Clock & Timing
بەرهەمەکان (970+)
ADF4117BRU - 1.2GHz Integer-N RF PLL | Analog Devices
The Analog Devices ADF4117BRU is a 1.2 GHz integer-N radio-frequency phase-locked-loop frequency synthesizer in a 16-pin TSSOP package. It is designed to generate programmable local-oscillator signals for RF upconversion and downconversion in wireless receivers and transmitters. According to the Analog Devices product page, the ADF4117 is in production and the family data sheet is Revision D. A frequency synthesizer is an electronic timing and control component that produces an output frequency derived from a stable reference frequency. An integer-N PLL belongs to the integer-N frequency synthesizer family within clock and timing ICs. Its phase-frequency detector, charge pump, reference divider, A and B counters, and dual-modulus prescaler allow a receiver or transmitter to select an RF output frequency through digital programming. The ADF4117BRU combines an input reference and programmable feedback path in a 1.2 GHz RF PLL. The verified distributor listing identifies the device as a single RF clock/frequency-synthesizer IC with one output in a 16-TSSOP package measuring 4.40 mm wide. The Analog Devices family data sheet describes low-noise digital phase-frequency detection, a precision charge pump, a programmable reference divider, programmable A and B counters, and a dual-modulus P/P+1 prescaler as the principal internal functional blocks. The device is appropriate for RF signal chains requiring a programmable local oscillator. Its 1.2 GHz maximum indicated synthesizer frequency supports wireless receiver and transmitter architectures operating within that range. The integer-N architecture simplifies frequency planning because the prescaler, A counter, and B counter determine the synthesized output relationship to the reference and feedback signals. Typical uses include wireless receiver downconversion, wireless transmitter upconversion, RF communications equipment, and other systems requiring an integrated programmable PLL. The 16-TSSOP package also allows reuse of compact RF board layouts designed for compatible members of the ADF411x family, provided the pin arrangement, frequency range, register behavior, and operating requirements are verified before substitution. When designing around the ADF4117BRU, verify the complete reference and feedback network, counter programming, loop filter, charge-pump settings, and RF output routing against the manufacturer data sheet. Ensure the selected reference frequency and prescaler produce the intended channel-plan relationship without exceeding the device's stated operating limits. This page combines the verified 1.2 GHz and 16-TSSOP identity, manufacturer family architecture, current production indication, distributor pricing reference, and same-package cross-reference information into a design-oriented resource for engineers evaluating the ADF4117BRU.
ADF4117BRUZ - 1.2 GHz Integer-N PLL | Analog Devices
Analog Devices ADF4117BRUZ is a single-channel, integer-N phase-locked-loop frequency synthesizer with a maximum RF input frequency of 1.2 GHz, a 100 MHz reference input range, and a 200 MHz output capability in a 16-pin TSSOP package. It combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus prescaler for flexible local-oscillator synthesis. A phase-locked loop, or PLL, is a feedback-controlled timing circuit that locks an output frequency to a stable reference frequency. The ADF411x family belongs to the frequency synthesizer hierarchy, where integer-N PLL synthesizers convert a reference source into programmable RF local-oscillator signals for wireless receivers and transmitters. The architecture offers integer division of the phase-detector frequency while the dual-modulus prescaler supports fractional-equivalent programming behavior within the prescaler constraints. The ADF4117 reaches a 1.2 GHz maximum RF frequency and operates from a 3 V system, with a 5.5 V maximum power-supply rating identified in the device documentation. Its programmable A and B counters, reference divider, and charge-pump output support adjustable synthesis ratios and tuning-voltage control. The part is identified as a single CMOS PLL with one synthesizer channel and one clock output function, making it suitable for compact RF signal-chain implementations. Technically, the low-noise digital phase-frequency detector compares the divided feedback signal with the divided reference. The charge pump converts the phase error into current that controls the external loop filter and tuning voltage. The resulting voltage adjusts the VCO, while the prescaler and integer counters determine the synthesis ratio. Designers must account for loop bandwidth, reference phase noise, VCO noise, filter components, and settling time when planning the RF layout. Typical uses include wireless receiver local oscillators, wireless transmitter upconversion and downconversion paths, radio equipment, and other RF systems requiring a programmable local oscillator. The device can also serve test and measurement front ends where a synthesized source is needed. Its 1.2 GHz ceiling gives it useful coverage for many RF communications bands while retaining the architecture and programming model of the wider ADF411x family. The principal design consideration is the charge-pump and VCO loop. Keep the charge-pump trace short, place loop-filter components close to the relevant pins, maintain a clean return path, and separate sensitive reference and RF routes from switching or high-current circuitry. Confirm lock range, tuning range, reference-divider settings, and settling behavior using the manufacturer’s datasheet and evaluation hardware. This product page combines the manufacturer’s ADF4117 information with package, sourcing, replacement, and design context. It identifies the verified electrical envelope, clarifies pin assignments, maps suitable RF applications, and identifies the practical limits of drop-in replacement choices for this specific 16-pin TSSOP device.
ADF4117BRUZ-RL - 1.2 GHz RF PLL Synthesizer | Analog Devices
Analog Devices ADF4117BRUZ-RL is a single-channel RF frequency synthesizer with a 1.2 GHz maximum output frequency, a programmable integer-N PLL architecture, and a 16-lead TSSOP package. The device combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus P/P+1 prescaler. It is designed to generate stable local-oscillator signals for wireless receiver and transmitter up-conversion and down-conversion stages. A frequency synthesizer is a clock-and-timing semiconductor that locks an output oscillator to a stable reference frequency. Within the broader product hierarchy, the ADF4117 is an RF PLL frequency synthesizer, part of the clock and timing IC category, and ultimately a semiconductor used for frequency generation and phase-locked-loop control. Its programmable integer-N division architecture allows a single reference oscillator to generate many output frequencies while the dual-modulus prescaler supports fractional-N operating modes through counter programming. Key features include a maximum synthesized output of 1.2 GHz, support for separate charge-pump and signal-supply voltages, and programmable A and B counters. The low-noise digital phase-frequency detector and precision charge pump form the feedback loop that compares the divided output with the reference path. A programmable reference divider supports flexible reference-frequency division, while the serial interface permits register configuration of the synthesizer and prescaler. The dual-modulus prescaler provides selectable division ratios of P or P+1. Combined with the programmable A and B counters, this architecture allows the loop divider to be adjusted without changing the external reference oscillator. A separate VP connection supports an extended tuning-voltage range when the charge-pump supply and VCO tuning requirements differ. This makes the device suitable for RF systems requiring predictable lock behavior, flexible channel spacing, and a compact implementation. Typical uses include wireless receiver and transmitter local oscillators, up-conversion and down-conversion mixers, RF test equipment, and frequency-generation modules. The 1.2 GHz maximum output covers common RF and microwave-adjacent signal chains while the integer-N architecture simplifies channel planning. Designers must account for reference noise, loop bandwidth, charge-pump current, VCO tuning sensitivity, and unwanted reference multiplication when evaluating phase-noise performance. PCB implementation requires a compact 16-lead TSSOP footprint, a stable reference source, correctly configured decoupling, and an RF-sensitive layout. Keep the reference and VCO paths short, preserve continuous ground references, and place the loop-filter components close to the synthesizer. Compare the calculated loop bandwidth with the VCO phase-noise profile so that the PLL does not add excessive close-in noise or excessive acquisition time. This page combines device-family architecture, package information, practical RF layout guidance, structured comparisons, and sourcing information to support faster component selection. It also distinguishes the exact ADF4117BRUZ-RL order code from related family members and documents which technical details require confirmation from the manufacturer datasheet before a new PCB is released.
ADF4117BRUZ-RL7 - 1.2 GHz RF PLL Synthesizer | Analog Devices
Analog Devices ADF4117BRUZ-RL7 is an RF frequency-synthesizer integrated circuit with a maximum synthesizer frequency of 1.2 GHz, packaged in a 16-pin TSSOP. It is designed for local-oscillator generation in wireless transmitters and receivers, with an indicated reference-input range of 100 MHz to 300 MHz and an example output frequency of 200 MHz. Its single-channel architecture combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus P/P+1 prescaler. A frequency synthesizer is a clock-and-timing integrated circuit that generates a stable, programmable output frequency from a reference signal. In the hierarchy of electronic components, the ADF4117 belongs to the clock generator and phase-locked-loop family, where a phase-locked loop compares a divided feedback signal with the divided reference signal. The charge pump drives the tuning voltage of a voltage-controlled oscillator, allowing integer and fractional division ratios to determine the output frequency. The ADF4117 family's key features include a 1.2 GHz maximum RF input frequency, programmable A and B counters, programmable reference division, a precision charge pump, and a dual-modulus prescaler. These features allow the device to implement a local oscillator in RF up-conversion and down-conversion paths. The 16-pin TSSOP package supports compact surface-mount layouts while providing separate connections for reference, feedback, charge-pump output, digital programming, and power. Technically, the synthesizer derives its output from a stable external reference through cascaded programmable dividers. The prescaler divides the RF feedback signal, while the A and B counters determine the required division ratio and reference divider establishes the comparison frequency. Correct lock behavior depends on stable reference routing, proper loop-filter design, controlled charge-pump current, and separation of sensitive analog and high-speed RF paths. Typical applications include wireless receiver local oscillators, transmitter up-conversion chains, RF down-conversion stages, instrumentation equipment, and communication modules. The part is particularly relevant when a compact, programmable RF clock source is required within a 1.2 GHz operating envelope. Designers must also evaluate the external voltage-controlled oscillator, loop-filter components, reference quality, and required lock time. For PCB implementation, place the reference and RF input paths on controlled-impedance routing and keep feedback traces away from charge-pump and digital programming nets. Use stable reference and loop-filter components, provide local bypass capacitance at the supply pins, and verify the external VCO tuning range before programming the synthesizer counters. These practices reduce phase-noise degradation, reference pulling, and acquisition-time variation. This product page combines the exact ADF4117BRUZ-RL7 package information with practical guidance for RF layout, loop-filter implementation, local-oscillator design, and firmware programming. It also identifies documented same-footprint alternatives and highlights the parameter checks required when changing the device without modifying the PCB.
ADF4118BRU - 3 GHz Integer-N RF PLL | Analog Devices
The Analog Devices ADF4118BRU is a single-channel, integer-N RF phase-locked-loop frequency synthesizer rated to 3.0 GHz and packaged in a 16-pin TSSOP. It is designed for wireless receiver and transmitter local oscillators, where programmable division, frequency synthesis, and phase locking must be combined in one IC. According to the Analog Devices product page, the ADF4118 is currently marked production, and the listed starting price is $2.78 as of the verified distributor search on 2026-10-23. An RF PLL is a clock-and-timing integrated circuit that locks a voltage-controlled oscillator to a stable reference frequency. The ADF4118 family combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus prescaler. This hierarchy places it under frequency synthesizers, clock and timing ICs, and semiconductor components used to control RF oscillators. The verified product classification identifies one RF PLL channel, integer-N synthesis, a maximum operating frequency of 3 GHz, and a 16-pin TSSOP package measuring 0.173 inch wide by 4.40 mm. Its programmable architecture supports local-oscillator generation in up-conversion and down-conversion sections of wireless receivers and transmitters. The precision charge-pump output drives an external loop filter, while the divided reference and counter paths establish the target synthesis ratio. The ADF4118 family architecture supports integer-N frequency synthesis by comparing the divided oscillator signal with a divided reference. Designers select divider and counter values, then calculate loop-filter components according to the Analog Devices family datasheet. This architecture is useful when a stable system reference is available and the required local-oscillator frequency must be generated with programmable division. It is not a general-purpose clock generator for applications where the output frequency is fixed and no feedback loop is required. Typical uses include wireless transmitter local oscillators, wireless receiver down-conversion, up-conversion mixers, and other RF signal chains that require synthesized frequencies. The 3 GHz capability is appropriate for RF systems whose local-oscillator requirements fall within the device range. Final suitability depends on reference frequency, prescaler settings, counter limits, loop-filter design, output buffering, and compliance with the manufacturer’s recommended operating conditions. For PCB implementation, keep the charge-pump trace and loop-filter components close to the device, maintain short RF paths, and use a controlled reference signal. The external loop filter is part of the frequency-control system; changing its resistance or capacitance can alter loop dynamics, phase margin, and spur performance. Designers should review the family datasheet and application guidance before fixing component values. This page combines the verified manufacturer classification, distributor package and pricing information, and cross-reference findings with practical selection guidance. It distinguishes confirmed data from specifications that require direct confirmation from the current Analog Devices datasheet, helping engineers identify the correct PLL family and package without confusing similar ADF4110 or ADF4154 devices.
ADF4118BRU-REEL - 3 GHz Integer-N RF PLL | Analog Devices (Tape & Reel)
The Analog Devices ADF4118BRU-REEL is a single-channel, integer-N RF phase-locked-loop frequency synthesizer rated to 3.0 GHz and packaged in a 16-pin TSSOP. It is designed for wireless receiver and transmitter local oscillators, where programmable division, frequency synthesis, and phase locking must be combined in one IC. According to the Analog Devices product page, the ADF4118 is currently marked production, and the listed starting price is $2.78 as of the verified distributor search on 2026-10-23. An RF PLL is a clock-and-timing integrated circuit that locks a voltage-controlled oscillator to a stable reference frequency. The ADF4118 family combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus prescaler. This hierarchy places it under frequency synthesizers, clock and timing ICs, and semiconductor components used to control RF oscillators. The verified product classification identifies one RF PLL channel, integer-N synthesis, a maximum operating frequency of 3 GHz, and a 16-pin TSSOP package measuring 0.173 inch wide by 4.40 mm. Its programmable architecture supports local-oscillator generation in up-conversion and down-conversion sections of wireless receivers and transmitters. The precision charge-pump output drives an external loop filter, while the divided reference and counter paths establish the target synthesis ratio. The ADF4118 family architecture supports integer-N frequency synthesis by comparing the divided oscillator signal with a divided reference. Designers select divider and counter values, then calculate loop-filter components according to the Analog Devices family datasheet. This architecture is useful when a stable system reference is available and the required local-oscillator frequency must be generated with programmable division. It is not a general-purpose clock generator for applications where the output frequency is fixed and no feedback loop is required. Typical uses include wireless transmitter local oscillators, wireless receiver down-conversion, up-conversion mixers, and other RF signal chains that require synthesized frequencies. The 3 GHz capability is appropriate for RF systems whose local-oscillator requirements fall within the device range. Final suitability depends on reference frequency, prescaler settings, counter limits, loop-filter design, output buffering, and compliance with the manufacturer’s recommended operating conditions. For PCB implementation, keep the charge-pump trace and loop-filter components close to the device, maintain short RF paths, and use a controlled reference signal. The external loop filter is part of the frequency-control system; changing its resistance or capacitance can alter loop dynamics, phase margin, and spur performance. Designers should review the family datasheet and application guidance before fixing component values. This page combines the verified manufacturer classification, distributor package and pricing information, and cross-reference findings with practical selection guidance. It distinguishes confirmed data from specifications that require direct confirmation from the current Analog Devices datasheet, helping engineers identify the correct PLL family and package without confusing similar ADF4110 or ADF4154 devices.
ADF4118BRUZ - 3 GHz Integer-N PLL | Analog Devices
The Analog Devices ADF4118BRUZ is a single-channel, integer-N radio-frequency phase-locked-loop frequency synthesizer with a maximum RF input frequency of 3 GHz, a 2.7 V to 5.5 V supply range, and a 16-lead TSSOP package. The device operates from a 4.40 mm-wide package and provides a 3-wire serial interface for programming its frequency-generation functions. A phase-locked loop, or PLL, is a feedback-controlled timing system that locks an output frequency to a stable reference. A frequency synthesizer is a PLL-based timing component used to produce programmable RF local-oscillator signals. The ADF4118 family combines a digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus prescaler for wireless receiver and transmitter signal chains. The ADF4118BRUZ reaches an RF input frequency of up to 3 GHz and operates from a 2.7 V to 5.5 V power supply. Its integer-N architecture uses programmable counters to establish the required division ratio. A three-wire serial interface supports digital control, while digital lock detect provides a status indication for system sequencing. Separate VP support allows extended tuning-voltage operation in 3 V systems. The internal architecture is designed for low-noise frequency generation in RF upconversion and downconversion paths. Its programmable reference divider and A/B counters provide flexible ratio programming, while the dual-modulus prescaler supports the required RF input division range. The 3 GHz capability makes the ADF4118BRUZ appropriate for RF communications equipment operating below that upper limit. Typical uses include wireless receiver local oscillators, wireless transmitter upconversion loops, radio-frequency instrumentation, and low-power RF communication modules. The 2.7 V minimum supply supports compact 3 V systems when the circuit topology and tuning voltage remain within the device's operating limits. The 16-lead TSSOP package also allows reuse of compact surface-mount boards rather than requiring a large through-hole footprint. When designing around the ADF4118BRUZ, calculate the required prescaler, B-counter, and A-counter values from the reference frequency and target RF input before programming the device. Keep the RF input and charge-pump loop-filter layout compact to reduce phase noise and unwanted coupling. Confirm the maximum input frequency, lock behavior, and component tolerances against the manufacturer datasheet before releasing the PCB. This page combines the manufacturer's core specifications with application guidance, practical design notes, and a compatibility-focused replacement assessment. It highlights where the ADF4118BRUZ fits RF frequency-synthesis designs and helps engineers distinguish exact package options from functionally similar PLL devices that cannot replace it on an existing PCB.
ADF4118BRUZ-RL7 - 3 GHz RF PLL Synthesizer | Analog Devices
Analog Devices ADF4118BRUZ-RL7 is a single-channel RF frequency synthesizer with a 3 GHz maximum operating frequency, housed in a 16-lead TSSOP package measuring 4.40 mm wide. The device integrates a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, 5-bit A and B counters, and a dual-modulus P/P+1 prescaler. It is designed to generate the local-oscillator signal required by wireless receiver and transmitter up-conversion and down-conversion paths. A frequency synthesizer is a phase-locked-loop, or PLL, component that locks an output frequency to a stable reference. In the ADF4118, the programmable dividers and counters determine how the phase-frequency detector compares the divided feedback signal with the reference. When the feedback and reference agree, the charge pump corrects the output until the loop reaches lock. This architecture provides programmable RF output for communication equipment while requiring an external reference, loop filter, voltage-controlled oscillator, and RF output network. The ADF4118 family's principal features include a 3 GHz operating ceiling, one synthesizer channel, a digital phase-frequency detector, a precision charge pump, and programmable reference, A-counter, and B-counter functions. The dual-modulus prescaler supports fractional-N synthesis techniques by allowing the programmable counters to represent ratios that cannot be produced through integer division alone. The low-noise phase-frequency detector helps establish low phase noise in the synthesized output, while the charge pump controls loop current and correction behavior. The ADF4118BRUZ-RL7 is differentiated by its 16-lead TSSOP surface-mount package and the -RL7 production configuration. The package is suitable for automated assembly and compact RF modules. As with any high-frequency PLL, performance depends on the external reference source, loop filter, voltage-controlled oscillator, power-supply layout, and impedance-matched PCB traces. The datasheet's application and pin-description tables should govern the final reference design rather than assumptions based only on the family-level architecture. Typical uses include wireless receiver and transmitter local oscillators, up-converters and down-converters, RF instrumentation, communication transceivers, and frequency-generation modules. The synthesizer can support programmable channels where one reference drives multiple selectable output frequencies. Component selection should include the required output range, reference frequency, prescaler range, channel spacing, phase-noise target, tuning bandwidth, and regulatory requirements for the finished equipment. Keep the reference and feedback routes short and impedance controlled, and place the loop-filter components near the relevant device pins. Use a clean, well-decoupled supply because supply ripple can degrade phase noise and spur performance. A careful grounding strategy and short RF output path are equally important; the digital programming interface and sensitive RF nodes should not share uncontrolled return-current paths. This product page combines the manufacturer architecture and package information with practical PLL design guidance, verified source links, and a conservative review of replacement options. It helps engineers identify the correct ADF4118 configuration, distinguish true drop-in devices from packaging-only variants, and plan RF layout, loop-filter implementation, sourcing, and qualification.
ADF4118YRUZ - 3.0 GHz Integer-N PLL | Analog Devices
Analog Devices ADF4118YRUZ is a single-channel, integer-N, 3.0 GHz phase-locked-loop frequency synthesizer in a 16-lead surface-mount package. It is designed to generate local-oscillator signals for wireless receiver and transmitter upconversion and downconversion paths. The frequency synthesizer integrates a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus prescaler identified as P/(P+1). Its integer-N architecture simplifies frequency planning by making the feedback-divider division ratio an integer and avoiding the fractional-N interpolation circuitry required by fractional synthesizers. A phase-locked loop is a feedback-control system that locks an output oscillator phase to a reference signal. The ADF4118 compares its divided feedback output with a reference through the phase-frequency detector. The detector and charge pump convert phase and frequency error into a correction voltage for the internal voltage-controlled oscillator, or VCO. In an RF transceiver, this closed-loop arrangement produces a stable local-oscillator signal while suppressing phase noise and reference-multiplication effects. The device therefore belongs to the frequency-synthesizer and clock-and-timing hierarchy before broader categories such as RF signal-generation ICs and semiconductor devices. The manufacturer's ADF4116, ADF4117, and ADF4118 family documentation identifies programmable reference division, A-counter and B-counter functions, and a dual-modulus prescaler as central features. These controls let a designer establish the relationship among the reference frequency, prescaler, counters, and generated RF output. For the ADF4118YRUZ, the 3.0 GHz headline frequency makes the device relevant to radio systems operating below or around that upper limit, including wireless transceivers and test equipment. The exact operating supply, current consumption, noise, lock-time, and counter ranges should be confirmed from the manufacturer datasheet before final circuit release. Typical uses include wireless receiver local oscillators, transmitter upconversion and downconversion chains, industrial RF test equipment, and communication modules requiring programmable frequency generation. In a typical design, the reference oscillator feeds the reference divider and PFD, while the VCO output is divided through the prescaler and counters before being returned to the loop. Correct charge-pump current, loop-filter values, VCO gain, and reference frequency determine lock behavior and phase noise. A key design consideration is loop stability. Keep the feedback divider, loop filter, and RF output path compact, use stable reference and decoupling components, and account for charge-pump mismatch when the loop is driven into cycle slipping. This page combines the verified product identity, manufacturer family description, sourcing guidance, and engineering-oriented design guidance to support component selection before a schematic is released. For purchasing, stock, and lead-time confirmation, use the Request a Quote form on this page and specify the exact ADF4118YRUZ ordering code. Do not substitute a different package suffix without checking land pattern, pin functions, exposed-pad requirements, and production status against the manufacturer datasheet.
ADF4150BCPZ - 4.4 GHz Fractional-N PLL | Analog Devices
The Analog Devices ADF4150BCPZ is a fractional-N and integer-N radio-frequency phase-locked-loop frequency synthesizer with an operating input frequency range of 10 MHz to 4 GHz, a maximum synthesizer frequency of 4.4 GHz, and a 750 MHz output reference capability. It is packaged in a 24-lead WFQFN with exposed pad, also identified as a 24-pin LFCSP, for surface-mount RF and timing applications. A phase-locked loop, or PLL, is a frequency-control system in which a phase detector compares a divided feedback signal with a reference signal and drives a voltage-controlled oscillator through a loop filter. The ADF4150 provides the digital divider, phase detector, charge pump, reference and control registers required to implement a fractional-N or integer-N synthesizer. It requires an external VCO, loop filter, and reference source, allowing the RF tuning range and loop performance to be tailored to the target system. Principal features include support for both fractional-N and integer-N operation, programmable RF output division by 1, 2, 4, 8, or 16, and software compatibility with the ADF4350 family. The 24-WFQFN exposed-pad package supports compact surface-mount layouts and provides a central thermal connection. The digital control interface permits operating parameters to be configured through a serial bus rather than fixed hardware settings. The device divides the feedback signal into the phase detector and compares that divided signal with the external reference. Its charge pump drives the external loop filter, which controls the tuning voltage applied to the external VCO. Fractional-N operation enables a rational division ratio that can represent frequencies with a finer effective resolution than an integer divider alone, while integer-N operation provides a conventional integer-ratio configuration. Typical applications include wireless communication infrastructure, test and measurement equipment, clock generation for RF systems, radar-related signal chains, industrial instrumentation, and local oscillator generation. The part is especially useful when a design needs programmable fractional frequency synthesis while retaining flexibility over the external VCO and loop-filter implementation. Design should account for the external VCO, loop filter, reference source, output matching, decoupling, and exposed-pad thermal design. Use the ADF4150 datasheet pin-description and test-circuit information when assigning traces, grounding the exposed pad, and selecting component values around the PLL loop. Validate lock range, phase noise, reference spur levels, and temperature performance in the final board-level design. This page organizes the device specifications, sourcing information, drop-in alternatives, application guidance, and engineering design considerations in one concise engineering reference. It is intended to accelerate component selection while keeping the final design anchored to the Analog Devices product documentation.
ADF41513BCPZ - 26.5 GHz Fractional-N PLL Synthesizer | Analog Devices
Analog Devices ADF41513BCPZ is an integer-N and fractional-N PLL frequency synthesizer capable of generating local-oscillator signals as high as 26.5 GHz. It uses a high-performance SiGe BiCMOS process and is packaged in a 24-lead WFQFN package with an exposed pad. Its normalized phase-noise floor is -235 dBc/Hz, while the phase-frequency detector supports operation up to 250 MHz in integer-N mode and 125 MHz in fractional-N mode. A PLL frequency synthesizer belongs to the clock-and-timing IC hierarchy, where it combines a phase-locked loop, programmable frequency dividers, a phase-frequency detector, and a voltage-controlled oscillator with an integrated or external resonator. In a wireless transmitter or receiver, the ADF41513 can synthesize coherent local-oscillator signals needed by upconversion and downconversion stages. Its fractional-N operation supports fine frequency resolution while retaining high reference-channel rates for improved phase-noise and spur performance. The device supports both integer-N and fractional-N synthesis, giving designers flexibility between exact integer multiplication and fine fractional frequency control. The maximum PFD rate is 250 MHz in integer-N mode and 125 MHz in fractional-N mode. Its -235 dBc/Hz normalized phase-noise floor is particularly useful in receiver and transmitter signal chains where close-in phase noise can affect modulation fidelity, receiver selectivity, and transmitter signal quality. ADF41513BCPZ is used for wireless receiver and transmitter local oscillators, microwave downconversion, microwave upconversion, test and measurement equipment, and instrumentation requiring programmable RF output. The manufacturer describes the family as an ultralow-noise frequency synthesizer capable of operating as high as 26.5 GHz. The principal PCB concern is high-frequency isolation. The manufacturer datasheet notes that reference-switching noise can feed through the RFINA or RFINB pins and return to the VCO, potentially producing reference spurs as high as -90 dBc. Keep reference and VCO routing separated, use controlled impedance, and preserve a continuous ground return beneath RF traces. This product page combines the verified manufacturer specifications with sourcing guidance, replacement analysis, and practical RF layout considerations. The ADF41513BCPZ is appropriate when an adjustable fractional-N synthesizer is required, but the complete pin description, programming interface, and detailed electrical limits must be taken from the Analog Devices ADF41513 datasheet before schematic capture and PCB release.
ADF4151BCPZ - 3.5 GHz Fractional-N PLL | Analog Devices
The Analog Devices ADF4151BCPZ is a 1-channel fractional-N or integer-N phase-locked-loop frequency synthesizer with an operating frequency up to 3.5 GHz, supplied in a 32-lead WFQFN exposed-pad CSP package. It requires an external voltage-controlled oscillator, loop filter, and reference frequency to implement a complete frequency synthesizer. A phase-locked loop, or PLL, is a feedback-controlled timing circuit that locks an output oscillator to a stable reference. Within the broader semiconductor hierarchy, the ADF4151 is a clock-generation and timing IC, specifically a frequency synthesizer. Its fractional-N and integer-N operating modes provide programmable division while allowing the associated VCO to generate a precisely controlled high-frequency output. The principal features include support for both fractional-N and integer-N synthesis, a 1-channel architecture, and operation with a 10 MHz input reference according to the product listing. The ADF4151BCPZ is also footprint- and software-compatible with the ADF4350 family, as identified by Analog Devices, making it useful when an existing board architecture must support either device family. Its exposed-pad package supports improved thermal dissipation when the PCB provides an effective thermal path. The synthesizer architecture separates frequency generation from the RF output stage. The ADF4151 generates the control information needed to drive an external VCO, while an external loop filter converts the charge-pump and phase-detector signals into a control voltage. This architecture allows the VCO, loop bandwidth, output power, and tuning range to be selected for the intended RF band rather than being fixed inside the synthesizer IC. Typical applications include wireless communication infrastructure, test and measurement equipment, industrial radio links, frequency-modulated signal generation, and local-oscillator synthesis for RF front ends. For systems requiring continuous phase adjustment, the fractional-N mode offers finer division ratios than integer-N operation. Integer-N mode is useful where simpler integer ratios, deterministic division behavior, or conventional loop-filter design are priorities. The principal design consideration is closing the PLL loop correctly. The reference source, charge-pump current, loop filter, VCO tuning gain, and expected phase noise must be evaluated together. Place the exposed pad over a low-impedance thermal and ground structure, follow the reference and charge-pump layout guidance in the manufacturer datasheet, and keep sensitive feedback and control traces away from high-current switching nodes. This page consolidates the verified product characteristics, compatible device options, application guidance, and practical PCB considerations into one engineering-focused reference for evaluating the ADF4151BCPZ in fractional-N and integer-N frequency-synthesizer designs.
ADF4151BCPZ-RL7 - 3.5GHz Fractional-N PLL | Analog Devices
The Analog Devices ADF4151BCPZ-RL7 is a fractional-N or integer-N phase-locked-loop frequency synthesizer rated for operation up to 3.5 GHz and housed in a 32-lead WFQFN exposed-pad package. It requires an external voltage-controlled oscillator, loop filter, and reference source, giving the designer control over the RF output stage while the integrated synthesizer handles phase detection, programmable division, and frequency control. A phase-locked loop, or PLL, is a feedback-control system that locks an output frequency to a stable reference. A fractional-N frequency synthesizer extends this arrangement by dividing the reference in integer and fractional increments. In the broader product hierarchy, the ADF4151 is a clock and timing IC, a PLL frequency synthesizer, and ultimately a semiconductor frequency-control device. This division places it between a reference clock and an external VCO. The device supports both fractional-N and integer-N synthesis, allowing fractional operation for fine frequency resolution or integer operation for simpler channel planning. Its 3.5 GHz upper-frequency designation makes it relevant to microwave and RF systems, while the external-VCO architecture supports designs in which the RF oscillator technology, tuning range, or output power is determined separately from the synthesizer IC. For integration, the ADF4151 operates with an external VCO, an external loop filter, and a reference frequency. The loop filter establishes loop bandwidth, phase margin, and rejection of reference or VCO phase noise. Digital programming controls synthesis parameters through the device interface. The manufacturer identifies the ADF4151 as footprint- and software-compatible with the ADF4350, which is important when evaluating PCB reuse and register-level migration. Typical uses include wireless infrastructure, microwave radio links, test and measurement instruments, radar and electronic-warfare systems, and other RF systems requiring programmable frequency generation. In each case, the external VCO permits selection of an appropriate tuning range and output power, while the synthesizer establishes phase-lock and channel-selection behavior. A critical implementation consideration is that the PLL performance depends on the complete loop rather than the IC alone. Select the reference, VCO, loop filter, charge-pump settings, and output-divider configuration together. Preserve short return paths and provide adequate thermal coupling through the exposed pad when programming increases operating activity or ambient temperature. This product page combines the verified device identity and package information with practical PLL design guidance, same-footprint alternatives, application guidance, and a parameter-by-parameter comparison. It is intended to help engineers identify whether the ADF4151 architecture and its external-VCO approach fit a microwave frequency-synthesis design.
ADF4153ABCPZ - 4GHz Fractional-N PLL | Analog Devices
Analog Devices ADF4153ABCPZ is a 4 GHz fractional-N frequency synthesizer used to create local-oscillator signals in wireless receiver and transmitter upconversion and downconversion paths. The device combines a low-noise digital phase-frequency detector, a precision charge pump, and a programmable reference divider. A sigma-delta fractional interpolator enables programmable fractional-N operation, supporting flexible frequency planning where a conventional integer-N synthesizer would require an impractical division ratio. The component is packaged in a 20-WFQFN exposed-pad CSP package. A fractional-N frequency synthesizer is a phase-locked-loop device that synthesizes an adjustable output frequency from a stable reference. In a wireless transceiver, a local oscillator drives mixers in the RF signal path. The ADF4153A family combines integer-N and fractional-N synthesis in one RF PLL, while its programmable reference divider and low-noise phase detector support the phase-noise and spur trade-offs inherent in fractional-N architectures. The result is a flexible frequency-generation block suitable for RF systems where the required channel spacing and output range must coexist within a compact circuit. The ADF4153ABCPZ reaches an upper operating frequency of 4 GHz. Its fractional-N architecture provides a practical way to obtain fine frequency increments without relying solely on integer division. Designers must still account for fractional spurs, reference phase noise, loop bandwidth, charge-pump settings, and filtering requirements. The PFD, charge pump, reference divider, and sigma-delta fractional interpolator form the core control path, while external passive and RF networks provide reference conditioning, loop filtering, and impedance matching. Typical uses include wireless receiver and transmitter local oscillators, upconversion and downconversion sections, and other RF communication systems requiring programmable frequency generation. The same synthesis principles apply in instrumentation, test equipment, and frequency-generation subsystems, although each application needs its own phase-noise, spur, tuning-speed, and output-drive evaluation. The manufacturer product page specifically identifies wireless receiver and transmitter local oscillators as core applications. A critical implementation step is to preserve the reference-signal quality presented to the synthesizer because reference phase noise and unwanted modulation can propagate into the generated output. The exposed thermal pad also requires a deliberate PCB thermal strategy, including suitable copper and via placement, so that heat from the synthesizer is removed effectively. Loop-filter component selection should be completed against the intended channel spacing and phase-noise target rather than by copying values without checking fractional spur behavior. This page summarizes the verified product identity, RF synthesizer function, frequency capability, package, and family alternatives. It also adds application guidance, drop-in-replacement assessment, and engineering design notes intended to help engineers evaluate the ADF4153ABCPZ before committing it to an RF board design.
ADF4153ABRUZ - 4 GHz Fractional-N RF Synthesizer | Analog Devices
The Analog Devices ADF4153ABRUZ is a fractional-N radio-frequency frequency synthesizer with a 4 GHz maximum synthesis frequency, a 10 MHz to 4 GHz input range, and a 16-lead TSSOP package measuring 0.173 inch, or 4.40 mm, in width. Designed for RF local-oscillator generation, it supports wireless transmitter and receiver signal chains that require programmable frequency synthesis with fractional division. A fractional-N frequency synthesizer is a phase-locked-loop device that generates a stable output frequency by phase-locking a voltage-controlled oscillator to a reference source. In the wider semiconductor hierarchy, the ADF4153 belongs to the clock and timing IC category, then to phase-locked loops and frequency synthesizers. This architecture supports rational frequency ratios that allow a desired RF output to be produced with a reference frequency that may not divide it exactly. The ADF4153ABRUZ combines a low-noise digital phase-frequency detector, precision frequency dividers, and fractional-N control logic for programmable RF synthesis. Its stated operating input span extends from 10 MHz to 4 GHz, while the maximum synthesis frequency is 4 GHz. The 16-lead TSSOP package supports compact surface-mount implementation, and the narrow 4.40 mm package width is useful in space-constrained radio modules. The fractional-N architecture is particularly relevant to local oscillators in wireless receivers and transmitters. It allows the phase detector and loop filter to operate at a comparatively low reference-related frequency while maintaining a high synthesized output. Design evaluation must account for loop-filter bandwidth, phase noise, reference purity, integer and fractional divider settings, and the required output frequency. Those operating details should be configured with the manufacturer’s frequency-planning and register settings. Typical uses include cellular and wireless infrastructure, radio transceivers, microwave downconverters, and upconverters. The device can also serve closed-loop RF systems where the local oscillator must track a programmable channel plan. Its frequency ceiling makes it applicable to 4 GHz-class signal paths when the selected divider, reference, and loop-filter settings support the required channel spacing. Place decoupling capacitors close to the supply pins and route the reference and feedback paths as controlled-impedance traces with minimal parasitic coupling. Validate the phase-noise and spur performance across operating temperature because fractional-N operation, reference multiplication, and loop-filter settings influence the resulting spectrum. This product page combines the manufacturer’s device description, exact-ordering information, drop-in candidates, and application-specific engineering guidance. It also distinguishes confirmed package and frequency facts from parameters that require validation in the ADF4153 datasheet and application-specific reference design.
ADF4153BCP - 4 GHz Fractional-N Synthesizer | Analog Devices
The Analog Devices ADF4153BCP is a fractional-N frequency synthesizer covering 500 MHz to 4 GHz, operating from a 3.3 V supply and packaged in a 20-lead LFCSP surface-mount package. It combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, and Sigma-Delta fractional interpolator for programmable fractional-N division. A fractional-N frequency synthesizer is a clock-generation IC that synthesizes an output frequency locked to an external reference while allowing non-integer division ratios. Within the broader semiconductor hierarchy, it is a PLL-based frequency synthesizer, a clock-and-timing IC, and a power-management-adjacent RF timing component used to generate stable local-oscillator signals in receiver and transmitter chains. The ADF4153 supports RF bandwidths from 500 MHz to 4 GHz and includes selectable 4/5 and 8/9 dual-modulus prescalers. Programmable charge-pump currents support loop-filter optimization, while the 3-wire serial interface provides register-based control of synthesis functions. The separate VP connection allows the tuning-voltage supply to be extended, making the device suitable for RF systems requiring elevated VCO tuning voltages. Its architecture uses a low-noise digital phase-frequency detector to compare the divided feedback signal with the divided reference. A precision charge pump drives the loop-filter voltage, while the Sigma-Delta fractional interpolator enables fractional division without changing the external reference frequency. The result is flexible frequency planning for RF transmitters, receivers, instrumentation, and communication equipment. Typical uses include wireless receiver and transmitter local oscillators, upconversion and downconversion chains, RF test equipment, and frequency-generation modules. The fractional-N architecture is particularly useful when the desired channel spacing cannot be obtained conveniently through integer-N division. The 4 GHz upper operating limit supports high-band RF designs, while the 500 MHz lower limit covers cellular, microwave, and test-signal applications. PCB layout is critical because the ADF4153's phase-noise and spur performance depends on isolation between the RF input, VCO, reference, charge-pump output, and sensitive analog supply pins. Keep the VCO away from the reference input to avoid board-level reference-noise feedthrough, and place decoupling and loop-filter components close to their associated pins. This page combines verified Analog Devices product information, distributor pricing, package details, candidate drop-in alternatives, and practical design guidance to support faster component selection, PCB compatibility review, and RF design planning.
ADF4153BCPZ - 4 GHz Fractional-N PLL Synthesizer | Analog Devices
The Analog Devices ADF4153BCPZ is a fractional-N frequency synthesizer IC with a maximum RF input frequency of 4 GHz, supplied in a 20-pin VFQFN exposed-pad package. It is designed for precision local-oscillator generation in wireless receiver and transmitter signal chains, combining a low-noise digital phase-frequency detector, a precision charge pump, and programmable fractional-N frequency synthesis. The device operates from a 3.3 V supply according to the manufacturer datasheet. A fractional-N frequency synthesizer is a phase-locked-loop, or PLL, frequency generator that uses a divided reference clock and programmable integer and fractional divider values. Its role in the hierarchy of electronic timing components is specific: it converts a stable reference frequency into a precisely programmable RF output while maintaining phase lock to that reference. This makes the ADF4153 suitable when an RF system needs local-oscillator or modulation frequencies that can be changed digitally while retaining frequency stability derived from the external reference. The ADF4153BCPZ supports RF synthesis up to 4 GHz and includes programmable fractional-N operation. Key benefits include the integration of the phase detector, charge pump, reference divider, integer-N divider, fractional-N divider, and local-oscillator output in one compact IC. Its 20-pin exposed-pad package supports surface-mount assembly and provides a thermal path through the exposed pad. The package is suitable for RF transceiver, upconversion, and downconversion designs operating close to the device's upper RF frequency limit. The internal architecture uses a low-noise digital phase-frequency detector and precision charge pump to support low-noise RF clock generation. The reference input is divided by a programmable reference divider, while the feedback path applies integer-N and fractional-N division to establish the synthesis ratio. Designers must follow the register map and sequencing procedure in the manufacturer datasheet because divider values, charge-pump current, reference frequency, and prescaler selection determine phase noise and spur performance. Typical uses include wireless receiver local oscillators, wireless transmitter local oscillators, upconversion and downconversion sections, instrumented RF measurement systems, and communications equipment requiring programmable RF frequency generation. For systems near 4 GHz, board layout is especially important because the reference, charge-pump, divider, and RF feedback paths can affect phase noise and spurious performance. Correct impedance-controlled routing, a clean power supply, and short high-frequency paths should be treated as core layout requirements rather than optional refinements. A key design consideration is power delivery to the exposed pad. Follow the manufacturer datasheet's land pattern and thermal-pad connection guidance, and verify that the PCB provides adequate copper for both electrical grounding and heat removal. Avoid long traces between the reference source and the RF input, and keep sensitive control or digital programming interfaces away from high-current and RF return paths. This page organizes the verified product information with practical architecture guidance, application use cases, lifecycle context, sourcing answers, and a conservative replacement assessment. The comparison focuses on electrically meaningful device differences rather than treating different packaging codes as separate engineering alternatives.
ADF4153BCPZ-RL7 - 4 GHz Fractional-N RF Synthesizer | ADI
The Analog Devices ADF4153BCPZ-RL7 is a 4 GHz fractional-N frequency synthesizer with one RF output, a three-wire serial interface, and a 20-VFQFN exposed-pad CSP package. It operates from a 2.7 V to 3.3 V supply and supports an external reference source over a -40 °C to +85 °C temperature range. A fractional-N frequency synthesizer belongs to the PLL-based clock and timing IC category. It locks an output oscillator to a stable reference frequency while allowing fractional division ratios between integer settings. This architecture combines integer-N frequency synthesis with a Sigma-Delta fractional interpolator, enabling fine frequency resolution without requiring an exceptionally high reference frequency. The ADF4153 family integrates these functions with low-noise digital phase-frequency detection, a precision charge pump, programmable reference division, and a programmable feedback divider. Key features include operation up to 4 GHz, fractional-N synthesis, a digital lock indicator, selectable charge-pump currents, and a three-wire digital interface. The wide synthesis range supports RF local-oscillator generation for communications equipment, while fractional division permits narrow channel spacing and precise tuning. A low-noise phase-frequency detector and precision charge pump help establish low phase noise and accurate lock performance in demanding RF signal chains. The Sigma-Delta fractional interpolator generates fractional divider values while its digital section controls the reference and feedback paths. Programmable charge-pump current allows loop bandwidth and phase-error performance to be tuned according to reference frequency, channel spacing, and filter requirements. Designers should use the manufacturer’s loop-filter design guidance rather than treating the fractional-N architecture as a universal fixed filter, because loop dynamics and reference spurs depend strongly on the selected divider ratios. Typical uses include wireless transmitter and receiver local oscillators, microwave downconversion, upconversion, frequency-agile test equipment, and closed-loop RF signal-generation systems. The device is also appropriate for instrumentation requiring precise local-oscillator tuning, phase-locked signal references, or an output locked to an external frequency standard. A critical design consideration is the exposed thermal pad beneath the 20-VFQFN package. Place the pad over a continuous ground-plane area and follow the datasheet’s land-pattern and thermal-via recommendations. The power, reference, and RF paths also require careful grounding and isolation so reference-divider noise, supply coupling, and unintended feedback do not degrade phase noise or spur performance. This product page combines the manufacturer’s architectural information, package and interface details, sourcing context, parameter comparisons, and practical implementation guidance. It is intended to help engineers evaluate the ADF4153BCPZ-RL7, identify temperature-grade or related-family alternatives, and plan a robust fractional-N PLL layout before committing the design to production.
ADF4153BRU - 4 GHz Fractional-N PLL | Analog Devices
The Analog Devices ADF4153BRU is a fractional-N frequency synthesizer with a documented input range of 10 MHz to 4 GHz and a 4 GHz maximum synthesizer frequency, housed in a 16-pin TSSOP package measuring 0.173 inch, or 4.40 mm, in width. It is designed for local-oscillator and frequency-conversion functions in wireless receivers and transmitters. The device combines a low-noise digital phase-frequency detector, a precision charge pump, a programmable reference divider, and a sigma-delta fractional-N interpolator. A fractional-N frequency synthesizer is a clock-and-timing integrated circuit that generates an output frequency by phase-locking a voltage-controlled oscillator to a stable reference. The fractional-N architecture permits programmable fractional division, while the phase-frequency detector and charge pump compare the divided feedback signal with the reference. This places the ADF4153BRU within the broader PLL, frequency synthesizer, clock-generation, and power-management-supported signal-chain hierarchy. The principal verified feature set includes fractional-N operation, a PLL architecture, an RF input range of 10 MHz to 4 GHz, a 4 GHz upper frequency, and a 16-pin TSSOP package. The manufacturer describes the sigma-delta fractional interpolator as the element that enables programmable fractional-N division. These characteristics suit communications equipment requiring synthesized RF signals and programmable frequency relationships between a reference source and an external voltage-controlled oscillator. The ADF4153BRU uses a precision charge pump and low-noise digital phase-frequency detector to support the phase-locked loop. The programmable reference divider lets the reference relationship be adjusted for a given system architecture. The supplied manufacturer documentation also warns that reference-switching noise can couple from the RF input back toward the VCO and create reference spurs, potentially reaching -90 dBc; this makes physical separation and controlled PCB routing important. Typical uses include wireless receiver local oscillators, wireless transmitter upconversion and downconversion stages, RF communication equipment, test and measurement instruments, industrial RF systems, and instrumentation requiring programmable fractional frequency synthesis. In each case, the component serves as the programmable phase-locking element rather than a complete standalone RF signal source because an external VCO and loop-filter implementation are central to this device class. PCB implementation should keep the VCO separated from the reference input to minimize the documented feedthrough path. Designers should also use short, controlled reference and feedback routes, place decoupling close to the supply pins, and follow the manufacturer datasheet for loop-filter and charge-pump component values. These measures help limit reference spurs while preserving the fractional-N synthesizer's intended frequency accuracy and phase-noise behavior. This page consolidates the verified manufacturer specifications, distributor availability, package information, purchasing context, and practical layout guidance for ADF4153BRU. It also separates confirmed drop-in information from unverified functional substitutes so engineers can assess replacement risk without assuming that similar fractional-N synthesizers share the same footprint.
ADF4153BRUZ - 4GHz Fractional-N PLL | Analog Devices
Analog Devices ADF4153BRUZ is a 4 GHz fractional-N frequency synthesizer IC with one RF output, packaged in a 16-pin TSSOP measuring 4.40 mm in width. It is designed to generate local-oscillator signals in wireless receiver and transmitter upconversion and downconversion paths, while its external reference interface supports programmable frequency synthesis from a stable off-chip reference. A fractional-N frequency synthesizer is a PLL-based timing and RF signal-generation device that combines integer-N division with a sigma-delta fractional interpolator. This enables fine frequency resolution without requiring an extremely high reference frequency. Within the product hierarchy, the ADF4153 belongs to the phase-locked-loop family, the clock and timing IC category, and ultimately the broader semiconductor category used for programmable RF and clock generation. The principal identifiers are a maximum synthesizer frequency of 4 GHz, one RF output, fractional-N operation, and a 16-pin TSSOP package. The device includes a low-noise digital phase-frequency detector, a precision charge pump, and a programmable reference divider. These blocks establish the phase-error signal, control the charge injected into the loop filter, and divide the reference frequency presented to the synthesizer core. The sigma-delta fractional interpolator permits programmable fractional-N division for applications requiring precise channel spacing. The ADF4153 is particularly useful when a system needs a locally generated RF carrier with adjustable output frequency. Its fractional-N architecture is applicable to wireless transceivers, test equipment, instrumentation, and communication infrastructure. An external reference and loop-filter implementation also let engineers tune phase noise, reference-divider settings, channel spacing, and lock behavior to the requirements of a particular system rather than relying on a fixed internal timebase. Typical applications include wireless receiver and transmitter local oscillators, RF upconversion and downconversion chains, laboratory frequency generators, and phase-locked test equipment. In a communications design, the synthesizer can generate the carrier or local-oscillator reference used by mixer stages. In instrumentation, programmable division and fractional-N operation can support frequency selection across a wide operating range while retaining compact PLL implementation. The principal design consideration is loop-filter realization. Its component values determine reference-divider settings, fractional-N behavior, loop bandwidth, settling time, and phase-noise performance. Follow the ADF4153 manufacturer datasheet for the recommended reference-divider and charge-pump settings, and validate filtering and spur performance at the intended carrier and reference frequencies before releasing the PCB design. This product page combines the device identity, package information, verified source links, application guidance, comparison parameters, and practical design notes. It supports faster part selection while keeping the engineer’s focus on the electrical behavior and layout decisions that determine fractional-N PLL performance.
ADF4153BRUZ-RL7 - 4GHz Fractional-N Synthesizer | Analog Devices
The Analog Devices ADF4153BRUZ-RL7 is a fractional-N frequency synthesizer with a 4 GHz maximum synthesis frequency, designed for wireless receiver and transmitter local-oscillator architectures. The device is packaged in a 16-lead TSSOP with a 4.40 mm body width. Its fractional-N architecture combines integer frequency division with programmable fractional feedback to support fine frequency resolution while preserving phase-locked-loop operation for RF signal generation and conversion. A fractional-N frequency synthesizer is a phase-locked-loop device that generates a stable, programmable output frequency from a reference clock. Within the broader hierarchy, it belongs to clock and timing ICs, frequency synthesizers, phase-locked loops, and power-management-independent RF signal-chain devices. The ADF4153 family is used where an RF system requires local-oscillator generation for upconversion, downconversion, modulation, demodulation, or other frequency-conversion functions. The ADF4153 integrates a low-noise digital phase-frequency detector, a precision charge pump, and a programmable reference divider. Its fractional-N feedback uses a sigma-delta digital-to-analog converter to modulate the feedback divider and generate fractional frequency steps. This architecture helps improve phase-noise and spur performance compared with conventional integer-N synthesis while retaining programmable output-frequency control through a serial interface. The 4 GHz operating capability makes the ADF4153 suitable for RF sections operating below that ceiling. Exact phase-noise, reference-input, output-drive, lock-time, channel-spacing, and current-consumption limits should be taken from the manufacturer datasheet for the selected temperature and production variant. Because these limits depend on divider settings, reference frequency, PFD frequency, and loop-filter values, system-level calculations require the complete operating configuration rather than the maximum synthesizer frequency alone. Typical uses include wireless receiver local oscillators, wireless transmitter upconverters, instrumentation and test equipment, and frequency-generation modules. In each application, the device establishes the tunable reference used by a mixer or downstream RF stage. Selection should account for required output frequency, channel spacing, reference frequency, permitted spur and phase-noise levels, loop bandwidth, and the register-control interface implemented by the host processor or FPGA. PCB implementation requires careful treatment of the power, ground, reference, and RF connections. Keep the power-supply and ground paths short, place decoupling components close to their associated pins, and follow the package-specific land pattern in the manufacturer datasheet. The reference and feedback paths should be routed away from high-energy RF and switching nodes to reduce unwanted coupling. This page combines the manufacturer device description, exact 4 GHz and 16-TSSOP identifiers, sourcing records, package guidance, and a restricted drop-in comparison that focuses on genuine pin-compatible ADF4153-family choices rather than merely similar synthesizer functions.
ADF4153YCPZ - 4 GHz Fractional-N PLL Synthesizer | Analog Devices
Analog Devices ADF4153YCPZ is a fractional-N frequency synthesizer with RF bandwidth to 4 GHz, programmable fractional modulus, and a clock output for precision frequency generation. It operates from a 3.3 V power supply with a 2.7 V to 3.3 V supply range and is packaged in a 20-lead VFQFN with an exposed pad. The Y-grade version supports operation from -40°C to +125°C. Designed for local oscillators in wireless transmitters and receivers, the device combines a low-noise digital phase-frequency detector, a precision charge pump, and a programmable reference divider. A fractional-N frequency synthesizer is a clock-generation and timing IC that locks a voltage-controlled oscillator to a stable reference frequency while dividing the feedback signal into programmable integer and fractional ratios. Its role in the broader hierarchy is fractional-N PLL → phase-locked loop → clock generator → clock and timing IC. This architecture allows fine frequency resolution without requiring an extremely high reference frequency, making the ADF4153 useful in RF systems that demand flexible channel spacing and precise tuning. The principal features include RF bandwidth to 4 GHz, a 3.3 V supply, a separate charge-pump voltage supply that permits an extended tuning-voltage range, programmable fractional modulus, and programmable charge-pump current. Differential reference and feedback inputs are indicated by the device specifications, while the synthesizer supplies a single-ended clock output. The 20-VFQFN exposed-pad package provides a compact surface-mount solution and exposes a thermal connection beneath the device. Internally, the phase-frequency detector compares the divided feedback signal with the divided reference. The charge pump converts phase error into a current that controls the external voltage-controlled oscillator. Programmable integer and fractional feedback ratios determine the synthesized output. The fractional-N architecture supports practical channel spacing without requiring every channel to be generated by changing the reference frequency, although phase noise, reference spurs, and VCO tuning range remain critical system-level considerations. Typical uses include wireless receiver and transmitter local oscillators, upconversion and downconversion sections, radio equipment, communication infrastructure, and test systems requiring programmable RF frequencies. The ADF4153 is particularly appropriate when the design needs fractional channel spacing while retaining a 4 GHz maximum RF bandwidth. It can also be used as the frequency-setting element in phased-array, microwave, and instrumentation systems when combined with a suitable external VCO. Layout is a central implementation concern because reference-switching noise can feed through the RF input and modulate the VCO. Keep the VCO physically separated from the reference path, use a compact ground plane, route sensitive nodes away from digital and switching-current paths, and follow the pin-description and layout guidance in the manufacturer datasheet. Decoupling capacitors should be placed directly at the appropriate supply pins, with careful attention to the exposed-pad connection for thermal performance. This product page combines the core device specifications, verified technical characteristics, application guidance, and replacement analysis. It also highlights the practical distinction between a genuine package-compatible substitution and a superficially similar PLL whose register map, RF limits, electrical ratings, or pin assignments may differ.
ADF4153YCPZ-RL - 4 GHz Fractional-N PLL | Analog Devices
The Analog Devices ADF4153YCPZ-RL is a fractional-N frequency synthesizer with RF bandwidth to 4 GHz, a 3.3 V power supply, programmable fractional modulus, and a separate charge-pump supply input in a 20-pin LFCSP package with exposed pad. The Y-version operating-temperature grade extends to +125°C, making the device suitable for industrial, instrumentation, communications, and automotive-adjacent RF signal-chain designs. A fractional-N frequency synthesizer belongs to the clock generation and timing hierarchy: it uses a phase-locked loop, or PLL, to multiply or divide a stable reference frequency and generate a programmable output. The ADF4153 supports fractional division, allowing frequency synthesis without an integer divider alone. This makes it useful for local oscillators in wireless transmitters and receivers, as well as test and measurement systems requiring fine frequency resolution. The ADF4153 architecture combines a low-noise digital phase-frequency detector, a precision charge pump, programmable fractional-N feedback circuitry, and a 4 GHz RF output stage. Its programmable fractional modulus supports flexible frequency planning. The separate VP input permits the charge-pump supply to be adjusted independently, which provides an additional tuning-voltage control option when supported by the surrounding circuit. The ADF4153YCPZ-RL is identified as a single fractional-N RF synthesizer with one PLL. Its 20-pin LFCSP exposed-pad construction supports compact layouts while providing a thermal path from the device to the PCB. The operating-temperature indication for the Y version reaches +125°C, although designers should confirm the complete electrical limits and automotive-grade requirements in the manufacturer datasheet before applying the part to a safety- or mission-critical application. Typical applications include wireless receiver and transmitter local oscillators, microwave downconverters, microwave upconverters, RF test equipment, instrumentation, and frequency-generating subsystems. The 4 GHz maximum RF frequency makes it appropriate for RF conversion stages operating below that limit. In these systems, the device can derive a coherent local-oscillator signal from a stable reference while allowing digital control of the output frequency. When implementing the device, follow the manufacturer reference-circuit and pin-description guidance for the LFCSP exposed pad. Decoupling should be placed directly at the relevant supply pins, the loop-filter components should follow the recommended calculation method, and the RF output network should be impedance matched for the target operating band. The exposed pad requires a properly designed ground-plane connection for electrical and thermal performance. This product record combines the official ADF4153 device information, exact MPN listing details, package characteristics, commercial sourcing data, and a practical comparison framework. It is designed to help engineers identify whether the ADF4153YCPZ-RL meets the required frequency, temperature, package, and sourcing constraints before beginning a PCB implementation.
ADF4153YCPZ-RL7 - 4GHz Fractional-N Synthesizer | Analog Devices
The Analog Devices ADF4153YCPZ-RL7 is a single-channel fractional-N frequency synthesizer with a maximum synthesizer frequency of 4 GHz, supplied in a 20-lead VFQFN package with an exposed pad. The device generates local-oscillator signals for the upconversion and downconversion sections of wireless receivers and transmitters. Its four principal functional blocks are a low-noise digital phase-frequency detector, a precision charge pump, a programmable reference divider, and a sigma-delta fractional interpolator that supports programmable fractional-N division. A fractional-N frequency synthesizer is a clock-generation and timing IC that locks a programmable output frequency to a stable reference. It belongs to the phase-locked-loop family, combining a phase-frequency detector, charge pump, feedback divider, loop filter, voltage-controlled oscillator, and programmable division circuitry. Fractional-N architecture permits frequency synthesis without requiring every integer-N ratio, making this device useful where wireless equipment needs a finely programmable local oscillator with compact implementation. The ADF4153 family is designed for RF signal-chain applications in which a received or transmitted signal must be translated to another frequency. Its 4 GHz maximum synthesizer frequency supports radio-frequency signal generation, while the single-channel architecture simplifies control for designs requiring one local-oscillator channel. The sigma-delta fractional interpolator and programmable reference divider provide the core functions needed for fractional frequency planning. The exact reference-divider range, phase-noise profile, lock-time limits, and channel-selection architecture should be confirmed in the manufacturer specifications before final RF performance is committed. The 20-VFQFN exposed-pad package supports compact surface-mount layouts, but thermal and RF layout requirements remain central to implementation. The exposed pad must be connected to the intended ground plane according to the package drawing, and the manufacturer pin and land-pattern instructions should govern pad dimensions and trace geometry. Because this is a fractional-N part, its reference input, feedback path, charge-pump network, and loop-filter implementation strongly influence spur performance and phase noise. Typical uses include wireless receiver and transmitter local oscillators, RF upconversion and downconversion chains, test and measurement equipment, instrumentation, and communication systems that require programmable frequency generation below 4 GHz. The device is also suited to designs where a reference clock and feedback divider establish the target synthesis frequency. System-level spur and phase-noise performance depends on the selected frequency ratio, reference quality, loop bandwidth, charge-pump settings, and printed-circuit-board implementation. For a new layout, follow the Analog Devices recommended decoupling and grounding scheme, preserve short return paths around the reference and feedback pins, and place loop-filter components close to the charge-pump and synthesizer interfaces. Avoid long exposed-pad vias that impair thermal performance. Before replacing another synthesizer, verify pin functions, supply requirements, reference-divider limits, register compatibility, and lock behavior rather than relying on package similarity alone. This page organizes the verified device identity, package, architecture, sourcing information, application context, and engineering checks into one compact reference. It also distinguishes true pin-compatible alternatives from superficially similar frequency synthesizers, helping designers assess whether a replacement can preserve the existing PCB, register sequence, and RF performance without hidden redesign work.