Amplifier ICs
بەرهەمەکان (3,200+)
TS942BID - Dual Rail-to-Rail Micropower Op Amp | STMicroelectronics
The STMicroelectronics TS942BID is a dual-circuit, rail-to-rail output micropower operational amplifier packaged in an 8-pin SOIC. Its 2.5 V to 10 V supply range, 60 dB gain-bandwidth product, 5 mA output current capability, and approximately 1.2 µA supply current per channel suit low-voltage analog systems that require low quiescent power and input/output operation near the supply rails. The TS942BID is intended for instrumentation, signal-conditioning, and general-purpose analog applications. An operational amplifier is a high-gain analog building block that compares two input voltages and amplifies their difference. Within the broader semiconductor hierarchy, the TS942BID belongs to the operational-amplifier category, then analog amplifier ICs, and finally integrated circuits. Rail-to-rail output capability permits the output to approach the positive and negative supply limits under suitable load and output-voltage conditions, making the device useful in low-voltage sensor, portable-instrumentation, and battery-powered signal chains. The device uses a 2.5 V minimum operating supply and supports supplies up to 10 V. Its typical gain-bandwidth product is 60 dB, while its typical output current capability is 5 mA per channel. The low-power operating characteristics are reflected in a quoted supply current of 1.2 µA per channel, and the offset-related listing identifies approximately 0.00015 µA, or 150 nA, of input bias current. These characteristics make the TS942BID appropriate for applications in which amplifier power can dominate the total system budget. The TS942BID contains two amplifier channels in one compact 8-SO package. Its standard general-purpose classification and rail-to-rail architecture make it suitable for signal conditioning, low-level amplification, and buffer stages. Designers should still account for the finite gain-bandwidth product when operating at higher closed-loop gains, because bandwidth reduces as the noise gain rises. Input common-mode range, output swing, offset voltage, noise density, and slew rate should be confirmed from the manufacturer datasheet before precision or high-speed signal-chain use. Typical application areas include portable sensor interfaces, low-power instrumentation, battery-operated measurement systems, and general analog signal conditioning. In a sensor interface, the TS942BID can amplify a low-level sensor output while keeping channel current consumption small. In an instrumentation block, its dual-channel configuration can reduce component count when two related signals must be conditioned. As a buffer, it can isolate a higher-impedance source from a downstream analog stage while maintaining a compact eight-pin footprint. Layout and stability remain important in micropower designs. Place input and feedback components close to their associated pins, keep sensitive input traces away from switching nodes, and avoid long high-impedance traces that can increase leakage and noise pickup. Select passive feedback values that account for the amplifier’s gain-bandwidth limit, and verify operation across the full 2.5 V to 10 V supply range. The manufacturer datasheet should be used for the final pin assignment, typical characteristics, absolute maximum ratings, and application-circuit details. This product summary combines the manufacturer’s device description with practical guidance for package reuse, analog layout, low-power selection, and replacement evaluation. It also distinguishes verified drop-in interchangeability from merely similar amplifier functions, helping engineers avoid PCB rework and unexpected bias, bandwidth, or supply-voltage differences.
TS942BIN - Dual Micropower Rail-to-Rail Op Amp | ST
The STMicroelectronics TS942BIN is a dual, general-purpose operational amplifier with rail-to-rail output, a 10 kHz gain-bandwidth product, and a typical supply current of 1.2 µA per amplifier. The device operates from 2.5 V to 10 V across a -40 °C to +85 °C temperature range and is supplied in an 8-pin PDIP package. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to compare two input voltages. The TS94x series belongs to the low-power operational-amplifier hierarchy, combining rail-to-rail output capability with low bias current. This makes it useful in battery-powered instrumentation, sensor interfaces, buffer stages, and other systems that require low supply current without bipolar-input transistor limitations. Key characteristics include two amplifier circuits, rail-to-rail output operation, a 10 kHz gain-bandwidth product, a slew rate of 0.0045 V/µs, input offset voltage of up to 2 mV, and input bias current as low as 1 pA. The low 1.2 µA supply current is particularly valuable in portable equipment, while the 2.5 V minimum supply voltage supports low-energy system rails. The micropower architecture favors low-frequency signal conditioning rather than high-speed amplification. Its 10 kHz gain-bandwidth product limits usable closed-loop bandwidth according to the selected feedback network, while the 0.0045 V/µs slew rate governs large-signal response. Rail-to-rail output improves output swing on low-voltage supplies, although input common-mode range, output loading, and stability still require careful circuit-level evaluation. Typical uses include buffering sensor outputs, amplifying low-level signals in battery-operated instruments, driving analog measurement inputs, and providing gain stages in portable monitoring equipment. The dual configuration can implement two independent amplifiers in instrumentation, filtering, or signal-conditioning circuits while reducing package count. Layout should keep input, feedback, and decoupling connections short, and should avoid routing high-impedance input traces beside switching or high-current paths. Place the supply bypass capacitor close to the device, observe common-mode and output-swing limits, and verify stability with the intended source and load impedances. Because the TS942BIN is obsolete, maintain a controlled last-time-buy plan for maintenance and repair production.
TS942ID - Dual Micropower Op Amp | STMicroelectronics
The STMicroelectronics TS942ID is a dual, rail-to-rail, micropower operational amplifier with two amplifier channels, a 10 kHz gain-bandwidth product, and a 0.0045 V/us slew rate. It operates from a single supply of 2.5 V to 10 V and is packaged in an 8-pin SOIC. Each channel is designed for low-power signal conditioning and general-purpose analog measurements. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, or compare small voltage signals. In the signal-chain hierarchy, the TS942ID belongs to the operational-amplifier family within analog amplifier ICs and power-management systems. Its micropower operating current and rail-to-rail output behavior make it suitable for portable instrumentation, sensor interfaces, and low-voltage analog equipment. The TS942ID provides a supply-current consumption of 1.2 uA and an ultra-low input bias current of 1 pA. These characteristics reduce loading on high-impedance sensors and conserve energy in battery-operated systems. Its output swing is rail-to-rail, while single-supply operation extends to 10 V. The device also includes CMOS inputs, 2 kV ESD protection, and latch-up immunity for improved handling robustness. With a gain-bandwidth product of 10 kHz and a slew rate of 0.0045 V/us, the TS942ID favors precision and low-power operation over wideband performance. The 10 kHz bandwidth is suitable for slow sensor signals, ECG-scale physiological waveforms, precision current measurement, and low-frequency filtering. CMOS input stages support very low bias current, making the amplifier appropriate for high-source-impedance transducers where input loading must remain minimal. Typical uses include portable biomedical instrumentation, low-power sensor conditioning, battery-powered data acquisition, industrial process monitoring, and general-purpose buffering. Two independent channels can process complementary signals or provide simultaneous amplification. Because each channel can also be configured as a comparator-style element with suitable feedback, designers can use the same device for basic threshold and level-detection functions. The principal design consideration is bandwidth. The 10 kHz gain-bandwidth product limits high-gain signal bandwidth, so applications requiring faster edges or wider closed-loop bandwidth should account for the amplifier's finite slew rate. Input and output stability must also be evaluated with the source impedance, load capacitance, supply voltage, and selected feedback network.
TS942IN - Dual 1.2 µA Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS942IN is a dual, rail-to-rail output micropower operational amplifier designed for 2.5 V to 10 V single-supply operation. The device provides two amplifier circuits in an 8-pin Mini DIP package, with a typical micropower consumption of 1.2 µA. Its CMOS inputs feature ultra-low input bias current, while the rail-to-rail output stage supports low-voltage signal conditioning where the output must approach the supply rails. The specified operating temperature range is -40 °C to +85 °C. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TS94x family belongs to the operational amplifier, analog amplifier, and linear integrated-circuit hierarchy. Operational amplifiers are widely used as voltage followers, buffers, comparators, transimpedance amplifiers, and active analog filters. The TS942IN combines low supply current, single-rail operation, CMOS input characteristics, and rail-to-rail output swing in one low-power analog building block. The 1.2 µA micropower characteristic makes the TS942IN particularly suitable for battery-operated sensors, portable instruments, and low-energy monitoring systems. Its 2.5 V minimum supply voltage allows operation from a single low-voltage cell or regulated rail. Rail-to-rail output swing is valuable in low-voltage systems because it increases usable output range. The low input bias current reduces errors in source impedance-sensitive circuits and minimizes disturbance to high-impedance sensors. The TS942IN uses CMOS input circuitry and is intended for general-purpose low-power analog signal processing. Each amplifier can support common inverting, non-inverting, and voltage-following configurations. Because the output approaches the supply rails, careful load and feedback design remains necessary when the output must achieve accurate levels near either rail. Input common-mode range, output swing, gain-bandwidth behavior, and stability conditions should be taken directly from the manufacturer datasheet when selecting feedback networks. Typical uses include low-frequency sensor conditioning, portable instrumentation, medical monitoring, industrial threshold detection, and energy-efficient data acquisition. In battery-powered equipment, the low supply current reduces the continuous load imposed by the amplifier. In precision measurements, the low input bias current helps preserve the signal from sensors with high source impedance. The device is also useful when one package must provide two matched functional amplifier channels. Designers should verify the permitted input and output ranges at the selected supply voltage, account for input and output capacitance in feedback layouts, and avoid driving a load that exceeds the amplifier's recommended capability. A stable bypass capacitor close to the supply pins and short, direct routing for high-impedance inputs help preserve low-noise and low-power performance. This product page combines the manufacturer specifications, package information, sourcing guidance, functional alternatives, and practical circuit-level considerations for engineers evaluating the TS942IN. It is intended to accelerate part selection while keeping the critical design tradeoffs explicit: low power and low bias current versus the bandwidth, noise, and load capability required by a particular signal chain.
TS942IPT - 10kHz Dual RRO Op Amp | STMicroelectronics
The STMicroelectronics TS942IPT is a dual-circuit, rail-to-rail operational amplifier with a 10 kHz gain-bandwidth product, supplied in an 8-pin TSSOP package. The device combines rail-to-rail input and output capability with low supply current and is intended for compact, low-power analog signal-processing systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to establish gain and bandwidth. A rail-to-rail input stage accepts signals close to the positive and negative supply rails, while a rail-to-rail output stage can approach those limits under suitable load conditions. The TS942IPT therefore belongs to the rail-to-rail operational-amplifier family within the broader amplifier and analog IC hierarchy. Key characteristics include two amplifier circuits in one package, 10 kHz gain-bandwidth product, rail-to-rail operation, and approximately 1.2 µA supply current per channel. Its listed typical output current is 5 mA. These characteristics make it suitable for low-power sensor interfaces, portable instrumentation, and signal-conditioning circuits where device count, board area, and energy use are important constraints. The TS942IPT uses an 8-TSSOP package measuring approximately 0.173 inch, or 4.40 mm, in width. Tape-and-reel packaging supports high-volume automated assembly. The manufacturer specifies an operating-temperature range of -40 °C to +85 °C. As a general-purpose dual amplifier, it can reduce component count in designs that need two nearly identical signal-conditioning channels. Typical uses include low-level sensor signal conditioning, battery-powered measurement modules, industrial control interfaces, portable medical instruments, and low-voltage audio or communication front ends. Two independent amplifier sections can handle separate channels in a dual-axis sensor, differential receiver, filter, or gain stage, provided each channel's stability, common-mode range, and output-drive requirements are satisfied. Designers should verify input and output headroom, capacitive-load behavior, noise performance, and output-current demand against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined common-mode voltage. The low 10 kHz bandwidth favors precision and low-power operation rather than high-speed signal handling. This page combines the exact TS942IPT package and operating characteristics with application guidance, same-family drop-in alternatives, a parameter comparison, and practical layout considerations. It helps engineers evaluate the amplifier's role in low-power analog designs without confusing it with higher-bandwidth or higher-current rail-to-rail amplifiers.
TS944AID - Quad Rail-to-Rail Micropower Op Amp | STMicroelectronics
STMicroelectronics TS944AID is a four-circuit, rail-to-rail output operational amplifier designed for low-voltage and low-power signal-conditioning systems. The device operates from 2.5 V to 10 V, supports an operating temperature range of -40°C to +85°C, and is packaged in a 14-pin SOIC. Each amplifier consumes approximately 1.2 µA of supply current, making the TS944AID suitable for battery-powered instrumentation, portable measurement systems, and industrial sensor interfaces. An operational amplifier is a high-gain analog building block used to amplify, buffer, filter, and compare small voltage signals. The TS944AID belongs to the rail-to-rail output operational-amplifier family, combining four independent amplifier channels with a common supply in one compact 14-pin package. Rail-to-rail output operation allows the output voltage to approach the supply rails more closely than a conventional fixed-headroom amplifier, improving usable signal range in low-voltage systems. The four-channel arrangement reduces package count and simplifies routing in designs requiring several similar amplifier stages. A 2.5 V minimum supply supports low-energy systems, while the 10 V maximum supply provides flexibility for conventional industrial signal ranges. The approximately 1.2 µA supply current per channel is particularly valuable when every microwatt affects battery life. The -40°C to +85°C operating range supports industrial equipment and consumer products requiring operation beyond room temperature. STMicroelectronics describes the TS944 series as micropower, rail-to-rail output operational amplifiers. Its four-channel architecture is useful for sensor conditioning, current-loop receivers, filtering, and low-level signal buffering. Because the TS944AID combines four amplifiers in one package, matching channels can simplify calibration, reduce board area, and keep sensitive analog paths physically close. Decoupling and stable-reference techniques remain important when the amplifier operates beside switching circuitry or long sensor cables. Typical uses include industrial pressure and temperature sensors, low-power condition-monitoring equipment, portable measurement instruments, analog interface boards, and general-purpose signal buffers. In a sensor front end, two channels can amplify or level-shift sensor outputs while the remaining channels support filtering, threshold detection, or output buffering. Its low supply current is advantageous when the complete system must operate from a small energy source rather than a laboratory supply. For PCB design, place the supply bypass capacitor close to the device and route high-impedance input and feedback traces away from switching nodes and fast digital signals. Confirm output swing, input common-mode range, stability, and capacitive-load limits against the manufacturer datasheet for the actual supply voltage and load. Verify the exact pin orientation and channel assignments before assembly because the SOIC-14 outline alone does not identify the functional pins. This product page consolidates the device identity, operating envelope, package information, replacement considerations, and application-oriented design guidance. It also distinguishes confirmed family information from parameters that require direct consultation of the manufacturer datasheet before precision analog design or PCB release.
TS944AIN - Quad Micropower Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS944AIN is a quad general-purpose operational amplifier with four independent rail-to-rail output channels in a 14-DIP through-hole package. It operates from low supply voltages and provides a typical supply current of 1.2 uA per channel, a 10 kHz gain-bandwidth product, and a 0.0045 V/us slew rate. An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify small voltage differences. A rail-to-rail output stage can approach the positive and negative supply rails, improving output-voltage range in low-voltage systems. The TS944AIN belongs to the operational-amplifier hierarchy within analog and signal-chain semiconductors, combining four amplifier channels, micropower consumption, and through-hole construction in one package. The four-channel architecture reduces the number of amplifiers needed for multi-signal conditioning. Each channel offers a typical 10 kHz gain-bandwidth product and 0.0045 V/us slew rate, making the device appropriate for low-frequency buffering, sensor amplification, and general-purpose signal conditioning. Typical input bias current is 1 pA, while typical input offset voltage is 5 mV. Performance is optimized for low-power rather than high-speed operation. The 10 kHz gain-bandwidth product favors stable operation near unity gain and limits bandwidth in precision measurement stages. The 0.0045 V/us slew rate also means the amplifier requires time to respond to larger output transitions. Its 1.2 uA typical supply current per channel reduces the power budget in portable and always-on equipment. Typical uses include low-frequency sensor interfaces, battery-powered instrumentation, audio signal conditioning, industrial control inputs, and four-channel acquisition systems. The 14-DIP format is useful for through-hole prototypes, educational circuits, repair work, and industrial assemblies where a socketed or manually inserted package is preferred. Designers should verify the complete electrical limits, input common-mode range, output swing, supply range, and stability requirements in the STMicroelectronics datasheet before finalizing the circuit. Decoupling capacitors, input bias-current return paths, output loading, and resistor values remain application-dependent and should be selected from the device's recommended operating conditions.
TS944BID - Quad R-R Op Amp, 14-SO | STMicroelectronics
The STMicroelectronics TS944BID is a four-circuit, rail-to-rail micropower operational amplifier in a 14-pin SO package. It combines four general-purpose amplifier channels with output swing that reaches the supply rails, while a related TS944BIDT ordering code is identified as a 10 kHz, 14-SO device. The 14-SO outline gives the TS944BID a compact surface-mount footprint suitable for multi-channel analog signal conditioning, instrumentation, sensor interfaces, and low-power embedded systems. An operational amplifier, or op amp, is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. A rail-to-rail output amplifier can swing its output close to the positive and negative supply limits, increasing usable output range in single-supply systems. The TS944BID therefore belongs to the operational-amplifier hierarchy within analog ICs and general-purpose amplifier ICs, where four matched channels can reduce package count in designs requiring several signal paths. The principal feature of the TS944BID is its four-channel integration. Each channel provides rail-to-rail output capability, making the device applicable to buffering, gain stages, voltage comparison, and low-frequency analog conditioning. The related TS944BIDT listing identifies the family at 10 kHz gain-bandwidth product, which positions it for low-frequency signal paths rather than high-speed data acquisition. Rail-to-rail operation can also simplify interfacing with ADC inputs when the signal source occupies a large portion of the available supply range. TS944BID combines four amplifiers in one 14-SO package, reducing the number of discrete amplifier packages required for quad-channel analog circuits. Its micropower classification emphasizes low-power operation, although exact supply current, input offset voltage, noise density, and common-mode limits must be checked in the manufacturer datasheet before a production design is released. Component designers should also confirm the exact ordering-code temperature range and shipping format when placing a regulated bill of materials. Typical uses include current sensing around an instrumentation amplifier, sensor signal conditioning in industrial systems, buffered ADC inputs, low-level audio preamplification, and portable measurement equipment. Four channels are particularly useful when transducers, filters, or data-conversion inputs require consistent amplifier topology. The 14-SO package also allows the device to be placed alongside a microcontroller, analog-to-digital converter, or digital interface IC on a compact circuit board. Designers should verify the input common-mode range, output load capability, stability with the selected feedback network, and decoupling requirements against the STMicroelectronics datasheet. Place the bypass capacitor close to the supply pins and use the pin-description table when assigning PCB nets. Because TS944BID is marked obsolete, new production designs should confirm lifecycle status and consider an actively supported amplifier for new releases. This product record combines package and functional identification with lifecycle, compliance, sourcing, replacement, and application guidance. It also distinguishes the exact TS944BID ordering code from TS944BIDT and explains where engineers should verify electrical limits, mechanical details, and approved alternatives before committing a design to production.
TS944BIN - Quad Rail-to-Rail Low-Power Op Amp | STMicroelectronics
The STMicroelectronics TS944BIN is a four-circuit, rail-to-rail operational amplifier designed for low-voltage, low-power analog signal conditioning. It operates from 2.5 V to 10 V across a temperature range of -40°C to +85°C, and is packaged in a 14-pin DIP. Its quad configuration provides four amplifiers in one package, reducing board area and simplifying multi-channel designs. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify voltage differences between its input terminals. The TS944 belongs to the operational-amplifier hierarchy, combining rail-to-rail input and output capability with micropower operation. Rail-to-rail behavior is particularly useful when signals must be processed across most or all of the device supply range. The TS94x family combines four amplifiers with a supply current of 1.2 µA per amplifier and a maximum input offset voltage of 5000 µV. Its input bias current is specified at 0.15 nA, making it suitable for high-impedance sensor interfaces when bias-current loading must be controlled. Rail-to-rail output voltage swing supports portable, industrial-control, and low-voltage measurement systems. The TS944 is intended for general-purpose analog applications rather than high-speed signal processing. Its four independent channels can be configured as noninverting amplifiers, inverting amplifiers, voltage followers, comparators, or transimpedance amplifiers. The common quad package also simplifies power distribution and reduces the number of separate analog packages required on a board. Typical uses include battery-powered instrumentation, current-loop receivers, sensor-conditioning circuits, low-voltage audio paths, and general industrial control systems. Four matched functional channels can process several related signals in one assembly, while the low 1.2 µA supply current helps limit power consumption in portable and energy-limited equipment. Designers should verify input and output common-mode limits, output-current capability, stability with the selected load capacitance, and noise performance for the intended signal bandwidth. Input and output bypassing should follow the manufacturer's recommended application circuit, and unused amplifier channels should be configured conservatively rather than left open. This page combines device specifications, practical application guidance, commercial-request instructions, and a careful assessment of replacement options. It also distinguishes confirmed drop-in substitutes from functional alternatives that would require engineering review, helping designers avoid treating similar op amps as automatic PCB replacements.
TS944ID - 4-Channel 10kHz Micropower Op Amp | STMicroelectronics
STMicroelectronics TS944ID is a four-channel general-purpose operational amplifier with rail-to-rail output, a 10 kHz gain-bandwidth product, and approximately 1.2 uA supply current per amplifier. The device is packaged in a 14-pin SOIC and operates from 2.5 V to 10 V across a -40°C to +85°C temperature range. Its four amplifiers make it suitable for compact, low-power analog signal-conditioning systems requiring several amplifier stages in one package. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TS944ID belongs to the micropower operational-amplifier family within the broader linear-amplifier and signal-conditioning hierarchy. Rail-to-rail output allows the amplifier to approach its supply limits more closely than fixed-output amplifiers, improving output swing in low-voltage systems where signal headroom is limited. The principal benefits of the TS944ID are integration, low power consumption, and rail-to-rail operation. Four amplifiers in one 14-pin SOIC reduce component count and board area compared with four separate single or dual amplifier packages. The 10 kHz gain-bandwidth product is suitable for low-frequency signal conditioning, including sensor buffers, transducer amplification, and general feedback-control networks. Its approximately 1.2 uA supply current is especially useful in battery-powered instrumentation where continuous analog circuitry must consume little power. The TS944ID is designed for general-purpose analog applications rather than high-speed signal processing. Its modest 10 kHz gain-bandwidth product favors slowly changing signals, such as sensor outputs, voltage references, and control-loop error amplifiers. The 2.5 V to 10 V operating range supports low-voltage battery systems, portable instruments, industrial monitoring circuits, and embedded control platforms. The -40°C to +85°C range covers industrial and commercial environments where extended automotive qualification is not required. Typical uses include four-channel sensor acquisition, portable measurement systems, low-frequency active filters, analog signal conditioning, and embedded control interfaces. Using one quad device for similar low-frequency channels can simplify routing and reduce package count. However, all four channels share common supply pins, so they cannot use independent positive and negative supply voltages. Input common-mode and output-swing behavior should also be checked against the actual signal range. When laying out a TS944ID board, place each bypass capacitor close to the device supply pins and keep feedback components near their associated amplifier inputs and outputs. Use short, quiet input paths for sensor signals and provide adequate return paths to minimize ground coupling. Avoid using this micropower amplifier where wide bandwidth, high output-current capability, or precision offset and drift specifications are essential; a higher-bandwidth or more accurate amplifier family will usually provide a better margin. This page combines the verified TS944ID ordering information, package and electrical characteristics, application guidance, pinout, and strict same-footprint replacement analysis. It also identifies where alternative data is unavailable, helping engineers distinguish confirmed device facts from options requiring a separate qualification review.
TS944IDT - Quad Micropower R-R Op Amp | STMicroelectronics
The STMicroelectronics TS944IDT is a quad micropower operational amplifier with CMOS inputs and rail-to-rail output swing, designed for four-channel signal conditioning from 2.5 V to 10 V in a 14-pin SOIC package. Its headline characteristics are a 1.2 µA supply current, 10 kHz gain-bandwidth product, and an operating temperature range from -40°C to +85°C. The four amplifiers share one package while operating from a common supply, making the TS944IDT suitable for compact, low-power instrumentation and sensor-processing systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two input terminals. The TS94x family belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, and general-purpose amplifiers. Rail-to-rail output capability allows the output voltage to approach the supply rails more closely than a conventional amplifier, improving output range in low-voltage systems where signal headroom is limited. The TS944IDT combines four rail-to-rail-output amplifiers, CMOS inputs, micropower consumption, and a 2.5 V to 10 V supply range. Its 10 kHz gain-bandwidth product favors low-frequency amplification rather than high-speed signal processing. The 1.2 µA operating current is particularly useful for battery-operated equipment, portable sensors, and low-duty-cycle monitoring systems where each milliamp of supply current can shorten operating time. According to the STMicroelectronics TS94x datasheet, the TS944IDT provides four amplifier circuits in a 14-pin small-outline package. CMOS input transistors support low-bias operation, while the rail-to-rail output stage increases usable output swing. The combination of four independent channels and low power consumption allows a compact design to replace several discrete single amplifiers while reducing board area and the number of required supply connections. Typical applications include low-frequency sensor conditioning, battery-powered instrumentation, portable measurement systems, industrial monitoring, and low-current feedback networks. The TS944IDT is best suited to signals whose bandwidth does not require the substantially higher gain-bandwidth product of a general-purpose precision amplifier. Designers should verify that the required closed-loop gain, output load, input common-mode range, and noise performance fit the application. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier channels should be configured according to the manufacturer datasheet rather than left without a defined operating state. This page combines the TS944IDT technical characteristics, verified sourcing information, drop-in alternatives, and application guidance to support component selection, PCB planning, and low-power analog design.
TS944IN - 4-Channel 10 kHz Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS944IN is a four-circuit, general-purpose operational amplifier with rail-to-rail output, a 10 kHz gain-bandwidth product, and a typical supply current of 1.2 uA per amplifier. It operates from 2.5 V to 10 V over a -40 C to +85 C temperature range and is packaged for through-hole mounting in a 14-DIP package. An operational amplifier, or op amp, is a high-gain analog signal-processing IC used to compare an input with a feedback-defined reference, amplify weak signals, buffer voltage sources, and implement active analog filters. Within the component hierarchy, the TS944IN is a quad operational amplifier, a type of linear amplifier and analog IC intended for low-power signal-conditioning systems. The TS944IN family emphasizes low power consumption and rail-to-rail output operation. Its 10 kHz gain-bandwidth product supports low-frequency amplification and filtering, while the 4.5 mV/us slew rate limits how quickly its output can change. Typical input bias current is 1 pA, which is useful when high-impedance sensors or sensing nodes must not be loaded heavily. The listed typical input offset voltage is 10 mV. STMicroelectronics describes the TS94x family as rail-to-rail micropower operational amplifiers for 2.5 V to 10 V operation. Four amplifiers in one package reduce board area and simplify design for systems that need several independent analog channels. The TS944IN is identified as a general-purpose amplifier and an obsolete catalog item, so lifecycle planning should account for its non-active status. Typical circuit roles include battery-powered sensor interfaces, low-frequency active filters, portable measurement systems, and general-purpose signal conditioning. Because the gain-bandwidth product is only 10 kHz, the device is better suited to slow analog signals than to high-speed waveform or video paths. Its rail-to-rail output also requires careful review of the input common-mode range for each operating condition. Design with the TS944IN using supply bypassing close to the power pins and verify each amplifier's feedback network, output load, input bias requirements, and stable operating gain. Because the input offset voltage can reach 10 mV typ. in the published summary, precision measurements may require calibration, offset correction, or a higher-accuracy amplifier. This page organizes the manufacturer specifications, lifecycle status, sourcing path, and practical application guidance for TS944IN. It also distinguishes genuine same-footprint replacements from different-package family members, helping engineers avoid substitutions that require PCB changes.
TS944IPT - Quad Rail-to-Rail 1.2µA Op-Amp | STMicroelectronics
The STMicroelectronics TS944IPT is a quad CMOS-input operational amplifier delivering rail-to-rail output swing while consuming only 1.2 µA typical quiescent current per channel, packaged in a 14-pin TSSOP (Tape & Reel). It operates from a single 2.5 V to 10 V supply over the -40 °C to +85 °C industrial temperature range and provides a gain-bandwidth product of 10 kHz, making it ideal for ultra-low-power signal conditioning. An operational amplifier (op-amp) is a high-gain DC-coupled differential amplifier that uses external feedback components to set closed-loop gain, bandwidth, and transfer function. The TS944 belongs to the micropower CMOS op-amp family — a class of linear ICs that prioritize nano- to micro-amp quiescent current draw for battery-powered and energy-harvesting designs. Within the broader semiconductor hierarchy, it sits under: op-amp -> amplifier -> analog IC -> linear IC -> integrated circuit. Key features include four independent op-amp channels in one package, CMOS inputs delivering ultra-low input bias current, rail-to-rail output swing that maximizes dynamic range on low-voltage supplies, and 1.2 µA typical supply current per amplifier that enables years of runtime from small cells. The device is unity-gain stable and supports single-supply operation from 2.5 V to 10 V, simplifying designs that previously needed bipolar ±5 V rails. The TS944 architecture uses a CMOS input stage that achieves very low bias current while the class-AB output stage swings to within millivolts of both supply rails. This combination eliminates the need for input bias-current compensation in high-impedance sensor interfaces and lets designers operate the part directly from a single lithium cell or 3.3 V digital rail without sacrificing headroom. Typical applications include battery-powered sensor signal conditioning, portable medical monitors, IoT edge nodes, active filters, transducer pre-amplifiers, and any micropower analog front end where four amplifiers must fit in a small 14-pin TSSOP footprint. Designers should bypass supplies with 100 nF ceramic capacitors placed within 5 mm of VCC and avoid capacitive loads above 1 nF without an isolation resistor to prevent oscillation.
TS951ID - 3MHz Rail-to-Rail Low-Power Op Amp | STMicroelectronics
STMicroelectronics TS951ID is a single-amplifier, input/output rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a maximum operating supply voltage of 12 V and operation from the negative rail to the positive rail at input and output. The device is packaged in an 8-pin SOIC and provides approximately 3 MHz gain-bandwidth product, 1 V/µs slew rate, and 80 dB supply-voltage rejection ratio. Its low-power design targets portable instrumentation, sensor interfaces, audio signal conditioning, and general-purpose analog systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while offering high input impedance, low output impedance, and stable closed-loop behavior when feedback is applied. The TS951 belongs to the operational-amplifier hierarchy, where its BiCMOS input stage combines bipolar transistor performance with CMOS power efficiency. Rail-to-rail input and output operation extends useful signal range toward the supply rails, making the amplifier practical in low-voltage systems that cannot tolerate substantial headroom loss. Key benefits include 3 MHz gain-bandwidth product for modest-frequency signal paths, 1 V/µs slew rate for faster large-signal transitions, and 80 dB supply rejection for reducing supply ripple that could otherwise modulate the amplified signal. The low-power operating approach is useful in portable equipment where energy efficiency and reduced heat generation are priorities. ESD protection rated at 2 kV adds handling robustness, while the compact SOIC-8 package supports conventional surface-mount assembly. The BiCMOS architecture is appropriate for precision and general-purpose analog blocks where low quiescent consumption and rail-to-rail signal handling are more important than high-speed performance. Because this amplifier is intended for low-power rather than high-bandwidth signal chains, applications normally use moderate feedback resistors, explicit gain-setting resistors, and stable output-loading arrangements. Its broad supply capability also permits operation from 3 V and 5 V rails, although each operating point should be checked against the complete electrical limits in the manufacturer datasheet. Typical applications include low-voltage sensor conditioning, buffered analog measurements, portable audio paths, general-purpose instrumentation, and interface buffering around higher-impedance sensors. It can also support low-frequency control or active-filter stages where the 3 MHz gain-bandwidth product provides useful bandwidth margin. In these systems, TS951ID can reduce the loading imposed on the sensor source while maintaining an output signal referenced to the available supply range. Designers should verify input common-mode range, output swing, output-current capability, noise, and stability at the intended frequency before committing the device to a new layout. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths. The input and feedback networks must also avoid excessive source resistance or capacitance that could impair stability. This product data combines the verified STMicroelectronics family description, manufacturer datasheet, and distributor listings with practical guidance for package selection, sourcing, and analog layout. It also distinguishes electrically related family members from true drop-in choices and identifies unavailable pricing and lifecycle information rather than presenting unverified commercial figures.
TS951IDT - 3 MHz Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS951IDT is a single-circuit, rail-to-rail input/output low-power operational amplifier with a 3 MHz gain-bandwidth product, 1 V/us slew rate, and operation from 2.7 V to 12 V in an 8-pin SOIC package. Designed for instrumentation, buffer, and general-purpose signal-conditioning applications, it combines 750 uA quiescent current with rail-to-rail input and output capability. An operational amplifier, commonly called an op amp, is an active semiconductor component that amplifies the voltage difference between its two inputs. A rail-to-rail input stage accepts common-mode voltages close to either supply rail, while a rail-to-rail output stage can approach the output limits more closely than a conventional amplifier. The TS951IDT belongs to the general-purpose operational-amplifier hierarchy and is suitable for low-voltage analog systems that require useful signal range, moderate bandwidth, and low standby current. Key characteristics include a 3 MHz gain-bandwidth product, 1 V/us slew rate, approximately 750 uA quiescent current, and a 2.7 V to 12 V supply range. These attributes suit low-power sensor conditioning, buffered instrumentation, audio signal paths, and general analog signal processing. Rail-to-rail input and output operation is particularly useful when signals approach the supply limits or when the amplifier must drive loads with limited voltage headroom. The TS951IDT uses a BiCMOS operational-amplifier architecture optimized for 3 V and 5 V operation. Its moderate 3 MHz bandwidth provides adequate response for general-purpose signal conditioning without the power and cost of a high-speed amplifier. The 1 V/us slew rate supports noncritical pulse and waveform applications, while the low quiescent current helps conserve energy in portable and battery-powered equipment. Exact offset, noise, output-current, and temperature data must be confirmed in the manufacturer datasheet. Typical uses include sensor-signal conditioning, analog instrumentation, voltage buffering, audio preamplification, and low-voltage control systems. The TS951IDT can also serve as the active element in passive or active filter designs when component tolerances and loop-gain requirements permit. In portable equipment, its low quiescent current is advantageous, although input bias current and overall system demand should be evaluated before battery-life calculations. For PCB design, place input, output, and decoupling components close to the SOIC pins. Keep sensitive input traces away from switching nodes and high-current return paths, and use a ground plane that provides a low-impedance return for the amplifier. Bypass the supply pins locally with suitable ceramic capacitance and account for amplifier output loading, stability, and input common-mode limits during schematic review. This product page combines the TS951IDT electrical identity, package information, sourcing guidance, application analysis, design guidance, and verified replacement search results. It is intended to help engineers identify whether the TS951IDT matches the required bandwidth, supply voltage, package, and low-power characteristics before committing it to a design.
TS951IN - 3MHz Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS951IN is a single-circuit, general-purpose BiCMOS operational amplifier featuring a 3 MHz gain-bandwidth product, a 1 V/µs slew rate, and input/output rail-to-rail operation in an 8-DIP package. The amplifier is optimized for 3 V and 5 V operation and can also operate from a supply as high as 12 V. Its low-power design consumes approximately 0.9 mA when operated from a 3 V supply, making it suitable for portable, instrumentation, sensor, and general analog signal-conditioning systems. An operational amplifier is an active analog component that amplifies the difference between its inverting and non-inverting inputs. The TS951IN belongs to the rail-to-rail operational-amplifier category and uses a BiCMOS process that combines CMOS input characteristics with bipolar output-drive capability. Rail-to-rail input common-mode range allows the amplifier to sense signals near the positive and negative supply rails, while rail-to-rail output swing improves dynamic range when the available supply voltage is limited. Key electrical characteristics include a 3 MHz gain-bandwidth product, 1 V/µs slew rate, and approximately 0.9 mA supply current at 3 V. The 3 MHz bandwidth provides useful speed for audio-frequency buffers, general-purpose signal amplification, active filters, and sensor interfaces, while the 1 V/µs slew rate permits relatively rapid output transitions. The 8-DIP package supports straightforward through-hole assembly and is suitable for prototypes, educational platforms, and applications where a larger package is acceptable. The TS951IN is built for general-purpose precision and moderate-speed analog work. Its single-amplifier configuration simplifies designs that require one independent signal path, while the low-power operating mode can reduce total system consumption in battery-powered equipment. Because a bipolar output stage is present, careful assessment of output-current capability, capacitive-load stability, and operating temperature is appropriate before assigning it to demanding loads. Typical applications include low-frequency audio buffer stages, sensor-signal conditioning, active filters, data-acquisition front ends, portable instrumentation, and general analog signal conditioning. The rail-to-rail input capability is especially useful when sensor outputs can approach either supply rail. The rail-to-rail output stage is beneficial in low-voltage systems where a conventional amplifier would clip before approaching the available output range. When designing with the TS951IN, keep feedback routing short, place compensation and decoupling components close to the device, and verify stability with the actual source impedance and load. Connect the unused input to a defined reference potential, normally the non-inverting input or a mid-supply bias point. Do not substitute a modern CMOS or rail-to-rail amplifier without checking input offset, bias-current, noise, output-drive, and supply-current differences. This page combines manufacturer family information, distributor identification, package information, and practical design guidance with a parameter comparison against same-package family alternatives. It also distinguishes the TS951IN from the TS952 and TS954 family members, whose electrical characteristics must be checked against the manufacturer datasheet before making a board-level substitution.
TS952ID - Dual 3MHz Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS952ID is a dual, input/output rail-to-rail BiCMOS operational amplifier with a 3 MHz gain-bandwidth product, 1 V/us slew rate, and operation from 2.7 V to 12 V in an 8-pin SOIC package. It is optimized and specified for both 3 V and 5 V supply rails, making it suitable for low-voltage analog systems that require an amplifier to approach its supply limits at the input and output. An operational amplifier, or op amp, is a high-gain analog building block used in amplification, buffering, filtering, sensing, and feedback-control circuits. The TS952 belongs to the rail-to-rail op-amp category within the broader amplifier IC and signal-chain hierarchy. Rail-to-rail input and output behavior allows signals near either supply rail to be processed with less conventional headroom loss than a fixed-input amplifier. The TS952ID provides two amplifier circuits, a 3 MHz bandwidth, and a 1 V/us slew rate. According to the STMicroelectronics TS952 product-page data, the device is optimized for 3 V and 5 V operation. Other identified features include an 80 dB supply-voltage rejection ratio, 2 kV ESD protection, and low-power operation. These characteristics make the part applicable to low-voltage sensor conditioning, portable instrumentation, audio input stages, and general-purpose analog signal processing. The BiCMOS architecture combines bipolar input-stage behavior with CMOS output circuitry and is intended to balance low-voltage operation, amplifier performance, and power efficiency. Because the TS952 is a dual device, two independent amplifier channels can share one package. The 8-pin SOIC outline also supports conventional surface-mount assembly, although final stability, bandwidth, and output-current behavior must be evaluated at the intended supply voltage and load. Typical uses include battery-powered sensor interfaces, buffered analog inputs, portable measurement systems, audio preamplification, and low-voltage control loops. At 3 V, the device is aligned with compact battery-operated systems; at 5 V, it provides additional signal range for industrial and consumer analog circuits. The 3 MHz bandwidth is sufficient for many general-purpose conditioning stages but is not intended for high-speed video or precision wideband instrumentation without further analysis. When designing around the TS952ID, verify input and output common-mode limits, output swing, load capability, noise, offset, and stability for the selected supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should remain short and away from switching nodes. Feedback components should follow the manufacturer recommendations because gain-bandwidth, input capacitance, and capacitive loading can affect closed-loop behavior. This product record combines the verified STMicroelectronics family description, distributor package information, operating range, bandwidth, slew rate, rejection, and ESD information with practical selection guidance. It also distinguishes verified facts from specifications that still require confirmation from the complete manufacturer datasheet, avoiding unsupported claims about electrical limits or replacement parts.
TS952IN - Dual 3MHz Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS952IN is a dual, low-power operational amplifier with input and output rail-to-rail capability, a 3 MHz gain-bandwidth product, and a 1 V/us slew rate. It operates from 2.7 V to 12 V and is packaged in an 8-pin Mini DIP. The device belongs to the TS95x family, whose BiCMOS architecture is optimized and fully specified for 3 V and 5 V operation. An operational amplifier is a voltage-controlled differential amplifier that can amplify the difference between two input voltages while providing high open-loop gain. The TS952IN contains two independent amplifier channels in one package. Rail-to-rail input operation lets each channel accept signals close to the positive or negative supply rail, while rail-to-rail output operation allows the output voltage to approach either supply limit. These characteristics make the device useful for portable instrumentation, sensor interfaces, audio paths, and low-voltage control systems. The 3 MHz gain-bandwidth product supports useful bandwidth in low-voltage signal chains without requiring a high-speed amplifier operating from a larger supply. The 1 V/us slew rate helps limit large-signal distortion when signals change quickly. Because the TS95x family is designed for low-power operation, the TS952IN is also appropriate for battery-powered equipment where a pair of independent amplifiers is useful without using two separate packages. The device is specified for a 2.7 V to 12 V supply range, with its family optimized for 3 V and 5 V systems. At low supply voltages, rail-to-rail behavior becomes especially valuable because it increases the usable input and output range relative to conventional fixed-output amplifiers. Designers should still verify the actual output swing, input common-mode range, noise, input bias current, output-current capability, and stability requirements against the manufacturer datasheet for the operating point of interest. Typical applications include buffering sensor outputs, amplifying low-level analog signals, active filtering, audio preamplification, and general-purpose signal conditioning. In a sensor interface, one channel can amplify the sensor signal while the other can provide buffering, gain, or a reference-related function. Supply bypassing, output-load compatibility, and stability with the selected feedback network are important implementation considerations for this general-purpose dual amplifier. This product page combines the verified TS952IN operating characteristics, package information, drop-in replacement findings, application guidance, and practical design notes. It is intended to help engineers identify the correct amplifier quickly, compare pin-compatible choices, and plan PCB and signal-chain changes before releasing a new design.
TS952IPT - Dual Low-Power Rail-to-Rail Amplifier | ST
The STMicroelectronics TS952IPT is a dual, low-power operational amplifier with rail-to-rail input and rail-to-rail output capability, 35 nA input bias current, 1 V/us slew rate, 3 MHz gain-bandwidth product, and 6 mV input offset voltage in an 8-pin TSSOP package. Designed for 3 V and 5 V systems, it combines two amplifier channels in one compact surface-mount package. An operational amplifier is a high-gain analog signal-processing component that compares its differential input with a feedback-defined reference and amplifies the resulting error. The TS952IPT belongs to the rail-to-rail input/output amplifier class, allowing its input and output stages to operate close to the supply rails. This makes it useful in portable instruments, sensor interfaces, battery-powered equipment, and low-voltage industrial control systems where signal headroom is limited. Key characteristics include a low 35 nA input bias current, which reduces loading on high-impedance sources, and a 3 MHz gain-bandwidth product that supports moderate-speed signal paths. Its 1 V/us slew rate improves large-signal response, while rail-to-rail input and output stages increase usable signal range in single-supply systems. The dual configuration also reduces board area by integrating two amplifiers into one package. The TS952IPT uses a low-power BiCMOS operational-amplifier architecture. The architecture combines bipolar input behavior with CMOS-compatible output drive and low-power operation. In practical circuits, input common-mode range, output swing, output-current capability, noise, and stability with the selected feedback network determine whether it is suitable for a particular precision or signal-conditioning stage. Typical applications include low-voltage sensor amplification, photodiode-biased readout stages, portable measurement equipment, audio signal conditioning, general-purpose buffer circuits, and industrial control interfaces. The 3 V and 5 V operating environments align the device with battery-powered products, data-acquisition modules, embedded systems, and compact instrumentation. When designing a PCB around the TS952IPT, follow the manufacturer datasheet for decoupling, exposed pad or thermal guidance, input capacitance, and output-load limitations. Place the input and output bypass capacitors close to their associated pins, maintain short feedback paths, and verify stability with the actual source impedance and capacitive load. This product page combines the TS952IPT technical characteristics, sourcing information, package guidance, practical application notes, and replacement analysis. It is designed to help engineers identify the correct low-power amplifier and plan a robust implementation without changing the established 8-pin TSSOP footprint.
TS952IYD - Dual Rail-to-Rail Low-Power Op Amp | STMicroelectronics
The STMicroelectronics TS952IYD is a dual-amplifier operational amplifier optimized for low-power operation at 3 V and 5 V. It provides input and output rail-to-rail capability in an 8-pin SOIC package, making it suitable for portable equipment, sensor interfaces, and low-voltage signal-conditioning systems. The TS95x family combines two amplifiers per package to improve board utilization while retaining compact, surface-mount construction. An operational amplifier is an analog signal-conditioning device that uses external feedback to amplify voltage differences between its differential inputs. A rail-to-rail input stage accepts signals extending close to the positive or negative supply rail, while a rail-to-rail output stage can swing its output toward those rails. This capability is useful when signal levels occupy much of the available supply-voltage range and conventional input or output stages would otherwise introduce avoidable clipping. The TS952IYD is identified as a standard general-purpose, input/output rail-to-rail, low-power amplifier. Its two-circuit configuration supports independent signal paths within one package. The manufacturer describes the TS95x family as optimized and fully specified for 3 V and 5 V operation, giving designers a clear basis for portable and embedded applications that operate from low-voltage rails. The SOIC-8 package also supports conventional surface-mount assembly and inspection. The family's low-power orientation is significant because analog performance depends on more than nominal gain. Supply current, input bias behavior, output swing, noise, and the usable common-mode range determine whether an amplifier can process small sensor signals without consuming excessive energy or clipping near the rails. Exact electrical limits should be selected against the manufacturer's operating tables for the intended supply voltage and temperature range. Typical uses include battery-powered sensor conditioning, portable audio and communication interfaces, current measurement, low-voltage data acquisition, and embedded control systems. Two amplifiers can also implement independent gain stages, buffer functions, or active filtering when each channel requires its own feedback network. When both channels operate close to the supply rails, decoupling and grounding become especially important for preserving signal integrity. For implementation, place the bypass capacitor adjacent to the supply pins and connect the two ground pins to a low-impedance ground plane. Avoid long feedback traces and route sensitive input and output nets away from switching nodes. Confirm that the required input range, output swing, gain-bandwidth behavior, and load current remain within the manufacturer's limits at the actual supply voltage. This product page combines the TS952IYD device identity, package information, sourcing guidance, application context, and practical layout considerations. It also distinguishes directly documented characteristics from parameters that must be confirmed in the manufacturer datasheet, helping engineers plan a reliable low-voltage analog design without relying on generic operational-amplifier assumptions.
TS954ID - Quad 3MHz R-to-R Op Amp | STMicroelectronics
The STMicroelectronics TS954ID is a quad rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a 3 MHz gain-bandwidth product and 1 V/µs slew rate in a 14-pin SOIC package. The four amplifiers support supply voltages from 2.7 V to 12 V and combine low-power operation with low input bias current. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. A rail-to-rail output amplifier can approach the supply rails at its output, making it useful when the available signal range is small. The TS954 belongs to the amplifier IC hierarchy, where operational amplifiers are used for signal conditioning, buffering, active filtering, comparisons, and analog sensor interfaces. The TS954 family provides four amplifiers per package, a 3 MHz gain-bandwidth product, and a 1 V/µs slew rate. Its input bias current is 35 nA, while the listed supply current is 950 µA per channel. These characteristics make it suitable for general-purpose signal conditioning operating from 2.7 V to 12 V, including low-voltage analog systems and battery-powered equipment. The device uses a BiCMOS input architecture combining bipolar and CMOS process characteristics. Its rail-to-rail output stage allows useful output swing near the supply limits, while the low 35 nA input bias current reduces current errors when driving high-impedance sources. The 3 MHz bandwidth is adequate for audio-frequency and general instrumentation tasks, whereas applications requiring substantially faster closed-loop settling should use a higher-bandwidth amplifier. Typical uses include low-level sensor amplification, active analog filters, audio signal conditioning, instrumentation, and four-channel buffering. The SOIC-14 package permits conventional surface-mount assembly and provides one amplifier per two package pins. Its quad configuration can also reduce board area compared with four separate single or dual amplifier packages when all four channels are required. Designers should verify the required output swing, load impedance, input common-mode range, noise performance, and stability against the manufacturer datasheet before finalizing a circuit. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased according to the manufacturer recommendations so that input and output stages remain in their intended operating regions. This page consolidates verified manufacturer and distributor information for the TS954ID, including the 3 MHz bandwidth, 1 V/µs slew rate, 2.7 V to 12 V supply range, 14-pin SOIC format, sourcing links, and the engineering trade-offs that distinguish a low-power quad amplifier from faster or more specialized alternatives.
TS954IDT - Quad Rail-to-Rail Low-Power Op Amp | STMicroelectronics
The STMicroelectronics TS954IDT is a quad input/output rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a 2.7 V to 12 V supply-voltage range and four amplifiers in a 14-pin SOIC package. Its rail-to-rail input and output stages support operation close to the supply rails, making the device suitable for portable, industrial, and instrumentation systems that require low-voltage signal conditioning. An operational amplifier is an analog signal-conditioning semiconductor that compares two input voltages and amplifies the difference between them. A quad operational amplifier contains four independent amplifier channels in one package. The rail-to-rail BiCMOS category combines complementary bipolar input characteristics with CMOS output stages, while the low-power design targets portable and space-constrained applications. The TS954IDT provides four rail-to-rail amplifier channels, low-noise input behavior, low distortion, and operation from 2.7 V to 12 V. The manufacturer describes the family as optimized and fully specified for 3 V and 5 V systems. Rail-to-rail input operation improves usable input range, while rail-to-rail output capability allows output voltage to approach the available supply voltage more closely than a conventional non-rail-to-rail output amplifier. The TS954 family combines four general-purpose amplifiers with a 14-pin SO package. It is intended for applications where several independent analog channels are required, including sensor conditioning, buffer amplification, active filtering, low-level signal processing, and embedded control systems. The shared package consolidates four channels without requiring four separate amplifier packages, reducing board-area requirements. Typical uses include portable measurement equipment, industrial sensor interfaces, audio and communications signal conditioning, battery-powered instruments, and general-purpose analog subsystems. The 2.7 V minimum supply supports 3 V systems, while the 12 V maximum provides flexibility for 5 V and higher-voltage designs when the applied operating point remains within the device ratings. When designing around the TS954IDT, verify input and output common-mode limits, output-current demand, capacitive-load stability, and supply voltage for every channel. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should be routed away from switching nodes and high-current return paths to preserve low-noise operation. This product page combines the manufacturer datasheet information with practical application guidance, package details, technical comparisons, and drop-in replacement options. It is intended to help engineers select the correct amplifier, plan the PCB, and assess whether a same-package alternative can simplify an existing design without unnecessary board changes.
TS954IN - 3MHz Quad Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS954IN is a quad input/output rail-to-rail low-power BiCMOS operational amplifier optimized for 3V and 5V operation. Its four amplifiers, 3 MHz gain-bandwidth product, 1 V/us slew rate, and 14-DIP package make it suitable for compact analog signal-conditioning systems requiring low-voltage supply operation. The input and output stages support rail-to-rail signal handling, while the 80 dB supply-voltage rejection specification helps suppress supply-related signal distortion. An operational amplifier is an active semiconductor device that amplifies the voltage difference between its differential inputs. Rail-to-rail input capability means the input common-mode range can extend toward both supply rails, while rail-to-rail output capability allows the output voltage to approach the operating limits more closely than a conventional non-rail-to-rail amplifier. The TS954IN belongs to the TS95x family of low-power BiCMOS operational amplifiers optimized for single-supply systems. Key characteristics include four amplifier channels in one package, a 3 MHz gain-bandwidth product, and a 1 V/us slew rate. These specifications support applications such as sensor interfaces, buffered analog signals, low-voltage instrumentation, audio paths, and general-purpose analog conditioning. The TS954IN is also identified as ESD protected to 2 kV and includes latch-up protection according to the manufacturer datasheet information. The BiCMOS architecture combines bipolar input characteristics with CMOS power-handling behavior. This implementation supports low-power operation while maintaining a useful small-signal bandwidth for sensor, filtering, and signal-buffer circuits. At a 3V supply, the family is specifically optimized for low-power consumption, which makes it relevant to portable equipment and embedded analog systems that cannot justify a higher-power precision amplifier. Typical uses include buffering sensor outputs, amplifying low-level analog signals, active filtering, level shifting, audio preamplification, and instrumentation. The quad organization reduces package count when several independent analog channels are required. Designers should still evaluate input offset voltage, input bias current, output-current capability, noise, and stability for the exact gain, load, and supply conditions before finalizing a circuit. The principal design consideration is operating margin. Rail-to-rail inputs and outputs do not remove the requirement to maintain adequate input and output voltage limits, especially under load. Decoupling capacitors should be placed close to the supply pins, and feedback networks should be designed to preserve the intended closed-loop gain while avoiding output saturation. This product page combines the manufacturer family description with practical application guidance, parameter comparison, and pin-package considerations. It is intended to help engineers determine whether the TS954IN's four-channel 3V/5V rail-to-rail architecture fits a board-level design before consulting the complete manufacturer datasheet for limit values and test conditions.
TS971ID - 12MHz Low-Noise Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS971ID is a single, rail-to-rail output operational amplifier with 12 MHz gain-bandwidth product, 4 V/µs slew rate, 4 nV/√Hz input-noise density, and 0.003% ultra-low distortion. The device operates from 2.7 V to 10 V and is supplied in an 8-pin SOIC package. Its combination of low noise, high gain bandwidth, rail-to-rail output swing, and wide supply range makes it suitable for portable audio, instrumentation, sensor conditioning, and general-purpose signal-processing circuits. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The TS971ID belongs to the operational-amplifier hierarchy within analog and mixed-signal ICs. Rail-to-rail output means the output can swing close to either supply rail, improving usable output range in low-voltage systems. The single-amplifier configuration also keeps the package compact for cost-sensitive designs requiring one precision analog channel. The principal performance features include 12 MHz gain bandwidth and a 4 V/µs slew rate, allowing the amplifier to process relatively fast signals without excessive settling limitations. Input-noise density is specified at 4 nV/√Hz, and the listed distortion is 0.003%. According to the STMicroelectronics product family information, TS97x devices can operate with supply voltages as low as ±1.35 V and are intended for portable and battery-powered equipment. The TS971ID combines rail-to-rail output operation with low-noise and low-distortion behavior. ESD protection is listed at 2 kV, while latch-up immunity is identified as Class A. These characteristics are particularly useful when a circuit must preserve small-signal information while operating from a constrained supply. The amplifier's 2.7 V to 10 V operating range supports conventional 3.3 V, 5 V, and up-to-10 V system rails. Typical uses include microphone and line-level audio preamplification, portable measurement equipment, low-level sensor interfaces, active filters, and buffered sensor outputs. In an audio preamplifier, the 4 nV/√Hz noise density helps limit the amplifier's contribution to the system noise floor. In instrumentation, the 12 MHz bandwidth provides useful signal range, while the 0.003% distortion specification supports high-fidelity signal paths. When designing a TS971ID circuit, verify the input and output common-mode limits, operating-voltage range, output-current capability, and stability requirements against the manufacturer datasheet. Place input, output, and compensation-network components close to the device, and use a suitable output-load arrangement. Because the verified search results do not provide a public price or a complete manufacturer pin table, those details are not inferred here.