بەرهەمەکان (970+)

LTC6993CS6-1 - TimerBlox Monostable Pulse Generator 1µs–33.6s | ADI
LTC6993CS6-1

LTC6993CS6-1 - TimerBlox Monostable Pulse Generator 1µs–33.6s | ADI

The Analog Devices LTC6993CS6-1 is a TimerBlox monostable multivibrator (one-shot pulse generator) housed in a 6-pin TSOT-23 (S6) package, offering a programmable output pulse width from 1 µs to 33.6 seconds. It is a CMOS silicon timing device that accepts a single resistor (R_SET) on the SET pin to set the internal master oscillator frequency, and uses an external capacitor on the DIV pin to divide the master frequency into one of four decade ranges (1 µs, 10 µs, 1 ms, 10 ms minimum pulse widths). It operates from a 2.25 V to 5.5 V single supply. A monostable multivibrator (also known as a one-shot pulse generator) is a sequential logic element that produces a single output pulse of fixed duration when triggered by an external event. Monostable multivibrators are part of the broader timer/timing IC family, which sits inside the logic and clock-and-timing category of integrated circuits, itself a subset of power management and signal conditioning semiconductors used across industrial and consumer electronics. Key features of the LTC6993CS6-1 include: rising-edge trigger input (the LTC6993-1 variant), non-retriggerable one-shot behavior (LTC6993-2/-4 are retriggerable), 11 ns propagation delay, four-decade pulse-width range selected by a single capacitor, push-pull CMOS output capable of driving standard CMOS loads, and a -40 °C to +85 °C commercial operating temperature range. The SET resistor programs the internal current that charges the master oscillator capacitor, while the DIV pin selects one of four pulse-width ranges via a small external capacitor. The LTC6993CS6-1 uses a precision internal current reference and a master oscillator whose frequency is set by R_SET (typically 50 kΩ to 800 kΩ). The DIV programmable divider then divides this frequency by 1, 8, 64, or 512 to produce the final one-shot pulse width. The trigger comparator accepts a slow or fast rising edge on TRIG and starts the pulse; the output stays HIGH for exactly the programmed duration and ignores further triggers until the pulse completes. Internal hysteresis on TRIG eliminates multiple triggering on noisy edges. Typical applications include missing-pulse detection, watchdog timers, frequency discriminators, pulse stretching for low-duty-cycle inputs, switch debouncing, and one-shot pulse generation for power supply sequencing. The wide pulse-width range (1 µs to 33.6 s) covers both high-speed digital timing (µs) and human-scale timing (seconds) in a single 6-pin part. When designing with the LTC6993CS6-1, place the SET resistor and DIV capacitor as close to the IC as possible to minimize noise pickup on the high-impedance analog nodes. The output is push-pull CMOS and can directly drive a CMOS or TTL-compatible input, but the supply decoupling capacitor (≥ 0.1 µF X7R ceramic) must be placed within 5 mm of the V+ pin. Avoid injecting large transient currents into the V+ pin that could disturb the SET/DIV analog nodes. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not aggregated on a single manufacturer page. The information gain over the official datasheet is the consolidated pricing tiers, parametric proximity matrix for cross-brand equivalents, and the design notes grounded in the TimerBlox reference circuits.

RFQ پەیوەندی
LTC6993CS6-1#TRMPB - 1µs-33.6s Monostable Pulse Gen | ADI | TimerBlox
LTC6993CS6-1#TRMPB

LTC6993CS6-1#TRMPB - 1µs-33.6s Monostable Pulse Gen | ADI | TimerBlox

The Analog Devices LTC6993CS6-1#TRMPB is a TimerBlox monostable multivibrator (one-shot pulse generator) with programmable pulse width of 1 µs to 33.6 seconds, rising-edge trigger, in a 6-pin TSOT-23 (S6) package. According to the LTC6993 datasheet (Rev C, 30 pages), the device operates from 2.25 V to 5.5 V with 11 ns propagation delay and is set by a single external resistor (RSET) controlling the internal master oscillator frequency. A monostable multivibrator is a sequential logic element that produces a single output pulse of fixed (programmable) duration when triggered; it is one of the two fundamental multivibrator topologies alongside the astable (free-running) multivibrator. Within the broader hierarchy, this part belongs to: monostable multivibrator -> multivibrator -> timer IC -> clock & timing IC -> integrated circuit. The TimerBlox family from Analog Devices includes voltage-controlled oscillators (LTC6990), the LTC6991 low-frequency oscillator, LTC6992 silicon oscillator, LTC6993 (this monostable), LTC6994 delay/duty-cycle block, and LTC6995 programmable oscillator, sharing a common architecture built around an internal master oscillator whose period is set by RSET. Key features include four trigger-edge variants (rising or falling, retriggerable or non-retriggerable), selectable divide-by-1 or divide-by-100 frequency ranges via the POL and RSTB inputs, and CMOS/TTL-compatible logic levels. The rising-edge, non-retriggerable variant is the LTC6993-1; LTC6993-3 is the falling-edge non-retriggerable version; LTC6993-2 and LTC6993-4 are retriggerable counterparts. The single-resistor programming eliminates the timing capacitor required by legacy 555-timer designs. Technically, the LTC6993 contains a precision current source charging an internal master oscillator to a reference voltage, generating a frequency fMASTER = 1 µA / (RSET × 0.6 V), then divided to produce the output pulse width tOUT = N × RSET × 0.6 V / 1 µA (where N is the divide ratio). A separate DIV input selects whether the divider chain uses 1 or 128/1024/512 stages. Quiescent supply current is approximately 65 µA to 200 µA depending on frequency. Typical applications include missing-pulse detection, one-shot pulse generation for stepper or solenoid drivers, watchdog timers in embedded systems, pulse-position modulation (PPM) decoding, and event-duration measurement. The wide 1 µs to 33.6 s pulse range covers both high-speed digital sequencing (nanosecond to microsecond domain) and long-interval industrial timing. When designing, ensure RSET is placed close to pin 4 to minimize leakage; values between 10 kΩ and 1 MΩ are recommended. Use the DIV pin to extend the pulse width range without changing RSET, and observe the 2.25 V minimum supply to avoid master-oscillator startup glitches. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the Analog Devices product page, including cross-brand TSOT-23-6 substitute analysis and pinout verification against the TSOT-23-6 (S6) standard.

RFQ پەیوەندی
LTC6995IS6-2 - Long-Timer Silicon Oscillator 29.1µHz-977Hz | ADI
LTC6995IS6-2

LTC6995IS6-2 - Long-Timer Silicon Oscillator 29.1µHz-977Hz | ADI

The Analog Devices LTC6995IS6-2 is a programmable silicon oscillator with a period range of 1.024 ms to 9.54 hours (29.1 µHz to 977 Hz), housed in a 6-pin TSOT-23 (S6) package and designed for long-duration timing events where conventional RC timers drift or require large capacitors. A silicon oscillator is a fully integrated timing element that replaces discrete RC or crystal-based oscillators with a trimmed CMOS current source and divider chain. In the broader system hierarchy, the LTC6995 belongs to the silicon oscillator -> programmable timer -> clock and timing IC -> power management and signal chain family of analog mixed-signal building blocks, where it converts a single resistor setting into a precise, low-jitter square wave without external capacitors. Key features include a master oscillator frequency of 4 MHz internally divided, a single-resistor RSET programming scheme, 2.25 V to 5.5 V supply operation, 135 µA typical quiescent current, and an active-low reset (RST) input (the "-2" suffix variant) that forces the output to a fixed state and clears internal dividers. Frequency accuracy is typically ±1.5% across -40 °C to +85 °C, and the divider chain supports decades from 1 to 9.54 hours via the DIV pin. The TSOT-23-6 footprint occupies just 2.9 mm × 1.6 mm of board area. Typical applications include industrial watchdog timers, battery-powered sleep/wake circuits, long-duration one-shot pulse generation, retriggerable monostable timing, periodic interrupt generation for microcontrollers, and replacement of electromechanical timing relays. Compared with a 555-based long timer, the LTC6995 eliminates large timing capacitors and offers an order-of-magnitude better stability over temperature. Designers should choose the RSET resistor to keep the master frequency between 4 kHz and 1 MHz (RSET between 50 kΩ and 800 kΩ) and place a 0.1 µF bypass capacitor close to the V+ pin. To extend the period beyond 9.54 hours, cascade a divider or feed the output into a counter. This page synthesizes distributor pricing, drop-in alternatives from the TimerBlox family, application recommendations, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
M21012 - 3.2 Gbps Quad Multi-Rate CDR | MACOM
M21012

M21012 - 3.2 Gbps Quad Multi-Rate CDR | MACOM

The MACOM Technology Solutions M21012 is a quad multi-rate clock and data recovery (CDR) integrated circuit with four independent channels for telecom and datacom systems. Each channel operates from 42 Mbps to 3.2 Gbps, and the device is identified in distributor data as a 72-QFN 10 mm by 10 mm fiber-channel, Gigabit Ethernet, and SONET clock-and-data-recovery IC. The verified product data also identifies an 800 MHz reference and one output for the related M21012G-12 ordering variant. A clock and data recovery IC is a semiconductor that extracts timing information from a noisy serial data stream and reconstructs a usable data signal. In the broader hierarchy, a CDR belongs to interface ICs and clock-and-timing recovery functions within high-speed data communications. The M21012 is intended for systems that need parallel adaptation of multiple serial links, particularly multi-lane telecom, optical networking, and datacom equipment. The principal verified feature is its four-channel multi-rate architecture. The 42 Mbps to 3.2 Gbps operating range allows one device family to address several link rates, while independent per-channel recovery supports multi-lane designs. The verified distributor listing also associates the related M21012G-12 variant with fiber-channel, Gigabit Ethernet, and SONET applications, an 800 MHz operating figure, and one output. Exact pin-level electrical limits, supply voltages, jitter specifications, and temperature ratings are not present in the supplied excerpts and must be confirmed from the manufacturer documentation before design release. For optical and backplane-oriented links, CDR functionality helps align serial data with its associated clock before downstream digital logic processes it. The recovered data can reduce the impact of timing distortion introduced by transmission media, connectors, packaging, and crosstalk. The quad organization can also reduce the number of separate recovery devices required in a multi-lane module, although board-level validation remains essential because channel-to-channel skew, power integrity, and loss characteristics depend on the complete implementation. Typical uses include SONET-oriented telecom interfaces, Gigabit Ethernet links, fiber-channel modules, multi-lane datacom equipment, and other serial links operating inside the stated 42 Mbps to 3.2 Gbps range. The exact supported coding, reference-clock requirements, recovery modes, and interface protocol details should be verified in the M21012 datasheet. Do not substitute the related M21012G-12 listing for the exact M21012 without confirming ordering-code compatibility. A practical design review should begin with the manufacturer pinout and package information, followed by high-speed transmission-line routing, controlled impedance, reference-clock integrity, decoupling, and thermal analysis. A CDR cannot compensate for an inadequately designed channel, and its benefit depends on the incoming signal remaining within the device's specified operating conditions. This page consolidates the verified manufacturer description, distributor application details, availability references, and engineering cautions for the M21012. It distinguishes verified facts from parameters requiring datasheet confirmation and does not present unverified substitute parts, electrical limits, pricing, or lifecycle claims as established data.

RFQ پەیوەندی
M41T65Q6F - Serial RTC with Alarm, I2C, 1.3V-3.6V | STMicroelectronics
M41T65Q6F

M41T65Q6F - Serial RTC with Alarm, I2C, 1.3V-3.6V | STMicroelectronics

The STMicroelectronics M41T65Q6F is a serial access real-time clock (RTC) integrated circuit with alarm functions, providing a complete Clock/Calendar function plus 32.768 kHz output in a 16-pin VQFN exposed-pad package. The device communicates through a 400 kHz I2C (2-wire serial) interface, operates from 1.3 V to 3.6 V supply, and integrates memory-mapped registers for seconds, minutes, hours, day, date, month, year, and century tracking with automatic leap-year compensation through the year 2100. A Real-Time Clock (RTC) is a category of low-power timing IC that maintains accurate wall-clock time and date information independent of the system microcontroller. RTCs are essential components in any battery-backed system that must preserve time-of-day across power cycles. The M41T65 belongs to the RTC IC > Clock/Calendar > I2C RTC sub-family, and within ST's product hierarchy it sits under Timekeeping ICs > Serial RTC > RTC with Alarms. RTCs bridge the gap between digital logic and physical time by using a 32.768 kHz crystal oscillator as the time-base reference and counting oscillator cycles to derive seconds, minutes, hours, and calendar days. Key features of the M41T65Q6F include a wide operating voltage range of 1.3 V to 3.6 V (suitable for direct battery backup operation), integrated alarm and interrupt functions, a programmable square-wave output derived from the 32.768 kHz crystal, low power consumption typically below 1 microamp in battery backup mode, and an automatic backup switchover when VCC falls below a defined threshold. The 16-pin VQFN-EP (QFN-16) exposed-pad package provides low thermal resistance for stable operation across the -40 °C to +85 °C industrial temperature range and supports automated PCB assembly. Architecturally, the M41T65Q6F combines a 32.768 kHz crystal oscillator, frequency divider chain, BCD-coded time/date registers, I2C interface logic, alarm comparators, and a trickle charger circuit. The internal oscillator drives a divider that produces 1-second resolution. Time and date are stored in Binary-Coded Decimal (BCD) format for direct display compatibility. The integrated trickle charger allows the device to recharge an external backup supercapacitor or rechargeable battery when main power is present, then automatically switch over to backup supply on VCC failure. Typical applications include metering and data-logging systems, industrial controllers requiring time-stamped events, point-of-sale (POS) terminals, medical devices needing scheduled dosing or data recording, consumer electronics with calendar/alarm functions, and any battery-backed embedded system that needs to wake the host MCU at scheduled times. The low 1.3 V minimum supply also makes the M41T65Q6F well-suited for single-cell battery systems. When designing with the M41T65Q6F, ensure the 32.768 kHz crystal load capacitance matches the datasheet specification (typically 12.5 pF) and place the crystal traces as short and symmetric as possible to minimize parasitic capacitance. A decoupling capacitor of 0.1 microfarad should be placed within 2 mm of the VCC pin. The exposed pad (EP) must be soldered to the ground plane for mechanical and thermal reliability. This page synthesizes distributor pricing, package-equivalent alternatives in the same ST M41Txx RTC family, and practical design notes not aggregated on the manufacturer datasheet PDF.

RFQ پەیوەندی
M41T81SM6F - Serial RTC 2.7-5.5V I2C 8-SOIC | STMicroelectronics
M41T81SM6F

M41T81SM6F - Serial RTC 2.7-5.5V I2C 8-SOIC | STMicroelectronics

The STMicroelectronics M41T81SM6F is a low-power serial real-time clock (RTC) with a built-in 32.768 kHz external-crystal-controlled oscillator, supplied in an 8-pin SOIC (SO-8) surface-mount package. It operates from 2.7 V to 5.5 V, communicates over a 400 kHz I2C (2-wire) serial interface, and provides a 64-byte BCD-formatted clock/calendar register map covering tenths/hundredths of seconds through century. A Real-Time Clock (RTC) is a dedicated integrated circuit that keeps track of wall-clock time even when the main system is powered down. RTCs sit at the bottom of the timekeeping hierarchy: RTC -> clock/calendar IC -> clock and timing -> semiconductor. They are essential wherever a system must maintain accurate time/date stamping across power cycles, such as data loggers, metering equipment, and industrial controllers. The M41T81S is one of the few RTCs that integrates both the 32.768 kHz crystal interface and the compensation circuitry in a single 8-pin package, reducing BOM and board area. Key features include 2.7 V to 5.5 V single-supply operation, low typical current consumption for battery-backed operation, programmable alarm and watchdog functions, automatic leap-year compensation through year 2099, and a software clock calibration function that can compensate crystal aging in 5 ppm steps. The I2C slave address is fixed at 0x68 with the A0 pin grounded. Internally, the M41T81S combines an external 32.768 kHz crystal oscillator circuit with a binary-coded decimal (BCD) counter chain. Eight bytes of on-chip SRAM back the clock/calendar registers and are accessed via the standard I2C protocol. The device supports both 100 kHz Standard-mode and 400 kHz Fast-mode I2C, making it compatible with most microcontroller families. The byte-wide register map follows the ST M41Txx family convention for drop-in software portability. Typical applications include industrial automation controllers, point-of-sale terminals, metering (electricity/water/gas), data loggers, medical devices requiring timestamped events, automotive telematics and infotainment subsystems, security and access-control panels, and any battery-backed embedded system needing persistent wall-clock time. When designing with the M41T81SM6F, place the 32.768 kHz crystal within 5 mm of the OSCIN/OSCOUT pins and guard those traces with a ground ring to minimize stray capacitance. Provide a backup battery (typically a 3 V coin cell) on VCC with a series Schottky or Schottky-plus-resistor OR-ing network so the RTC domain remains powered during main-rail outages. Use 100 nF decoupling close to VCC and observe the I2C pull-up sizing rules for the chosen bus speed. This page consolidates distributor pricing, parametric drop-in alternatives, and practical layout notes that complement the manufacturer datasheet, giving engineers a single reference for sourcing and designing in the M41T81SM6F.

RFQ پەیوەندی
M41T82RM6F - Low-Power I2C RTC with 32.768 kHz | STMicroelectronics
M41T82RM6F

M41T82RM6F - Low-Power I2C RTC with 32.768 kHz | STMicroelectronics

The STMicroelectronics M41T82RM6F is a low-power serial I2C real-time clock and calendar with a built-in 32.768 kHz oscillator, a 7-bit register address format, and an 8-pin SOIC package measuring 3.90 mm wide. It operates from a 2.0 V to 5.5 V clock supply range and provides battery-backed timekeeping with an ultra-low battery supply current of 365 nA. The device is designed for systems that require accurate calendar time, programmable alarms, periodic events, and low standby power. A real-time clock is a specialized timekeeping integrated circuit that maintains seconds, minutes, hours, date, day, month, and year information even when the main system is unpowered. The RTC category sits within clock and timing semiconductors, where crystal-based oscillators, dividers, registers, and digital interfaces work together to provide a stable time reference. Unlike a software timer, an RTC can continue counting through power loss and can be read again when the host processor restarts. The M41T82RM6F combines an external-crystal-controlled oscillator architecture with low-power serial communication. Its programmable alarm and timer functions can wake a connected microcontroller or signal that a scheduled interval has elapsed. The I2C interface reduces wiring requirements in compact embedded systems, while the 2.0 V to 5.5 V operating range supports both low-voltage and conventional supply environments. The 365 nA battery supply current is especially relevant for battery-backed meters, industrial recorders, and portable instruments. The STMicroelectronics M41T82 family description identifies the SO8 version as using an external 32.768 kHz crystal. Accurate timekeeping therefore depends not only on the RTC electronics but also on crystal selection, load-capacitance matching, layout quality, and temperature behavior. The M41T82RM6F is suited to data loggers, access-control terminals, metering equipment, industrial controllers, and consumer products requiring persistent timestamps. Its low standby consumption helps reduce energy use when the main supply is absent. For a robust design, place the RTC and its crystal close together on the PCB, keep high-current switching paths away from the oscillator network, and provide the required bypass capacitance. Confirm the exact pin functions, register behavior, alarm polarity, and electrical limits against the manufacturer datasheet before layout release. The verified source data supports the component identity, package, interface, oscillator, supply range, and low-current claims; additional operating details remain subject to the full STMicroelectronics datasheet. This page combines verified manufacturer and distributor information with application guidance, comparison fields, and design notes. It is intended to help engineers identify whether the M41T82RM6F fits a low-power battery-backed timekeeping design while distinguishing verified facts from parameters requiring confirmation from the latest datasheet.

RFQ پەیوەندی
M41T94MQ6F - Serial RTC 44B NVRAM SPI 16-SOIC | STMicroelectronics
M41T94MQ6F

M41T94MQ6F - Serial RTC 44B NVRAM SPI 16-SOIC | STMicroelectronics

The STMicroelectronics M41T94MQ6F is a serial real-time clock (RTC) with 44 bytes of NVRAM and a RESET output, packaged in a 16-pin SOIC (0.154", 3.90 mm width). It provides a complete clock/calendar function with tenths/hundredths of seconds, seconds, minutes, hours, day, date, month, year, and century counters, and communicates with the host MCU through a 4-wire SPI bus at clock rates up to 2 MHz. The internal 32,768 Hz oscillator integrates 12.5 pF of load capacitance, allowing direct connection of an external tuning fork crystal without external load capacitors while still tolerating high crystal series resistance (up to 80 kΩ typical). A real-time clock (RTC) is a low-power integrated circuit that maintains accurate wall-clock time using a quartz crystal reference, even when the main system is powered down. RTCs sit within the broader hierarchy of clock-and-timing ICs, which include general-purpose timers, oscillators, and PLL/clock generators. Unlike MCU-internal time counters, dedicated RTC ICs add battery backup switchover, calendar logic, and non-volatile user memory that survives both system reset and loss of main supply. Key features of the M41T94MQ6F include SPI serial interface, 44 bytes of battery-backed NVRAM (16 bytes general-purpose plus 8 bytes used by the clock/calendar), a RESET output pin that asserts a fixed-duration low pulse for system brown-out management, and an integrated 32 kHz oscillator with on-chip load capacitance. The device operates from 2.7 V to 5.5 V main supply and is specified for the industrial -40 °C to +85 °C temperature range. Typical applications include metering (electricity/water/gas), point-of-sale terminals, data loggers, industrial controllers, and any embedded system that needs a tamper-resistant, battery-backed time stamp separate from the application MCU. Designers should add a lithium backup cell (or supercapacitor) to the VBAT pin and follow the crystal-layout guidance in the ST datasheet for long-term timekeeping accuracy.

RFQ پەیوەندی
MALD-37545 - Quad 22.5G/25.78G CDR VCSEL Driver | MACOM
MALD-37545

MALD-37545 - Quad 22.5G/25.78G CDR VCSEL Driver | MACOM

MACOM MALD-37545 is a four-channel CDR/VCSEL driver with an integrated input equalizer, operating at 22.5 Gbps or 25.78 Gbps per channel for complete single-chip optical transmit solutions. The verified product information identifies the device as a quad 25.78 Gbps VCSEL driver with integrated clock and data recovery and equalization. Its 22.5 Gbps and 25.78 Gbps operating modes target high-speed optical-module links where transmit-channel density and signal conditioning are important. The package and detailed electrical, environmental, and compliance parameters are not present in the supplied verified data and require confirmation from the manufacturer datasheet. A clock and data recovery IC is a high-speed interface component that reconstructs a usable clock and recovers the digital data stream from a degraded incoming signal. Optical transmit paths commonly combine recovered data with laser-driver circuitry so that one device can condition the input and drive a VCSEL. The MALD-37545 integrates those transmit functions across four channels, reducing the need for separate equalizer and CDR blocks when the module architecture and board layout are compatible. The primary verified feature set is its four-channel organization, 22.5 Gbps and 25.78 Gbps data rates, integrated CDR, integrated input equalizer, and VCSEL-driver output stage. These features make it relevant to optical communications, high-speed optical modules, parallel transmit links, and data-center or telecommunications equipment. The equalizer addresses input-channel degradation before data recovery, while the CDR supplies timing recovery and the driver stage interfaces the recovered signal to the optical transmitter. Operation at these data rates requires a controlled high-speed layout and careful separation between sensitive receive or recovery paths and output-driver return currents. Board designers should follow the MACOM evaluation and reference guidance for differential impedance, controlled impedance routing, termination, bypassing, and connector or package transitions. Because the supplied data does not state differential impedance, supply voltage, current, lane-to-lane skew, jitter, package dimensions, pinout, operating temperature, or qualification status, those values must not be assumed. The MALD-37545 is best suited to a new optical-module design when its exact pinout, package, power architecture, and channel performance have been validated against the current manufacturer documentation. It may not be interchangeable with a lower-rate laser driver or a CDR-only device without a full timing, signal-integrity, power, and pin-compatibility review. Use the official MACOM product page and datasheet before releasing production hardware. This page distinguishes the MALD-37545 from generic laser drivers by emphasizing the integrated equalizer and CDR architecture. It also records the data that is genuinely verified and leaves unsupported technical claims as data-needed fields. Design selection should be based on the manufacturer datasheet, system loss budget, laser requirements, power budget, and module certification constraints rather than on generic high-speed-driver assumptions.

RFQ پەیوەندی
MASC-37446 - Quad 25.78/28.05Gbps CDR | MACOM
MASC-37446

MASC-37446 - Quad 25.78/28.05Gbps CDR | MACOM

MACOM MASC-37446 is a four-channel 24G/25G clock and data recovery IC with integrated limiting amplifiers, supported in a package that is not specified in the verified source data. Each channel provides retiming at 25.78 Gbps, 27.95 Gbps, or 28.05 Gbps, while the device supports case temperatures from -40°C to +85°C. The four-channel architecture is intended for receive-side optical modules that require recovered data and clock outputs from high-speed serial signals. A clock and data recovery IC is a semiconductor that reconstructs a usable clock from a serial data stream and aligns data to that recovered timing reference. In the optical communications hierarchy, a CDR belongs to clock-and-timing ICs and supports transceivers, optical receivers, backplane links, and other high-bandwidth data paths. Unlike a fixed-delay retimer, a CDR is intended to reduce accumulated timing jitter while restoring margin through the receive path. The MASC-37446 combines four independent channels with a high-sensitivity limiting amplifier, a high-performance CDR, and an output driver in each channel. The verified manufacturer description identifies programmable output swing and two-tap de-emphasis, features useful for controlling output voltage and compensating for channel loss in a multi-gigabit interface. It also offers extracted clock outputs at fb/2, fb/8, fb/32, or fb, depending on the device configuration described by MACOM. The device is positioned for 24G/25G optical-module receive designs rather than general-purpose digital logic. Reference-free CDR operation can reduce the need for an external reference in suitable architectures, while low output jitter and high input jitter tolerance address two central challenges in 25.78/28.05 Gbps links. The operating range of -40°C to +85°C case temperature supports industrial-temperature qualification goals, although the verified data does not explicitly state an AEC-Q100 qualification status. Typical uses include four-lane optical-module receivers, high-speed optical transceivers, copper backplane retiming, test and measurement equipment, and data-center interconnect links. When designing around MASC-37446, confirm the exact package pinout, supply rails, input sensitivity, output swing settings, de-emphasis configuration, and layout requirements against the current MACOM documentation; these details were not present in the supplied search excerpts. This page synthesizes the verified MACOM product description, supported data rates, temperature range, channel functions, extracted-clock options, and design caveats into an engineering-oriented reference for sourcing and initial architecture selection.

RFQ پەیوەندی
MASC-38040 - 28.9 GBaud 4-Channel PAM-4 CDR | MACOM
MASC-38040

MASC-38040 - 28.9 GBaud 4-Channel PAM-4 CDR | MACOM

MACOM MASC-38040 is a four-channel, reference-free clock and data recovery retimer operating from 25.78 GBaud to 28.9 GBaud in a 5.2 mm x 5.2 mm QFN-compatible package. Its headline specifications are four PAM-4 channels, 28.9 GBaud maximum signaling rate, and single 1.8 V supply operation. Each channel can be controlled through a two-wire I2C-compatible interface, while a bypass mode supports legacy or nonstandard data rates. A clock and data recovery retimer is an IC that recovers a usable clock from a high-speed serial stream, resynchronizes data, and can compensate for accumulated timing and jitter problems. In the optical and digital-communications hierarchy, the MASC-38040 belongs to retiming CDR and clock-and-data recovery devices used in PAM-4 links operating at tens of gigabauds. Key features include reference-free operation across 25.78 to 28.9 GBaud, four independently controllable channels, bypass support, and a single 1.8 V power rail. The two-wire I2C-compatible control path simplifies configuration of multiple lanes. These characteristics suit systems requiring one retiming device to manage several parallel high-speed links rather than using separate single-channel recovery circuits. Technically, the device is positioned for 56G-class PAM-4 receive paths, where source, package, connector, and trace losses can impair timing recovery. Reference-free CDR operation is useful when the transmitter does not provide a separate usable reference. Bypass mode adds deployment flexibility for legacy or nonstandard rates, although the verified source does not specify which rates and modes are supported. Typical uses include 400G and 800G optical receivers, coherent communication modules, high-speed optical DSP test systems, and parallel data links. Each lane can be configured through the common control interface, helping synchronize operating states across a multi-channel receiver. PCB design should preserve short high-speed differential routes, continuous reference planes, and symmetrical via transitions. The 1.8 V rail requires local high-frequency decoupling and adequate return paths. Engineers must consult the manufacturer documentation for exact pin assignments, electrical limits, channel-count interpretation, bypass behavior, and exposed-pad requirements. This page consolidates the verified manufacturer specifications and explicitly identifies missing technical, commercial, pinout, compliance, and replacement data rather than estimating it. It also distinguishes a true pin-compatible replacement from unrelated QFN clock-and-data recovery devices.

RFQ پەیوەندی
MATA-37144 - Selectable-Bandwidth TIA/CDR | MACOM | Optical
MATA-37144

MATA-37144 - Selectable-Bandwidth TIA/CDR | MACOM | Optical

The MACOM Technology Solutions MATA-37144 is a four-channel 25G/28G clock and data recovery amplifier with an integrated high-sensitivity transimpedance amplifier, limiting amplifier, and programmable output driver. Its selectable TIA bandwidth supports legacy data rates, while programmable slice level, loss-of-signal threshold, output swing, and de-emphasis provide receiver-chain control. The supplied data does not state the package or its physical dimensions. A clock and data recovery amplifier, or CDR, reconstructs a usable digital data stream and recovered clock from a degraded high-speed optical signal. This MACOM device combines the photodiode-input TIA, decision circuitry, and output-driver functions in one optical receiver path. In the signal-chain hierarchy, it belongs to clock and timing components and interface electronics, rather than a general-purpose digital logic IC. The MATA-37144 is specifically identified as a four-channel 25G/28G CDR with an integrated TIA. Its high-sensitivity TIA includes selectable bandwidth for legacy-rate support. After amplification, the limiting amplifier provides a defined decision function, while programmable output swing and de-emphasis allow downstream circuitry to be matched to channel and board conditions. Programmable slice-level adjustment and LOS-threshold control support receiver calibration and loss-of-signal detection. The verified source also associates the MATA-37144 with an average photodiode-current monitor identified as RSSI. This measurement feature helps a system evaluate received optical power indirectly. Together, the TIA, slicer, LOS control, RSSI monitoring, and programmable driver create a configurable receiver chain rather than a fixed-gain amplifier. Exact gain, sensitivity, bandwidth selections, data rates, supply voltage, power consumption, and channel-to-channel coupling require datasheet verification. The most relevant applications are 25G/28G optical transceiver receivers, legacy-rate-compatible optical links, parallel four-channel architectures, receiver equalization and de-emphasis experiments, and loss-of-signal monitoring systems. For these uses, designers should evaluate channel budget, photodiode capacitance, target line rate, recovery range, output impedance, and PCB channel loss before committing to a receiver implementation. A key design consideration is that programmable bandwidth, slice level, LOS threshold, output swing, and de-emphasis do not replace optical-power budgeting or channel simulation. Set receiver controls through validated firmware, preserve receiver eye margin, and verify compliance with the exact variant datasheet. The available evidence does not identify whether MATA-37144 is a catalog, die, tape-and-reel, or other package configuration. This page separates verified manufacturer-level facts from unavailable parameters and records every missing electrical or package attribute rather than estimating it. It also explains why a same-footprint replacement cannot be recommended until the package and pinout are verified. For an equivalent device, compare data rate, channel count, optical input sensitivity, bandwidth modes, LOS behavior, RSSI implementation, electrical interfaces, supply requirements, and package-level pin compatibility.

RFQ پەیوەندی
MAX038CPP+ - 40MHz Precision Waveform Generator | Analog Devices
MAX038CPP+

MAX038CPP+ - 40MHz Precision Waveform Generator | Analog Devices

The Analog Devices MAX038CPP+ is a precision high-frequency function-generator IC delivering a 40 MHz maximum carrier frequency and a 2 V peak-to-peak output in a 20-pin DIP package. According to the manufacturer product page, it generates triangle, sawtooth, sine, square, and pulse waveforms, with independent frequency and duty-cycle controls and a low-impedance output capable of driving ±20 mA. The MAX038 family combines a waveform synthesizer and output buffer for instrumentation, stimulus, modulation, and signal-generation systems. A function generator is an electronic signal-source category used to create periodic test or excitation waveforms with controlled frequency, amplitude, and timing. Within the broader Clock & Timing hierarchy, the MAX038 is a clock generator and waveform generator rather than a general-purpose timer. Its low external-component count simplifies analog signal sources while its selectable waveforms support both laboratory-style stimulus and embedded system clocking. The MAX038CPP+ provides selectable sine, square, or triangle output through TTL-compatible select pins. Its output is symmetrical around ground, making it convenient for bipolar-referenced circuits. Frequency and duty-cycle adjustments are independent, while sweep support extends the usefulness of the device beyond fixed-frequency operation. These features let a designer vary stimulus conditions without changing the output architecture. The MAX038 architecture is intended for precision waveform generation at frequencies up to 40 MHz. The manufacturer lists a 2 V peak-to-peak output, low output impedance, and output drive of ±20 mA. The output drive specification is important when selecting termination, amplifier, cable, or load components: downstream circuitry must present a compatible load, and cable capacitance can degrade waveform quality at higher frequencies. Typical uses include bench and portable test equipment, audio and communications signal generation, industrial stimulus systems, pulsed sensor testing, and educational waveform laboratories. The output buffer reduces the need for a separate line driver when the load is modest, while selectable waveforms make the device useful for functional checks involving sine, square, triangle, sawtooth, and pulse signals. A key design consideration is that the MAX038CPP+ is a through-hole 20-pin DIP device, not a surface-mount part. PCB footprint, pin orientation, trace routing, and output termination should therefore be checked against the manufacturer datasheet before substitution. Waveform quality also depends on external resistor, capacitor, reference, and layout choices documented in the application information. This page combines verified manufacturer specifications, distributor availability references, package details, and engineering-focused selection guidance. It is designed to help engineers identify whether the MAX038CPP+ fits a particular waveform-generation, timing, or test-stimulus requirement.

RFQ پەیوەندی
MAX038CWP+ - 20MHz Precision Waveform Generator | Analog Devices
MAX038CWP+

MAX038CWP+ - 20MHz Precision Waveform Generator | Analog Devices

The Analog Devices MAX038CWP+ is a precision high-frequency waveform generator IC covering 0.1Hz to 20MHz and producing triangle, sawtooth, sine, square, and pulse outputs. Frequency is set by an external resistor and capacitor referenced to an internal 2.5V bandgap, while a low-impedance output buffer drives the resulting waveform. The device is supplied in a 20-pin SOIC package. A function generator or waveform generator is an active analog signal-source category that converts a frequency-setting network into repeatable time-domain waveforms. Within the broader hierarchy, the MAX038 belongs to clock and waveform generation, then integrated circuits and semiconductors. It consolidates multiple waveform outputs and frequency and duty-cycle controls into one circuit, reducing the component count required for bench instruments, signal-conditioning systems, and industrial test equipment. Verified features include a 20MHz upper frequency, a 0.1Hz lower frequency, independent frequency and duty-cycle adjustments, variable duty cycle up to 85%, and frequency sweep capability. Its internal 2.5V bandgap provides the reference for the external timing components. The output stage is specified as a low-impedance buffer with 0.1-ohm output impedance, helping the generator interface more effectively with downstream analog and digital test circuits than a passive or high-impedance source would. The MAX038 family generates five principal waveform formats from a common internal timing architecture. Triangle and sawtooth outputs suit ramp-based stimulus and sweep systems, sine output supports analog excitation, and square or pulse output provides clock-like and duty-cycle-adjustable signals. Frequency and duty-cycle adjustment remain independent, allowing output timing to be changed with separate external networks rather than tying both characteristics to one component. Typical uses include audio test equipment, sensor and transducer excitation, communications signal testing, automated production-test systems, function generators, and general laboratory stimulus sources. The MAX038 is especially useful when one IC must support multiple waveform formats and frequencies up to 20MHz without building separate analog oscillator paths. Designers should treat output loading, timing-component tolerances, reference accuracy, and bandwidth limits as the main engineering constraints. Place the frequency-setting resistor and capacitor close to their associated pins, maintain the specified supply and bypass conditions, and verify downstream input capacitance before assuming the 0.1-ohm buffer can drive arbitrary loads. This page consolidates manufacturer specifications, sourcing status, verified drop-in candidates, and application guidance. It separates confirmed data from unavailable parameters and explicitly flags the absence of a manufacturer replacement, helping engineers assess whether an existing MAX038 design can be maintained without an unsupported substitution.

RFQ پەیوەندی
MAX35103EHJ+ Reduced-Power ToF Converter | Analog Devices
MAX35103EHJ+

MAX35103EHJ+ Reduced-Power ToF Converter | Analog Devices

The Analog Devices MAX35103EHJ+ is a reduced-power time-to-digital converter with an integrated analog front end, real-time clock, and flash memory, specified for a 2.3 V to 3.6 V supply in a 32-pin TQFP (5 mm × 5 mm) package. It targets ultrasonic heat, water, and gas meters and increases the maximum time-of-flight measurement frequency in event timing mode from 2 Hz on the MAX35101 to 16 Hz. A time-to-digital converter, or ToF converter, measures the elapsed time represented by an ultrasonic pulse by converting a timing event into a digital result. The MAX35103 integrates the pulse-generation, receive-signal conditioning, timing, clock, and nonvolatile-measurement functions required by a compact ultrasonic metering front end. This integration reduces external circuitry compared with a discrete timer and analog receive chain while preserving a path to low-cost, low-power meter designs. According to the manufacturer datasheet, the MAX35103 consumes about half the average power of the MAX35101. The supplied sources do not provide a numeric average-current value, oscillator accuracy, ToF resolution, measurement range, flash capacity, temperature range, or absolute timing accuracy, so those values require confirmation in the datasheet or device evaluation before design release. The listed operating supply range is 2.3 V to 3.6 V. The integrated real-time clock and flash support metering designs that need timekeeping and persistent measurement data alongside ultrasonic time-of-flight conversion. The 16 Hz maximum event-timing frequency is particularly relevant when the meter must update more frequently than the MAX35101. Firmware, calibration, echo detection, and time-of-digital compensation still determine achievable accuracy and must be evaluated with real transducers and meter mechanics. Typical uses include ultrasonic heat meters, water meters, and gas meters. An Analog Devices evaluation kit installs the MAX35103EHJ+ and includes a USB-to-SPI interface plus graphical software for exercising device functionality. The supplied distributor records list the MAX35103EHJ+ in a 32-TQFP package and identify it as a CMOS-input, CMOS-output time-to-digital converter IC. For PCB design, place decoupling and timing-critical paths according to the manufacturer layout guidance and keep the ultrasonic analog front end away from switching nodes and digital return-current paths. Validate transducer drive amplitude, receive gain, threshold timing, clock calibration, and flash endurance under the intended flow, temperature, and supply conditions. Do not infer production suitability from the general-purpose EV kit alone.

RFQ پەیوەندی
MC14029BD - 4-Bit Binary/BCD Up/Down Counter | onsemi
MC14029BD

MC14029BD - 4-Bit Binary/BCD Up/Down Counter | onsemi

The onsemi MC14029BD is a 4-bit binary/decade up/down counter built with complementary MOS P-channel and N-channel enhancement-mode devices in a single monolithic structure. The device supports binary counting and BCD operation, with four complementary outputs, an asynchronous parallel load function, and separate count-up and count-down clock inputs. It is packaged in a 16-pin SOIC for surface-mount assembly. A binary counter is a sequential digital circuit that stores or tracks a number of clock events and advances or reverses its state through a defined sequence of binary states. The MC14029B extends this category with selectable binary or decimal counting, making it a logic IC within the broader counter, divider, and clock-and-timing hierarchy. Its decade mode supports values from 0 through 9 before rollover, while binary mode supports a 4-bit count from 0 through 15. The counter consists of type-D flip-flop stages with gating that provides toggle capability. Separate count-up and count-down inputs allow the counting direction to be selected, and asynchronous load inputs provide a parallel mechanism for initializing the output state. The complementary outputs support both active-high and active-low counting signals, making the device suitable for modular counters, programmable timing systems, sequence generators, and industrial control logic. The MC14029B family is identified as a CMOS counter constructed from P-channel and N-channel enhancement-mode devices. CMOS construction is significant in digital systems because it supports low static power dissipation relative to the switching activity, while complementary logic can provide rail-to-rail output levels and noise margin benefits. The operating voltage, clock frequency, output current, and environmental limits should be taken from the manufacturer datasheet when designing a new circuit. Typical uses include bidirectional event counting, frequency division, decade sequencing, pulse-train generation, and embedded control logic. The binary/BCD selection allows the same physical counter to support both hexadecimal-style state progression and decimal displays or decade-based timing systems. In cascaded designs, multiple MC14029BD devices can form larger counters when the application requires more than four count bits. For PCB implementation, place the device close to the signals it drives and route clock, reset, load, and carry inputs away from sensitive analog or high-speed clock networks. The asynchronous load and reset controls should be checked against the system timing budget because their assertion can change the counter outputs independently of the counting clock. Decoupling requirements, maximum transition rates, and input logic levels must follow the manufacturer datasheet. This page combines the family-level device description, package information, a source-linked pricing record, compatible same-family references, and practical implementation guidance. It is intended to help engineers identify the correct counter function, verify the 16-pin surface-mount footprint, and plan logic-level, timing, and layout decisions before releasing a PCB.

RFQ پەیوەندی
MC14046BF - 1.9MHz Phase-Locked Loop IC | onsemi
MC14046BF

MC14046BF - 1.9MHz Phase-Locked Loop IC | onsemi

The onsemi MC14046BF is a CMOS phase-locked-loop IC with a maximum operating frequency of 1.9 MHz, supplied in a 16-pin SOIC package measuring 5.30 mm wide. The device combines two phase comparators, a voltage-controlled oscillator, a source follower, and a zener diode. Its phase-locked-loop architecture synchronizes an output signal with a reference input, making it suitable for frequency synthesis, frequency multiplication, frequency division, modulation, tone generation, and other clock-and-timing systems. A phase-locked loop is a feedback-control circuit that compares two signals and adjusts a controllable oscillator until the phase or frequency relationship reaches the required condition. The MC14046BF belongs to the PLL family within clock-generation and timing ICs. Its internal phase comparators detect differences between input signals, while the voltage-controlled oscillator varies its output frequency according to a control voltage. The source follower provides an interface to the timing network, and the zener diode supports stable operation in the intended CMOS supply range. The main feature of the MC14046BF is its 1.9 MHz maximum operating frequency. This makes the IC appropriate for signal-generation and synchronization tasks that do not require the multi-gigahertz rates of a modern fractional-N synthesizer. Its 16-pin SOIC package supports conventional surface-mount PCB assembly while exposing the comparator, VCO, source-follower, and zener functions needed for external timing components. The broad integration reduces the number of separate blocks required in a basic PLL implementation. In operation, the phase comparators evaluate the relationship between the input and feedback signals. Their control output is applied to the voltage-controlled oscillator through an external timing network, causing the oscillator to change frequency until the loop reaches its locked condition. The source-follower output can be used to develop a compatible feedback or timing signal. External resistors and capacitors determine loop dynamics, operating range, filtering, and startup behavior, so component selection and layout remain important parts of the design. Typical applications include FM and AM demodulation, tone decoding, frequency multiplication, frequency division, clock recovery, synchronized signal generation, and low-to-medium-frequency synthesis. The 1.9 MHz operating limit makes the MC14046BF especially relevant to communications, instrumentation, industrial control, audio-frequency systems, and embedded timing circuits where a flexible analog PLL is more suitable than a fixed-frequency clock oscillator. The primary design consideration is the external analog network around the PLL. Capacitor values, resistor tolerances, comparator polarity, VCO control-voltage limits, and loop filtering directly affect lock range and stability. Keep the timing and feedback paths compact, use a low-noise supply, and verify both acquisition and steady-state phase error across the required temperature range. This page combines the verified 1.9 MHz frequency and 16-SOIC package information with practical implementation guidance, selection criteria, pinout-status clarification, and same-package replacement analysis. These engineering notes help distinguish a usable direct replacement from a merely similar PLL before committing to a PCB redesign.

RFQ پەیوەندی
MC145170D2 - 185MHz PLL Frequency Synthesizer | NXP
MC145170D2

MC145170D2 - 185MHz PLL Frequency Synthesizer | NXP

NXP Semiconductors MC145170D2 is a single-chip PLL frequency synthesizer with a maximum operating frequency of 185 MHz, supplied in a 16-pin SOIC package. It combines fully programmable R and N counters, an input amplifier, crystal-oscillator support, a programmable reference output, and both single-ended and double-ended phase detectors. The double-ended detector uses a linear transfer function without a dead zone, making the device suitable for precision phase-control and frequency-generation systems. A phase-locked loop, or PLL, is a feedback-controlled timing circuit that locks an output frequency to a reference frequency. The PLL frequency synthesizer category sits within clock and timing integrated circuits, where it supports clock generation, frequency multiplication, modulation, and phase alignment. The MC145170 family was designed for direct use in MF, HF, and VHF bands, combining digital counters and analog phase-detection functions on one integrated circuit. Programmable R and N counters allow the relationship between the reference input and synthesized output to be established by register programming. The device supports an external crystal at the input amplifier, while the programmable reference output provides a convenient reference for other system blocks. Its maximum specified quiescent supply current remains 100 μA, making it practical for low-power frequency-control equipment when the operating conditions permit low current consumption. The MC145170-2 uses a more responsive power-on reset circuit than MC145170-1. According to NXP, both devices use the same chip with different power-on-reset mask options, and the MC145170-2 is recommended for new designs. This reset behavior is especially useful when a brief supply interruption could otherwise leave internal counters or the phase comparator in an incorrect state. The MC145170-2 is also identified as pin-for-pin compatible with MC145170-1. Typical uses include local-oscillator generation in radio receivers and transmitters, FM and phase-modulation systems, frequency-agile communications equipment, industrial instrumentation, and low-power RF test equipment. The 185 MHz operating limit provides useful range for VHF designs, while the 16-pin SOIC package supports conventional surface-mount assembly. System designers should account for the required loop filter, reference source, divider programming, and decoupling network shown in the manufacturer’s application guidance. For a new design, confirm that the selected reference frequency, counter ratio, loop bandwidth, and required reference output can be supported by the internal divider arrangement. Place the input and reference-network components close to their associated pins, use a clean and stable reference source, and verify startup and reacquisition behavior across supply interruptions. The D suffix denotes the 16-pin SOIC ordering option identified by the product listing. This page combines the manufacturer’s device capabilities, package information, family compatibility details, application guidance, and drop-in replacement analysis. It also organizes the most important selection constraints into a practical guide for evaluating the MC145170D2 in PLL-based RF and timing designs.

RFQ پەیوەندی
MC14536BCP - 2MHz Programmable Timer | onsemi
MC14536BCP

MC14536BCP - 2MHz Programmable Timer | onsemi

The onsemi MC14536BCP is a 2 MHz programmable timer IC packaged in a 16-pin PDIP. Its core architecture is a 24-stage binary ripple counter with 16 stages selectable through a binary control code. The manufacturer also identifies provisions for an on-chip RC oscillator or an external clock, along with an on-chip monostable circuit that produces a pulse-type output. A programmable timer is a timing and counting semiconductor used to divide a clock, generate a delayed or fixed-duration pulse, and organize periodic events in digital systems. In the broader hierarchy, the MC14536BCP belongs to the clock and timing IC category, where it combines counter, oscillator-interface, and monostable functions. Selectable counter stages let a system obtain several timing periods from one input frequency without requiring a separate divider for each interval. The principal functional attributes are its 24-stage binary ripple-counter organization, 16 binary-selectable stages, support for either the internal RC timing path or an external clock input, and a monostable output path. The listed 2 MHz frequency identifies the device’s stated operating-speed class. Together, these features allow the MC14536BCP to cover repetitive timing, pulse generation, elapsed-time measurement, and clock-frequency division functions in one circuit. The counter architecture provides a direct relationship between input-clock frequency and selected output period. When a stage is selected, the associated ripple-counter output changes at a predictable fraction of the incoming clock. The monostable section adds a separate pulse-duration function, allowing the same timer IC to serve both periodic counting and event-triggering requirements. External timing components can be used with the RC oscillator path, while an external clock gives the circuit a reference with independently controlled accuracy and stability. Typical applications include industrial pulse and delay generation, test and measurement sequencing, laboratory timer circuits, control-system event counters, low-speed clock dividers, and embedded logic that needs a selectable output period. In these systems, the binary stage-selection inputs determine the timing ratio, while the clock source determines the absolute operating frequency and accuracy. The integrated monostable function is particularly useful when a load must receive a defined pulse after a triggering event. Designers should verify the power-supply limits, oscillator-component tolerances, timing limits, output characteristics, and absolute maximum ratings in the manufacturer datasheet before finalizing a circuit. External clock and reset timing must also be checked against the system requirement, because the programmable divider changes frequency but does not improve the accuracy of its time reference. PCB layout should keep timing-node connections short and provide adequate decoupling near the device. This product summary combines the manufacturer architecture description with package, function, sourcing, replacement, and design guidance. It focuses on the practical role of the selectable counter stages, the choice between RC and external-clock timing, and the constraints that must be checked when reusing an existing 16-pin timer design.

RFQ پەیوەندی
MC14541BD - 3MHz Programmable Timer | onsemi | Clock IC
MC14541BD

MC14541BD - 3MHz Programmable Timer | onsemi | Clock IC

The onsemi MC14541BD is a programmable timer IC with a maximum oscillator frequency of 3 MHz, a 16-stage binary counter, and an integrated oscillator in a 14-pin SOIC package. It is designed for applications that require an external resistor-capacitor timing network, automatic initialization at power-on, and programmable timer output control. A programmable timer is a clock-and-timing semiconductor that counts oscillator cycles and derives a delayed or periodic output. Within the broader device hierarchy, the MC14541BD belongs to the timer-counter category, combining a frequency-stable timing element with digital counter and output-control logic. This makes it useful when a circuit needs a basic time interval or recurring output generated locally from a small number of external timing components. The MC14541BD contains three primary functional blocks. Its integrated oscillator operates with an external capacitor and two resistors, while its 16-stage binary counter provides the counting structure used to create timing intervals. An automatic power-on reset circuit initializes the counter when power is applied, reducing the need for external reset sequencing in straightforward timing designs. Output control logic governs the behavior of the timer output. The 3 MHz maximum oscillator frequency establishes the upper operating point for the internal oscillator. Actual operating frequency depends on the selected external resistor-capacitor network, component tolerances, temperature, supply conditions, and the electrical characteristics of the timing network. Designers should select timing components against the manufacturer datasheet limits and verify frequency tolerance across the intended temperature range rather than assuming a perfectly constant period. Typical uses include general-purpose delay generation, periodic pulse generation, industrial control timing, oscillator-based clocking, and embedded timing subcircuits. The device can also serve as a building block in test fixtures and small control systems where an autonomous timer is more convenient than relying on a host microcontroller. The 14-pin SOIC package supports conventional surface-mount assembly and is also available in legacy through-hole-oriented component ecosystems. The principal design consideration is the oscillator network. Place the external resistor and capacitor close to their associated pins, use low-tolerance parts when timing accuracy matters, and reserve adequate ground-return paths to minimize coupling into the counter and output circuitry. Because power-on reset starts the timing sequence automatically, software or external logic should treat the first output transition as an initialization event rather than an arbitrary control signal. This product page consolidates the verified device identity, oscillator and counter features, package information, sourcing options, and drop-in replacement guidance. It also adds practical selection criteria and design notes for engineers evaluating the MC14541BD against other 14-pin programmable timer implementations.

RFQ پەیوەندی
MC14541BDG - 3MHz 16-Stage Timer IC | onsemi
MC14541BDG

MC14541BDG - 3MHz 16-Stage Timer IC | onsemi

The onsemi MC14541BDG is a programmable timer integrated circuit with a 3 MHz maximum oscillator frequency, a 16-stage binary counter, and an integrated 14-pin SOIC package. It operates from 3 V to 18 V and is designed for frequency division, periodic timing, delay generation, and general-purpose industrial control applications. Its internal oscillator uses an external capacitor and two resistors, while automatic power-on reset and output control logic simplify standalone timer implementation. A programmable timer is a clock and timing IC that divides a known input frequency or generates a periodic output using a counter and oscillator. The MC14541B belongs to the broader timer hierarchy that includes oscillator, counter, monostable, and astable timing functions. Its oscillator and binary counter are normally used together to create a stable, adjustable clock output without requiring a separate microcontroller for simple repetitive timing tasks. The 16-stage counter provides programmable division ratios and supports repetitive waveform generation. The integrated oscillator accepts external timing components, allowing the operating frequency to be set with external resistor and capacitor values. A 3 V to 18 V supply range covers low-voltage logic systems through conventional industrial control voltages, while the specified -55 °C to 125 °C temperature range supports demanding industrial environments. The architecture separates the oscillator, 16-stage binary counter, automatic power-on reset, and output control logic into one integrated device. Automatic power-on reset establishes a defined starting condition after power is applied, reducing initialization effort. The output stage provides a periodic signal derived from the divided counter clock, allowing the IC to serve as the central timing element in small control, sequencing, and periodic-trigger systems. Typical uses include industrial pulse generation, repetitive equipment-cycle timing, delayed switching, frequency division, oscillator replacement, and embedded control subcircuits. The device is particularly useful where a fixed clock, a low-frequency service pulse, or a divided timing signal is required but a programmable microcontroller would add unnecessary complexity. Its broad supply range also allows one timer design to be used across multiple logic voltage environments. Choose external oscillator components with tolerances suitable for the required timing accuracy, and verify the resulting frequency across temperature and supply-voltage extremes. Place the timing capacitor and resistors close to the relevant device pins, keep the output load within the specified drive capability, and account for counter overflow when defining pulse timing. Confirm reset behavior and output polarity against the manufacturer datasheet for the selected system configuration. This page combines the manufacturer timing architecture, operating limits, package details, verified sourcing references, drop-in candidates, comparison parameters, and practical PCB guidance. It also distinguishes the tube-packaged MC14541BDG from related ordering codes and identifies which electrical details require confirmation for each candidate before PCB or production use.

RFQ پەیوەندی
MC14541BDT - 3 MHz Programmable Timer | onsemi | Clock & Timing
MC14541BDT

MC14541BDT - 3 MHz Programmable Timer | onsemi | Clock & Timing

The onsemi MC14541BDT is a programmable timer integrated circuit built around a 16-stage binary counter, an integrated oscillator, automatic power-on reset, and output-control logic. It operates to a maximum clock frequency of 3 MHz, supports supply voltages up to 18 V, and is specified over a -55 °C to +125 °C temperature range. The device is associated with a 14-pin small-outline package and is supplied in tape-and-reel form with the T ordering suffix. A programmable timer is a clock-and-timing IC that divides an input frequency into a selectable output interval. In the MC14541B family, the oscillator can use an external capacitor and two resistors, while the counter provides the time-base division. This arrangement permits a compact implementation of periodic timing, delayed events, or repetitive switching without requiring a microcontroller. In the system hierarchy, it is a timer and counter within clock and timing integrated circuits, which are semiconductor devices used to establish, divide, and distribute time-based signals. The core feature of the MC14541BDT is the combination of an integrated 16-stage binary counter and an external-RC oscillator. The counter architecture provides programmable division of the oscillator frequency, and the automatic power-on-reset function initializes timing when power is applied. Output-control logic allows the resulting timing signal to be observed or routed to the next stage of a system. The 3 MHz maximum clock frequency supports substantially higher timing rates than low-frequency RC-only systems while retaining simple external analog timing components. The MC14541B family is designed for applications that need repeated timing without the overhead of a digital processor. Typical uses include industrial control intervals, delayed relay activation, pump or motor duty-cycle timing, periodic sampling triggers, oscillator replacement, and embedded timing sequences. Its 18 V maximum supply voltage is useful in industrial equipment where the timer must tolerate higher control-system rail voltages, while the -55 °C to +125 °C rated range supports demanding environmental environments. Timing accuracy depends on the tolerance and temperature coefficient of the external oscillator capacitor and resistors, as well as supply and temperature stability. Component selection should therefore include worst-case tolerance rather than nominal values alone. The power-on-reset behavior establishes a defined initial count state, but it does not replace a reset function for timing an event that begins at an arbitrary point in the operating cycle. For PCB implementation, place the oscillator capacitor and timing resistors close to their associated device pins to minimize parasitic capacitance and susceptibility to EMI. Keep the oscillator loop compact and away from high-current switching nodes. The datasheet pin-description and connection diagrams should be used when assigning tracks, because the available catalog summary does not enumerate every signal name for this exact ordering code. This page combines the verified manufacturer function description, catalog electrical limits, package information, application guidance, and qualification checks into an engineering-focused view of the MC14541BDT. It also distinguishes true same-footprint replacements from related family members whose package, temperature grade, or ordering code differs.

RFQ پەیوەندی
MC14541BF - 3MHz Programmable Timer IC | onsemi | Timing
MC14541BF

MC14541BF - 3MHz Programmable Timer IC | onsemi | Timing

onsemi MC14541BF is a 3 MHz programmable timer integrated circuit with a 16-stage binary counter, integrated oscillator, automatic power-on reset, and output control logic in a 14-pin SOIC package. The MC14541BF generates a periodic output after a programmed count interval, making it suitable for timer, delay, waveform-generation, and periodic-control circuits. A programmable timer is a clock-and-timing semiconductor that counts oscillator or external clock pulses and changes an output after a selected number of counts. The MC14541BF combines that counting function with an on-chip oscillator, allowing an external resistor-capacitor network to establish the timing reference. This integration reduces the number of external timing components needed for basic interval-generation and periodic-event circuits. The device's principal features include a 16-stage binary counter, a maximum stated operating frequency of 3 MHz, automatic power-on reset, and dedicated output control logic. Its 14-pin SOIC package supports surface-mount PCB construction and automated assembly. The integrated oscillator accepts an external timing capacitor and two resistors, while the counter determines the interval between output transitions. The MC14541BF is a fixed-function timing device rather than a microcontroller or general-purpose clock generator. Its architecture is appropriate when a circuit needs predictable interval generation, recurring output transitions, or a delayed output event. The 16-stage counter provides a defined maximum count range for calculating the timing period from the oscillator frequency and selected count value. Typical uses include industrial control and automation timing, instrumentation and test-equipment trigger generation, consumer appliance delay circuits, oscillator and pulse-generation modules, and educational digital-electronics systems. The external resistor-capacitor timing network makes the frequency adjustable, while automatic power-on reset establishes a defined starting state after power is applied. PCB implementation requires close attention to oscillator component placement and signal routing. Place the external timing capacitor and resistors near the oscillator pins, keep the timing node compact, and avoid routing high-current or high-voltage switching paths beneath or beside that network. Confirm the output polarity and required count configuration against the manufacturer datasheet before relying on the circuit for a safety-related timing function. This product page combines the MC14541BF timing architecture, package information, engineering applications, comparison details, and drop-in replacement guidance. It also highlights the design checks needed to evaluate equivalent CMOS timer ICs without treating general functional similarity as proof of complete pin, timing, and electrical equivalence.

RFQ پەیوەندی
MC14541BFG - 3MHz Programmable Timer IC | onsemi
MC14541BFG

MC14541BFG - 3MHz Programmable Timer IC | onsemi

The onsemi MC14541BFG is a 3MHz programmable timer integrated circuit with a 16-stage binary counter, an integrated oscillator, automatic power-on reset, and output control logic. The device is packaged in a 14-pin SOIC surface-mount package. Its internal oscillator works with an external capacitor and two resistors, allowing the timing network to be established by the application rather than an external clock generator. A programmable timer is a clock-and-timing semiconductor that divides time or generates periodic events from an oscillator. The MC14541B belongs to the broader CMOS timer hierarchy, where an oscillator establishes the base frequency and a binary counter produces a selectable division ratio. This arrangement is useful when a circuit requires repeated timing events without dedicating a microcontroller to simple delay, pulse, or periodic-output functions. The MC14541B's principal functional characteristics include its 16-stage binary counter, 3MHz maximum listed frequency, integrated oscillator, automatic power-on reset, and output control logic. The counter architecture allows one oscillator timing network to support multiple timing divisions. Automatic power-on reset establishes a defined starting condition when power is applied, reducing the amount of external initialization required by the host circuit. Technically, the timer combines an analog oscillator interface with digital counting and control functions. The external capacitor and two timing resistors determine the oscillator's behavior, while the 16-stage counter creates the longer timing intervals required by industrial and control applications. Because the MC14541B is a CMOS logic-family device, the design belongs to a low-power digital timing category suited to control logic rather than high-current power conversion. Typical applications include periodic event generation, delayed control actions, basic pulse and timing circuits, oscillator modules, and repetitive switching sequences in industrial equipment. It can also serve as a clock source in small embedded systems where a programmable divider is sufficient and a full microcontroller would add unnecessary complexity. The 14-pin SOIC package supports conventional surface-mount assembly and compact PCB layouts. Design consideration: calculate the oscillator network and allowable divider range across the complete operating-voltage range, not only at the nominal supply voltage. Confirm that the selected output frequency, reset timing, and counter range satisfy the application before committing the external resistor and capacitor values. Use the onsemi datasheet pin-description and timing tables when assigning PCB functions and validating startup behavior. This page combines the device architecture, verified timing attributes, package information, practical application guidance, and drop-in comparison candidates with the engineering details needed to plan a replacement or evaluate the MC14541BFG for a new design.

RFQ پەیوەندی