper pour for thermal relief. The PGECx/PGEDx pair must be reserved for ICSP unless the debugger is disabled in configuration bits. This page synthesizes distributor pricing, drop-in same-family PIC24E alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and design engineers make faster, more informed decisions.

RFQ Contact
PIC24EP64GP202-E/SO - 16-Bit 60 MIPS 64KB Flash MCU | Microchip
PIC24EP64GP202-E/SO

PIC24EP64GP202-E/SO - 16-Bit 60 MIPS 64KB Flash MCU | Microchip

The Microchip PIC24EP64GP202-E/SO is a 16-bit microcontroller from the PIC24EP family, featuring a 60 MIPS (70 MHz) dsPIC/PIC24E core with 64 KB Flash program memory and 8 KB RAM, housed in a 28-pin SOIC (SO) wide-body package. It is qualified to the AEC-Q100 automotive standard, runs from a single 3.0 V to 3.6 V supply, and offers 21 general-purpose I/O pins plus enhanced analog peripherals including operational amplifiers, a Charge Time Measurement Unit (CTMU), and a Peripheral Trigger Generator (PTG). A PIC microcontroller (Programmable Interface Controller) is a Harvard-architecture RISC MCU widely used for embedded control, combining a CPU, Flash program memory, SRAM, EEPROM, timers, ADC, and digital I/O on a single die. Within Microchip's hierarchy it sits in the PIC24E general-purpose family - the "EP" suffix denotes Enhanced Performance with op-amps and CTMU, and "GP" denotes General Purpose variants rather than motor-control or USB-focused siblings. Key features include a 16-channel 10-bit ADC capable of 500 ksps, a 12-channel 16-bit PWM/timer/capture module, op-amp peripherals, a USB 2.0 full-speed On-The-Go interface, and multiple serial interfaces (UART, SPI, I2C). The 70 MIPS execution throughput and 16-bit data path enable efficient DSP-style math (single-cycle MAC) for sensor fusion and digital filtering tasks. Architecturally the PIC24EP64GP202 uses a 24-bit instruction word with 16-bit data paths and dual-bus Harvard design, giving deterministic interrupt latency and predictable code execution. The integrated op-amps, CTMU, and PTG offload analog signal-chain work from the CPU and let peripherals trigger each other without software overhead. Typical applications include automotive body and sensor nodes, industrial motor-control auxiliary boards, sensor-conditioning front ends, USB device firmware, and portable instrumentation. The combination of op-amps + ADC + USB is unusually strong for signal-chain firmware development. When designing with this part, note that the E suffix indicates -40C to +125C automotive temperature grade and the SO package is 7.50 mm wide-body SOIC. Apply proper decoupling, follow Microchip's recommended layout for the USB DP/DM lines, and configure unused pins as outputs per the datasheet to minimize current draw. This page synthesizes distributor pricing, AEC-Q100 cross-reference notes, and practical design guidance not present in the bare datasheet PDF.

RFQ Contact
PIC24EP64GP202-E/SS - 16-Bit 60 MIPS 64KB Flash MCU | Microchip
PIC24EP64GP202-E/SS

PIC24EP64GP202-E/SS - 16-Bit 60 MIPS 64KB Flash MCU | Microchip

The Microchip Technology PIC24EP64GP202-E/SS is a 16-bit microcontroller from the PIC24EP "GP" general-purpose family, delivering 60 MIPS performance from a 70 MIPS-capable core, with 64 KB (22K x 24) of Flash program memory and 4 KB RAM in a 28-pin SSOP package. The "E" suffix denotes the extended industrial temperature grade (-40C to +125C), and the device targets high-end general-purpose designs needing advanced analog, high-speed PWM, and rich connectivity. This device belongs to the broader microcontroller (MCU) category, which in a system hierarchy sits below microprocessors but above discrete digital logic; the PIC24EP family specifically is a 16-bit Harvard-architecture MCU family from Microchip, positioned between 8-bit PIC16/PIC18 parts and 32-bit PIC32 parts. MCUs integrate CPU core, program memory (Flash), data memory (RAM), peripherals, and I/O onto a single IC, replacing multi-chip discrete logic implementations. Key features of the PIC24EP64GP202-E/SS include a 16-bit modified Harvard core with single-cycle MAC, 64 KB self-programmable Flash with ECC, 4 KB SRAM, integrated op-amps, a Charge Time Measurement Unit (CTMU), a Peripheral Trigger Generator (PTG), and a high-performance 10/12-bit ADC. The 28-SSOP package keeps the design compact while exposing 21 general-purpose I/O pins. The 3.0 V to 3.6 V single-supply operation simplifies power-tree design. Typical applications include industrial control, motor drive (BLDC/PMSM) commutation, sensor signal conditioning, USB-device nodes, SMPS digital control, and AEC-Q100 automotive subsystems. The combination of op-amps and CTMU on-chip reduces the external analog chain, lowering BOM cost and PCB area. For power-budgeting, remember that core MIPS draw is strongly tied to CPU utilization; gate unused peripherals via PMD registers to hit deep sleep currents. Place a 0.1 uF decoupling capacitor within 5 mm of every VDD/VSS pair and use a bulk 4.7 uF tantalum or ceramic close to the IC for ADC reference stability. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet.

RFQ Contact
PIC24EP64GP202-I/MM - 16-Bit 70 MIPS MCU, 64KB Flash | Microchip
PIC24EP64GP202-I/MM

PIC24EP64GP202-I/MM - 16-Bit 70 MIPS MCU, 64KB Flash | Microchip

The Microchip Technology PIC24EP64GP202-I/MM is a 16-bit microcontroller from the PIC24EP GP family, delivering 70 MIPS of CPU performance from a modified Harvard architecture core running up to 70 MHz (with 60 MHz FOSC cited in some distributor summaries). Housed in a 28-pin QFN-S 6x6 mm package with an exposed thermal pad, the device integrates 64 KB of Flash program memory (22K x 24 words) and 8 KB of SRAM, and operates from a 3.0 V to 3.6 V supply. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (typically Flash), data RAM, and a rich set of peripherals on one silicon die. The PIC24EP family sits in Microchip's 16-bit DSC/MCU portfolio, hierarchically placed above 8-bit PIC16/PIC18 MCUs and below the 32-bit PIC32 families. This part is targeted at high-end general-purpose embedded designs that need more compute and analog performance than 8-bit MCUs but do not justify migrating to a 32-bit core. Key features include a 12-bit ADC with up to 10/12 Msps sampling (family capability), dedicated op amps, a Charge Time Measurement Unit (CTMU) for touch and capacitive sensing, a Peripheral Trigger Generator (PTG) for hardware-event sequencing, and a 16-bit motor-control PWM peripheral, alongside USB 2.0 full-speed On-The-Go on related family members. The architecture combines a 16-bit data path with 24-bit instructions, which improves code density relative to 32-bit cores and eases C compiler efficiency. Internal PLLs allow the core to run faster than the external crystal. The 28-QFN-S package includes a thermal pad for improved heat dissipation in industrial temperature ranges (-40 C to +85 C for this -I grade). Typical applications include industrial control boards, sensor signal conditioning, USB peripherals, motor-control companion logic, and general-purpose 16-bit embedded platforms where analog integration (ADC, op amps, CTMU) reduces external component count. When designing with this device, allocate ADC and op-amp pinout early and follow Microchip's analog-ground PCB guidelines (separate AGND/AVSS pour, decouple Vcap/Vddcore). The Peripheral Trigger Generator requires MPLAB X IDE plugin configuration, and op-amp input ranges must respect rail-to-rail limits. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from the same PIC24EP family, and practical design notes not consolidated in the manufacturer datasheet.

RFQ Contact
PIC24EP64GP202-I/SO - 70 MIPS 64KB Flash MCU | Microchip
PIC24EP64GP202-I/SO

PIC24EP64GP202-I/SO - 70 MIPS 64KB Flash MCU | Microchip

The Microchip Technology PIC24EP64GP202-I/SO is a 16-bit PIC24E general-purpose microcontroller with a 70 MIPS high-speed core, 64 KB of Flash program memory and 8 KB of SRAM, packaged in a 28-pin SOIC. The device combines a high-performance CPU with integrated analog resources including operational amplifiers, comparators, CTMU and the Peripheral Trigger Generator, making it suitable for embedded control, sensing and signal-processing systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, digital I/O and peripherals on one device. The PIC24EP64GP202 belongs to the PIC24E family of 16-bit general-purpose MCUs, a category positioned between simple 8-bit controllers and more complex 32-bit application processors. This device provides the processing performance and analog integration needed to consolidate functions that otherwise require separate analog and digital components. Key features include the 70 MIPS CPU core, 64 KB of Flash program memory organized as 22K × 24 words, and 8 KB of SRAM. Its integrated analog resources include three operational amplifiers, four comparators, CTMU and the Peripheral Trigger Generator. These resources support measurement, conditioning, motor-control, feedback and event-timing functions while reducing external component count. The listed operating supply range is 3.0 V to 3.6 V. The PIC24E core combines a 16-bit architecture with a high-speed peripheral set and strong code density. The 28-pin SOIC provides 83 I/O according to the device listing, allowing simultaneous digital communication, control outputs and analog signal inputs where board routing permits. The integrated operational amplifiers and comparators can implement instrumentation and closed-loop control functions, while CTMU assists capacitive measurement and timing applications. Typical applications include industrial sensor interfaces, precision control systems, motor and actuator controllers, laboratory equipment and embedded measurement products. The device is especially useful when analog conditioning, threshold detection and deterministic control must share a compact platform. Designers should allocate pins for programming and debugging, keep analog and digital return currents separated, and verify every peripheral connection against the manufacturer pin-description table. The industrial-grade ordering code is intended for operation across an extended commercial temperature range, while the SO package supports conventional surface-mount assembly. Careful PCB planning should provide a continuous ground plane, short analog routes and adequate decoupling at each supply pin. Decoupling capacitor selection and placement should follow the manufacturer’s recommended application circuit and layout guidance. This product overview combines the device’s processing, memory and analog capabilities with practical sourcing, comparison and design guidance. It identifies the exact ordering code and package while helping engineers determine whether the PIC24EP64GP202-I/SO fits a compact, analog-rich embedded control design.

RFQ Contact
PIC24EP64GP202-I/SP - 70 MIPS 64KB Flash 16-bit MCU | Microchip
PIC24EP64GP202-I/SP

PIC24EP64GP202-I/SP - 70 MIPS 64KB Flash 16-bit MCU | Microchip

The Microchip Technology PIC24EP64GP202-I/SP is a 16-bit microcontroller from the PIC24EP general-purpose MCU family, featuring a high-speed 70 MIPS core, 64 KB of Flash program memory, 8 KB of SRAM, and a 28-pin SPDIP (Skinny Plastic DIP) package. Operating from 3.0V to 3.6V, it integrates advanced features such as a Peripheral Trigger Generator (PTG), Charge Time Measurement Unit (CTMU), three on-chip op-amps, four comparators, and superior ADC performance for high-end general-purpose embedded designs. A 16-bit microcontroller (MCU) is a microprocessor core with a 16-bit data path, ALU, and register width that balances computational throughput against code density. The PIC24EP series uses a modified Harvard architecture with separate program and data buses plus DSP extensions, positioning it above 8-bit MCUs in the hierarchy (8-bit MCU -> 16-bit MCU -> 32-bit MCU) while remaining below dedicated DSP controllers. It is widely used for motor control, power conversion, sensor fusion, and real-time control loops where deterministic interrupt response and rich analog peripherals are required. Key features of the PIC24EP64GP202 include 64 KB (22K x 24) Flash, 8 KB RAM, a 16-channel 12-bit ADC with up to 500 ksps conversion rate, three op-amps for signal conditioning, four comparators for fast threshold detection, four general-purpose 16-bit timers, and a Peripheral Trigger Generator that automates peripheral sequencing without CPU intervention. The device supports communication interfaces including UART, SPI, and I2C. The architecture combines a 16-bit CPU with DSP instructions and a hardware multiplier for single-cycle MAC operations. The CTMU allows precise time measurement for capacitive touch and current sensing, while the PTG can orchestrate peripheral events to offload timing-critical tasks. This blend makes the PIC24EP64GP202 well suited for sensor interfacing and closed-loop control. Typical applications include industrial motor control, sensor signal conditioning, power conversion, capacitive touch human-machine interfaces, and embedded control systems requiring 16-bit performance at moderate cost. The wide operating temperature range of -40C to +85C supports industrial and consumer environments. When designing with this MCU, plan for adequate decoupling with 100 nF ceramic capacitors near each VDD pin, ensure the MCLR reset circuit follows Microchip reference design guidelines, and reserve the PGxI for ISP programming access. The 70 MIPS performance requires a stable clock source and proper layout for EMI-sensitive applications. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in alternative MPNs from the same PIC24EP family, and practical design considerations not found in the manufacturer datasheet alone.

RFQ Contact
PIC24EP64GP202-I/SS - 16-Bit 70 MIPS MCU, 64KB Flash | Microchip
PIC24EP64GP202-I/SS

PIC24EP64GP202-I/SS - 16-Bit 70 MIPS MCU, 64KB Flash | Microchip

The Microchip Technology PIC24EP64GP202-I/SS is a 16-bit microcontroller from the PIC24EP general-purpose family, featuring a 70 MIPS high-performance core, 64 KB (22K x 24) of Flash program memory, 8 KB of RAM, and housed in a 28-pin SSOP (5.30 mm body width, 0.65 mm pitch) package. The device operates from 3.0 V to 3.6 V and delivers up to 70 MIPS at 70 MHz CPU clock, integrating 21 analog channels of 10/12-bit ADC, multiple UART/SPI/I2C peripherals, and CTMU (Charge Time Measurement Unit) plus on-chip op-amps for advanced analog front-end designs. A 16-bit MCU is a microcontroller whose data path, registers, and ALU natively operate on 16-bit words, doubling the throughput and code density of 8-bit devices such as PIC18 while keeping deterministic interrupt latency. Within the broader semiconductor hierarchy, the PIC24EP sits above PIC24F/dsPIC33F performance parts and below 32-bit ARM Cortex-M families; it is optimized for real-time control loops, mixed-signal conditioning, and motor control where deterministic DSP-style instructions matter. Key features include 21 ADC channels at up to 500 ksps (10-bit mode), 6 general-purpose timers, Peripheral Trigger Generator (PTG) for automated peripheral sequencing, dual comparators with 32-bit capture, and a Peripheral Pin Select (PPS) system that maps digital peripherals to a wide choice of I/O pins. The CTMU and integrated op-amps enable touch sensing, capacitive measurement, and current-loop signal conditioning without external analog ICs. The PIC24EP64GP202 architecture uses a modified Harvard structure with separate program (Flash) and data (SRAM) buses, a hardware multiplier/divider, and DSP-aware instructions for motor-control and digital-filter math. PPS routing, dual-partition Flash with live update, and JTAG/ICSP debug support round out the silicon, while the SSOP-28 footprint targets hand-solder-friendly prototyping as well as volume SMT assembly. Typical applications include industrial sensor conditioning, BLDC/PMSM motor control, general-purpose digital power conversion, USB device/host stacks (with companion parts), and consumer audio or appliance controllers. The wide ADC channel count and on-chip op-amps make it a strong fit for instrumentation front-ends that previously needed a separate analog SoC. When designing with this part, plan I/O assignments through the PPS system before PCB layout, and provision external bulk capacitance near VDD/VSS because simultaneous ADC and PWM switching can pull transients beyond the on-chip decoupling. Use the PTG to offload deterministic peripheral timing from the CPU and free cycles for control loops. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PIC24EP64GP202T-E/MM - 16-bit MCU 64KB Flash 60MHz 28-QFN | Microchip
PIC24EP64GP202T-E/MM

PIC24EP64GP202T-E/MM - 16-bit MCU 64KB Flash 60MHz 28-QFN | Microchip

The Microchip Technology PIC24EP64GP202T-E/MM is a 16-bit PIC24EP general-purpose microcontroller delivering 60 MIPS performance with 64KB Flash and 8KB SRAM in a 28-pin QFN-S (6x6 mm) package. The device integrates a high-speed modified Harvard architecture core, 12-bit ADC, op amps, CTMU, USB, and Peripheral Trigger Generator for advanced analog signal-chain applications. A 16-bit microcontroller is a single-chip computer that processes data and instructions in 16-bit chunks, offering a middle ground between 8-bit simplicity and 32-bit computational power. PIC24E-family MCUs sit within the broader taxonomy of microcontroller -> embedded processor -> semiconductor device. They are widely used where the arithmetic precision of a 16-bit DSP-like core is needed without paying the cost or power overhead of 32-bit Cortex-M parts. The PIC24EP64GP202 provides 64KB of program memory (22K x 24 instruction words), 8KB SRAM, and runs from a 3.0V to 3.6V single supply. Up to 21 general-purpose I/O pins are available on the 28-QFN variant, alongside nine 16-bit timers, multiple UART/SPI/I2C peripherals, USB 2.0 full-speed OTG, and a 12-bit 1.1 Msps ADC with up to 13 input channels. The on-chip op amps and CTMU simplify touch and analog-front-end designs. Architecturally the part uses a 16-bit modified Harvard core with single-cycle MAC, hardware DIV, and zero-overhead looping, which yields deterministic cycle-time DSP-style signal chains. Code density is enhanced by a variable-length instruction format, and the peripheral trigger generator (PTG) coordinates complex timer-driven sequences without CPU intervention. Typical applications include industrial motor control (BLDC, PMSM, stepper), USB peripherals and Human Interface Devices, digital sensor signal conditioning, LED lighting controllers, and low-power IoT edge nodes. The wide operating temperature range (-40C to +125C) suits industrial environments, while the USB 2.0 FS OTG supports CDC, HID, MSD, and vendor-class firmware. When designing with this part, verify the VDD/VUSB rail sequencing, route the analog AVdd/AVss pins with separate ferrite isolation, and place the 28-QFN thermal pad on a continuous copper pour with at least 4 thermal vias for heat extraction. The 'T' suffix designates Tape & Reel packaging, and the 'E' suffix denotes the -40C to +125C extended industrial temperature grade. This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC24EP family, and practical design notes drawn from Microchip application notes, offering an information-gain perspective not contained in the standalone datasheet.

RFQ Contact
PIC24EP64GP202T-I/SS - 70 MIPS 16-bit MCU 64KB Flash | Microchip
PIC24EP64GP202T-I/SS

PIC24EP64GP202T-I/SS - 70 MIPS 16-bit MCU 64KB Flash | Microchip

The Microchip Technology PIC24EP64GP202T-I/SS is a 16-bit microcontroller built around the PIC24E high-performance core running at up to 70 MIPS (instruction execution rate), housed in a 28-pin SSOP (5.30 mm) package. The part integrates 64 KB of flash program memory (22K x 24 words), 8 KB of SRAM, and a CTMU (Charge Time Measurement Unit) plus on-chip op-amps and comparators for analog signal conditioning. The "/SS" suffix denotes the SSOP-28 package, while "I" specifies the industrial -40C to +85C operating temperature range; the trailing "T" indicates Tape and Reel packaging. Operating voltage is 3.0 V to 3.6 V from a single supply, making it suited to 3.3 V embedded designs. A 16-bit microcontroller (MCU) is a programmable logic device with a 16-bit datapath, registers, and arithmetic logic unit, falling within the broader categories of embedded controller -> microcontroller -> integrated circuit -> semiconductor. The PIC24E family sits between 8-bit PIC MCUs and 32-bit PIC32 devices in the Microchip portfolio, providing higher code density and DSP-like instructions while retaining the familiar MPLAB X toolchain and peripheral library. The PIC24EP64GP202T-I/SS belongs to the "GP" general-purpose sub-family with motor-control friendly peripherals absent and lower pin count, while the "MC" parts add high-speed PWM hardware. Key features are 1.1 Msps 10-bit or 500 ksps 12-bit configurable ADC with up to six analog inputs on 28-pin variants, three on-chip op-amps and four comparators, Peripheral Trigger Generator (PTG), and up to 21 I/O pins. The PIC24E core uses a modified Harvard architecture with a 16-bit instruction word and 24-bit instruction set extensions, supporting fractional arithmetic and DSP-style multiply instructions useful for motor control and digital filtering. Hardware-level DMA is not present on this 28-pin variant; data movement is handled by the CPU and peripherals. Typical applications include industrial sensor conditioning, low-cost motor control (BLDC, stepper) where the 70 MIPS headroom and CTMU enable capacitive touch sensing, portable instrumentation, and general-purpose 3.3 V embedded control. According to the Microchip datasheet, designers should observe the 3.0 V minimum supply and provide bulk decoupling near the VDDCORE pin to limit inrush during PLL start-up. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and engineering teams make informed second-source decisions.

RFQ Contact
PIC24EP64GP203-E/M5 - 60 MIPS 64KB MCU | Microchip
PIC24EP64GP203-E/M5

PIC24EP64GP203-E/M5 - 60 MIPS 64KB MCU | Microchip

The Microchip Technology PIC24EP64GP203-E/M5 is a 16-bit PIC24EP general-purpose microcontroller operating at 60 MIPS, with 64 KB of program Flash memory organized as 22K × 24 words, 8 KB of SRAM, and integrated analog peripherals. It is housed in a 36-lead 5 × 5 mm VFTLA surface-mount package with an exposed thermal pad. The device uses a 3.0 V to 3.6 V supply and the E temperature designation supports operation from -40°C to +85°C. A PIC24EP microcontroller is a 16-bit embedded controller positioned between general-purpose 8-bit devices and higher-performance digital signal controllers. The PIC24 architecture combines a high-performance CPU, Flash program memory, SRAM, timers, communication peripherals, and advanced analog functions in one integrated circuit. This broad integration makes the PIC24EP family useful for control systems that require more computation and peripheral flexibility than a basic microcontroller while retaining a compact embedded footprint. Key features include 60 MIPS performance, 64 KB of Flash, 8 KB of SRAM, three integrated operational amplifiers, four comparators, CTMU support, and a Peripheral Trigger Generator. The analog resources reduce the need for external amplifiers and signal-conditioning components in instrumentation, industrial control, and mixed-signal products. The 36-VFTLA package also provides an exposed pad that assists heat transfer when the device operates at sustained high clock rates. The PIC24E core provides an upgrade path from the PIC24F general-purpose family through improved performance, code density, and analog capability. According to the Microchip product page, the family targets high-end general-purpose applications with a high-speed core, improved ADC performance, CTMU, operational amplifiers, and PTG functionality. For this exact -E/M5 ordering code, the distributor-rated operating speed is 60 MIPS. Typical applications include industrial sensor acquisition, motor and power-system control, digital power conversion, instrumentation, automotive body electronics, and compact embedded control modules. The three internal operational amplifiers can amplify sensor signals, while the comparators support fast threshold decisions and protection functions. CTMU and the Peripheral Trigger Generator provide additional measurement and deterministic event-trigger capabilities for designs requiring more than basic GPIO control. Designers should treat the exposed pad as a thermal and electrical connection that must follow the package land-pattern requirements in the manufacturer datasheet. Place decoupling capacitors close to the supply pins, route sensitive analog inputs away from high-current switching nodes, and confirm the exposed-pad copper area and thermal-via strategy against the PCB assembly process. Firmware, peripheral configuration, and pin multiplexing must also be checked against the exact package pinout before layout release. This product page combines the exact ordering-code specifications with application guidance, pin and package constraints, verified sourcing information, and design checks for the PIC24EP64GP203-E/M5. It also distinguishes directly documented same-package options from unverified cross-brand substitutes so engineers can evaluate replacement choices without assuming software, timing, or peripheral compatibility.

RFQ Contact
PIC24EP64GP203-E/TL - 16-Bit MCU, 64KB Flash, 36-VTLA | Microchip
PIC24EP64GP203-E/TL

PIC24EP64GP203-E/TL - 16-Bit MCU, 64KB Flash, 36-VTLA | Microchip

The Microchip Technology PIC24EP64GP203-E/TL is a 16-bit PIC24EP general-purpose microcontroller with a 60 MIPS core, 64KB (22K x 24) of program Flash, and 8KB of RAM, housed in a 36-pin VTLA (5x5 mm) package with an exposed thermal pad. The device operates from 3.0V to 3.6V and is rated for the -40C to +125C extended automotive temperature range. Per the Microchip product page, the PIC24E core delivers high-speed 70 MIPS performance with excellent code density and superior ADC performance for mixed-signal embedded designs. A 16-bit microcontroller (MCU) is a programmable processor that fetches, decodes, and executes 16-bit-wide instructions, sitting in the broader taxonomy of microcontrollers -> microcontrollers and digital signal controllers -> embedded processors -> semiconductor devices. Compared with 8-bit MCUs, 16-bit devices offer higher arithmetic throughput, larger linear address spaces, and richer peripherals; compared with 32-bit MCUs they retain a smaller code footprint and lower cost at moderate performance levels. The PIC24EP family specifically adds enhanced ADC throughput, on-chip operational amplifiers, CTMU (Charge Time Measurement Unit) touch support, and a Peripheral Trigger Generator (PTG) for hardware-level event sequencing. Key features include 64KB Flash (22K x 24 instruction words), 8KB SRAM, hardware multipliers for DSP-style operations, multiple 16-bit timers, enhanced analog peripherals (ADC, op-amps, CTMU), and communication peripherals including UART, SPI, I2C, and ECAN. The 70 MIPS core execution rate delivers deterministic real-time performance for control loops, while the 16-bit instruction set keeps code density high relative to 32-bit alternatives. Architecturally, the PIC24EP64GP203-E/TL integrates the PIC24E core with on-chip op-amps for analog front-end conditioning, a CTMU for touch or capacitive sensing, and a Peripheral Trigger Generator (PTG) that sequences peripheral actions in hardware without CPU intervention. This reduces firmware overhead for high-speed control loops and event-driven signal acquisition in medical and industrial instrumentation. Typical applications include motor control (BLDC, stepper, and servo drives), industrial automation and sensor conditioning, automotive body and chassis ECUs, medical patient monitoring and diagnostic instrumentation, IoT edge nodes with on-chip op-amp signal chains, and consumer appliance control boards. The wide operating temperature range and integrated analog make it well suited for harsh-environment designs. Design consideration: at 60 MIPS execution the device draws noticeable active current, so quiescent-current-critical designs should enable Sleep/Idle modes and gate unused peripherals. Place the decoupling network (100nF plus bulk) within 5 mm of the VDD pins to keep the on-chip op-amps and ADC free of switching noise. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design guidance not found on a single manufacturer or distributor page.

RFQ Contact
PIC24EP64GP203-I/M5 - 16-bit 70 MIPS MCU 64KB Flash 36-VTLA | Microchip
PIC24EP64GP203-I/M5

PIC24EP64GP203-I/M5 - 16-bit 70 MIPS MCU 64KB Flash 36-VTLA | Microchip

The Microchip Technology PIC24EP64GP203-I/M5 is a high-performance 16-bit microcontroller from the PIC24E general-purpose family, featuring the high-speed 70 MIPS core, 64 KB of Flash program memory and 8 KB of data RAM. The part is housed in a compact 36-pin VTLA (5x5 mm) package, runs at an operating voltage of 3.0V to 3.6V, and supports an industrial temperature range of -40C to +85C as indicated by the -I suffix. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. The PIC24E family sits in the dsPIC/PIC24 16-bit DSC architecture family within Microchip's broader 8/16/32-bit MCU portfolio. PIC24E devices add high-performance peripherals such as high-speed PWM, operational amplifiers, comparators, CTMU (Charge Time Measurement Unit), and the Peripheral Trigger Generator (PTG) for advanced timing and signal-conditioning tasks. The 70 MIPS core delivers excellent performance and code density for high-end general-purpose embedded applications. Key features include 64 KB (22K x 24) of Flash with self-programmability, 8 KB of RAM, a 16-bit CPU with hardware multiply/divide, three on-chip op-amps, four comparators, a 12-bit ADC with up to 16 channels (depending on variant), CTMU for touch and time measurement, and the Peripheral Trigger Generator. The 36-VTLA package has only 5x5 mm board area, ideal for space-constrained designs. Industrial-grade -40C to +85C operation, plus rich connectivity including I2C, SPI, UART, and high-speed PWM make it suitable for motor control and digital power conversion. Typical applications include digital power conversion (PFC, LLC, full-bridge converters), high-performance motor control (sensorless FOC, BLDC/PMSM drives), advanced sensor conditioning (using the on-chip op-amps, CTMU, and comparators), industrial control and automation, and LED lighting controllers. The CTMU enables cost-effective capacitive touch interfaces, and the PTG allows autonomous peripheral sequencing without CPU intervention for deterministic timing in safety-relevant loops. When designing with this part, follow Microchip's recommended decoupling scheme: a 100 nF low-ESR ceramic placed within 2 mm of each power pair, plus a bulk 4.7-10 uF tantalum or ceramic on the main supply. Use Microchip's MPLAB X IDE and MPLAB XC16 compiler for firmware development; pick ICD 3 or PICkit 4 for in-circuit programming and debugging.

RFQ Contact
PIC24EP64GP203-I/TL - 16-bit 70MIPS MCU 64KB Flash 36-VTLA | Microchip
PIC24EP64GP203-I/TL

PIC24EP64GP203-I/TL - 16-bit 70MIPS MCU 64KB Flash 36-VTLA | Microchip

The Microchip Technology PIC24EP64GP203-I/TL is a 16-bit microcontroller from the PIC® 24EP general-purpose family, delivering 70 MIPS core performance with 64 KB of Flash program memory and 4 KB of RAM in a 36-pin VTLA (5x5 mm) package with exposed pad. It operates from a 3.0 V to 3.6 V single supply and integrates advanced analog features including operational amplifiers, a Charge Time Measurement Unit (CTMU), a 10-bit ADC, and a Peripheral Trigger Generator (PTG) for hardware-based timing and sequencing without CPU intervention. A 16-bit PIC microcontroller is a member of the microcontroller (MCU) product category — specifically a Harvard-architecture MCU with a modified instruction set optimized for deterministic real-time control. In the system hierarchy, the PIC24EP sits between 8-bit PIC MCUs (PIC16/PIC18) and 32-bit ARM Cortex-M parts, offering significantly higher code density and DSP capability while preserving deterministic interrupt latency. It belongs to the broader class of digital signal controllers (DSCs) and is widely used where 8-bit MCUs are too slow but 32-bit Cortex-M parts are over-specified for cost-sensitive designs. Key features include a 70 MIPS (max) CPU core, dual 10-bit/12-bit ADC options, internal temperature sensor, up to 25 mA source/sink on I/O, JTAG/ICSP debug, and a Peripheral Trigger Generator that coordinates peripherals autonomously. The PTG is a hardware state machine that sequences ADC sampling, PWM updates, and CTMU timing operations with zero software overhead, enabling deterministic sub-microsecond response for power-conversion and motor-control loops. Architecturally, the PIC24EP uses a 16-bit modified Harvard core with separate program and data buses. Flash memory is accessed through a 24-bit-wide instruction path supporting 22K × 24 program word addressing, yielding the 64 KB program memory. A 4 KB RAM area is dual-ported to the CPU and DMA engine; a single-cycle MAC instruction enables DSP-class digital filtering with deterministic timing for power conversion loops. Typical applications include industrial motor control (BLDC/PMSM sensorless FOC), digital power conversion (digitally controlled SMPS with PTG-driven ADC/PWM synchronization), LED lighting controllers, battery management systems (BMS), USB device peripherals with the on-chip USB 2.0 Full-Speed transceiver, and medical instrumentation such as portable patient monitors. When designing with this MCU, note that the VTLA-36 (5 × 5 mm) package requires careful PCB layout to maximize the exposed-pad ground connection for thermal dissipation (continuous GPIO sink current up to 25 mA creates localized heating under high-load conditions). Use the Peripheral Trigger Generator to offload real-time sequencing from the CPU, and ensure VDD decoupling includes 100 nF ceramic capacitors placed within 5 mm of each power pin plus a bulk 4.7 µF tantalum or polymer cap on VDD. This page synthesizes distributor stock, drop-in replacements within the same VTLA-36 footprint, and practical design notes (PTG use cases, ADC calibration, decoupling topology) that go beyond what the manufacturer datasheet provides — useful for procurement engineers and embedded firmware developers evaluating PIC24EP family selections.

RFQ Contact
PIC24EP64GP203T-I/TL - 16-bit MCU 64KB Flash 36VTLA | Microchip
PIC24EP64GP203T-I/TL

PIC24EP64GP203T-I/TL - 16-bit MCU 64KB Flash 36VTLA | Microchip

The Microchip PIC24EP64GP203T-I/TL is a 16-bit microcontroller from the PIC24EP general-purpose MCU family, featuring a 70 MIPS high-performance core and 64KB of Flash program storage with 8KB of RAM. It is housed in a 36-pin VTLA (Very Thin Leadless Array) surface-mount package with an exposed thermal pad, making it suitable for compact, thermally-constrained designs in industrial and consumer applications. What is a PIC24EP general-purpose MCU? The PIC24E/PIC24EP family is Microchip's 16-bit DSC/MCU line that sits between the 8-bit PIC16/PIC18 families and the 32-bit PIC32MX families in the broader Microchip microcontroller hierarchy (8-bit MCU -> 16-bit MCU -> 32-bit MCU -> microcontroller -> embedded controller). PIC24EP devices integrate signal-chain analog peripherals such as operational amplifiers, comparators, and CTMU (Charge Time Measurement Unit) directly on-chip, which historically required external components on simpler MCUs. This integration makes PIC24EP parts well-suited for closed-loop control and mixed-signal sensing tasks. Key differentiating specifications include: 70 MIPS core performance from a 60 MHz (max) CPU with DSP instructions; up to three on-chip operational amplifiers; up to four high-speed comparators with a 10-bit Peripheral Trigger Generator (PTG); and the CTMU peripheral for capacitive touch and time-of-flight measurement. The on-chip op amps and comparators eliminate the need for external analog front-end ICs in many motor-control and power-conversion designs, reducing BOM count and PCB complexity. Architecturally, the PIC24EP64GP203T-I/TL uses a modified Harvard architecture with separate program Flash and data RAM buses, enabling simultaneous instruction fetch and data access. The device operates from a 3.0V to 3.6V single supply, with 5V-tolerant digital I/O for mixed-voltage interfaces, and integrates a 10/12-bit ADC with up to 1.1 Msps conversion rate for high-speed analog acquisition. Typical applications include industrial motor control (BLDC, PMSM, and stepper drives), digital power conversion (DC-DC converters and PFC stages), capacitive touch sensing human-machine interfaces (HMIs), LED lighting drivers, and general-purpose embedded control in appliances and consumer products. The exposed thermal pad of the VTLA-36 package supports sustained DSP compute loads without thermal throttling. When designing with this device, ensure the VTLA-36 PCB footprint includes adequate thermal vias under the exposed pad to keep junction temperature within the -40C to +85C industrial operating range. Programming and debugging are supported via the standard 4-wire ICSP interface, and the MPLAB X IDE with the MPLAB XC16/Code Compiler provides a complete firmware development toolchain. This page synthesizes distributor pricing, drop-in same-package alternatives, application context, and design guidance into a single engineering reference not available on the manufacturer datasheet.

RFQ Contact
PIC24EP64GP204-E/ML - 16-Bit 60 MIPS 64KB Flash MCU | Microchip
PIC24EP64GP204-E/ML

PIC24EP64GP204-E/ML - 16-Bit 60 MIPS 64KB Flash MCU | Microchip

The Microchip Technology PIC24EP64GP204-E/ML is a 16-bit PIC24EP general-purpose microcontroller featuring a high-performance 60 MIPS CPU core, 64 KB of Flash program memory, and 8 KB of RAM, housed in a 44-pin QFN (ML) 8x8 mm package. It operates from a 3.0 V to 3.6 V supply, integrates an enhanced ADC, op amps, CTMU, and Peripheral Trigger Generator (PTG), and exposes 35 general-purpose I/O pins across the 44-QFN land pattern. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and a configurable set of peripherals such as ADC, timers, communication interfaces (UART, SPI, I2C), and GPIO into one package. Within the broader system hierarchy, the PIC24EP64GP204 belongs to the 16-bit microcontroller class -> DSP-capable MCU -> embedded controller -> semiconductor IC, and within Microchip's portfolio to the PIC24E "high-performance, general-purpose" family. The 16-bit data path plus 70 MHz internal oscillator allows deterministic real-time control loops that 8-bit MCUs cannot economically deliver. Key differentiating features include the dsPIC33/PIC24E enhanced Harvard architecture with hardware multiply/divide, a 10-bit 1.1 Msps ADC with up to 32 channels, four on-chip operational amplifiers for analog front-end conditioning, the CTMU for capacitive-touch and time-based measurement, the Peripheral Trigger Generator (PTG) for offloading CPU-paced event sequencing, and a parallel master port for external bus expansion. The 44-QFN package exposes a generous 35 GPIO budget despite the small 8x8 mm footprint, enabling space-constrained industrial boards. From an architecture perspective, the device uses a 2-cycle hardware multiplier and zero-overhead loop control, giving effective C-code density close to 70 MIPS throughput. The PTG and CTMU in particular let firmware replace external analog/digital timing chips - a board-level cost and BOM reduction. Industrial-grade -40C to +125C operation makes it usable in motor control, lighting, and sensor-hub designs that 8-bit PIC16/PIC18 parts cannot address. Typical applications include industrial motor control (BLDC and PMSM), digital lighting and LED drivers, sensor-reading and pose-location hub designs, capacitive-touch human-machine interfaces, and consumer appliances. The combination of on-chip op amps and CTMU is especially attractive in products that must minimize external analog components while maintaining analog accuracy. When laying out the PCB, allocate at least one solid ground plane beneath the exposed thermal pad of the 44-QFN and stitch it to the system ground with a 4- to 6-via array - thermal dissipation and EMI performance both depend on the EP being well-bonded. Always program the configuration bits for the correct oscillator mode before debugging, or the device will appear dead. This page synthesizes XAIPART distributor comparison data, same-family PIC24EP drop-in alternatives, and practical QFN-layout design notes not found in the standalone manufacturer datasheet.

RFQ Contact
PIC24EP64GP204-E/MV - 16-Bit 60 MIPS MCU | Microchip Technology
PIC24EP64GP204-E/MV

PIC24EP64GP204-E/MV - 16-Bit 60 MIPS MCU | Microchip Technology

The Microchip Technology PIC24EP64GP204-E/MV is a 16-bit PIC24E general-purpose microcontroller with 64 KB of Flash memory, 8 KB of data RAM, three internal operational amplifiers, and a Peripheral Trigger Generator. It is offered in a 48-UQFN package measuring 6 mm by 6 mm and is identified as an automotive-grade, AEC-Q100 device. A microcontroller is a programmable semiconductor that integrates a CPU, memory, and peripherals into one component. The PIC24E family belongs to the broader embedded-controller hierarchy: general-purpose MCU, embedded processor, microcontroller, and semiconductor. These devices combine deterministic peripheral control with analog and communication functions, allowing a compact system to sense, process, and transmit data without requiring several separate analog and interface chips. The PIC24EP64GP204-E/MV combines a 16-bit architecture with up to 70 MIPS according to the Microchip family description, while the exact automotive ordering code is listed by distributors at 60 MIPS. Its 64 KB Flash supports embedded firmware, and its 8 KB RAM supports working data and buffers. Three integrated operational amplifiers reduce the need for external analog amplifiers in sensing and signal-conditioning circuits. The Peripheral Trigger Generator provides hardware-assisted event triggering for deterministic measurements and control sequences. Operation from 3.0 V to 3.6 V supports common 3.3 V embedded systems. The family description identifies an operating range extending from -40 °C upward, and exact suffix limits are identified through the ordering information. Integrated communication and timing resources include I2C, SPI, UART, IrDA, LIN, DMA, timers, and a PWM architecture, allowing the MCU to serve as the central controller for connected industrial, automotive, and instrumentation products. Typical applications include automotive body and environment modules, industrial sensor controllers, condition-monitoring equipment, motor-control interfaces, and compact communications gateways. The three internal operational amplifiers are particularly useful when the design needs local gain, buffering, or current-voltage conversion close to the MCU. The Peripheral Trigger Generator can synchronize ADC measurements and output events, reducing the timing burden on firmware in precision and safety-related control systems. PCB design should preserve short analog paths between sensor inputs and the internal amplifiers, provide clean power and ground planes, and route high-current outputs away from sensitive analog nodes. Designers should also verify the exposed-pad connection and decoupling requirements in the Microchip pin description before layout release. This page combines device specifications, same-footprint alternatives, application guidance, and practical design considerations to support component selection and PCB implementation.

RFQ Contact
PIC24EP64GP204-E/PT - 16-bit 70 MIPS MCU, 64KB Flash, 44-TQFP | Microchip
PIC24EP64GP204-E/PT

PIC24EP64GP204-E/PT - 16-bit 70 MIPS MCU, 64KB Flash, 44-TQFP | Microchip

The Microchip Technology PIC24EP64GP204-E/PT is a high-performance 16-bit microcontroller from the PIC24EP family, delivering up to 70 MIPS throughput from a 60 MHz CPU core, packaged in a 44-pin TQFP (10x10 mm). It integrates 64 KB of flash program memory (22K x 24 words), 8 KB of SRAM, and a rich analog/digital peripheral set including three on-chip operational amplifiers, four comparators, a Charge Time Measurement Unit (CTMU), and a Peripheral Trigger Generator (PTG) for hardware-level state machine sequencing. A 16-bit MCU is a microcontroller whose data path, registers, and ALU are 16 bits wide. Compared with 8-bit MCUs (e.g., PIC16, 8051), a 16-bit core performs arithmetic on 16-bit operands in a single instruction and can address larger memory spaces directly, while still consuming less power and offering simpler deterministic interrupt handling than 32-bit Cortex-M cores. The PIC24EP family sits in the middle of Microchip's portfolio between the 8-bit PIC18 and the 32-bit PIC32MX/MZ lines, targeting high-end general-purpose embedded designs that need strong DSP-like performance and large peripheral integration on a single die. Key features include a 10/12-bit ADC with up to 1.1 Msps conversion, two UART/SPI/I2C-configurable serial interfaces, three 16-bit timers, five 16-bit capture/compare/PWM channels, and an extended -40C to +125C operating range (the trailing -E in the part number denotes the extended temperature grade). The 70 MIPS performance, combined with a 16-bit modified Harvard bus and DSP engine for single-cycle 16x16 MAC operations, enables digital signal conditioning, motor control loops, and audio processing in software without an external DSP. The architecture combines a 16-bit modified Harvard CPU with tightly-coupled analog peripherals, including three operational amplifiers that can be configured as unity-gain buffers or as gain stages driving the on-chip ADC. The PTG (Peripheral Trigger Generator) is a hardware sequencer that chains ADC, PWM, and timer events at hardware speed, offloading work from the CPU and enabling deterministic sub-microsecond response times critical for power-conversion and motor-control loops. Typical applications include industrial motor control, switch-mode power supplies with digital compensation, sensor signal conditioning, LED lighting controllers, and consumer devices requiring 16-bit DSP performance without the cost of a 32-bit MCU. The extended temperature grade makes the part suitable for under-hood automotive subsystems, industrial automation, and outdoor equipment. When designing with this MCU, reserve adequate PCB area for the 44-pin TQFP exposed thermal pad layout, and confirm that the ADC reference voltage source can drive the 3 internal op amps plus ADC sample capacitance in worst-case back-to-back burst conversions. For new designs, consider the pin-compatible PIC24EP512GP204-E/PTI (512 KB flash) as a drop-in upgrade path for code growth. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact