بەرهەمەکان (5,100+)

ADM489ABRMZ - 5V Full-Duplex RS-485 Transceiver | ADI
ADM489ABRMZ

ADM489ABRMZ - 5V Full-Duplex RS-485 Transceiver | ADI

Analog Devices ADM489ABRMZ is a 5 V, full-duplex differential line transceiver for balanced RS-422 and RS-485 communication, operating from a 4.5 V to 5.5 V supply at up to 250 kbps in a 10-pin MSOP package. It combines one differential line driver and one differential receiver in a low-power interface suitable for multipoint bus transmission lines. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and receives differential signals from the bus. The differential signaling method supports noise immunity and reliable communication over longer cable runs. Within the interface IC hierarchy, the ADM489ABRMZ is a physical-layer line transceiver designed for industrial data links, instrumentation, factory equipment, and embedded control networks. The principal operating characteristics are a 4.5 V to 5.5 V supply range, 250 kbps maximum signaling rate, full-duplex operation, and support for both EIA RS-422 and EIA RS-485. The device is described by Analog Devices as a low-power, slew-rate-limited transceiver. Slew-rate limitation reduces the high-frequency energy imposed on the bus, helping reduce electromagnetic interference and unwanted reflections on correctly terminated networks. The ADM489A family uses a mixed BiCMOS process that combines low-power CMOS circuitry with fast-switching bipolar technology. Its single driver and receiver arrangement provides separate transmit and receive paths, allowing simultaneous two-way communication. Because it is a full-duplex device, the associated bus implementation normally uses a dedicated differential pair for transmission and another pair for reception rather than sharing one half-duplex pair. Typical uses include industrial control links, remote sensor interfaces, building automation equipment, test and measurement systems, and factory automation networks. The 250 kbps rate is appropriate for moderate-speed control and monitoring traffic rather than high-speed Ethernet or other protocols requiring much greater bandwidth. Its 10-pin MSOP format supports compact, surface-mount PCB layouts. Designers should verify the supply rails, driver and receiver enable functions, bus topology, cable length, and termination requirements against the ADM489A datasheet. A 120-ohm termination resistor is commonly placed at each physical end of a correctly terminated RS-485 bus, while unused driver and receiver paths must be configured according to the device instructions. Decoupling and differential-routing practices are also important for reliable operation. This page combines the ADM489A product information with interface selection guidance, comparison parameters, and application-focused design notes. It is intended to help engineers determine whether the 5 V, 250 kbps, full-duplex MSOP transceiver fits a specific balanced communication link before beginning PCB implementation.

RFQ پەیوەندی
ADM489ABRZ - 250kbps Full-Duplex RS-485 IC | Analog Devices
ADM489ABRZ

ADM489ABRZ - 250kbps Full-Duplex RS-485 IC | Analog Devices

The Analog Devices ADM489ABRZ is a low-power differential line transceiver for balanced multipoint bus communication, supporting EIA RS-485 and RS-422 operation at 250 kbps. The device combines one differential driver and one differential receiver in a 14-lead SOIC package. Its full-duplex architecture supports simultaneous transmission and reception, making it suitable for industrial control networks, building automation, and instrumentation links. A differential line transceiver is an interface circuit that converts a single-ended logic signal into a balanced differential signal for reliable data transmission over long cables and noisy environments. The ADM489 family belongs to the RS-485 transceiver hierarchy, where the differential driver and receiver improve common-mode noise rejection compared with single-ended communication. Key electrical characteristics include operation from a 5 V supply, a maximum signaling rate of 250 kbps, and slew-rate-limited driver outputs that reduce harmonic distortion on the bus. The part supports both RS-485 and RS-422 balanced-data standards. Its 14-pin SOIC package is a widely used surface-mount footprint suitable for automated assembly and compact industrial controller designs. The full-duplex configuration keeps the transmit and receive paths active simultaneously, avoiding the shared-bus turn-around delay required by half-duplex transceivers. This makes the ADM489ABRZ appropriate when continuous monitoring is required during transmission, when a bus node must exchange data independently, or when a point-to-point link uses separate differential pairs for each direction. Typical applications include industrial RS-485 fieldbus links, factory-floor sensor and actuator networks, building HVAC controls, industrial gateways, test equipment, and remote I/O modules. The 250 kbps rate and 5 V operation align well with moderate-speed control and monitoring networks rather than high-bandwidth data protocols. When laying out a circuit, route the driver and receiver differential pairs as controlled-impedance traces and keep the bus-side connections short and symmetrical. Provide the interface's required bypass capacitance at the supply pins and connect unused inputs to defined logic levels rather than leaving them floating. Confirm termination, biasing, and grounding against the selected network topology. This page consolidates the family-level electrical positioning, package information, cross-reference candidates, and practical interface-layout guidance to support faster component selection and PCB planning.

RFQ پەیوەندی
ADM489AN - Low-Power RS-485/RS-422 Transceiver | Analog Devices
ADM489AN

ADM489AN - Low-Power RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices ADM489AN is a low-power differential line transceiver designed for RS-485 and RS-422 communication over multipoint bus transmission lines. The device combines one transmitter and one receiver in a 14-pin PDIP package and operates from a 4.5 V to 5.5 V supply. Its differential signaling supports balanced data transmission while slew-rate limiting helps control unwanted reflections and ringing on terminated communication buses. The ADM489AN is intended for industrial, instrumentation, communications, and embedded systems that require an EIA RS-485 or RS-422 interface. An RS-485/RS-422 transceiver is an interface integrated circuit that converts between single-ended logic signals and differential line signals. The differential receiver evaluates the voltage difference between the positive and negative bus conductors, improving noise immunity and allowing reliable data transmission over longer cable runs. In a multipoint network, multiple transceivers can share the same bus when the network is properly terminated and configured. The ADM489 family combines this physical-layer signaling function with low-power operation and slew-rate-controlled outputs. The verified product information identifies the ADM489 as a single RS-422/RS-485 transceiver with one driver and one receiver. Its 4.5 V to 5.5 V supply range is suitable for conventional 5 V digital systems, while the 14-pin PDIP package supports through-hole PCB assembly and prototype development. The product is suitable for industrial control equipment, data acquisition systems, instrument interfaces, building automation equipment, and other balanced communication links. The ADM489AN designation identifies the Analog Devices PDIP-14 version of the ADM489 family. The differential bus interface allows the transmitter and receiver to share the same physical cable pair. In a transmitting state, the driver produces a differential voltage across the bus. In a receiving state, the receiver converts that differential voltage into a logic-level output for the host controller or digital interface. This arrangement reduces sensitivity to common-mode voltage and electrical noise relative to single-ended signaling. Proper cable length, termination, grounding, and transceiver configuration remain important because the transceiver does not remove the need for correct network design. A typical RS-485 application connects the transceiver between a microcontroller or programmable logic controller and a field bus. The microcontroller drives the transmitter input and receives the receiver output, while the transceiver connects to the A and B differential conductors. An RS-422 point-to-point system can also use the same type of balanced interface. Because the ADM489AN operates from a 4.5 V to 5.5 V supply, the surrounding logic must use compatible voltage levels and provide suitable input and output interfacing. For PCB layouts using the PDIP-14 version, place decoupling capacitors close to the supply pins and route the differential bus with matched, symmetric geometry wherever practical. Keep the transceiver-side bus traces away from noisy switching nodes and high-current return paths. Termination should be placed at the physical ends of the bus rather than at every node. The receiver and driver enable functions should be controlled so that the bus is not driven in an unintended state during reset or power sequencing. This product page combines the verified Analog Devices product information, distributor package details, pricing availability, and cross-reference findings for the ADM489AN. It also highlights the practical RS-485/RS-422 design considerations that are not apparent from the part number alone: the 4.5 V to 5.5 V supply range, the 14-pin PDIP package, the single-driver/single-receiver architecture, and the requirement to validate each candidate replacement against the original datasheet before PCB substitution.

RFQ پەیوەندی
ADM489ANZ - 250kbps RS-485/RS-422 Transceiver | Analog Devices
ADM489ANZ

ADM489ANZ - 250kbps RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices ADM489ANZ is a full-duplex, low-power, slew-rate-limited differential line transceiver designed for EIA RS-485 and RS-422 communication networks. It provides one driver and one receiver, operates from a 4.5 V to 5.5 V supply, supports data rates up to 250 kbps, and is packaged in a 14-pin PDIP. The device also provides a ±10% supply variation tolerance for the ADM489ANZ grade. An RS-485 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over long, noisy, or multipoint wiring. An RS-422 transceiver serves a similar physical-layer role for balanced point-to-point links. The ADM489ANZ belongs to the transceiver, interface IC, and communications-semiconductor hierarchy, providing the physical layer between digital controllers and industrial cabling. Slew-rate limiting is a key feature of the ADM489ANZ. It reduces the rate at which driver edges transition, limiting high-frequency energy that can propagate through cables and disturb neighboring systems. This behavior makes the device suitable for industrial, instrumentation, building-control, and equipment networks where a moderate 250 kbps data rate is sufficient and controlled transitions improve interoperability. The ADM489ANZ operates from a single 4.5 V to 5.5 V supply, placing it in the 5 V interface-device class. Its one-driver, one-receiver organization supports full-duplex operation, while its differential driver and receiver interface is intended for balanced transmission lines. The operating temperature range extends from -40 °C to +85 °C, allowing use across industrial and commercial temperature conditions. Typical applications include industrial control networks, factory automation links, building automation equipment, instrumentation, and other balanced data buses. Because the interface is full duplex, transmit and receive paths can operate simultaneously. System designers must still observe the bus topology, termination, grounding, and enable-control requirements described in the manufacturer datasheet. For new layouts, place the transceiver close to the connector and route the balanced pair as a tightly coupled differential pair with a continuous ground reference. Appropriate termination and biasing depend on the cable length, topology, and network design. Check signal polarity and driver-enable timing before operation to prevent multiple transmitters from driving the bus simultaneously. This page combines the manufacturer electrical and ordering information with package details, interface-selection guidance, verified source links, and practical comparison criteria. It is intended to help engineers evaluate the ADM489ANZ for a new RS-485 or RS-422 design and to identify whether a candidate replacement truly preserves its package, pinout, operating range, and communications behavior.

RFQ پەیوەندی
ADM489AR - 250kbps Full-Duplex RS-485/422 | Analog Devices
ADM489AR

ADM489AR - 250kbps Full-Duplex RS-485/422 | Analog Devices

The Analog Devices ADM489AR is a low-power, full-duplex, slew-rate-limited differential line transceiver rated for 250 kbps data transmission and supplied in a 14-pin SOIC package. It supports the EIA RS-485 and RS-422 standards, operates from a single 5 V supply within a 4.5 V to 5.5 V range, and provides separate transmit and receive paths for full-duplex point-to-point links. Its 12 kΩ minimum input impedance and ±12 V bus common-mode range provide practical margin in industrial multipoint networks, while 2 kV EFT protection helps withstand electrically noisy environments. An RS-485 transceiver is a physical-layer interface IC that converts logic-level signals into balanced differential bus voltages and receives differential bus voltages back into CMOS-compatible logic. This device belongs to the interface-IC hierarchy, alongside RS-422 transceivers and other differential data-interface products, and sits between a digital controller and a wired communications bus. Full duplex allows the transmitter and receiver to operate simultaneously, which is useful when a node cannot wait for bus turnaround. Key features include a 250 kbps data rate, one driver and one receiver, 5 V single-supply operation, ±12 V common-mode handling, and controlled slew rate. The slew-rate limitation reduces high-frequency harmonics and reflected-signal problems by preventing excessively fast bus transitions. The 2 kV EFT protection rating is particularly relevant in industrial environments where cables may carry electrostatic-discharge transients. The ADM489AR integrates separate differential driver outputs and receiver inputs rather than using a single shared multipoint bus segment like a half-duplex transceiver. Its architecture therefore suits point-to-point full-duplex equipment, industrial controllers, and communications links where continuous send and receive capability is required. Exact pin identities, output-disable behavior, receiver enable logic, and detailed electrical limits should be confirmed against the manufacturer datasheet before layout or firmware release. Typical uses include industrial RS-485 links, RS-422 point-to-point interconnects, factory automation equipment, remote sensor interfaces, and embedded control systems. In a 5 V design, the transceiver can bridge a microcontroller UART and a balanced cable while maintaining compatibility with established differential-bus infrastructure. Compared with half-duplex RS-485 designs, the main system benefit is simultaneous transmission and reception without shared-driver contention. A key design consideration is that low data rate alone does not eliminate the need for correct bus termination, controlled impedance, common-mode grounding, and transient protection. The differential pair should be routed as a balanced pair, with connector and cable arrangements selected to minimize external noise pickup. Supply decoupling should be placed close to the device, and unused or disabled inputs must be handled according to the datasheet to avoid floating digital nodes. This product page consolidates verified manufacturer and distributor information, sourced pricing references, engineering application guidance, and honest replacement screening. It distinguishes confirmed facts from parameters that require the datasheet, helping engineers evaluate the ADM489AR for procurement and board-level design without treating merely similar RS-485 devices as verified drop-in replacements.

RFQ پەیوەندی
ADM489ARU - 250 kbps Full-Duplex RS-485 | Analog Devices
ADM489ARU

ADM489ARU - 250 kbps Full-Duplex RS-485 | Analog Devices

The Analog Devices ADM489ARU is a low-power, full-duplex differential line transceiver designed for RS-485 and RS-422 communications. It supports data rates up to 250 kbps, operates from a single +12 V supply, and provides a bus common-mode range of ±12 V. The device is packaged in a 16-pin TSSOP package. Its slew-rate-limited drivers reduce unwanted line transients, while the receiver provides a 12 kΩ input impedance and 2 kV EFT protection. A differential line transceiver is the physical-layer interface between digital logic and a balanced communication bus. The ADM489 belongs to the RS-485 and RS-422 transceiver hierarchy within interface ICs, combining a differential driver, differential receiver, and bus protection in one device. Balanced signaling improves noise immunity in industrial environments, while separate transmit and receive paths allow continuous full-duplex communication when the bus architecture supports independently routed pairs. The principal features include compliance with EIA RS-485 and RS-422 requirements, a maximum data rate of 250 kbps, and operation from a single +12 V supply. The ±12 V common-mode range supports systems where the bus voltage can move relative to the receiver reference. A 12 kΩ receiver input impedance reduces loading on terminated networks, and the 2 kV EFT rating improves robustness in electrically noisy industrial installations. The slew-rate-limited transmitter is particularly important in RS-485 networks because it reduces the amplitude and duration of edge-related transients on the cable. Unlike a high-speed edge-focused data interface, this controlled transition approach prioritizes dependable multipoint-bus operation over maximum data throughput. The ADM489 includes separate driver-enable and receiver-enable controls, allowing the host logic to manage bus direction and receive state. Typical applications include industrial process-control networks, factory automation equipment, building-control systems, instrumentation links, and other balanced serial buses operating at moderate speed. Full-duplex operation is particularly useful when transmit and receive pairs are routed independently. The part can also support point-to-point RS-422 links where both ends communicate simultaneously and the transmitter can be disabled when the bus is idle. Designers should use the manufacturer's pin-description and application guidance when assigning termination, biasing, and protection components. The bus requires correct differential routing, controlled impedance where applicable, and a termination strategy matched to the cable topology. Keep sensitive analog and digital grounds connected according to the recommended layout, and verify that system common-mode voltage remains within the ±12 V bus range. This product page combines manufacturer specifications, package information, interface-design guidance, application fit, and verified replacement references. It is intended to help engineers evaluate the ADM489ARU for low-power full-duplex RS-485 and RS-422 designs while distinguishing electrical equivalence from changes that affect assembly, qualification, or sourcing.

RFQ پەیوەندی
ADM489ARUZ - Full-Duplex RS-485/RS-422 | Analog Devices
ADM489ARUZ

ADM489ARUZ - Full-Duplex RS-485/RS-422 | Analog Devices

The Analog Devices ADM489ARUZ is a low-power, full-duplex differential line transceiver designed for balanced RS-485 and RS-422 data links, with one driver and one receiver housed in a 16-pin TSSOP package. It operates from a 4.5 V to 5.5 V supply, supports data rates up to 250 kbps, and uses slew-rate-limited signaling for reduced electromagnetic interference on multipoint bus networks. An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential voltages for reliable communication over cables and long interconnects. In the hierarchy of electronic components, it belongs to the interface IC family and the broader category of data transceivers. Balanced differential signaling helps reject common-mode noise, while the full-duplex architecture permits simultaneous transmitting and receiving through separate differential pairs. The ADM489 provides separate driver-disable and receiver-enable control functions, allowing the transmitter to be released during reception and supporting a multipoint bus configuration. Its low-power design is intended to reduce system consumption, while the slew-rate-limited driver helps limit high-frequency harmonics on the cable. The 16-pin TSSOP package offers a compact surface-mount footprint suitable for industrial control, instrumentation, and communications equipment. Because the ADM489 is a full-duplex device, each transceiver requires a dedicated differential driver connection and a separate differential receiver connection. The EIA RS-485 provisions cited by the Analog Devices datasheet include driver-disable capability, support for as many as 32 receivers on one line, and safety behavior during line contention. Only one driver should be active at a time, even though the device is electrically designed to withstand contention conditions. Typical uses include industrial RS-485 buses, remote sensor links, laboratory equipment, building controls, and embedded instrumentation. The 250 kbps maximum signaling rate is appropriate for moderate-speed control and monitoring networks rather than high-speed backplane or Ethernet applications. The 4.5 V to 5.5 V supply range also makes the device suitable for conventional 5 V industrial and embedded systems. PCB design should provide a continuous return path beneath the differential pair, minimize stubs from connectors and test points, and use controlled-impedance routing where cable transitions occur. Place the transceiver close to the connector, keep the RS-485 and RS-422 nets away from switching nodes, and follow the manufacturer’s grounding and termination guidance. Decoupling capacitors should be positioned close to the supply and ground pins. This page organizes the ADM489ARUZ interface, package, operating limits, application guidance, and selection considerations into an engineering-focused reference. It also identifies the verified drop-in alternatives that preserve the same TSSOP footprint and distinguishes true device replacements from unrelated RS-485 products with different transceiver architecture.

RFQ پەیوەندی
ADM489ARZ - 250 kbps Full-Duplex RS-485/RS-422 Transceiver | Analog Devices
ADM489ARZ

ADM489ARZ - 250 kbps Full-Duplex RS-485/RS-422 Transceiver | Analog Devices

The Analog Devices ADM489ARZ is a full-duplex, low-power differential line transceiver for balanced RS-485 and RS-422 data transmission, providing one differential driver and one differential receiver at up to 250 kbps in a 14-pin SOIC (0.154 in / 3.90 mm wide) package powered from a single 4.5 V to 5.5 V supply. An RS-485 transceiver is the physical-layer building block that converts a logic-level serial signal into a balanced differential signal for transmission over long, noisy cables, and converts the returning differential signal back into a logic-level output. The RS-485 standard defines a differential bus in which multiple receivers may listen to one driver pair, making it the most widely deployed industrial serial interface for factory automation, instrumentation, building controls, and networked sensors. The RS-422 companion standard adds point-to-point, full-duplex capability, which is exactly what the ADM489 implements with separate driver and receiver pin pairs. Key features of the ADM489ARZ include slew-rate limiting for reduced EMI and reflection, compliance with the EIA RS-485 and RS-422 standards, a 250 kbps data rate that comfortably covers legacy industrial protocols such as Modbus RTU at 19.2 kbps to 115.2 kbps, and tolerance of supply variation of plus or minus 10 percent around the nominal 5 V rail. Slew-rate-limited edges are the main reason the ADM489 is preferred over faster parts in noisy cabinet environments, since they suppress the ringing that causes false start bits and CRC errors. Architecturally the device combines a differential line driver, a differential receiver with fail-safe biasing, and separate active-high driver-enable and active-low receiver-enable inputs. That separation allows the two directions of the full-duplex link to be managed independently, so a system can hold its bus driver disabled in listen-only mode without tying up the receive path. The 14-pin SOIC footprint gives adequate lead spacing for hand assembly and automated pick-and-place while keeping the board area small. Typical deployments include industrial PLC and DCS remote I/O modules, RS-485 to RS-232 gateways, building HVAC controllers, utility and metering equipment, CNC machine tools, and long-cable sensor networks. The 250 kbps ceiling also suits legacy barcode scanners, weigh bridges, and access-control readers that use RS-485 or RS-422 over single runs of cable. A key design consideration is that the differential pair must be routed as a matched, tightly coupled pair over a continuous ground reference, with termination resistors of 100 ohm or 120 ohm fitted only at the two physical ends of the bus. Keep the transceiver close to the connector so that unbalanced stub lengths stay short, and decouple the 5 V supply locally with a 100 nF ceramic capacitor plus a bulk capacitor near the device. This page consolidates device specifications, drop-in pin-compatible alternatives, a parameter-by-parameter comparison table, and practical RS-485 layout and termination guidance that designers normally have to piece together from several separate documents.

RFQ پەیوەندی
ADM6996A2T1 - 10/100 Ethernet Switch Controller | Infineon
ADM6996A2T1

ADM6996A2T1 - 10/100 Ethernet Switch Controller | Infineon

The Infineon ADM6996A2T1 is a 10/100 Base-T/TX Ethernet switch controller with a parallel interface, packaged in a 128-BFQFP package. It integrates Ethernet switching and physical-layer interface functions for systems requiring 100 Mbps networking, providing a single-device solution for embedded Ethernet connections. An Ethernet switch controller is an interface IC that manages data traffic between a host processor and physical Ethernet ports. The ADM6996A2T1 belongs to the broader hierarchy of Ethernet controllers, network interface controllers, interface ICs, and semiconductors. Its parallel interface connects the switching functions to a digital host, while its 10/100 Base-T/TX capability supports Fast Ethernet equipment. The principal identified features are 10/100 Base-T/TX operation, a parallel processor interface, and a 128-BFQFP package. This combination is useful when a system needs an Ethernet interface close to the host logic without relying on an external plug-in module. The unified controller reduces the number of separate network-interface devices required in compact networking equipment. Technically, the part combines Ethernet switch control and physical-layer interface functionality in one integrated device. The parallel interface provides a direct digital connection to processors, FPGAs, or other embedded controllers, avoiding the serial interface commonly associated with network-on-chip solutions. Its 128-pin quad flat package provides the mixed-signal, power, ground, and digital I/O connections expected in a high-pin-count networking controller. Typical applications include industrial Ethernet equipment, embedded routers, network interface controllers, factory automation systems, and legacy Fast Ethernet infrastructure. The parallel interface may be especially useful in industrial designs where a processor or FPGA already handles packet processing and only requires a dedicated Ethernet front end. Designers should assign power, ground, analog Ethernet, clock, management, and parallel data signals according to the manufacturer pin-description table. Because the package exposes 128 connections, careful plane partitioning, solid grounding, and controlled routing around high-speed digital interfaces are essential. Confirm that host logic and the PCB land pattern match the exact ADM6996A2T1 configuration before layout release. This page organizes the known device identity, package information, sourcing guidance, same-package alternatives, and engineering-selection considerations. It also identifies where detailed electrical limits, clock requirements, register definitions, and absolute-maximum ratings must be confirmed in the manufacturer datasheet before a production design is approved.

RFQ پەیوەندی
ADN4624BCPZ - Quad 2.5Gbps LVDS Isolator | Analog Devices
ADN4624BCPZ

ADN4624BCPZ - Quad 2.5Gbps LVDS Isolator | Analog Devices

The ADN4624BCPZ is a quad-channel, signal-isolated, low-voltage differential signaling (LVDS) buffer from Analog Devices that operates at data rates up to 2.5 Gbps with very low jitter. It integrates Analog Devices' iCoupler technology, enhanced for high-speed operation, to provide drop-in galvanic isolation of LVDS signal chains. The device is available in a 32-lead WFQFN exposed pad package (LFCSP) and supports a wide supply range of 1.7 V to 1.9 V on both VDD1 and VDD2, with a typical supply of 1.8 V. It provides 5700 Vrms isolation voltage and a common-mode transient immunity (CMTI) of 40 kV/µs, making it suitable for industrial and medical applications where robust isolation is critical. A digital isolator is a device that transfers digital signals across an isolation barrier, typically using capacitive, inductive, or optical coupling, to protect sensitive circuitry from high voltages, ground loops, and noise. In the hierarchy of signal conditioning, a digital isolator sits between the digital signal source and the receiving logic, ensuring signal integrity and safety. The ADN4624BCPZ specifically isolates LVDS signals, which are differential, low-voltage, high-speed signals used in applications like data acquisition, industrial networking, and medical imaging. Key features of the ADN4624BCPZ include four isolated LVDS channels (4+0 configuration), a data rate of 2.5 Gbps per channel, and very low jitter, which is essential for high-speed serial links. The device also features a refresh mechanism that monitors input and output states to ensure they remain the same in the absence of data transitions, such as at power-on. The 1.8 V supplies for the LVDS and isolator circuits enable low power consumption while maintaining high-speed operation. Technically, the ADN4624BCPZ uses iCoupler technology, which employs chip-scale transformers to couple signals across the isolation barrier. This approach provides superior performance compared to optocouplers in terms of speed, power, and reliability. The device is designed to meet the stringent requirements of industrial automation, motor control, and medical equipment, where isolation and signal integrity are paramount. Typical applications include isolated LVDS interfaces in data acquisition systems, industrial fieldbus networks, and medical imaging equipment. The ADN4624BCPZ is also used in test and measurement instruments where high-speed data transfer with galvanic isolation is required. When designing with this device, ensure that the supply voltages are within the specified range and that proper decoupling capacitors are placed close to the VDD pins. The exposed pad should be soldered to the PCB ground plane for optimal thermal performance. Also, consider the CMTI rating when operating in environments with high voltage transients.

RFQ پەیوەندی
ADN4624BCPZ-RL7 - Quad LVDS Isolator 2.5Gbps | Analog Devices
ADN4624BCPZ-RL7

ADN4624BCPZ-RL7 - Quad LVDS Isolator 2.5Gbps | Analog Devices

The ADN4624BCPZ-RL7 is a quad-channel, signal-isolated, low-voltage differential signaling (LVDS) buffer from Analog Devices that operates at data rates up to 2.5 Gbps with very low jitter. It integrates Analog Devices' iCoupler technology, enhanced for high-speed operation to provide drop-in galvanic isolation of LVDS signal chains. The device is available in a 32-lead WFQFN exposed pad package (CSP) and provides 5.7 kV rms isolation voltage with a common-mode transient immunity (CMTI) of 40 kV/µs. A digital isolator is a component that provides galvanic isolation between two circuits while allowing digital signals to pass across the isolation barrier. In the hierarchy of isolation components, a digital isolator is a type of signal isolator, which falls under the broader category of isolation components used in power management and signal conditioning. The ADN4624 specifically isolates LVDS signals, which are differential, low-voltage, high-speed signals commonly used in high-speed data transmission. Key features include four isolated LVDS channels (4+0 configuration), support for 1.7 V to 1.9 V supply voltages on both sides (VDD1 and VDD2), and an operating temperature range of -40°C to +125°C. The device ensures very low jitter, making it suitable for high-speed serial links where signal integrity is critical. The 5.7 kV rms isolation rating provides robust protection against voltage transients and ground potential differences. Technically, the ADN4624 uses iCoupler technology, which employs chip-scale transformers to transmit data across the isolation barrier, offering advantages over optocouplers in terms of speed, power consumption, and reliability. The device supports AC coupling and/or level shifting to LVDS receivers and from LVDS drivers, simplifying interface design. The 32-lead WFQFN package with exposed pad aids in thermal management and is suitable for space-constrained applications. Typical applications include isolated high-speed data acquisition systems, industrial fieldbus interfaces, medical equipment requiring patient isolation, and communication backplanes. The device is ideal for systems where high-speed data must cross an isolation barrier without compromising signal integrity. When designing with the ADN4624, ensure proper PCB layout with adequate spacing for isolation, and place decoupling capacitors close to the VDD1 and VDD2 pins. The exposed pad should be connected to the appropriate ground plane for thermal performance.

RFQ پەیوەندی
ADP5585ACBZ-00-R7 - 10 I/O Keypad Controller | Analog Devices
ADP5585ACBZ-00-R7

ADP5585ACBZ-00-R7 - 10 I/O Keypad Controller | Analog Devices

The Analog Devices ADP5585ACBZ-00-R7 is a 10-I/O port expander with a built-in keypad matrix decoder, programmable logic, reset generator, and PWM generator, housed in a 16-WLCSP package measuring 1.59 mm by 1.59 mm. The device uses an I2C interface and is designed to increase the number of inputs and outputs available to a host processor or reduce host GPIO requirements in compact embedded systems. An I/O expander is an interface IC that adds configurable digital input and output pins to a processor through a serial bus. The ADP5585 extends this function with event-oriented keypad scanning, a 16-element FIFO for recording events, programmable logic, and PWM generation. Its 10 configurable I/Os can support keypad decoding and other peripheral functions in portable devices, remote controls, cameras, healthcare equipment, industrial instrumentation, and other compact control systems. The verified product data identifies the device as an 8-bit I/O expander with a 1 MHz I2C interface and an operating supply range from 1.65 V to 3.6 V. The 16-WLCSP package is intended for space-constrained PCB layouts, while the integrated keypad functionality helps designers reduce the number of discrete row and column connections required for matrix keypads. The device also provides reset-generation and programmable-logic functions that can simplify control-panel designs. The ADP5585 is especially useful when a system needs both general-purpose digital I/O and keypad event detection. Instead of assigning every keypad row and column directly to a microcontroller, the host processor can configure the ADP5585 through I2C and read keypad events from the device FIFO. This can reduce processor pin count and simplify firmware organization, although the exact implementation must follow the manufacturer's register and electrical guidance. ADP5585ACBZ-01-R7 and ADP5585ACPZ-01-R7 are mentioned in the manufacturer datasheet for configurations supporting a larger keypad matrix. The target ADP5585ACBZ-00-R7 should therefore be selected only after confirming the required matrix size, pinout, voltage range, and register behavior. The available verified data does not provide exact pricing, complete pin names, lifecycle status, or a complete pinout for this specific ordering code. This page combines the verified manufacturer and distributor information with application guidance, design cautions, and comparison placeholders where source data is unavailable. Review the manufacturer datasheet before finalizing PCB layout, firmware, voltage tolerances, or production sourcing.

RFQ پەیوەندی
ADP5585ACBZ-01-R7 - 10-I/O Keypad Port Expander | Analog Devices
ADP5585ACBZ-01-R7

ADP5585ACBZ-01-R7 - 10-I/O Keypad Port Expander | Analog Devices

Analog Devices ADP5585ACBZ-01-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and PWM generator. The device supports keypad matrices up to 6 × 5 and provides a 16-element FIFO for event recording. It is packaged in a 16-WLCSP measuring 1.59 mm × 1.59 mm. An I/O expander is an interface IC that increases the number of digital input and output pins available to a host processor. A typical I2C or SPI expander connects through a serial bus, allowing a microcontroller to monitor switches, read a keypad matrix, drive indicators, or control auxiliary signals without dedicating one host pin to every function. The ADP5585 combines this general-purpose expansion role with dedicated keypad-scanning and programmable-logic functions. The ADP5585 provides 10 configurable I/Os and a 16-event FIFO. Its keypad capability can decode a matrix as large as 6 × 5, reducing the number of host pins and GPIO connections needed for human-interface controls. Programmable logic adds local digital behavior, while the reset generator and PWM generator broaden the device beyond simple level translation or GPIO expansion. The ADP5585ACBZ-01-R7 option is identified in the Analog Devices datasheet as a configuration intended for a larger 6 × 5 keypad matrix. The integrated FIFO retains event identifiers so software can retrieve recorded keypad events sequentially. This is particularly useful when the host processor must perform other processing between scans or when debounce and event handling need centralized firmware control. Typical uses include portable-device keypads, camera controls, remote-control panels, healthcare interfaces, and industrial instrumentation. The same device can support general digital I/O expansion when a keypad matrix is not required. Its small 1.59 mm × 1.59 mm 16-WLCSP package is suited to space-constrained systems, although careful PCB layout and assembly planning are necessary because of the fine package geometry. Designers should confirm the exact pin assignments, electrical limits, serial-interface settings, and supported keypad configuration against the manufacturer datasheet before layout release. Because the verified source data does not expose a public pin table or complete electrical limits in the supplied excerpts, unavailable values should be confirmed from the official ADP5585 datasheet rather than inferred from the orderable MPN.

RFQ پەیوەندی
ADP5585ACBZ-02-R7 10-I/O Keypad Controller | Analog Devices
ADP5585ACBZ-02-R7

ADP5585ACBZ-02-R7 10-I/O Keypad Controller | Analog Devices

Analog Devices ADP5585ACBZ-02-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, PWM generator, and a 16-event FIFO, housed in a 16-ball WLCSP package measuring 1.59 mm by 1.59 mm. The device communicates with a host processor through an I2C-compatible interface and includes ten configurable I/O resources that can support keypad scanning and general digital input/output expansion. The -02 configuration is identified by the verified distributor listing as the no-pullup option. An I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a microcontroller or embedded processor. The ADP5585 belongs to the broader hierarchy of I/O expander, interface IC, and semiconductor. In addition to conventional digital I/O expansion, this device incorporates dedicated keypad-scanning, programmable logic, reset, PWM, and event-recording functions, allowing a host to offload repetitive peripheral monitoring and conserve processor bandwidth. The principal verified features include 10 configurable I/Os and a 16-element event FIFO for recording keypad events. The FIFO allows the processor to read recorded events through the I2C-compatible interface instead of continuously polling every matrix input. Programmable logic and a PWM generator provide additional peripheral functions without requiring separate devices, while the reset generator supports system control functions. The -02 ordering option is specifically listed as a no-pullup keypad controller configuration. Internally, the ADP5585 combines programmable digital I/O resources with a keypad matrix decoder and event-recording architecture. A larger matrix can be configured with related -01 ordering options, but the exact supported matrix arrangement and event identifiers depend on the selected pins and configuration. Because the target -02 option omits pullups, external input conditioning or pullup resistors may be required wherever the scanned keypad or digital input interface does not otherwise establish the required high state. The host should configure the device through its register interface before relying on advanced functions. Typical uses include compact keypad interfaces in remote controls, medical and industrial instrumentation, consumer appliances, and portable equipment. Its small 1.59 mm by 1.59 mm WLCSP footprint is particularly useful when board area is constrained. The device can also reduce host pin count by combining keypad scanning, discrete digital I/O, programmable logic, reset generation, and PWM generation in one package. Suitable companion components include host microcontrollers, I2C bus devices, keypad matrices, and analog or mixed-signal front ends. Designers should account for the no-pullup configuration of the -02 option and confirm the external resistors required by the selected keypad topology. I2C pullups and all supporting pullup networks should be calculated for the actual bus voltage, speed, capacitance, and number of connected devices. Layout must preserve short, clean I2C routing and adequate ground return paths in the compact WLCSP footprint. Software should use the FIFO and interrupt mechanism to avoid unnecessary polling and should test event behavior across the configured matrix. This page combines verified manufacturer and distributor information with a practical feature analysis, same-brand drop-in assessment, pinout limitation, application guidance, and design notes. It distinguishes confirmed capabilities from electrical parameters that require the full manufacturer datasheet, helping engineers make a defensible sourcing and design decision.

RFQ پەیوەندی
ADP5585ACBZ-04-R7 - 10-I/O Key Controller | Analog Devices
ADP5585ACBZ-04-R7

ADP5585ACBZ-04-R7 - 10-I/O Key Controller | Analog Devices

The Analog Devices ADP5585ACBZ-04-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and PWM generator, supplied in a 16-WLCSP package measuring 1.59 mm by 1.59 mm. It is designed to add configurable input/output and keypad-scanning functions to compact embedded systems while limiting external controller pin count. An I/O expander is an interface IC that extends the number of digital inputs and outputs available to a host microcontroller through a serial interface. In the broader device hierarchy, the ADP5585 belongs to the I/O expander class of interface ICs and combines general-purpose GPIO expansion with dedicated keypad decoding, programmable logic, reset, and PWM functions. This integration is particularly useful in portable devices, remote controls, cameras, healthcare equipment, and industrial instrumentation. The verified product information identifies 10 configurable I/O ports, a built-in keypad matrix decoder, programmable logic, a reset generator, and a PWM generator. The -04 configuration is presented by DigiKey as keypad and I/O-expansion functionality, while Mouser identifies it as a 10-GPIO/key-controller device without pull-up resistors. These integrated functions can reduce the number of discrete logic, keypad-scanning, and reset components required in a compact design. The ADP5585 architecture separates several system-control tasks into one interface device. Programmable logic can implement local input relationships, the keypad decoder can organize matrix-scanned events, the reset generator can support controlled peripheral initialization, and the PWM generator can provide a configurable modulation output. Exact operating voltage, current consumption, serial-interface timing, programmable-logic limits, and electrical timing values are not included in the supplied verified excerpts and must be confirmed in the manufacturer datasheet before design release. Typical applications include handheld keypads, camera controls, remote-control interfaces, portable medical-device panels, and compact industrial instruments. The 16-WLCSP package is appropriate when board area is constrained, although its fine pitch requires careful PCB layout, inspection, and assembly-process control. The lack of integrated pull-ups must also be considered when the external bus or keypad arrangement requires them. Designers should verify the exact -04 keypad configuration, required external pull-ups, exposed-pad connection, and recommended decoupling directly from the Analog Devices datasheet. Because this WLCSP package has no matching entry in the available package-diagram library, the product page uses the default package illustration rather than claiming a verified 16-ball pin map. This page consolidates verified manufacturer and distributor information, pricing evidence, same-family configuration choices, and practical integration considerations. It also distinguishes confirmed functions from parameters that require engineering review, providing a more useful sourcing and design starting point than distributor listings alone.

RFQ پەیوەندی
ADP5585ACPZ-00-R7 - 10-I/O Keypad Controller | Analog Devices
ADP5585ACPZ-00-R7

ADP5585ACPZ-00-R7 - 10-I/O Keypad Controller | Analog Devices

The Analog Devices ADP5585ACPZ-00-R7 is a 10-I/O port expander with built-in keypad matrix decoder, programmable logic, reset generator, and PWM generator, supplied in a 16-LFCSP 3x3 mm package. The device is designed for portable and embedded systems that need additional input/output pins, key-event handling, or auxiliary control functions without increasing the host processor pin count. An I/O expander is an interface IC that increases the number of general-purpose inputs and outputs available to a host processor. The ADP5585 family combines this port-expansion function with a keypad matrix decoder and programmable logic, allowing a processor to scan keypad inputs and receive buffered events while using fewer host pins. This makes the device suitable for product interfaces, handheld equipment, industrial instrumentation, and other control systems with compact human-machine interfaces. The verified product information identifies 10 configurable I/Os, a 16-element FIFO for event recording, a built-in keypad decoder, programmable logic, a reset generator, and a PWM generator. The ADP5585ACPZ-00-R7 is specifically identified as the standard address configuration. The manufacturer datasheet also states that the 7-bit device address is 0x34 for all models except ADP5585ACPZ-03-R7, which uses 0x30. The 16-LFCSP 3x3 mm package supports compact PCB layouts in space-constrained portable products and instrument panels. Because the supplied web results do not publish the complete pin names or detailed electrical limits in machine-readable form, the package pinout and several electrical parameters are marked as requiring verification from the manufacturer datasheet before schematic capture or layout release. Typical applications include keypad entry, camera controls, remote controls, portable devices, healthcare equipment, industrial instrumentation, and other embedded human-interface systems. The internal FIFO can record input events while the host processes other tasks, while programmable logic can provide local decision-making or control behavior. The PWM generator is useful for LED indicators, simple dimming, or other low-frequency auxiliary functions when its electrical limits are appropriate for the load. Designers should confirm the I/O voltage, absolute maximum ratings, address configuration, capacitor requirements, and exposed-pad connection directly from the manufacturer datasheet. The I/O pins should also be checked for pull-up, pull-down, keypad, logic-level, or push-pull requirements before they are assigned to a board layout. This page combines verified manufacturer and distributor information with practical application guidance and explicitly identifies values that require datasheet confirmation.

RFQ پەیوەندی
ADP5585ACPZ-01-R7 - 10-I/O Keypad Controller | Analog Devices
ADP5585ACPZ-01-R7

ADP5585ACPZ-01-R7 - 10-I/O Keypad Controller | Analog Devices

Analog Devices ADP5585ACPZ-01-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and PWM generator in a 16-LFCSP (3 x 3 mm) package. The device provides an I2C address of 0x34, 10 configurable I/Os, and event-recording capability through a 16-element FIFO. It is designed to increase the I/O capacity of a host processor while reducing the number of GPIO pins required for keypad scanning and auxiliary control functions. An I/O expander is an interface IC that extends the number of digital input and output lines available to a processor through a serial bus. In the product hierarchy, the ADP5585 is an I/O expander, an interface IC, and a power-management-adjacent system-support semiconductor. Its integration of keypad scanning, programmable logic, reset generation, and PWM generation can replace several discrete peripheral functions while conserving host-controller pins. The principal features include 10 configurable I/Os, a keypad matrix decoder supporting programmable scan operations, a 16-element FIFO for event recording, programmable logic, and a dedicated PWM generator. These functions are useful in handheld products, remote controls, cameras, healthcare equipment, industrial instrumentation, and human-interface panels. The integrated architecture reduces component count and can simplify firmware by moving repetitive scanning and event handling into dedicated hardware. Communication occurs through I2C-compatible serial transactions. According to the manufacturer datasheet, a transaction begins with a start condition, followed by the 7-bit device address and read/write bit. For ADP5585ACPZ-01-R7, the device address is 0x34, distinguishing it from the ADP5585ACPZ-03-R7 version, which uses 0x30. The part acknowledges the address byte by pulling the data line low, allowing the host to confirm that the target device is present and responding. Typical uses include portable-device keypads, camera control interfaces, remote-control panels, medical monitoring equipment, and industrial instrumentation. In each case, the device can manage multiple digital lines and matrix-scanning tasks while the main processor handles higher-level application logic. In designs requiring multiple PWM outputs, the internal generator reduces the need for external PWM circuitry, although exact timing, current, and configuration limits must be taken from the manufacturer datasheet. The principal design consideration is firmware and bus planning. Because the -01 and -03 order codes use different 7-bit I2C addresses, multiple identical devices can coexist on one bus if address selection and pull-up requirements are managed correctly. Firmware should also account for FIFO overflow conditions, event ordering, and the difference between input, output, and keypad-scanner configurations. The 3 x 3 mm LFCSP package requires a qualified land pattern and careful inspection because its small dimensions make solder bridging and assembly defects a concern. This product page consolidates verified manufacturer descriptions, distributor availability, family-level alternatives, interface details, and practical design guidance. It distinguishes confirmed ADP5585 features from parameters that still require verification in the manufacturer datasheet, helping engineers assess fit before beginning a PCB layout or firmware implementation.

RFQ پەیوەندی
ADP5585ACPZ-03-R7 - 10-I/O Keypad Controller | Analog Devices
ADP5585ACPZ-03-R7

ADP5585ACPZ-03-R7 - 10-I/O Keypad Controller | Analog Devices

Analog Devices ADP5585ACPZ-03-R7 is a 10-I/O port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and PWM generator, supplied in a 16-LFCSP package. The device operates from a 3.6 V supply according to distributor data and communicates with a host processor through an I2C interface. Its ten configurable I/Os allow digital input, digital output, keypad scanning, or mixed functions to be assigned through registers. The ACPZ-03-R7 option uses the I2C device address 0x30, while other ADP5585 models use 0x34. An I/O expander is an interface IC that increases the number of general-purpose input/output pins available to a microcontroller or system processor. It sits between the host and external controls, allowing a device with limited pin count to operate keypads, indicators, interlocks, and other digital peripherals. The ADP5585 expands this role by including a keypad matrix decoder and programmable logic, reducing the host burden associated with scanning switch matrices and recording button events. Key verified features include 10 configurable I/Os, a built-in keypad matrix decoder, programmable logic, a reset generator, and a PWM generator. A 16-element FIFO supports event recording, allowing qualifying input events to be retained and transferred over the serial interface. The device is intended for portable equipment such as phones, remote controls, and cameras, as well as non-portable healthcare, industrial, and instrumentation systems. The ADP5585 combines GPIO expansion with peripheral functions in one small package. Its I2C control path provides a practical way to add external interfaces without assigning a dedicated host GPIO to every keypad line or status indicator. Register-programmable behavior allows the same device family to support different board layouts, while the reset and PWM blocks reduce the need for separate discrete functions in compact control systems. The target suffix identifies the 16-LFCSP, 3 x 3 mm, tape-and-reel configuration. The ACPZ-03-R7 version is distinguished from other ADP5585 variants primarily by its device address and detailed configuration options. Because the I2C address differs from 0x34, firmware and bus planning should specifically account for the 0x30 address of this ordering code rather than assuming the address used by every other device in the family. Designers should confirm pin functions, exposed-pad requirements, address selection, and electrical limits directly against the manufacturer datasheet before layout release. I2C pull-up placement, bus capacitance, level compatibility, and the exposed thermal and electrical pad connection must be evaluated on the complete board rather than in isolation. This page consolidates the verified manufacturer function description, distributor ordering data, package information, I2C-address distinction, and family cross-references into one engineering-focused record. It also identifies which replacement details remain unverified, helping engineers distinguish confirmed pin-compatible family references from assumptions that would require schematic, firmware, and datasheet review.

RFQ پەیوەندی
ADP5586ACBZ-00-R7 - 10-I/O Keypad Decoder | Analog Devices
ADP5586ACBZ-00-R7

ADP5586ACBZ-00-R7 - 10-I/O Keypad Decoder | Analog Devices

The Analog Devices ADP5586ACBZ-00-R7 is a 10-input/output port expander with a built-in keypad matrix decoder, programmable logic, reset generator, and pulse generators in a 16-WLCSP package measuring 1.59 mm by 1.59 mm. The device supports I2C communication up to 1000 kHz and operates from a supply rated up to 3.6 V. Its default configuration supports keypad-entry and general-purpose I/O expansion without requiring a dedicated host GPIO pin for every external signal. An I/O expander is an interface IC that increases the number of inputs and outputs available to a microprocessor or microcontroller. The ADP5586 belongs to the interface IC hierarchy and combines an I2C-controlled GPIO expansion function with keypad scanning, event processing, and dedicated timing logic. This combination can reduce host pin count while supporting matrix keypads, discrete controls, indicators, and other low-speed peripheral signals. Key features include 10 configurable I/O resources, an integrated keypad matrix decoder, programmable logic, a reset generator, and pulse generators. The I2C interface operates up to 1000 kHz, making the device suitable for systems that need compact peripheral expansion and organized keypad event handling. The -00 configuration is identified as the default-config variant, while the separate -01 product model changes how the RST pin is used. Technically, the device separates host interface traffic from keypad-scanning and programmable I/O functions. Its reset behavior provides controlled initialization, while pulse-generation and programmable-logic functions can reduce repetitive host firmware. According to the manufacturer datasheet, the RST pin includes a debounce filter. The -01 model uses that pin as an additional R5 keypad row, whereas the selected -00 model retains the documented reset-related behavior. Typical applications include portable-device keypads, remote controls, camera controls, healthcare panels, industrial instrumentation, and compact human-interface systems. It is most useful when a design needs several discrete inputs plus a matrix keypad but has limited host-controller GPIO pins. Because the device targets compact, mixed-signal control panels rather than high-speed peripheral buses, board-level I2C routing and exposed-pad assembly are important practical considerations. Designers should review the WLCSP land pattern, exposed-pad requirements, I2C pull-up placement, and the difference between the -00 and -01 RST configurations before release. A clean bypass-capacitor layout and short I2C traces help preserve signal integrity in dense portable or industrial equipment. This page combines verified manufacturer and distributor information with application guidance, selection criteria, and explicit uncertainty notes where detailed operating values or drop-in replacements were not provided.

RFQ پەیوەندی
ADP5586ACBZ-01-R7 - 10-I/O Keypad Decoder | Analog Devices
ADP5586ACBZ-01-R7

ADP5586ACBZ-01-R7 - 10-I/O Keypad Decoder | Analog Devices

The Analog Devices ADP5586ACBZ-01-R7 is a 10-input/output port expander with an integrated keypad matrix decoder, programmable logic, reset generator, and pulse generators, packaged in a 16-WLCSP measuring 1.59 mm × 1.59 mm. It supports I2C communication up to 1000 kHz and is identified as a 3.6 V device. An I/O expander is a specialized interface IC that increases the number of inputs and outputs available to a host processor. It belongs to the hierarchy of interface IC, peripheral interface controller, and system semiconductor. The ADP5586 combines general-purpose port expansion with a dedicated keypad matrix decoder, making it useful where a system needs both configurable digital lines and matrix keypad scanning without allocating many host GPIO pins. The device provides 10 configurable I/O resources and supports a 6-row by 5-column keypad matrix. Additional onboard functions include programmable logic, reset generation, and pulse generation. The ADP5586ACBZ-01-R7-specific configuration assigns the active-low RST pin as an additional keypad row, R5, while the SW_RESET register bit or an undervoltage condition provides another reset path. The I2C interface operates at up to 1000 kHz, allowing efficient host communication for register configuration and real-time input monitoring. Its compact 16-WLCSP format reduces PCB area compared with a larger discrete keypad-scanning implementation, but its fine pitch requires careful PCB layout, inspection, and assembly planning. Analog Devices identifies the ADP5586 family as production product. Typical uses include portable-device keypads, remote controls, cameras, healthcare equipment, industrial control panels, and instrumentation. In each case, the device can scan a matrix keypad while exposing additional programmable lines for LEDs, control inputs, or other digital functions. Integrating these tasks in one package can reduce host GPIO usage and simplify the system interconnect. Designers should verify the exact pin functions, voltage limits, logic thresholds, and configuration registers against the manufacturer datasheet before layout. A low-noise supply and appropriately placed decoupling capacitors remain important because the device combines digital I/O, keypad scanning, and host-interface functions in one compact package. This product synthesis consolidates verified manufacturer and distributor information, a 16-WLCSP package description, current pricing references, pin-specific reset behavior, and application guidance. It also clearly distinguishes the target ordering code from broader ADP5586 family information and identifies where additional engineering verification is still required.

RFQ پەیوەندی
ADP5586ACBZ-03-R7 - 10-I/O Keypad Decoder | Analog Devices
ADP5586ACBZ-03-R7

ADP5586ACBZ-03-R7 - 10-I/O Keypad Decoder | Analog Devices

Analog Devices ADP5586ACBZ-03-R7 is a 10-input/output port expander with a built-in keypad matrix decoder, programmable logic, reset generator, pulse generators, and a 16-event FIFO in a 16-WLCSP package measuring 1.59 mm by 1.59 mm. The device communicates with a host processor through an I2C-compatible interface, allowing keypad and general-purpose I/O functions to be added without using a dedicated host I/O pin for every connection. An I/O expander is an interface IC that increases the number of digital input and output pins available to a microprocessor or microcontroller. Its place in the hierarchy is interface controller → I/O expander → keypad decoder → integrated circuit. By combining general-purpose I/O with automatic keypad scanning and event buffering, the ADP5586 reduces the polling burden on the host processor and can lower processor activity during keypad use. The verified product information identifies 10 configurable I/O resources, programmable logic, pulse-generation functions, an integrated reset generator, and a FIFO capable of storing up to 16 events. The -03 configuration uses the I2C-compatible interface and provides a default configuration identified by distributor listings. This combination makes the device useful where a compact keypad, discrete controls, or mixed digital I/O must be connected through a small number of serial interface pins. The ADP5586 architecture separates keypad decoding from the host processor. Keypad events can be captured in the 16-event FIFO and read over the serial interface, rather than requiring the processor to identify every press continuously. The programmable logic and pulse generators can support additional control functions, although individual timing limits, logic configurations, and I/O electrical characteristics must be confirmed in the manufacturer datasheet before final design release. Typical uses include portable-device keypads, camera controls, remote-control panels, healthcare user interfaces, industrial instrumentation, and compact control modules. In each case, the 16-WLCSP footprint conserves board area, while the integrated keypad decoder can reduce firmware complexity. Systems requiring more general-purpose I/O than the ADP5586 provides can use a dedicated I/O expander such as PCA9536DR alongside the keypad function. Designers should verify I2C address configuration, pull-up requirements, supported input and output drive levels, and the behavior of the RST and configuration pins in the Analog Devices ADP5586 Data Sheet (Rev. 0). Because the package is only 1.59 mm by 1.59 mm, PCB assembly should use suitable fine-pitch assembly capability, controlled solder-paste deposition, and inspection appropriate for the exposed land pattern. This product page combines verified manufacturer and distributor information, a 16-event FIFO feature, package details, purchasing data, and engineering-oriented usage guidance. It also identifies the important limitation that the verified cross-reference results do not establish five distinct pin-compatible replacements for the -03 configuration, avoiding unsupported drop-in claims.

RFQ پەیوەندی
ADP5587ACBZ-R7 - 18-GPIO I/O Expander | Analog Devices
ADP5587ACBZ-R7

ADP5587ACBZ-R7 - 18-GPIO I/O Expander | Analog Devices

The Analog Devices ADP5587ACBZ-R7 is a production mobile I/O expander and QWERTY keypad controller with 18 GPIO resources, a 400 kHz I2C interface, and 1.65 V to 3.6 V operation in a 25-WLCSP package measuring approximately 1.97 mm by 1.97 mm. It consolidates keypad scanning and additional digital I/O where a host processor has limited direct GPIO capacity. An I/O expander is an interface IC that extends a processor's input/output capacity over a serial bus. In the product hierarchy, the ADP5587 is an I/O expander, then a serial interface device and an integrated circuit. The ADP5587 adds value beyond ordinary GPIO expansion because its eight configurable GPIOs can operate as keypad rows or columns, while the remaining lines support general-purpose inputs, outputs, and interrupt signaling. Key features include support for an 18-GPIO configuration or a 10-by-8 keypad matrix, I2C auto-increment, an open-drain interrupt output, programmable pull-ups, key-press and key-release interrupts, a key-event counter with overflow indication, keypad locking, and a 275 microsecond debounce interval. These functions reduce host-side scanning logic while preserving event-driven communication with the processor. The device is designed around low-voltage mobile systems. Its I2C host interface runs at 400 kHz, and its 1.65 V to 3.6 V operating range suits compatible mobile and embedded rails. The compact WLCSP construction supports space-constrained handheld layouts, although its fine-pitch footprint demands careful PCB assembly, clean supply bypassing, and pin-accurate layout according to the Analog Devices package drawing. Typical uses include QWERTY keypad controllers, mobile handsets, portable navigation equipment, compact industrial user-interface panels, and other embedded products that need a dense matrix of switch inputs or additional GPIO lines. The host processor reads key events and configuration registers through I2C, while the interrupt line provides an event-driven indication of relevant key activity. For layout, keep I2C routing short, provide the required decoupling close to the supply pins, and verify the exposed-pad connection and assembly requirements in the manufacturer datasheet. Pull-ups must match the host voltage, bus capacitance, and timing budget. Software should also account for debounce, interrupt level programming, and event-counter overflow behavior. This page consolidates verified manufacturer and distributor facts, strict package constraints, application guidance, and clearly flagged data gaps. It distinguishes documented drop-in candidates from broader functional equivalents so engineers do not mistake a different footprint or feature set for a true PCB-level replacement.

RFQ پەیوەندی
ADP5587ACPZ-1-R7 - 18-GPIO I/O Expander | Analog Devices
ADP5587ACPZ-1-R7

ADP5587ACPZ-1-R7 - 18-GPIO I/O Expander | Analog Devices

The Analog Devices ADP5587ACPZ-1-R7 is an 18-GPIO I/O expander and QWERTY keypad controller with an I2C interface operating up to 400 kHz, packaged in a 24-LFCSP-WQ 4 mm × 4 mm package. It is designed for mobile platforms where the main processor has limited GPIO capacity and needs additional inputs, outputs, and keypad scanning functions. The verified distributor listing identifies the device as an 18-I/O expander with keypad-scanner functionality and a 400 kHz I2C interface. An I/O expander is an interface IC that increases the number of general-purpose input/output lines available to a host processor. The ADP5587 supports mobile keypad architectures by combining configurable GPIOs with keypad row and column functions, reducing the number of host pins required for physical key matrices. Its position in the hierarchy is GPIO expander → keypad controller → interface IC → semiconductor. The ADP5587 family is intended for QWERTY-type phone designs and similar human-interface systems. Its GPIO expansion capability allows the host to scan controls, read switch states, drive indicator or control lines, and manage keypad rows and columns through the serial interface. The I2C interface with auto-increment supports efficient register access, while the compact 24-LFCSP-WQ package supports space-constrained mobile equipment. The verified data does not provide complete electrical limits, pin-level functions, or timing values, so those parameters remain marked for data completion rather than inferred. Typical applications include mobile phone keypads, portable navigation devices, handheld terminals, compact consumer equipment, and other products that need more host-controlled I/O than the processor exposes directly. The ADP5587 is particularly useful when a design needs both general-purpose digital lines and keypad scanning in one device. Compared with a pure GPIO expander, it adds keypad-oriented functions; compared with a larger host MCU, it can reduce processor pin count and centralize human-interface I/O. Designers should verify the package-specific pinout, I2C address configuration, voltage limits, and electrical timing against the manufacturer datasheet before layout. The compact WQ package also requires careful PCB escape routing and thermal assessment according to the manufacturer’s recommended land pattern. This page combines verified distributor availability and product descriptions with structured application guidance and clearly identifies parameters that require datasheet confirmation.

RFQ پەیوەندی
ADP5587ACPZ-R7 - 18-GPIO Mobile I/O Expander | Analog Devices
ADP5587ACPZ-R7

ADP5587ACPZ-R7 - 18-GPIO Mobile I/O Expander | Analog Devices

The Analog Devices ADP5587ACPZ-R7 is a mobile I/O expander and QWERTY keypad controller with 18 GPIOs, an 8×8 keypad matrix, and a 400 kHz I2C interface. It operates from 1.65 V to 3.6 V and is housed in a 24-lead LFCSP-WQ package measuring 4 mm × 4 mm. The device is designed to add key-scanning and general-purpose I/O capacity when a mobile processor has limited GPIO resources. An I/O expander is an interface IC that extends a host processor through a serial bus. The ADP5587 supports eight independently configurable general-purpose inputs and outputs plus keypad matrix functions, placing key scanning and decoding in a compact peripheral. In the system hierarchy, it is an I/O expander, interface IC, and mobile system peripheral. Its 400 kHz I2C rate allows the host to update I/O state while the integrated keypad logic handles scanning. The supplied manufacturer information identifies an 18-GPIO port expander, configurable GPIOs, and an 8-keypad-matrix implementation. It also provides keypad-lock functionality and operation to 3.6 V. These features make the device relevant to QWERTY phones and other compact portable systems where board area and host-pin count are constrained. The part uses an I2C interface with auto-increment, reducing host-side register-access overhead for sequential register updates. Its 2 mm × 2 mm core package description in the manufacturer snippet corresponds to the compact class of device intended for mobile designs, while distributor records identify the ordering code as a 24-LFCSP-WQ, 4 mm × 4 mm package. Exact pin names, electrical limits, and register details require the official datasheet rather than distributor summaries. Typical uses include QWERTY keypad scanning, mobile navigation controls, compact wearable interfaces, portable measurement controls, and industrial panels requiring additional GPIO. The device can reduce direct processor connections, although the I2C bus and interrupt behavior must be checked against the host system requirements. When designing around the ADP5587, first verify the exact ACPZ pinout, exposed-pad connection, voltage limits, and decoupling requirements in the Analog Devices datasheet. Confirm that the host I2C voltage, address configuration, and keypad matrix geometry match the intended board. This page combines verified manufacturer and distributor information, lifecycle context, package details, commercial questions, and engineering-oriented design guidance. It also distinguishes confirmed drop-in alternatives from functional equivalents that may require different packages or pin assignments.

RFQ پەیوەندی