Amplifier ICs
بەرهەمەکان (3,200+)
TS971IDT - 12 MHz Rail-to-Rail Low-Noise Op Amp, SOIC-8 | STMicroelectronics
The STMicroelectronics TS971IDT is a single rail-to-rail output, very low-noise operational amplifier with a 12 MHz gain-bandwidth product and a 4 V/us slew rate, operating from 2.7 V to 10 V in an 8-pin SOIC package. It is a standard general-purpose amplifier in the TS9xx family, built for single-supply and dual-supply analog signal chains where the output must swing close to both rails. An operational amplifier, commonly shortened to op amp, is an analog differential-input amplifier whose closed-loop behavior is set by external feedback components. Within the electronic component hierarchy an op amp sits in the analog amplifier class, alongside instrumentation and buffer amplifiers, all of which fall under the broader category of amplifier integrated circuits used for conditioning, scaling and buffering low-level signals. The TS971IDT occupies the high-speed end of that spectrum, offering enough bandwidth for video, filter and fast sensor interfaces rather than the slow precision of micropower parts. Key characteristics of this device include a single amplifier per package, rail-to-rail output operation, and a very low-noise architecture. Because the output stage swings to the positive and negative supply rails, the amplifier can drive downstream circuitry without leaving a headroom-limited region, which matters in single 3.3 V or 5 V systems where the usable signal range is already narrow. The 12 MHz gain-bandwidth product pairs with the 4 V/us slew rate so that full-scale swings are reproduced without the soft edges typical of low-bandwidth amplifiers. The TS97x family is offered in several packages to suit different board constraints. As noted in the manufacturer documentation, space-critical designs can use the SOT23-5 (2.8 x 2.9 mm) or DFN8 (3 x 3 mm) versions of the TS97x devices, while the TS971IDT itself ships in the industry-standard 8-pin SOIC outline that most assembly houses and prototype boards already support. Supply options run from 2.7 V to 10 V in total, or from 1.35 V to 5 V for single-supply operation. Typical uses include sensor signal conditioning in industrial and IoT equipment, active filtering and audio path amplification, and general-purpose buffering ahead of analog-to-digital converters. In these roles the rail-to-rail output recovers maximum signal swing from a low supply, while the wide bandwidth preserves fast transients rather than rounding them off. When laying out a design around the TS971IDT, place the bypass capacitors close to the supply pins and keep the feedback network short, since long traces add parasitic capacitance that can affect stability in high-gain configurations. Confirm that the required output swing, load current and supply noise budget match the application before fixing the gain structure in place. This page consolidates manufacturer documentation, distributor availability information, drop-in alternatives drawn from the TS9xx family, and practical design guidance that a single distributor listing does not provide on its own, giving engineers the context needed to select and land the part correctly.
TS971ILT - 12 MHz Low-Noise R-R Operational Amplifier | STMicroelectronics
The STMicroelectronics TS971ILT is a single, very low-noise operational amplifier with rail-to-rail output swing, 12 MHz gain-bandwidth product, and 4 V/us slew rate, supplied in a 5-pin SOT-23 package. It operates from 2.7 V to 10 V and is intended for compact battery-powered and portable signal-conditioning circuits. An operational amplifier is an analog active component that uses high-gain feedback to amplify voltage differences. The TS971 belongs to the operational-amplifier hierarchy, which includes general-purpose amplifiers, rail-to-rail input/output amplifiers, low-noise amplifiers, and precision signal-chain devices. Its rail-to-rail output allows the output voltage to approach the supply rails, improving utilization of available supply voltage in portable equipment. The TS971ILT combines low-noise operation with a 12 MHz gain-bandwidth product and 4 V/us slew rate. These characteristics make it useful for audio preamplification, sensor conditioning, active filtering, and low-level signal amplification where bandwidth and noise must be balanced. The single-amplifier configuration also reduces board area compared with dual or quad devices. The device supports supply voltages as low as 2.7 V and is characterized for operation up to 10 V. Its SOT-23-5 package is suitable for surface-mount construction, although the exposed thermal limitations of the small package require attention when driving capacitive loads or operating continuously at high output swing. The input common-mode behavior and output swing should be checked against the system supply rails in the manufacturer datasheet. Typical uses include portable audio signal paths, microphone and sensor interfaces, low-frequency filters, and general instrumentation. For battery-powered systems, the low-voltage operation can simplify power architecture and reduce the need for a higher-voltage analog rail. In signal-chain designs, the low-noise characteristics help preserve weak signals before conversion or measurement. Place input and output decoupling capacitors close to the device pins, keep analog traces short, and provide adequate return-current paths. Verify stability with the source and load impedances used in the final circuit, especially when driving long capacitive loads. This page combines manufacturer-family details, package information, pricing structure, replacement guidance, and practical design notes for faster component selection.
TS972ID - 12 MHz Dual Rail-to-Rail Low-Noise Op Amp | STMicroelectronics
STMicroelectronics TS972ID is a dual, output rail-to-rail, very-low-noise operational amplifier with 12 MHz gain-bandwidth product, 4 V/us slew rate, and operation from 2.7 V to 10 V in an 8-pin SOIC package. Its principal characteristics are 4 nV/Hz noise density, 0.003% distortion, and the ability to operate with supply voltages as low as ±1.35 V. These ratings position the TS972ID as a precision amplifier for portable, battery-powered, audio-preamplifier, and low-noise signal-conditioning systems. An operational amplifier, or op amp, is a high-gain differential amplifier whose feedback network determines its closed-loop behavior. Within the integrated-circuit hierarchy, the TS972ID belongs to the operational-amplifier class, amplifier IC category, and broader analog and mixed-signal semiconductor family. Rail-to-rail output capability lets its output approach the supply rails more closely than a conventional amplifier, improving usable output swing in compact low-voltage systems. The TS972ID combines three defining benefits: 12 MHz gain-bandwidth product for moderate-frequency amplification, 4 V/us slew rate for faster signal transitions, and 4 nV/Hz input-voltage noise for low-noise operation. A 0.003% distortion figure further supports high-fidelity signal paths. The dual configuration provides two amplifiers in one 8-pin SOIC, reducing board area compared with two separate single-channel packages. Its low-voltage operating range and rail-to-rail output architecture suit systems that cannot tolerate the headroom required by conventional amplifiers. The 2.7 V to 10 V supply specification permits operation from a single 3.3 V rail, dual ±2.5 V rails, or other compatible supplies. The manufacturer description specifically identifies portable and battery-powered equipment as suitable markets, while the noise and distortion specifications make audio preamplification a natural fit. Typical uses include portable audio preamplifiers, low-noise sensor conditioning, microphone stages, active filters, and buffered sensor outputs. Two amplifiers in one package can implement dual signal channels, instrumentation front ends, or complementary gain stages when their independent inputs and outputs are required. Care is still necessary when driving capacitive loads, observing output-current limits, and controlling stability around the amplifier and feedback network. The primary design consideration is stable implementation of the intended gain. Input and feedback resistances should be selected consistently with the 12 MHz bandwidth and noise target, while board layout should minimize parasitic capacitance and feedback-loop coupling. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer guidance rather than left floating. This page consolidates the verified TS972ID operating limits, source references, and same-family alternatives with practical selection and layout guidance. It distinguishes documented facts from parameters requiring confirmation, making the result more useful for PCB compatibility reviews, sourcing, and amplifier design decisions.
TS972IN - Dual Low-Noise R2R Op Amp | STMicroelectronics
STMicroelectronics TS972IN is a dual operational amplifier with rail-to-rail output swing, very low noise of 4 nV/Hz, 12 MHz gain-bandwidth product, and 4 V/us slew rate. The device operates from dual supplies as low as ±1.35 V and is packaged for through-hole assembly in an 8-DIP package with 7.62 mm pin spacing. It is designed for signal conditioning applications where low-noise amplification, low distortion, and rail-to-rail output swing are important. An operational amplifier is an analog semiconductor that amplifies the voltage difference between its two inputs while using negative feedback to establish gain and bandwidth. The TS972IN belongs to the operational-amplifier hierarchy within analog ICs and interface signal-conditioning components. Its dual-circuit configuration provides two independent amplifiers in one package, reducing board area in audio, instrumentation, sensor, and portable-equipment designs. The TS972IN combines several performance characteristics suited to precision signal chains. Its 4 nV/Hz noise density supports low-noise preamplification, while its maximum distortion of 0.003% is useful in audio and measurement paths. A 12 MHz gain-bandwidth product supports wider-band signal amplification, and the 4 V/us slew rate improves large-signal response. Rail-to-rail output swing allows the output to approach the supply rails more closely than a conventional non-rail-to-rail amplifier. The TS97x family supports operation from voltages as low as ±1.35 V, making the TS972IN suitable for battery-powered and portable systems. Its specified operating range extends to 10 V. The device also includes 2 kV ESD protection and Class A latch-up immunity, helping improve interface robustness in sensitive applications. The dual amplifier uses an 8-DIP package for conventional PCB through-hole assembly. Typical uses include audio preamplification, portable instrumentation, low-level sensor conditioning, active filtering, and general-purpose analog signal conditioning. Two amplifiers in one package are especially useful for balanced differential stages, buffer stages, or paired gain blocks where matching and board-space efficiency are beneficial. Its rail-to-rail output also makes it suitable for systems whose signal range approaches the available supply voltage. When designing a circuit, verify input and output common-mode limits, output-current demand, output swing, and stability with the selected feedback network. Place input and output decoupling close to the relevant pins, route sensitive input traces away from switching nodes, and use short ground paths to minimize parasitic feedback. The 8-DIP package is convenient for prototype and legacy through-hole assemblies but requires more board area than an equivalent surface-mount package. This product page combines the TS972IN electrical characteristics, application guidance, drop-in alternatives, and design considerations needed to evaluate the amplifier for a new analog circuit. It also highlights the trade-offs among verified same-footprint alternatives without confusing package compatibility with merely similar functionality.
TS972IPT - Dual Low-Noise Rail-to-Rail Op Amp | STMicroelectronics
STMicroelectronics TS972IPT is a dual general-purpose operational amplifier with rail-to-rail output swing, 12 MHz gain-bandwidth product, 4 V/us slew rate, and operation from ±1.35 V, making it suitable for portable and battery-powered equipment. The device is packaged in an 8-pin TSSOP and is designed for instrumentation, signal conditioning, and low-voltage analog systems. Its dual-circuit configuration allows two independent amplifier channels in one package, reducing board area and simplifying power routing when both channels share the same supply voltage. The TS972 belongs to the TS97x family of low-noise operational amplifiers. An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify differences between two input voltages. The TS97x family is designed for low-voltage operation, rail-to-rail output signal swing, and portable applications where supply voltage, power consumption, and signal headroom are important design constraints. Key characteristics include a 12 MHz gain-bandwidth product, 4 V/us slew rate, dual amplifier channels, and an 8-pin TSSOP package. The rail-to-rail output stage allows the output to approach the supply rails more closely than a conventional non-rail-to-rail output stage. This is valuable in low-voltage systems where usable output range is limited and improves the effective signal range available to downstream analog and digital circuits. The TS97x family operates with voltages as low as ±1.35 V, according to STMicroelectronics product information, and the TS972IPT is identified as a 2.7 V to 10 V supply-range device in the listed technical data. The combination of low-noise operation and moderate bandwidth supports applications such as sensor interfaces, buffer stages, audio signal paths, and general-purpose analog amplification. The dual package is particularly useful when a design requires two similar channels with matching supply and ground connections. Typical uses include battery-powered instrumentation, portable measurement systems, active filtering, signal conditioning, and low-voltage sensor interfaces. The 12 MHz bandwidth provides useful speed for signals beyond static or very-low-frequency operation, while the 4 V/us slew rate helps preserve large-signal response. In designs using the rail-to-rail output, the output still requires adequate output-current capability and suitable load conditions for the selected operating point. When laying out a TS972IPT circuit, place input and output components close to their associated pins and keep sensitive input traces short and away from switching-current paths. Check the required common-mode input range, output swing, load, supply voltage, and stability conditions against the manufacturer datasheet before finalizing the application. The TSSOP package also requires careful thermal planning when both amplifier channels dissipate significant power.
TS972IQT - Dual 12MHz Low-Noise Op Amp | STMicroelectronics
The STMicroelectronics TS972IQT is a dual, general-purpose operational amplifier designed for low-noise, rail-to-rail signal processing. It provides two amplifier circuits, a 12 MHz gain-bandwidth product, and operation from 2.7 V to 10 V in an 8-pin DFN package measuring 3 x 3 mm. Its rail-to-rail output supports portable, battery-powered, instrumentation, audio, and sensor-conditioning applications where the required output can approach the supply rails. An operational amplifier is a high-gain analog building block used to amplify small voltage signals, buffer sensors, perform active filtering, and provide feedback control. The TS972 belongs to the operational-amplifier hierarchy, which includes general-purpose amplifiers, rail-to-rail input/output amplifiers, and low-noise instrumentation amplifiers. Its dual-channel configuration reduces the component count in stereo, differential, and multi-signal circuits while preserving matched performance within one package. The principal features of the TS972IQT include two amplifier channels, rail-to-rail output operation, low-noise performance suitable for audio preamplification, and a 12 MHz gain-bandwidth product. The 2.7 V minimum operating voltage makes it suitable for low-energy systems powered from a single lithium-cell range or a regulated 3.3 V rail. The small 8-DFN package also allows placement close to analog sensors, reducing sensitive-signal trace length and conserving board area. Its 12 MHz bandwidth is particularly useful when moderate-frequency closed-loop gain is required for audio buffers, active filters, and sensor interfaces. Low noise and low distortion characteristics make the amplifier appropriate for portable and battery-supplied equipment. Because the device is not limited to a high-voltage industrial rail, designers can use one amplifier family across 3 V, 3.3 V, and 5 V systems without changing the package footprint. Typical applications include microphone and line-level audio preamplification, low-voltage sensor conditioning, precision current-to-voltage conversion, active filters, and portable measurement equipment. Two independent channels can also implement differential buffering, dual-axis sensor interfaces, or stereo signal paths. The exposed-pad package can improve heat dissipation when either amplifier operates near its output-current limit, although normal signal operation generally produces modest dissipation. When laying out a board, place input and output decoupling close to the appropriate device pins and keep sensitive input traces away from switching nodes and high-current return paths. Verify the operating voltage, output swing, load, and stability requirements against the actual signal amplitude and frequency. The manufacturer datasheet should be used for the complete pin description, electrical limits, exposed-pad connection, and recommended layout. This product page combines the exact catalog identity, verified distributor references, application guidance, and drop-in replacement analysis for engineers evaluating the TS972IQT. It also identifies where an equivalent package and electrical match can be confirmed, helping design teams avoid assuming that a similar amplifier is electrically or mechanically interchangeable.
TS972IYD - Dual 12MHz Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS972IYD is a dual-circuit, general-purpose operational amplifier with rail-to-rail output swing, very low noise, and a 12 MHz gain-bandwidth product in an 8-pin SOIC package. The device supports operation from voltages as low as ±1.35 V, making it suitable for portable, battery-powered, audio, sensor, and low-voltage signal-processing equipment. An operational amplifier, or op amp, is a voltage-gain building block within analog and mixed-signal electronics. Its feedback network can create stable gain, filtering, buffering, summing, and current-control functions. The TS972IYD belongs to the operational-amplifier hierarchy, which includes rail-to-rail amplifiers, low-noise amplifiers, and low-voltage general-purpose devices used in analog signal chains. Key features of the TS972IYD include two amplifiers per package, rail-to-rail output operation, a 12 MHz gain-bandwidth product, and very low-noise characteristics. Rail-to-rail output allows the output stage to approach the supply limits, which helps maximize signal range in low-voltage systems. The dual configuration reduces board area by integrating two amplifier channels into one 8-pin SOIC package. The TS97x family operates from voltages as low as ±1.35 V and is designed for portable and battery-supplied equipment. Its combination of low-noise, low-distortion behavior, wide output swing, and moderate bandwidth supports audio preamplification, sensor conditioning, active filtering, and general analog signal processing. Engineers should account for input common-mode range, output swing, capacitive-load stability, and supply-voltage limits when selecting operating points. Typical uses include audio preamplifiers, microphone and sensor interfaces, battery-powered instrumentation, active filters, buffer stages, and low-voltage control systems. In each case, the dual channel arrangement can support paired signal paths or provide an unused amplifier for filtering, level shifting, or test functions while keeping the footprint compact. For a new layout, route the bypass capacitor directly to the supply and ground pins, keep feedback traces short, and verify stability with the intended source impedance and load. Component substitutions require confirmation of the SOIC footprint, pin functions, supply range, common-mode behavior, output swing, bandwidth, and noise performance rather than package similarity alone. This product page combines the device identity, package information, documented operating characteristics, sourcing workflow, and engineering guidance. It also distinguishes confirmed TS97x-family options from unsupported substitute claims and focuses replacement analysis on genuine pin-compatible, same-package possibilities rather than merely similar amplifier functions.
TS974ID - 12 MHz Low-Noise Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS974ID is a quad operational amplifier with four rail-to-rail output stages, 12 MHz gain-bandwidth product, 4 V/µs slew rate, and 4 nV/√Hz noise density in a 14-pin SOIC package. It operates from 2.7 V to 10 V, including split-supply operation as low as ±1.35 V, and is intended for portable, battery-powered, audio, sensor, and general-purpose signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify small voltage signals. The TS974ID belongs to the TS97x family of low-noise, low-distortion amplifiers. Within the broader semiconductor hierarchy, an operational amplifier is an analog amplifier IC, a linear signal-processing component, and ultimately part of a power-management and signal-chain ecosystem. Its four amplifiers combine rail-to-rail output swing with a 12 MHz bandwidth and 4 V/µs slew rate. The stated 4 nV/√Hz noise density supports low-noise signal acquisition, while the specified 0.003% distortion improves linearity in audio and precision analog circuits. A supply range of 2.7 V to 10 V permits operation from a single 3.3 V or 5 V rail or from a split supply as low as ±1.35 V. The TS97x architecture is designed for low-noise and low-distortion performance, with particular suitability for portable and battery-supplied equipment. The quad configuration provides four amplifiers in one 14-pin SOIC package, reducing board area when multiple analog channels require similar electrical performance. Its 12 MHz bandwidth is substantially higher than that required for many slow sensor-conditioning channels, allowing designers to preserve signal fidelity over a wider frequency range. Typical applications include audio preamplification, microphone and sensor conditioning, portable instrumentation, active filtering, data acquisition, and low-voltage embedded systems. The TS974ID is especially useful when several channels must process signals without adding a separate amplifier package for every stage. In audio systems, its low noise and low distortion support cleaner preamplifier operation; in sensors, the rail-to-rail output can improve usable dynamic range on low-voltage supplies. When designing around the TS974ID, account for input common-mode range, output swing, stability with the selected feedback network, and noise bandwidth. Decoupling capacitors should be placed close to the supply pins, while analog input and feedback paths should be kept short and away from switching nodes. Stable feedback components and suitable output loading are important when exploiting the device's 12 MHz bandwidth. This product record consolidates verified manufacturer-family characteristics, distributor availability, package information, and practical application guidance. It also identifies the missing pricing, pin-level, environmental, and qualification details explicitly rather than estimating them, allowing engineers to compare the TS974ID against other low-noise rail-to-rail quad amplifiers before committing to a design.
TS974IDT - 12 MHz Quad Rail-to-Rail Op Amp | ST
The STMicroelectronics TS974IDT is a four-circuit rail-to-rail operational amplifier featuring a 12 MHz gain-bandwidth product, 4 V/us slew rate, and 4 nV/Hz noise density in a 14-pin SO package. Its rail-to-rail output swing and operating capability from voltages as low as ±1.35 V make it suitable for compact analog signal chains that require low noise, high dynamic performance, and flexible supply-voltage operation. An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify voltage differences. The TS974 belongs to the operational-amplifier hierarchy, which sits within amplifier ICs and analog signal-processing semiconductors. Rail-to-rail output operation allows the output to approach the available supply rails, while low-noise amplification preserves small signals in audio, instrumentation, sensor, and control systems. The TS974IDT combines four amplifiers in one package. Key characteristics include 4 nV/Hz noise density, 0.003% distortion, 12 MHz bandwidth, and 4 V/us slew rate. These figures support high-frequency signal amplification with relatively low added noise. The device also includes 2 kV ESD protection and Class A latch-up immunity, improving practical robustness in sensitive analog applications. Its architecture is optimized for low-noise and low-distortion operation. The 12 MHz bandwidth provides adequate response for audio preamplification and general instrumentation, while the 4 V/us slew rate helps preserve large-signal fidelity. The rail-to-rail output topology reduces output-voltage headroom concerns, although designers must still evaluate input common-mode range, output swing, supply voltage, stability, and output loading against the manufacturer specifications. Typical uses include low-noise audio preamplification, portable and battery-powered instrumentation, sensor signal conditioning, industrial measurement systems, and general-purpose analog signal processing. The four-amplifier configuration reduces board area when several independent channels are required. It is particularly useful where four similar low-noise channels must operate within one compact package. Designers should place input and output compensation or decoupling components according to the recommended application circuit, maintain the required input and output common-mode range, and verify stability with the intended source and load impedances. The low-noise performance does not remove the need for careful grounding, short PCB traces, and clean supply routing. This page combines the principal TS974IDT operating characteristics, practical application guidance, package information, and verified replacement relationships. It also highlights design constraints and selection trade-offs that help engineers determine whether the device is appropriate before committing it to a new PCB layout.
TS974IN - 4-Channel Low-Noise Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS974IN is a four-circuit, rail-to-rail operational amplifier with a very low noise density of 4 nV/Hz, a 12 MHz gain-bandwidth product, and a 4 V/us slew rate, packaged in a 14-pin DIP. It is designed for applications that require low-noise signal amplification across multiple independent channels. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Within the amplifier hierarchy, the TS974IN is a general-purpose precision operational amplifier and a member of the rail-to-rail low-noise amplifier family. Rail-to-rail input and output operation allows the signal to approach the supply rails, improving usable dynamic range in low-voltage and single-supply systems. The TS974IN provides four amplifier channels in one package, reducing board area and simplifying multi-channel signal-conditioning layouts. Its 4 nV/Hz noise density supports high-resolution analog measurement, while the 12 MHz gain-bandwidth product and 4 V/us slew rate preserve signal fidelity in faster signal paths. The listed ultra-low distortion of 0.003% makes the device suitable for audio preamplification, filtering, buffering, and instrumentation. The device operates over a supply range extending to 10 V and includes ESD protection rated at 2 kV. The listed latch-up immunity is Class A. Each amplifier is configured as a standard voltage-feedback operational amplifier, allowing the same component to implement inverting, non-inverting, summing, comparator-style, and active-filter circuits. Operating and electrical limits should always be confirmed in the manufacturer datasheet. Typical uses include four-channel audio preamplification, sensor signal conditioning, active audio filters, low-level instrumentation, data acquisition front ends, and general-purpose analog buffering. Because all four channels share one package, matching and thermal tracking are convenient when several related analog signals are processed under similar conditions. For low-noise layouts, keep the input and feedback resistors short, place input compensation and decoupling capacitors close to the relevant pins, and avoid routing high-impedance input traces beside digital clock or switching nodes. Select the bypass capacitance and compensation values with the datasheet's stability and noise guidance in mind, particularly when driving capacitive loads. This page combines the verified TS974IN product characteristics with application guidance, drop-in replacement analysis, and engineering design notes. It is intended to help designers evaluate the TS974IN quickly while completing the mandatory signal-integrity, noise, and stability checks against the full manufacturer documentation.
TS974IYD - 12MHz Quad Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TS974IYD is a four-circuit, general-purpose operational amplifier with rail-to-rail output swing, 12 MHz gain-bandwidth product, 60 dB common-mode rejection, and a 14-SOIC package. It accepts a 2.7 V to 10 V single-supply range or dual-supply operation from ±1.35 V to ±5 V, with a nominal 5 V single-supply configuration identified for the device. An operational amplifier is an analog signal-conditioning IC that compares an input voltage with a feedback-defined reference and amplifies the resulting error voltage. The TS974 belongs to the rail-to-rail operational amplifier hierarchy, where the output can approach the supply rails. This characteristic is useful when the available signal range is small, while its low-noise and low-distortion behavior make the TS97x family suitable for audio preamplification and portable instrumentation. The TS974IYD combines four amplifiers in one 14-SOIC package. Each channel has a gain-bandwidth product of 12 MHz and supports up to 100 mA of output current. Its 60 dB common-mode rejection ratio improves immunity to common-mode voltage on the input pair, while the 200 nA input bias current and 1 µA quiescent current per channel suit low-power circuitry. These characteristics support portable and battery-powered equipment operating from low supply voltages. The device supports both single- and dual-supply arrangements. In a single-supply system, the input and output signal range requires attention near the rails even though the output stage has rail-to-rail swing. In a dual-supply circuit, the stated operating range extends from ±1.35 V to ±5 V. Because the TS974 is intended for low-noise amplification, resistor selection, decoupling, grounding, and output-load compatibility remain central to achieving the intended signal quality. Typical uses include portable audio preamplification, low-level sensor conditioning, battery-powered measurement equipment, active filters, and general-purpose analog signal processing. Four channels in one package also reduce board area when a system needs several similar gain stages. The package pin arrangement and electrical characteristics must be checked against the manufacturer datasheet before applying it to a new board or using it as a replacement. For a new design, begin with the required signal bandwidth, output swing, supply voltage, and load current. Place the bypass capacitor near the power pins, keep feedback loops compact, and verify that input common-mode and output swing requirements remain valid at the chosen gain. For an existing PCB, confirm the 14-SOIC footprint, pin functions, and electrical limits before substituting another amplifier. This page consolidates the available manufacturer-family information, distributor listing details, ordering guidance, and drop-in comparison considerations. It is designed to help engineers identify whether the TS974IYD fits a low-voltage, low-noise quad-op-amp design before moving to detailed circuit review and datasheet verification.
TS982IDW - Dual 200mA R-R Op Amp | STMicroelectronics
STMicroelectronics TS982IDW is a dual operational amplifier with rail-to-rail output capability, 200 mA output-current drive, and operation from voltages as low as 2.7 V. The device is housed in an 8-pin SO package and is stable at unity gain. Its combination of low supply voltage, broad output-current capability, and dual-channel integration makes it suitable for industrial and automotive signal-conditioning systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TS982 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its dual architecture provides two amplifier channels in one package, reducing component count when a board needs matched signal conditioning, buffering, or gain stages. The TS982's rail-to-rail output stage can approach the supply rails, increasing usable output-voltage range in low-voltage systems. Its ability to drive 200 mA makes it stronger than many general-purpose dual amplifiers and allows the device to feed higher-capacitance loads or drive downstream stages. Operation down to 2.7 V supports modern low-power electronics, while unity-gain stability simplifies buffer and fixed-gain implementations. The SO-8 package provides a compact footprint for industrial, automotive, and embedded systems. The exposed-pad construction supports heat transfer when the amplifier operates at elevated output current, although board layout and thermal design remain important. Two amplifiers in one package also simplify dual-channel designs where both channels perform related functions. Typical uses include sensor-signal conditioning, active filtering, audio and communications interfaces, data acquisition, and general-purpose analog buffers. The 200 mA drive capability is particularly useful when the op-amp must charge a downstream capacitance, interface with another analog circuit, or support a load beyond the range of a lightweight low-power amplifier. Designers should verify the exact input common-mode range, output swing, bandwidth, slew rate, noise, offset, and thermal limits for the operating conditions. Input and output stability must be evaluated with the intended feedback network and load because capacitive loading can affect op-amp behavior even when unity-gain stable. This page combines manufacturer-device facts, package details, sourcing guidance, and practical analog-design considerations to help engineers evaluate TS982IDW for low-voltage, dual-channel signal-processing designs.
TSV524IQ4T - Quad 1.15MHz CMOS Op-Amp, RRIO | STMicroelectronics
The STMicroelectronics TSV524IQ4T is a quad CMOS operational amplifier that delivers a 1.15 MHz gain-bandwidth product while consuming only 45 µA per channel at 5 V, in a 16-pin QFN (3x3) package. It operates from a single 2.7 V to 5.5 V supply with rail-to-rail input and output (RRIO) swing, and offers a slew rate of 0.89 V/µs with an input bias current of just 1 pA and a typical input offset voltage of 1 mV. What is a CMOS operational amplifier? A CMOS op-amp is a type of analog integrated circuit that uses complementary metal-oxide-semiconductor transistors in its input and gain stages. Compared to bipolar op-amps, CMOS op-amps typically offer higher input impedance, lower input bias current, and lower quiescent power consumption, making them well-suited for battery-powered and high-impedance sensor interfaces. The TSV524IQ4T sits in the broader taxonomy: operational amplifier -> amplifier IC -> analog IC -> semiconductor. Its RRIO capability means the output can swing within millivolts of both supply rails, maximizing dynamic range in low-voltage single-supply systems. Key features include the high merit factor (1.15 MHz GBW for only 45 µA supply current), 1 pA typical input bias current that simplifies high-impedance sensor signal chains, 100 pF capacitive load drive capability, and the tiny 3x3 mm QFN-16 footprint that enables dense multi-channel designs. An exposed pad (EP) on the package provides a low thermal-resistance path to the PCB, useful when several channels drive continuous loads. Architecturally, the TSV524IQ4T uses a CMOS input stage with rail-to-rail input common-mode range achieved through complementary N/P differential pairs. The output stage is a class-AB CMOS topology that delivers rail-to-rail output swing. This design optimizes the speed-to-power ratio for applications where low quiescent current matters more than raw bandwidth. Typical applications include battery-powered sensor signal conditioning, portable instrumentation, active filters, transducer interfaces, and current-sensing amplifiers. The wide supply range and RRIO capability make it a strong fit for single-cell Li-ion (3.0-4.2 V) and 3.3 V system designs. When designing with this device, note that the QFN-16 package requires careful PCB layout - the exposed thermal pad must be soldered to a sufficiently large copper area to meet the published thermal resistance and to maintain mechanical reliability. Decouple each supply pin with a 100 nF ceramic capacitor placed as close to the IC as possible. This page synthesizes distributor pricing, verified pin-to-pin drop-in alternatives, and PCB/thermal design guidance for the TSV524IQ4T that complements the manufacturer datasheet.
TSV991ILT - 20MHz Rail-to-Rail Op Amp | STMicroelectronics
The STMicroelectronics TSV991ILT is a single, high-speed, rail-to-rail input/output operational amplifier offering a gain-bandwidth product of 20 MHz and a slew rate of 10 V/µs. It operates from a supply voltage range of 2.5 V to 5.5 V, making it suitable for battery-powered and low-voltage applications. The device is available in the compact SOT-23-5 package, ideal for space-constrained designs. An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in signal conditioning, filtering, and amplification. The TSV991ILT belongs to the family of general-purpose op-amps, which are characterized by their versatility and ease of use. In the hierarchy of analog components, op-amps are part of the broader category of linear integrated circuits, which also includes comparators and voltage regulators. Key features of the TSV991ILT include rail-to-rail input and output stages, which maximize the dynamic range in low-voltage applications. The device also features a low input offset voltage of 1.5 mV (max) and a low input bias current of 1 pA (typ), ensuring high accuracy in precision circuits. The 20 MHz bandwidth and 10 V/µs slew rate enable the amplifier to handle high-frequency signals, making it suitable for video and communication applications. The TSV991ILT is built on STMicroelectronics' advanced BiCMOS process, which combines the benefits of bipolar and CMOS technologies. This process achieves a good balance between speed, power consumption, and noise performance. The amplifier's quiescent current is typically 1.1 mA, providing a favorable trade-off between speed and power efficiency for battery-operated devices. Typical applications include active filters, signal conditioning, portable instrumentation, and audio processing. The rail-to-rail output capability allows the amplifier to drive ADC inputs directly, maximizing the usable input range. In sensor interfaces, the low input bias current minimizes errors when interfacing with high-impedance sensors. When designing with the TSV991ILT, ensure proper power supply decoupling with a 0.1 µF ceramic capacitor placed close to the VCC pin. The input common-mode voltage range extends beyond the supply rails, but care should be taken to avoid exceeding the absolute maximum ratings. The output can swing within 50 mV of the rails, which is beneficial for single-supply operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing a comprehensive resource for engineers evaluating the TSV991ILT.
TSX9292IST - 16MHz RR 16V CMOS Op-Amp, Dual | STMicroelectronics
The STMicroelectronics TSX9292IST is a dual operational amplifier featuring 16 MHz gain-bandwidth product, 27 V/µs slew rate, and 0.0003 % THD+N, housed in an 8-pin MiniSO (Mini Small Outline) package. It operates from a single 4 V to 16 V supply and provides rail-to-rail input and output swing, making it suitable for low-voltage, single-supply, and high-fidelity signal-chain designs. The two on-chip amplifiers are decompensated and stable for gains greater than +2 (or inverting gains less than -1), and each channel draws a typical 2.8 mA quiescent current. A CMOS operational amplifier (op-amp) is a high-gain DC-coupled differential amplifier built on a CMOS process. In a system hierarchy it sits under amplifier ICs -> analog front-end -> signal conditioning -> mixed-signal subsystem. The 'rail-to-rail' designation means the input common-mode range and the output swing can approach both supply rails, which maximizes dynamic range in low-voltage designs - critical when the supply is only 5 V or 3.3 V and every millivolt of headroom counts. Key features include 16 MHz GBP, 27 V/µs slew rate, 0.0003 % THD+N (Total Harmonic Distortion plus Noise), low input bias current from CMOS input stages, and 2.8 mA per-channel quiescent current. The TSX92x family is a pin-compatible upgrade path for legacy TS912/TS914 designs requiring higher AC performance with the same supply range and MiniSO/SO footprint options. The TSX9292IST uses a CMOS input stage that delivers very low input bias current, paired with a class-AB rail-to-rail output stage that swings within tens of millivolts of either rail. The 'IST' suffix denotes the MiniSO-8 (TSSOP-equivalent micro-package) tape-and-reel option, optimized for compact surface-mount layouts. Stability requires a minimum closed-loop gain of 2, meaning the part is not unity-gain stable - it must be used with sufficient gain to maintain phase margin. Typical applications include active filters, audio line drivers and headphone amplifiers, transducer conditioners, motor-control sense amplifiers, and industrial sensor interfaces. The wide supply range (4 V-16 V) makes it equally comfortable in 5 V industrial loops, 12 V automotive subsystems, and ±5 V split-rail instrumentation. When designing with this device, always configure the circuit for closed-loop gain ≥ +2 (or inverting gain ≤ -1) to guarantee stability. Add a small series output resistor (~10-50 Ω) when driving large capacitive loads to prevent peaking, and place a 0.1 µF decoupling capacitor close to each supply pin. Verify output current limits at high supply voltages, as the CMOS output stage can only source or sink tens of milliamps to stay in the linear region. This page synthesizes distributor pricing, drop-in alternative recommendations, and practical design considerations not consolidated on the manufacturer datasheet, with source attribution for every claim.
WM9001GEFL - 1W Class AB/D Speaker Driver | Cirrus Logic
The Cirrus Logic WM9001GEFL is a 1 W mono dual-mode Class AB and Class D speaker driver packaged in a 16-pin QFN with an exposed pad. The distributor data identifies it as an audio amplifier IC with a 1 W output rating, Class AB and Class D operating modes, and a compact 3 x 3 mm QFN package. These characteristics place it in the speaker-driver hierarchy of audio amplifier ICs used to drive small electrodynamic transducers. A speaker-driver amplifier is an integrated circuit that accepts an analog audio signal and delivers enough current and voltage to move a miniature speaker cone. The dual-mode architecture gives a system designer the option to select Class AB behavior for linear output or Class D behavior for higher conversion efficiency. The WM9001GEFL is therefore positioned for compact audio products where speaker output, board area, and energy consumption must be balanced. The WM9001GEFL's principal verified specifications are its 1 W output capability, single-channel mono configuration, support for both Class AB and Class D amplification, and 16-QFN package with an exposed pad. The exposed pad supports heat transfer from the IC into the printed circuit board. Because no verified voltage, current, frequency-response, distortion, thermal-resistance, or shutdown information was supplied, those values must be confirmed in the manufacturer datasheet before final design release. Technically, this device belongs to the integrated-circuit amplifier family and more specifically to speaker-driver audio ICs. Its 3 x 3 mm QFN package supports high-density PCB layouts but demands careful control of exposed-pad soldering, copper thermal paths, and acoustic-mechanical layout. Class AB and Class D modes can also differ in EMI behavior and power efficiency, so mode selection should be based on the complete analog path, speaker impedance, and enclosure conditions rather than package size alone. Typical uses include portable-device speakers, compact consumer-audio products, personal-audio accessories, small embedded audio systems, and accessory modules requiring a mono 1 W drive stage. In these applications, the device can sit near the speaker connector to shorten the high-current output path, reduce load-related board losses, and simplify the analog architecture. Designers should still validate output power at the intended speaker impedance and frequency range. The primary design consideration is thermal management. Although the package includes an exposed pad, continuous Class AB output near the 1 W rating can dissipate more power than Class D operation. The pad should be connected to a suitable ground plane and thermal copper area, while input, feedback, and output routing should avoid the loudspeaker return path. Decoupling and output-filter values must come from the manufacturer application guidance. This product record consolidates verified distributor inventory, package information, source links, engineering caveats, and selection guidance that are not consolidated on a typical distributor listing. Where the supplied evidence does not establish a parameter or a true pin-compatible substitute, the record explicitly marks the gap rather than presenting an unsupported value.
WM9001GEFL/R - 1W Class AB/D Speaker Driver | Cirrus Logic (Tape & Reel)
The Cirrus Logic WM9001GEFL/R is a 1 W mono dual-mode Class AB and Class D speaker driver packaged in a 16-pin QFN with an exposed pad. The distributor data identifies it as an audio amplifier IC with a 1 W output rating, Class AB and Class D operating modes, and a compact 3 x 3 mm QFN package. These characteristics place it in the speaker-driver hierarchy of audio amplifier ICs used to drive small electrodynamic transducers. A speaker-driver amplifier is an integrated circuit that accepts an analog audio signal and delivers enough current and voltage to move a miniature speaker cone. The dual-mode architecture gives a system designer the option to select Class AB behavior for linear output or Class D behavior for higher conversion efficiency. The WM9001GEFL/R is therefore positioned for compact audio products where speaker output, board area, and energy consumption must be balanced. The WM9001GEFL/R's principal verified specifications are its 1 W output capability, single-channel mono configuration, support for both Class AB and Class D amplification, and 16-QFN package with an exposed pad. The exposed pad supports heat transfer from the IC into the printed circuit board. Because no verified voltage, current, frequency-response, distortion, thermal-resistance, or shutdown information was supplied, those values must be confirmed in the manufacturer datasheet before final design release. Technically, this device belongs to the integrated-circuit amplifier family and more specifically to speaker-driver audio ICs. Its 3 x 3 mm QFN package supports high-density PCB layouts but demands careful control of exposed-pad soldering, copper thermal paths, and acoustic-mechanical layout. Class AB and Class D modes can also differ in EMI behavior and power efficiency, so mode selection should be based on the complete analog path, speaker impedance, and enclosure conditions rather than package size alone. Typical uses include portable-device speakers, compact consumer-audio products, personal-audio accessories, small embedded audio systems, and accessory modules requiring a mono 1 W drive stage. In these applications, the device can sit near the speaker connector to shorten the high-current output path, reduce load-related board losses, and simplify the analog architecture. Designers should still validate output power at the intended speaker impedance and frequency range. The primary design consideration is thermal management. Although the package includes an exposed pad, continuous Class AB output near the 1 W rating can dissipate more power than Class D operation. The pad should be connected to a suitable ground plane and thermal copper area, while input, feedback, and output routing should avoid the loudspeaker return path. Decoupling and output-filter values must come from the manufacturer application guidance. This product record consolidates verified distributor inventory, package information, source links, engineering caveats, and selection guidance that are not consolidated on a typical distributor listing. Where the supplied evidence does not establish a parameter or a true pin-compatible substitute, the record explicitly marks the gap rather than presenting an unsupported value.
WM9010ECSN/R - Class G Stereo Driver | Cirrus Logic
Cirrus Logic WM9010ECSN/R is a low-power, two-channel Class G stereo headphone-driver IC rated at 12 W in a 12-W-CSP package measuring 1.84 x 1.34 mm. The device supports a 16 ohm headphone load and achieves THD+N of -90 dB at 20 mW into 32 ohm with a 1.8 V supply. Its integrated charge pump generates split-rail voltage supplies for the ground-referenced headphone output stage. A Class G headphone amplifier is an audio amplifier architecture that combines signal-dependent output characteristics with efficient power delivery. Unlike a continuously biased linear output stage, Class G changes its internal supply behavior according to signal level and load demand. In a portable headset or portable media device, this approach helps reduce power consumed during quiet passages while retaining the output capability needed for louder playback. The WM9010ECSN/R belongs to the broader audio-amplifier IC and power-management semiconductor hierarchy. The WM9010ECSN/R provides a stereo output configuration, Class G efficiency, and an integrated charge pump in a compact surface-mount package. Its 12-lead CSP is only 1.84 x 1.34 x 0.7 mm, making it suitable for space-constrained portable equipment. A listed output-power figure of 34 mW applies to the characterized operating condition, while the distributor package classification identifies the device as a 12 W-class headphone driver. Headphone impedance and supply voltage remain important when evaluating available output power and distortion. Audio performance depends on the selected load and operating point. The manufacturer specification of THD+N at -90 dB, 20 mW output, 32 ohm load, and 1.8 V supply demonstrates low distortion at a practical portable-audio level. The integrated charge pump produces the positive and negative rail voltages needed by the ground-referenced headphone driver, reducing the number of external negative-supply components while adding charge-pump switching considerations to PCB layout. Typical applications include wired and wireless headphones, Bluetooth headset audio paths, portable game accessories, compact USB-C audio devices, and battery-powered music players. The small 12-W-CSP footprint supports dense layouts, while the 16 ohm load specification directly addresses conventional stereo-headphone impedances. In each application, the headphone source should be AC-coupled as required by the circuit design, and the power supply must remain within the device's specified operating limits. The most important design consideration is PCB implementation around a compact CSP with an integrated charge pump. Place input, output, supply, and decoupling connections according to the manufacturer layout guidance, keep the charge-pump and sensitive audio paths physically separated, and provide a quiet ground return. Confirm output-power capability at the actual supply voltage, channel load, and headphone impedance rather than relying only on the headline package classification. This product page combines the WM9010ECSN/R electrical characteristics, package data, drop-in-replacement review, application guidance, and design notes into a concise engineering reference. It is intended to accelerate schematic planning, footprint verification, and audio-path design without replacing the complete manufacturer datasheet.
WM9082ECSN/R - 3W Mono PDM Class D Driver | Cirrus Logic
The Cirrus Logic WM9082ECSN/R is a 3 W mono Class D speaker-driver IC with a PDM audio input, housed in a 9-ball W-CSP package measuring 1.57 mm by 1.47 mm. The device is intended for compact systems that receive digital audio directly from a PDM-compatible source, avoiding a separate analog audio input stage. Its Class D output architecture supports efficient speaker drive, while the small package supports space-constrained portable products. A Class D audio amplifier is a switching power amplifier that converts a digital or analog audio signal into a pulse-width-modulated output. The switching elements deliver energy to the speaker rather than dissipating the entire audio waveform as linear amplifiers do. A PDM input, also called pulse-density modulation, represents audio samples as a one-bit stream whose density changes over time. In the signal chain, the WM9082 belongs to the audio amplifier hierarchy and converts a PDM source into a mono Class D speaker output. The WM9082ECSN/R provides a single mono output channel and is identified as a 3 W Class D speaker driver. Its operating characteristics include PDM input support and automatic output enablement when PDM audio data is detected or when a valid Start-Up Control Code is received. These functions are useful in portable and embedded audio products because they allow the amplifier to remain inactive until valid audio activity is present, helping reduce unnecessary system activity. The compact 9-W-CSP construction is suitable for wearables, portable speakers, smart-home accessories, and compact consumer electronics where board area is limited. Because the package has a small thermal and electrical footprint, careful PCB layout is important. The speaker output, ground connection, PDM clock and data lines, supply connections, and any external filtering components should follow the manufacturer reference layout and recommended component values. This page emphasizes the distinctions that matter during schematic capture, PCB implementation, and sourcing. The WM9082 is most appropriate when the host processor or codec already supplies PDM audio and the system needs a compact mono speaker stage. It is less suitable for designs requiring conventional analog line input, multiple output channels, or a larger specified output-power level without reviewing the complete datasheet limits. The available listings also describe the device as a Cirrus Logic mono Class D audio amplifier, while the underlying datasheet identifies the original manufacturer as Wolfson Microelectronics. Use the manufacturer datasheet for the definitive electrical limits, recommended application circuit, pin description, exposed-ball configuration, and startup-code behavior. In particular, verify the allowed supply range, output-power conditions, speaker impedance, decoupling requirements, clocking limits, and PCB land pattern before release. The 1.57 mm by 1.47 mm package also makes assembly capability and land-pattern validation important during hardware planning. This page organizes the key WM9082ECSN/R specifications, sourcing information, application guidance, and replacement constraints in one place. It also distinguishes confirmed drop-in substitutions from broadly similar Class D drivers, helping engineers avoid choosing a device merely because its output wattage appears similar but whose package, pinout, input architecture, or control interface differs.
WM9094ECS/R - 2W Mono Class D/AB Amplifier | Cirrus Logic
Cirrus Logic WM9094ECS/R is a 1-channel mono audio amplifier IC delivering up to 2 W into a 4-ohm load, with both Class D and Class AB operation in a 20-WCSP package measuring 2.53 mm by 2.07 mm. The device operates from a 2.7 V to 5.5 V supply and is intended for compact low-power audio systems. An audio amplifier is an integrated circuit that converts an input audio signal into sufficient output power to drive a loudspeaker or other transducer. Class AB amplifiers provide linear operation with comparatively continuous output current, while Class D amplifiers switch the output stage to improve power-conversion efficiency. The WM9094ECS/R supports both operating modes, giving designers flexibility according to their efficiency, distortion, and thermal requirements. Key features include Class D and Class AB output capability, a 2 W maximum output-power rating into 4 ohms, integrated depop circuitry, integrated thermal protection, and a surface-mount 20-WCSP package. The 2.7 V minimum supply voltage supports portable and space-constrained equipment, while the 5.5 V maximum supply voltage accommodates common low-voltage power rails. The WM9094ECS/R is identified as a mono, one-channel amplifier rather than a multi-channel power amplifier. Its compact 2.53 mm by 2.07 mm package can reduce board area in mobile accessories, personal-audio products, and other integrated audio equipment. The manufacturer and distributor listings identify it as an ultra-low-power audio subsystem and list the part as obsolete. Typical applications include compact speaker systems, portable audio accessories, and low-voltage embedded products where a single amplified channel is sufficient. System-level implementation must account for the 2.7 V to 5.5 V supply range, speaker impedance, output power, thermal conditions, and the small-area land-pattern requirements of the 20-WCSP package. The principal design consideration is the obsolete lifecycle status. Designers should verify availability, source quality, and long-term supply before committing to a new production design. For a new design with obsolete risk, engineers may need to qualify an alternative rather than assume that any Class D or Class AB amplifier is pin compatible. This page consolidates the verified distributor specifications, lifecycle information, package details, sourcing links, practical application guidance, and an explicit assessment of replacement availability. It also separates documented parameters from missing technical data instead of presenting unverified electrical characteristics as guaranteed specifications.