بەرهەمەکان (5,100+)

PCA9555BSHP - 16-Bit I2C I/O Expander | NXP | HVQFN-24
PCA9555BSHP

PCA9555BSHP - 16-Bit I2C I/O Expander | NXP | HVQFN-24

The NXP Semiconductors PCA9555BSHP is a 16-bit I2C-bus and SMBus I/O expander with an interrupt output, operating at bus speeds up to 400 kHz and supporting a maximum supply voltage of 5.5 V. The device is offered in a 24-HVQFN package measuring 4 x 4 mm and is supplied in tape-and-reel packaging. Its 16 port pins can be configured individually as inputs or outputs, allowing a host microcontroller to monitor external signals and control LEDs, relays, or other digital loads through one serial interface. An I/O expander is an interface IC that increases the number of general-purpose digital input and output pins available to a host processor. The PCA9555BSHP occupies the level between a microcontroller and the discrete GPIO circuitry connected to it: the controller communicates over I2C or SMBus, while the expander converts eight register bits into eight outputs or reads back eight inputs. The integrated interrupt output reduces the need for continuous bus polling when an input changes state. Three hardware address pins, A0, A1, and A2, select the fixed I2C-bus address of the device. According to the NXP product page, as many as eight PCA9555 devices can share one bus when the address pins are configured differently. The PCA9555 also uses the same fixed bus address as the PCA9554, allowing the two device types to coexist on a bus in combinations that do not produce an address conflict. The 5.5 V maximum operating voltage and 400 kHz bus capability suit compact control boards, industrial modules, test equipment, and consumer accessories. The NXP part is identified with a 24-HVQFN exposed-pad package, which keeps the footprint compact while providing a thermal and electrical connection to the PCB ground plane. The exact exposed-pad construction and recommended land pattern should be taken directly from the manufacturer datasheet and package drawing. Designers should confirm the I2C pull-up resistance, address-strapping levels, output-drive requirements, and exposed-pad connection in the manufacturer datasheet. Because this device expands ports rather than providing level shifting, its VDD and VSS pins must match the logic environment used by the host and attached peripherals. Care is also required when connecting outputs to loads that source current independently.

RFQ پەیوەندی
PCA9555DB - 16-Bit I2C GPIO Expander with Interrupt | NXP
PCA9555DB

PCA9555DB - 16-Bit I2C GPIO Expander with Interrupt | NXP

The NXP Semiconductors PCA9555DB is a 16-bit I2C-bus and SMBus GPIO expander with interrupt, operating from 2.3 V to 5.5 V in a 24-pin SSOP package. It provides 16 general-purpose parallel input/output lines, supports 400 kHz serial operation, and uses an open-drain active-low interrupt output. What is an I2C GPIO expander? An I2C GPIO expander is an interface IC that adds parallel digital input and output capability to a controller with limited pins. The PCA9555 belongs to the I/O expander, parallel I/O, interface IC, and semiconductor hierarchy. Its two 8-bit ports connect a microcontroller or processor to switches, indicators, sensors, relays, and other external circuits while keeping the host-side connection compact. Key features include 16 configurable GPIO lines, separate input and output port registers, polarity inversion registers, 5 V tolerant I/O ports, and low standby-current consumption with a maximum of 1 uA. The 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V systems. Its open-drain interrupt output allows multiple change events to be combined on a shared host interrupt line. The device uses a two-wire I2C/SMBus interface with serial clock and serial data connections. A configurable seven-bit address supports multiple expanders on one bus, while 100 kHz and 400 kHz operating modes are identified in the provided NXP-family search data. The SSOP-24 package provides a conventional through-board surface-mount form factor with a 1.0 mm pitch. Typical applications include industrial control panels, programmable relay boards, LED status systems, keypad interfaces, sensor aggregation, and compact embedded control systems. The PCA9555DB is especially useful when a host controller needs more GPIO than its package or board-level pin budget can provide. Designers should confirm address selection, pull-up requirements, input thresholds, output-drive capability, and interrupt polarity against the manufacturer datasheet. Because the verified data does not include pricing or a complete pin-level table, those details remain explicitly unverified rather than inferred.

RFQ پەیوەندی
PCA9555DBR - 16-Bit I2C GPIO Expander with Interrupt | NXP (Tape & Reel)
PCA9555DBR

PCA9555DBR - 16-Bit I2C GPIO Expander with Interrupt | NXP (Tape & Reel)

The NXP Semiconductors PCA9555DBR is a 16-bit I2C-bus and SMBus GPIO expander with interrupt, operating from 2.3 V to 5.5 V in a 24-pin SSOP package. It provides 16 general-purpose parallel input/output lines, supports 400 kHz serial operation, and uses an open-drain active-low interrupt output. What is an I2C GPIO expander? An I2C GPIO expander is an interface IC that adds parallel digital input and output capability to a controller with limited pins. The PCA9555 belongs to the I/O expander, parallel I/O, interface IC, and semiconductor hierarchy. Its two 8-bit ports connect a microcontroller or processor to switches, indicators, sensors, relays, and other external circuits while keeping the host-side connection compact. Key features include 16 configurable GPIO lines, separate input and output port registers, polarity inversion registers, 5 V tolerant I/O ports, and low standby-current consumption with a maximum of 1 uA. The 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V systems. Its open-drain interrupt output allows multiple change events to be combined on a shared host interrupt line. The device uses a two-wire I2C/SMBus interface with serial clock and serial data connections. A configurable seven-bit address supports multiple expanders on one bus, while 100 kHz and 400 kHz operating modes are identified in the provided NXP-family search data. The SSOP-24 package provides a conventional through-board surface-mount form factor with a 1.0 mm pitch. Typical applications include industrial control panels, programmable relay boards, LED status systems, keypad interfaces, sensor aggregation, and compact embedded control systems. The PCA9555DBR is especially useful when a host controller needs more GPIO than its package or board-level pin budget can provide. Designers should confirm address selection, pull-up requirements, input thresholds, output-drive capability, and interrupt polarity against the manufacturer datasheet. Because the verified data does not include pricing or a complete pin-level table, those details remain explicitly unverified rather than inferred.

RFQ پەیوەندی
PCA9555DW - 16-Bit I/O Expander, 2.3-5.5V | TI
PCA9555DW

PCA9555DW - 16-Bit I/O Expander, 2.3-5.5V | TI

The Texas Instruments PCA9555DW is a 16-bit I2C/SMBus I/O expander with interrupt, weak pull-up and configuration registers, operating from 2.3V to 5.5V and supporting up to 400kHz bus operation. It is packaged in a 24-pin SOIC (DW) package rated for -40°C to +85°C operation. The device adds two 8-bit parallel I/O ports to a bus controller without requiring a dedicated GPIO controller. An I/O expander is an interface IC that translates serial I2C or SMBus commands into parallel digital input or output signals. In the signal-chain hierarchy, it sits between a microcontroller or embedded processor and external panel buttons, LEDs, relays, sensors, or other digital peripherals. The PCA9555 combines addressable input and output ports with configurable polarity and an interrupt mechanism, reducing host pin count while preserving a simple two-wire control path. Key features include 16 configurable I/O lines, active-low open-drain interrupt output, weak pull-up configuration registers, and compatibility with both I2C and SMBus systems. Each port can be configured independently as input or output through the device registers. Input polarity inversion and output drive behavior can be programmed, allowing the same device to support active-low buttons, indicator circuits, and other digital interfaces. The PCA9555 is controlled through a serial interface using address-select pins and command registers. This makes firmware configuration straightforward when the host already supports I2C. The 400kHz operating capability helps reduce control-loop time when multiple expander devices are present or when the system needs responsive input polling. The device is intended for systems where distributed GPIO expansion is preferable to expanding the host package. Typical applications include industrial control panels, keypad and button interfaces, LED indication, appliance controls, instrumentation, and embedded systems requiring more GPIO than the host microcontroller provides. The 2.3V to 5.5V supply range supports both low-voltage and conventional 5V digital systems. The 24-pin SOIC package also makes the device suitable for through-hole assembly and conventional PCB layouts. When designing around the PCA9555, account for the I2C bus pull-up requirement, correct address selection, and the electrical limits of each output. The interrupt pin should be configured with an appropriate pull-up because it is open-drain and active low. Firmware should also define startup states and port directions before external circuitry becomes active. This page summarizes the verified device identity, package, operating range, interface features, and design implications available for PCA9555DW selection. This information distinguishes the PCA9555DW from generic 8-bit expanders by combining a 16-bit parallel interface, configurable weak pull-ups, polarity control, and interrupt support in a 2.3V to 5.5V SOIC device.

RFQ پەیوەندی
PCA9555DWR - 16-Bit I/O Expander, 2.3-5.5V | TI (Tape & Reel)
PCA9555DWR

PCA9555DWR - 16-Bit I/O Expander, 2.3-5.5V | TI (Tape & Reel)

The Texas Instruments PCA9555DWR is a 16-bit I2C/SMBus I/O expander with interrupt, weak pull-up and configuration registers, operating from 2.3V to 5.5V and supporting up to 400kHz bus operation. It is packaged in a 24-pin SOIC (DW) package rated for -40°C to +85°C operation. The device adds two 8-bit parallel I/O ports to a bus controller without requiring a dedicated GPIO controller. An I/O expander is an interface IC that translates serial I2C or SMBus commands into parallel digital input or output signals. In the signal-chain hierarchy, it sits between a microcontroller or embedded processor and external panel buttons, LEDs, relays, sensors, or other digital peripherals. The PCA9555 combines addressable input and output ports with configurable polarity and an interrupt mechanism, reducing host pin count while preserving a simple two-wire control path. Key features include 16 configurable I/O lines, active-low open-drain interrupt output, weak pull-up configuration registers, and compatibility with both I2C and SMBus systems. Each port can be configured independently as input or output through the device registers. Input polarity inversion and output drive behavior can be programmed, allowing the same device to support active-low buttons, indicator circuits, and other digital interfaces. The PCA9555 is controlled through a serial interface using address-select pins and command registers. This makes firmware configuration straightforward when the host already supports I2C. The 400kHz operating capability helps reduce control-loop time when multiple expander devices are present or when the system needs responsive input polling. The device is intended for systems where distributed GPIO expansion is preferable to expanding the host package. Typical applications include industrial control panels, keypad and button interfaces, LED indication, appliance controls, instrumentation, and embedded systems requiring more GPIO than the host microcontroller provides. The 2.3V to 5.5V supply range supports both low-voltage and conventional 5V digital systems. The 24-pin SOIC package also makes the device suitable for through-hole assembly and conventional PCB layouts. When designing around the PCA9555, account for the I2C bus pull-up requirement, correct address selection, and the electrical limits of each output. The interrupt pin should be configured with an appropriate pull-up because it is open-drain and active low. Firmware should also define startup states and port directions before external circuitry becomes active. This page summarizes the verified device identity, package, operating range, interface features, and design implications available for PCA9555DWR selection. This information distinguishes the PCA9555DWR from generic 8-bit expanders by combining a 16-bit parallel interface, configurable weak pull-ups, polarity control, and interrupt support in a 2.3V to 5.5V SOIC device.

USD $2.46 لە کۆگادایە
PCA9555N - 16-Bit I2C GPIO Expander | NXP Semiconductors
PCA9555N

PCA9555N - 16-Bit I2C GPIO Expander | NXP Semiconductors

The NXP Semiconductors PCA9555N is a 24-pin CMOS 16-bit parallel GPIO expander for I2C-bus and SMBus systems, providing individual input, output, and polarity-inversion control in an SO24 package. It supports a 2.3 V to 5.5 V operating supply range, offers 5 V I/O tolerance, and communicates at rates up to 400 kHz. An I/O expander is a peripheral-controller IC that increases the number of general-purpose input/output pins available to a host microcontroller or processor. The PCA9555N belongs to the GPIO expander hierarchy, where an I2C-controlled interface manages 16 parallel digital lines while the host configures direction and reads input state through serial registers. This reduces the pin count required on processors used in compact industrial, communications, and consumer equipment. The device divides its 16 I/O lines into two eight-bit ports and includes separate registers for input, output, polarity inversion, and configuration. Each bit can be selected independently as an input or output. The NXP product page specifically identifies higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, and small packaging as improvements over earlier family members. An interrupt output supports event-driven monitoring of input pins. The PCA9555N uses an I2C-bus or SMBus serial interface for configuration and data transfer. Its address pins support multiple devices on the same bus, while the host reads the input register to determine the state of lines configured as inputs. The output register controls lines configured as outputs, and the polarity-inversion register allows active-high or active-low interpretation of input signals without changing external hardware. Typical uses include expanding keypad or control-panel inputs, monitoring digital sensor and alarm lines, driving LED or relay-control inputs, supporting display and interface boards, and adding general-purpose digital I/O to compact embedded systems. The 400 kHz bus capability is useful for moderate-rate control traffic rather than high-bandwidth sensor streaming. Designers should treat address selection, pull-up resistors, and output-pin defaults as important PCB decisions. Confirm the complete pin description in the manufacturer datasheet before assigning tracks, and validate the intended logic levels against the device’s 5 V I/O tolerance. Because the device is specified as CMOS and bus-based, correct decoupling and clean routing help preserve reliable communication. This page combines the manufacturer’s functional description, verified source links, drop-in cross-reference findings, package-level guidance, and practical application analysis to support component selection, schematic review, and sourcing decisions for the PCA9555N.

RFQ پەیوەندی
PCA9555PW - 16-Bit I2C GPIO Expander | NXP Semiconductors
PCA9555PW

PCA9555PW - 16-Bit I2C GPIO Expander | NXP Semiconductors

The NXP Semiconductors PCA9555PW is a 24-pin CMOS I/O expander with 16 general-purpose parallel input/output ports for I2C-bus and SMBus systems, operating from 2.3 V to 5.5 V in a 24-pin TSSOP package. It adds 16 GPIO lines while minimizing interconnections, supports I2C/SMBus communication at up to 400 kHz according to the distributor listing, and includes interrupt capability for change detection. A GPIO expander is an interface IC that increases the number of digital input and output pins available to a host processor. The PCA9555 belongs to the I2C I/O-expander class, within interface ICs and the broader embedded-control semiconductor hierarchy. Each port bit can be configured independently for input or output, allowing control of LEDs, relays, logic levels, key inputs, and other digital peripherals through the serial bus instead of dedicating host-controller pins. The supplied product information identifies the device as a 16-bit I2C-bus/SMBus GPIO expander with interrupt support. Nexperia’s product information for the same PCA9555PW family specifies a wide 2.3 V to 5.5 V operating range and default GPIO pull-up resistors. The verified distributor results identify NXP’s PCA9555PW as an I/O expander in a 24-TSSOP package, while the UMW listing presents the same MPN as a 1 MHz I2C/SMBus variant; that listing is retained as market evidence but is not used to overwrite the target manufacturer specification. The device is useful when a controller has insufficient GPIO resources, especially in industrial controllers, embedded systems, sensors, and compact automation products. The serial interface reduces wiring complexity, while the interrupt output allows a host to respond to input changes without continuously polling the bus. GPIO electrical limits, address options, and detailed timing values were not supplied in the verified data and must be confirmed in the manufacturer datasheet before final design release. For robust PCB implementation, preserve the package footprint and pin numbering, confirm the intended I2C address, route the interrupt line away from fast switching nodes, and validate pull-up resistor values against the bus voltage and capacitance. Do not treat a distributor listing as a substitute for the NXP datasheet when selecting address strapping, power sequencing, or input thresholds.

RFQ پەیوەندی
PCA9555PWE4 - 16-Bit 400kHz I/O Expander | Texas Instruments
PCA9555PWE4

PCA9555PWE4 - 16-Bit 400kHz I/O Expander | Texas Instruments

The Texas Instruments PCA9555PWE4 is a 16-bit I2C and SMBus I/O expander operating from 2.3V to 5.5V at up to 400kHz, with an interrupt output and configuration registers in a 24-pin TSSOP package. It adds 16 general-purpose digital input or output ports to a host processor through the two-wire serial bus. An I/O expander is an interface IC that extends the number of controllable or readable digital lines available on a microcontroller or embedded processor. The PCA9555 belongs to the broader hierarchy of I2C interface controllers, peripheral interface ICs, and semiconductors. Its two 8-bit ports can be configured independently as inputs or outputs, while power-on reset and configuration registers establish the initial operating state. The key feature set includes 16 configurable I/O lines, a 2.3V to 5.5V supply range, a 400kHz I2C interface, an interrupt output, configuration registers, and weak pull-ups. The interrupt output allows the host to detect a change on an input port without continuously polling the device. This combination reduces host pin count and can simplify firmware event handling in distributed control systems. The PCA9555 registers port direction, polarity, and output data through the serial interface. Input port values reflect the corresponding input pins, while output port values control the output pins. Reset initializes the ports to their default state, giving the host a defined starting condition. The device also supports multiple fixed slave addresses, allowing separate expanders to share the same SDA and SCL bus when address straps are configured appropriately. Typical uses include industrial control modules, automated test equipment, appliance interfaces, LED control, keyboard or switch sensing, and general-purpose embedded I/O. The 24-TSSOP package keeps the device practical for compact controller boards, while its 2.3V to 5.5V operating range accommodates both 3.3V and 5V systems. Industrial-temperature operation extends suitability across factory, building, and instrumentation equipment. PCB design should keep SDA, SCL, and ground connections short, place pull-up resistors close to the bus master, and account for bus capacitance when choosing their values. Confirm address selection before routing multiple expanders on one bus, and use the interrupt line when change-driven updates are preferable to periodic polling. The 24-pin footprint requires careful TSSOP pad spacing and adequate clearance during assembly. This product page combines the device functions, interface limits, package details, candidate drop-in alternatives, and implementation guidance needed to evaluate the PCA9555PWE4 for an existing embedded design.

RFQ پەیوەندی
PCA9555PWR - 16-Bit I2C GPIO Expander | NXP Semiconductors (Tape & Reel)
PCA9555PWR

PCA9555PWR - 16-Bit I2C GPIO Expander | NXP Semiconductors (Tape & Reel)

The NXP Semiconductors PCA9555PWR is a 24-pin CMOS I/O expander with 16 general-purpose parallel input/output ports for I2C-bus and SMBus systems, operating from 2.3 V to 5.5 V in a 24-pin TSSOP package. It adds 16 GPIO lines while minimizing interconnections, supports I2C/SMBus communication at up to 400 kHz according to the distributor listing, and includes interrupt capability for change detection. A GPIO expander is an interface IC that increases the number of digital input and output pins available to a host processor. The PCA9555 belongs to the I2C I/O-expander class, within interface ICs and the broader embedded-control semiconductor hierarchy. Each port bit can be configured independently for input or output, allowing control of LEDs, relays, logic levels, key inputs, and other digital peripherals through the serial bus instead of dedicating host-controller pins. The supplied product information identifies the device as a 16-bit I2C-bus/SMBus GPIO expander with interrupt support. Nexperia’s product information for the same PCA9555PWR family specifies a wide 2.3 V to 5.5 V operating range and default GPIO pull-up resistors. The verified distributor results identify NXP’s PCA9555PWR as an I/O expander in a 24-TSSOP package, while the UMW listing presents the same MPN as a 1 MHz I2C/SMBus variant; that listing is retained as market evidence but is not used to overwrite the target manufacturer specification. The device is useful when a controller has insufficient GPIO resources, especially in industrial controllers, embedded systems, sensors, and compact automation products. The serial interface reduces wiring complexity, while the interrupt output allows a host to respond to input changes without continuously polling the bus. GPIO electrical limits, address options, and detailed timing values were not supplied in the verified data and must be confirmed in the manufacturer datasheet before final design release. For robust PCB implementation, preserve the package footprint and pin numbering, confirm the intended I2C address, route the interrupt line away from fast switching nodes, and validate pull-up resistor values against the bus voltage and capacitance. Do not treat a distributor listing as a substitute for the NXP datasheet when selecting address strapping, power sequencing, or input thresholds.

RFQ پەیوەندی
PCA9557D - 8-Bit I2C/SMBus I/O Expander with Reset | TI (Tape & Reel)
PCA9557D

PCA9557D - 8-Bit I2C/SMBus I/O Expander with Reset | TI (Tape & Reel)

The Texas Instruments PCA9557D is an 8-bit I2C/SMBus I/O expander with configuration registers and a hardware reset input, operating from a 2.3 V to 5.5 V supply and packaged in a 16-pin SOIC (DR) footprint. The device provides general-purpose remote I/O expansion through the two-line bidirectional I2C bus (SCL and SDA) at speeds up to 400 kHz (Fast Mode). Each of the eight I/O pins can be independently configured as either an input or output, and the on-chip register set lets a host microcontroller read pin state and drive output latches over the same two-wire serial link. An I/O expander is a type of digital interface IC that sits on an I2C/SMBus and exposes additional GPIO to a host processor that has too few pins for its application. It belongs to the broader family of parallel-port expanders and, hierarchically, to peripheral ICs > interface ICs > digital logic ICs. Compared to a discrete shift-register approach, an I2C expander uses fewer host pins (only SCL and SDA), supports multi-drop addressing on the bus, and consumes very low standby current. Key features of the PCA9557D include 1 uA maximum standby current, 5 V tolerant I/O, hardware reset via the RESET pin, software reset through the I2C general-call address, and individually configurable I/O direction. The device supports up to eight slave addresses set by A0-A2 (within the PCA9557 family address space) so multiple expanders can share a single bus. An interrupt output (INT) signals the host when any input changes state, avoiding polling overhead. The PCA9557D uses a CMOS process with internal power-on reset and a low-impedance output structure capable of sourcing/sinking 10 mA per bit at 5 V, enabling direct LED drive in many cases. SMBus-alert and hardware-pin reset combine for robust multi-device control. According to the TI PCA9557 datasheet (SCPS155D-family), the device is pin-compatible with the PCA9554/PCA9534/PCF8574 series in 16-pin SOIC. Typical applications include server chassis management, industrial control panels, portable instrumentation, ACPI GPIO expansion on motherboards, keypad scanning, and LED driving on plug-in cards. Designers choose it when they need to expand a microcontroller's GPIO count over I2C while maintaining low standby power. When designing with this device, always include pull-up resistors on SCL, SDA, RESET, and INT per the I2C/SMBus specification (typically 2.2 k to 10 k depending on bus capacitance and speed). Decouple VCC with a 0.1 uF ceramic capacitor placed within 5 mm of the supply pin to suppress switching transients. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving buyers a one-stop comparison source.

RFQ پەیوەندی
PCA9557DB - 8-Bit I2C I/O Expander | Texas Instruments
PCA9557DB

PCA9557DB - 8-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCA9557DB is an 8-bit I2C/SMBus low-power I/O expander with a 2.3 V to 5.5 V operating range, 400 kHz bus speed, and a 16-pin SSOP package. It provides eight remotely controlled general-purpose I/O lines and includes dedicated reset and configuration registers. The device is designed to extend the number of available digital inputs and outputs for embedded systems without requiring a parallel GPIO port on the host controller. An I/O expander is a type of interface IC that connects a serial bus to additional digital lines. The PCA9557DB belongs to the I2C/SMBus GPIO expander family, combining a serial interface controller, configuration registers, and eight quasi-bidirectional I/O ports. Its I2C and SMBus compatibility places it within the broader interface-IC and embedded-control hierarchy, where it can reduce the GPIO requirements of a microcontroller or processor. The PCA9557DB supports a 2.3 V to 5.5 V supply range, allowing use with both 3.3 V and 5 V systems. Its serial interface operates up to 400 kHz, while eight I/O pins provide flexible control of LEDs, logic inputs, or external interface signals. Dedicated configuration registers allow software to identify input or output direction, while the reset and configuration registers support deterministic peripheral initialization and bus management. The device communicates through serial clock and serial data lines, with address selection provided by hardware pins. The SSOP package is a compact surface-mount option, and the verified distributor information identifies the DB ordering variant as a 16-pin SSOP measuring approximately 0.209 inches, or 5.30 mm, in width. Because this is a general-purpose interface device rather than a power semiconductor, a safe operating area chart is not applicable. Typical uses include low-power MCU systems, industrial control modules, sensor-hub boards, LED indicators, and small embedded platforms requiring eight additional digital lines. The PCA9557DB is particularly useful when conserving controller pins is more important than high-speed parallel GPIO operation. Because the serial interface is shared with other bus devices, address configuration, pull-up requirements, and software initialization must be coordinated during board design. Designers should confirm the exact pin functions and electrical limits in the manufacturer datasheet before layout. Bus pull-ups, input thresholds, power sequencing, and the states of I/O pins during reset require careful review. Software should configure each port direction and initial output value before enabling the associated external circuitry to prevent unintended switching. This page consolidates verified manufacturer and distributor information, documents missing electrical parameters transparently, and identifies only same-package drop-in candidates supported by the supplied cross-reference evidence. It also adds application guidance and engineering checks that are not available from a distributor listing alone.

RFQ پەیوەندی
PCA9557DBR - 8-Bit I2C I/O Expander | Texas Instruments
PCA9557DBR

PCA9557DBR - 8-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCA9557DBR is an 8-bit I2C and SMBus low-power I/O expander with reset and configuration registers, operating from 2.3 V to 5.5 V in a 16-pin SSOP package. It adds eight configurable digital I/O lines to a host controller while using only an I2C or SMBus interface for communication. The manufacturer describes the device as a remote expansion solution for systems whose external parallel I/O requirements exceed the available pins of the main controller. An I/O expander is an interface IC that extends the number of digital input or output lines available to a processor, microcontroller, or other bus master. Its place in the hardware hierarchy is I/O expander → interface controller → interface IC → semiconductor. The PCA9557DBR combines this bus interface with an 8-bit parallel port, making it useful for reducing package size, simplifying control wiring, and adding peripheral connections without requiring a larger host controller. Key features include eight remotely controlled I/O lines, a two-wire I2C/SMBus-compatible interface with a stated bus speed of 400 kHz, and dedicated reset and configuration registers. According to the Texas Instruments product page, the device supports 2.3 V to 5.5 V VCC operation. These characteristics allow the same expander to be used in low-voltage embedded systems as well as conventional 5 V industrial, consumer, and communications equipment without changing the interface arrangement. The device operates as a bus-addressed peripheral, with address and port behavior established through its configuration functions. Because its eight ports are controlled through a serial bus, software can read or change external logic levels without dedicating eight host GPIO pins. The reset function provides a defined initialization route for the expansion logic, while the configuration register supports controlled setup of the I/O behavior. Exact register addresses, polarity settings, and electrical limits should be confirmed in the manufacturer datasheet before firmware or PCB release. Typical uses include low-pin-count embedded controllers, industrial control modules, sensor and actuator interfaces, LED or switch input expansion, and communication equipment needing additional discrete digital lines. The PCA9557DBR is particularly useful where a design must retain a compact host package while adding an eight-bit parallel interface. Because the peripheral communicates over I2C or SMBus, it also avoids the larger routing burden associated with another direct host-to-I/O connection. When laying out a board, place the device close to the connector or controlled circuitry it serves, keep I2C routing short, and provide the required pull-up resistors on SCL and SDA. Account for the device address when multiple expanders share a bus, and use the reset input for a deterministic hardware startup path. Verify bus capacitance, pull-up resistance, voltage compatibility, and logic-level thresholds against the final system conditions. This page consolidates the verified manufacturer description, distributor availability and pricing references, package details, and practical implementation guidance. It also distinguishes confirmed replacement information from parameters that still require datasheet-level verification, helping engineers evaluate the PCA9557DBR without confusing electrically similar devices with verified drop-in choices.

RFQ پەیوەندی
PCA9557DGVR - 8-Bit I2C I/O Expander | Texas Instruments
PCA9557DGVR

PCA9557DGVR - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCA9557DGVR is an 8-bit I2C and SMBus low-power I/O expander with reset and configuration registers, operating from 2.3 V to 5.5 V and supporting bus speeds up to 400 kHz. It is packaged in a 16-pin TVSOP and provides eight configurable quasi-bidirectional I/O lines through a two-wire serial interface. An I/O expander extends the number of digital input and output pins available to a host controller without adding a dedicated parallel-port bus. The I2C interface carries commands and data over two shared wires, while SMBus compatibility supports common embedded control architectures. This places the PCA9557 within the hierarchy of interface IC, bus expander, GPIO controller, and power-management-aware embedded peripheral. The PCA9557 combines eight independently configurable I/O ports, an active-low reset input, and dedicated configuration registers. Its low standby-current capability, rated at 1 µA maximum in the manufacturer datasheet, makes it suitable for systems that spend significant time in a reduced-power state. The 2.3 V to 5.5 V operating range covers common low-voltage logic systems and 5 V peripheral boards. The active-low RESET input allows a system controller to restore the power-on register state and initialize the I2C or SMBus state machine without removing power from the device. Configuration registers provide centralized control of the port behavior, while the eight ports can be individually programmed for input or output operation. The 400 kHz bus capability provides a practical balance between transfer throughput, wiring simplicity, and low system complexity. Typical uses include industrial control panels, programmable LED indicators, key scanners, sensor and relay interfaces, and compact embedded control boards. The PCA9557 is especially useful when the primary microcontroller or application processor has too few GPIO pins for switches, indicators, interlocks, or remote digital I/O. Design the PCB with short I2C traces, pull-up resistors on SDA and SCL, and a deliberate address assignment through the A0, A1, and A2 pins. Account for the active-low reset signal, validate output drive current for each connected load, and keep bus capacitance and voltage rise time within the limits stated in the manufacturer datasheet. This page combines the manufacturer's functional description, exact ordering information, package details, interface characteristics, and application-oriented engineering guidance. It also distinguishes verified drop-in alternatives from devices that require footprint or function review, helping engineers shorten sourcing and design-in work.

RFQ پەیوەندی
PCA9557DR - 8-Bit I2C/SMBus I/O Expander with Reset | TI
PCA9557DR

PCA9557DR - 8-Bit I2C/SMBus I/O Expander with Reset | TI

The Texas Instruments PCA9557DR is an 8-bit I2C/SMBus I/O expander with configuration registers and a hardware reset input, operating from a 2.3 V to 5.5 V supply and packaged in a 16-pin SOIC (DR) footprint. The device provides general-purpose remote I/O expansion through the two-line bidirectional I2C bus (SCL and SDA) at speeds up to 400 kHz (Fast Mode). Each of the eight I/O pins can be independently configured as either an input or output, and the on-chip register set lets a host microcontroller read pin state and drive output latches over the same two-wire serial link. An I/O expander is a type of digital interface IC that sits on an I2C/SMBus and exposes additional GPIO to a host processor that has too few pins for its application. It belongs to the broader family of parallel-port expanders and, hierarchically, to peripheral ICs > interface ICs > digital logic ICs. Compared to a discrete shift-register approach, an I2C expander uses fewer host pins (only SCL and SDA), supports multi-drop addressing on the bus, and consumes very low standby current. Key features of the PCA9557DR include 1 uA maximum standby current, 5 V tolerant I/O, hardware reset via the RESET pin, software reset through the I2C general-call address, and individually configurable I/O direction. The device supports up to eight slave addresses set by A0-A2 (within the PCA9557 family address space) so multiple expanders can share a single bus. An interrupt output (INT) signals the host when any input changes state, avoiding polling overhead. The PCA9557DR uses a CMOS process with internal power-on reset and a low-impedance output structure capable of sourcing/sinking 10 mA per bit at 5 V, enabling direct LED drive in many cases. SMBus-alert and hardware-pin reset combine for robust multi-device control. According to the TI PCA9557 datasheet (SCPS155D-family), the device is pin-compatible with the PCA9554/PCA9534/PCF8574 series in 16-pin SOIC. Typical applications include server chassis management, industrial control panels, portable instrumentation, ACPI GPIO expansion on motherboards, keypad scanning, and LED driving on plug-in cards. Designers choose it when they need to expand a microcontroller's GPIO count over I2C while maintaining low standby power. When designing with this device, always include pull-up resistors on SCL, SDA, RESET, and INT per the I2C/SMBus specification (typically 2.2 k to 10 k depending on bus capacitance and speed). Decouple VCC with a 0.1 uF ceramic capacitor placed within 5 mm of the supply pin to suppress switching transients. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving buyers a one-stop comparison source.

RFQ پەیوەندی
PCA9557DT - 8-Bit I2C I/O Expander | Texas Instruments
PCA9557DT

PCA9557DT - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments PCA9557DT is an 8-bit I2C and SMBus low-power I/O expander with reset and configuration registers, a 2.3 V to 5.5 V operating supply range, and a maximum bus clock frequency of 400 kHz. It is packaged as a 16-pin SOIC in the DT ordering configuration. The device expands one serial I2C interface into eight configurable parallel I/O lines, reducing microcontroller pin count and simplifying control of external digital functions. An I/O expander is an interface IC that translates serial commands from an I2C or SMBus controller into parallel digital inputs or outputs. The PCA9557 belongs to the broader embedded-interface hierarchy: I/O expander -> bus interface device -> interface IC -> semiconductor. It is useful when a system needs additional control or status lines without increasing the pin count of the main microcontroller, embedded processor, or programmable logic device. Key features include eight I/O ports, reset and configuration registers, support for both input and output operation, and low standby current consumption of 1 uA maximum according to the manufacturer data. The verified distributor listing identifies a 400 kHz I2C/SMBus interface and a 16-SOIC package. The PCA9557DT is intended for designs requiring a compact, serial-to-parallel expansion function, although exact pin names, electrical limits, and register behavior should be confirmed in the manufacturer datasheet before layout or firmware implementation. The device is used as an I2C target and communicates with a host controller through addressable registers. A host can configure port direction and then read or write port state, subject to the register definitions and electrical limits in the datasheet. Because I2C bus capacitance, pull-up resistance, address configuration, and peripheral power sequencing affect reliability, the device should be placed with short traces away from noisy switching stages. Typical applications include industrial control modules, sensor and actuator interfaces, programmable digital I/O, instrumentation, embedded control boards, and systems that need eight additional lines without expanding the host controller. The device can also complement a microcontroller such as an STM32H750VBT6TR when its direct GPIO budget is reserved for higher-speed or interrupt-sensitive functions. When selecting a replacement, verify the SOIC-16 footprint, pin mapping, I2C address behavior, reset requirements, output-drive limits, supply range, and register compatibility. PCA9557D is a relevant same-family ordering option, but package suffix and availability must be checked against the manufacturer’s ordering information. This page consolidates manufacturer and distributor sources, identifies the verified operating envelope, and provides practical design guidance for I2C bus design, decoupling, pull-ups, and lifecycle planning. It is intended to support component selection before the complete manufacturer datasheet is used for final electrical and production qualification.

RFQ پەیوەندی
PCA9557PW - 8-Bit I2C I/O Expander | NXP | 16-TSSOP
PCA9557PW

PCA9557PW - 8-Bit I2C I/O Expander | NXP | 16-TSSOP

The NXP Semiconductors PCA9557PW is an 8-bit I2C/SMBus parallel input/output expander operating from 2.3 V to 5.5 V, with a 400 kHz bus rate and a 16-pin TSSOP package. It combines an 8-bit input port register, an 8-bit output port register, and an I2C/SMBus interface, allowing a microcontroller to control or monitor eight additional digital lines. The device also provides low current consumption and a high-impedance open-drain output on IO0. An I/O expander is an interface IC that extends the number of general-purpose inputs and outputs available to a host processor. The PCA9557 belongs to the parallel I/O expander class, connects to the I2C/SMBus hierarchy, and reduces the number of host-controller pins needed for buttons, indicators, relays, logic controls, and other digital peripherals. Its operating voltage range supports both 3.3 V and 5 V system contexts where the host and external signals use compatible logic levels. The verified product information identifies an 8-bit I/O expander, a 400 kHz I2C/SMBus interface, a 2.3 V to 5.5 V VCC range, and a 16-TSSOP package. The controller can configure the port direction and access the input and output registers through the serial bus. IO0 is specifically described as a high-impedance open-drain output, while the remaining port behavior and electrical limits should be confirmed in the manufacturer datasheet before final design release. Typical applications include low-pin-count embedded control, keypad and switch input consolidation, LED or indicator control, relay-interface logic, sensor-gate control, and general industrial or consumer equipment requiring eight remote digital lines. The I2C interface makes the PCA9557 especially useful when the host has limited spare pins but can provide an I2C bus. Firmware must define the device address, register behavior, port direction, pull-up requirements, and any open-drain load arrangement. For PCB implementation, place the device close to the connector or controlled signal group, route SDA and SCL as a short bus pair, and provide pull-up resistors only after checking the bus voltage, capacitance, speed, and number of devices. Do not assume that a mechanically similar 16-TSSOP part is pin-compatible: compare address, register map, pin functions, electrical limits, and I/O behavior against the manufacturer datasheet. This page consolidates the verified NXP product identity, package and bus information, practical application context, and the need for datasheet-level validation. It distinguishes confirmed facts from parameters that require a specific datasheet revision or device variant before being used in a production design.

RFQ پەیوەندی
PCA9557PWR - 8-Bit I2C I/O Expander | NXP | 16-TSSOP (Tape & Reel)
PCA9557PWR

PCA9557PWR - 8-Bit I2C I/O Expander | NXP | 16-TSSOP (Tape & Reel)

The NXP Semiconductors PCA9557PWR is an 8-bit I2C/SMBus parallel input/output expander operating from 2.3 V to 5.5 V, with a 400 kHz bus rate and a 16-pin TSSOP package. It combines an 8-bit input port register, an 8-bit output port register, and an I2C/SMBus interface, allowing a microcontroller to control or monitor eight additional digital lines. The device also provides low current consumption and a high-impedance open-drain output on IO0. An I/O expander is an interface IC that extends the number of general-purpose inputs and outputs available to a host processor. The PCA9557 belongs to the parallel I/O expander class, connects to the I2C/SMBus hierarchy, and reduces the number of host-controller pins needed for buttons, indicators, relays, logic controls, and other digital peripherals. Its operating voltage range supports both 3.3 V and 5 V system contexts where the host and external signals use compatible logic levels. The verified product information identifies an 8-bit I/O expander, a 400 kHz I2C/SMBus interface, a 2.3 V to 5.5 V VCC range, and a 16-TSSOP package. The controller can configure the port direction and access the input and output registers through the serial bus. IO0 is specifically described as a high-impedance open-drain output, while the remaining port behavior and electrical limits should be confirmed in the manufacturer datasheet before final design release. Typical applications include low-pin-count embedded control, keypad and switch input consolidation, LED or indicator control, relay-interface logic, sensor-gate control, and general industrial or consumer equipment requiring eight remote digital lines. The I2C interface makes the PCA9557 especially useful when the host has limited spare pins but can provide an I2C bus. Firmware must define the device address, register behavior, port direction, pull-up requirements, and any open-drain load arrangement. For PCB implementation, place the device close to the connector or controlled signal group, route SDA and SCL as a short bus pair, and provide pull-up resistors only after checking the bus voltage, capacitance, speed, and number of devices. Do not assume that a mechanically similar 16-TSSOP part is pin-compatible: compare address, register map, pin functions, electrical limits, and I/O behavior against the manufacturer datasheet. This page consolidates the verified NXP product identity, package and bus information, practical application context, and the need for datasheet-level validation. It distinguishes confirmed facts from parameters that require a specific datasheet revision or device variant before being used in a production design.

RFQ پەیوەندی
PCA9557RGVR - 8-Bit I2C I/O Expander | Texas Instruments
PCA9557RGVR

PCA9557RGVR - 8-Bit I2C I/O Expander | Texas Instruments

Texas Instruments PCA9557RGVR is an 8-bit I2C and SMBus low-power I/O expander with reset and configuration registers. It operates from 2.3 V to 5.5 V, supports I2C and SMBus communication at 400 kHz, and is packaged in a 16-pin 4 x 4 mm VQFN designated RGV. The device provides eight remotely controlled I/O lines while allowing a host controller to monitor and control additional peripherals over a serial bus. An I/O expander is an interface IC that extends the number of general-purpose inputs and outputs available to a microcontroller or other bus controller. Its place in the hierarchy is I/O expander, interface IC, integrated circuit, and semiconductor. Instead of dedicating multiple host pins to discrete control functions, a system can use the PCA9557RGVR to bring eight additional lines onto a shared two-wire bus. This can simplify routing and conserve host-controller I/O resources. The principal device features include an 8-bit I/O port, a 400 kHz I2C/SMBus interface, a 2.3 V to 5.5 V operating range, and dedicated reset and configuration registers. The reset function supports deterministic initialization of the port state, while the configuration registers allow the host software to define whether each port line operates as an input or output. These functions make the device useful in embedded systems where firmware must establish controlled states before external circuitry is enabled. The PCA9557RGVR is intended for low-power remote I/O expansion over an embedded serial bus. Its eight programmable lines can represent simple digital status inputs, control outputs, or a mixture of both. The 400 kHz bus rate provides a practical communication rate for many control systems while avoiding the wiring complexity of connecting eight separate host GPIO pins. The 2.3 V minimum operating voltage also places the device within the range commonly used by embedded processors and industrial controllers. Typical uses include industrial control panels, sensor and alarm interfaces, LED and relay control, compact embedded modules, and general-purpose controller expansion. In each case, the host communicates through I2C or SMBus and reads or writes the device registers. System software should define port directions, initialize outputs to a safe state, and use the reset input where deterministic startup behavior is required. Design consideration: place the PCA9557RGVR close to the connectors and peripherals it controls to keep I/O traces short, while routing the I2C bus with appropriate pull-up arrangements. Account for the device's 5.5 V maximum operating voltage and ensure that connected peripherals cannot back-power the port lines during reset. Firmware must also preserve the configured operating state whenever a reset is initiated. This product page combines the manufacturer's exact orderable-part information with practical guidance on reset handling, bus implementation, port configuration, PCB placement, and drop-in replacement evaluation. It helps engineers identify the correct 4 x 4 mm RGV package, verify the operating range and bus speed, and compare the available substitution evidence before committing to a design.

RFQ پەیوەندی
PCA9564D - 400 kHz Parallel-to-I2C Controller | NXP Semiconductors
PCA9564D

PCA9564D - 400 kHz Parallel-to-I2C Controller | NXP Semiconductors

The NXP Semiconductors PCA9564D is a parallel-bus to I2C-bus controller with a 2.3 V to 3.6 V operating supply range and a 400 kHz I2C interface in a 20-pin SO package. It converts data presented by an 8-bit parallel host interface into serial I2C transactions, allowing a microcontroller or processor with limited I2C capability to communicate with serial devices. A parallel-to-I2C bus controller is an interface IC that bridges two different digital communication methods. The parallel side accepts byte-oriented data and associated control signals, while the I2C side generates the clock and serial data required by an I2C bus. In the broader semiconductor hierarchy, the PCA9564D belongs to the interface-controller class, specifically parallel-bus-to-I2C-bus conversion. The verified device information identifies a controller type of parallel bus to I2C bus, a 2.3 V minimum supply voltage, a 3.6 V maximum supply voltage, and approximately 6 mA supply current. The associated 20-pin SO package occupies a 7.50 mm body width. These characteristics make the device applicable to embedded control systems that need an efficient bridge between a parallel CPU or programmable-logic interface and a 400 kHz I2C peripheral bus. The 400 kHz bus capability provides faster serial transfer than the traditional 100 kHz I2C rate while retaining compatibility with the established two-wire interface. The device can therefore reduce the number of serial transactions required when communicating with slower I2C peripherals, provided the selected peripheral supports fast-mode operation and the complete bus meets the required timing and rise-time characteristics. Typical uses include industrial control systems, automated test equipment, programmable-logic controllers, embedded instruments, and communication peripherals. In each case, the controller separates the host-side byte-oriented data path from the serial peripheral bus, simplifying firmware and reducing the number of host I2C transactions when both sides are controlled by the same system. Designers should confirm the exact logical pin assignments, address configuration, and electrical characteristics in the manufacturer datasheet before laying out the PCB. The 2.3 V to 3.6 V supply range requires compatible pull-ups and signal levels across the entire parallel and I2C interface. PCB placement should minimize parallel-bus switching noise and provide a clean return path between the controller, supply network, and attached I2C devices. This page consolidates the verified device specifications, ordering variants, drop-in comparison, and practical interface-design guidance into one engineering-focused reference. It also distinguishes confirmed electrical facts from parameters that still require confirmation from the complete manufacturer datasheet before a new design is released to production.

RFQ پەیوەندی
PCA9564N - 400 kHz Parallel-to-I2C Controller | NXP
PCA9564N

PCA9564N - 400 kHz Parallel-to-I2C Controller | NXP

NXP Semiconductors PCA9564N is a bidirectional parallel-bus to I2C-bus controller designed to connect parallel microprocessor interfaces with I2C peripheral devices. It supports I2C transfer rates up to 400 kHz and is offered in a 20-pin DIP through-hole package. The device provides a practical interface bridge for systems in which a parallel processor bus must communicate with serial I2C peripherals. A parallel-to-I2C controller is an interface IC that translates data transactions between two different bus architectures. The parallel side presents a simple processor-oriented interface, while the I2C side provides standardized two-wire communication with sensors, memory devices, converters, and other peripherals. In the broader semiconductor hierarchy, the PCA9564N belongs to the interface-controller family within interface ICs and acts as a bridge between parallel microprocessor systems and serial bus devices. The principal features of the PCA9564N include bidirectional parallel-bus operation, I2C controller functionality, and a maximum I2C transfer rate of 400 kHz. Bidirectional operation allows the controller to participate in transactions in which information must move between the parallel host and connected I2C devices. Its 400 kHz capability suits general-purpose industrial embedded-control systems that require faster transfer rates than standard 100 kHz I2C operation while retaining a compact peripheral-controller architecture. The NXP manufacturer datasheet describes PCA9564N as a parallel-bus to I2C-bus controller. Its function is intended to simplify connection between parallel microprocessors and I2C devices without requiring each software stack to implement the complete bus conversion itself. Application-specific protocol overhead, addressing, interrupt handling, and timing behavior should be implemented and verified against the manufacturer pin-description and timing information before a production design is released. Typical applications include industrial instrument panels, embedded control modules, legacy peripheral expansion, data-acquisition equipment, and board-level systems that retain a parallel processor interface while adding I2C sensors or memory. The 20-DIP package is particularly suitable for through-hole industrial assemblies and prototypes where leaded-package handling is preferred over fine-pitch surface-mount assembly. For PCB implementation, follow the manufacturer datasheet pin-description table when assigning the parallel data lines, control signals, address inputs, clock, and I2C connections. Confirm pull-up requirements, decoupling, address selection, signal timing, and unused-pin treatment in the system schematic. Because the exact public pin map is not reproduced on this page, use the NXP datasheet as the authoritative source for board-layout signoff. This product record combines the manufacturer product-page description, the 400 kHz interface rate, package information, application guidance, and a structured engineering comparison with practical implementation notes. These details help engineers determine whether PCA9564N fits a through-hole parallel-to-I2C bridging requirement before reviewing detailed timing, electrical limits, and ordering information in the manufacturer documentation.

RFQ پەیوەندی
PCA9570GMH - 4-Bit I2C GPO Expander | NXP | XQFN-8
PCA9570GMH

PCA9570GMH - 4-Bit I2C GPO Expander | NXP | XQFN-8

NXP PCA9570GMH is a 4-bit general-purpose output expander that adds push-pull digital outputs to a host processor through an I2C-bus interface. It supports bus speeds up to 1 MHz while maintaining backward compatibility with Fast-mode at 400 kHz and Standard-mode at 100 kHz. The device is supplied in an 8-pin XQFN package measuring 1.6 mm by 1.6 mm and includes an exposed thermal pad according to the distributor listing. An I2C output expander is a semiconductor interface device that converts a serial two-wire bus into additional parallel control outputs. In the product hierarchy, the PCA9570GMH belongs to the I/O expander class, within interface ICs and logic ICs. Unlike a general-purpose input/output expander, the PCA9570 is a streamlined GPO device whose four outputs are configured as push-pull drivers. This makes it suitable for controlling loads that require a driven logic level rather than a high-impedance input. Key features include four general-purpose parallel outputs, 1 MHz I2C-bus operation, and compatibility with both 100 kHz and 400 kHz bus standards. The low-voltage CMOS construction targets processor-based and handheld battery-powered equipment. The small XQFN-8 footprint helps reduce board area when a controller has too few output pins for relays, indicators, logic enables, or other digital loads. The PCA9570GMH is a streamlined output-only expander, so its register and pin arrangement should be compared carefully with mixed input/output or bidirectional expanders before substitution. Its four push-pull outputs provide defined high and low states, making the device appropriate for simple control signals in consumer electronics, mobile accessories, battery-powered instruments, and compact embedded systems. In a typical design, the host connects SDA and SCL to the PCA9570GMH, writes the desired output pattern to the device register, and reads back the output states. The bus lines require pull-up resistors in accordance with the I2C specification. Because the package exposes a pad, the PCB layout should maximize copper area under the exposed pad to improve heat spreading. For power-sensitive designs, the quiescent current and output-driver loading should be checked against the system battery budget. Because every host controller needs a reliable I2C pull-up arrangement, verify the bus capacitance, pull-up resistance, and level-shifting requirements before layout release. Use the pin-connection and register details in the manufacturer datasheet when assigning PCB tracks.

RFQ پەیوەندی
PCA9571GUX - 8-Bit 1MHz I2C Output Expander | NXP
PCA9571GUX

PCA9571GUX - 8-Bit 1MHz I2C Output Expander | NXP

NXP Semiconductors PCA9571GUX is an 8-bit general-purpose parallel output expander for low-voltage processor and handheld applications, with I2C communication up to 1 MHz and a 12-pin XQFN package measuring 2 mm by 1.7 mm. The device operates in Standard-mode at 100 kHz, Fast-mode at 400 kHz, and 1 MHz modes on a lightly loaded bus with less than 100 pF capacitance. An I2C output expander is an interface IC that adds parallel digital outputs to a serial bus. The hierarchy runs from I2C output expander to GPIO expander, interface expander, and semiconductor. It is useful when a processor has too few general-purpose output pins to control multiple discrete loads while the system architecture requires a shared serial control bus. The PCA9571GUX provides eight general-purpose parallel outputs and supports 1 MHz I2C operation while retaining backward compatibility with 100 kHz Standard-mode and 400 kHz Fast-mode buses. Backward compatibility allows the same device to operate alongside slower peripherals on a shared bus, although total bus capacitance, pull-up selection, and signal-integrity margin remain system-level constraints. The streamlined output-only architecture distinguishes this device from bidirectional I/O expanders. It does not provide input pins for state readback, so its primary function is command and control rather than monitoring external logic levels. The 2 mm by 1.7 mm XQFN package supports compact designs where board area is important, although the fine-pitch footprint requires careful PCB assembly and inspection. Typical applications include portable-device control, low-voltage processor systems, battery-powered equipment, and systems that need multiple parallel outputs driven over I2C. Product family members can be useful in portable and mobile equipment, industrial controllers, embedded systems, and peripheral-control designs where eight outputs reduce the number of direct host-controller connections. Designers should confirm the address configuration, output behavior, voltage limits, and pin mapping in the manufacturer datasheet before finalizing a PCB. The 1 MHz operating rate is intended for a lightly loaded bus below 100 pF; pull-up resistance, cable length, peripheral capacitance, and signal rise time must be evaluated together when the bus includes long traces or additional devices. This page organizes the PCA9571GUX function, interface characteristics, package constraints, application guidance, comparison points, and replacement criteria so that engineers can assess the device alongside other I2C output-expansion options before committing a board layout.

RFQ پەیوەندی
PCA9600D - 1MHz Dual I2C Bus Buffer | NXP Semiconductors
PCA9600D

PCA9600D - 1MHz Dual I2C Bus Buffer | NXP Semiconductors

The NXP Semiconductors PCA9600D is a 1 MHz dual bidirectional I2C-bus buffer designed to isolate bus capacitance in point-to-point and multipoint systems supporting loads up to 4000 pF. It is housed in an 8-pin SOIC package and is a higher-speed implementation of the P82B96 bus-buffer concept. An I2C bus buffer, also called a bus repeater or bidirectional bus isolator, is an interface IC that separates a high-capacitance bus section from the controller-side bus. This separation reduces the capacitive loading seen by the master while preserving bidirectional clock and data signaling. In the power-management hierarchy, the PCA9600D is not a regulator; it is an interface IC within the broader I2C and bus-management semiconductor category. The PCA9600D provides two buffered bus channels, a maximum operating frequency of 1 MHz, and support for bus capacitance up to 4000 pF. Its bidirectional architecture allows each channel to carry clock and data signals in either direction. The device is identified as a dual bidirectional bus buffer and is listed in SO-8 packaging, making it appropriate for compact industrial, communications, consumer, and embedded control systems. Technically, the PCA9600 addresses the rise-time and data-integrity problems created when an I2C bus connects multiple branches or remote cable segments. Buffering one side from the other limits the capacitance directly driven by the controller. Because the buffer is non-latching, it remains transparent to normal I2C traffic rather than requiring a separate protocol or latched control state. The manufacturer describes the PCA9600 as a higher-speed alternative to the P82B96. Typical uses include extending an I2C controller to a remote sensor or display module, isolating high-capacitance backplanes, connecting two bus segments, and supporting point-to-point links between boards with different loading conditions. In these applications, the buffer is normally placed in series with the relevant SCL or SDA conductor, with pull-up resistors placed separately on each isolated segment. PCB implementation should keep each side of the buffer electrically distinct. Configure pull-up resistor networks independently on the controller-side and remote-side buses, maintain the device ground connection close to pin 1, and route each channel away from high-current switching nodes. Confirm rise time at the worst-case bus capacitance rather than assuming that a nominal 1 MHz operating rate applies to every wiring configuration. This page combines the NXP product description, manufacturer datasheet link, lifecycle information, capacity and frequency characteristics, package details, and application-specific engineering guidance. It also distinguishes true drop-in ordering variants from functional alternatives, helping engineers evaluate PCB reuse, bus capacitance, voltage compatibility, and sourcing constraints before selecting a replacement.

RFQ پەیوەندی
PCA9600D,118 - 1 MHz I2C-bus Buffer/ReDriver | NXP | 8-SO
PCA9600D,118

PCA9600D,118 - 1 MHz I2C-bus Buffer/ReDriver | NXP | 8-SO

The NXP PCA9600D,118 is a dual bidirectional bus buffer/ReDriver designed to isolate I²C-bus capacitance in point-to-point and multipoint applications up to 4000 pF. Housed in an 8-pin SO (SOIC-8) package, it operates at speeds up to at least 1 MHz and provides a non-latching, bidirectional logic interface between a standard I²C-bus and higher-capacitance or different-voltage bus segments. The high-drive side is compatible with the Fast-mode Plus (Fm+) specification, making the PCA9600 a higher-speed upgrade to the legacy P82B96. What is an I²C bus buffer? An I²C-bus buffer/ReDriver is a dedicated interface IC that sits between two bus segments to overcome the 400 pF capacitive limit of standard I²C. By isolating capacitance, a buffer allows engineers to extend bus length, add more nodes, use lower-cost cabling, or bridge between logic-voltage domains. Buffers/ReDrivers belong to the interface IC hierarchy: interface IC > bus buffer > I²C extender > signal conditioning, and are widely used in industrial backplanes, sensor arrays, and LED lighting chains where long cable runs would otherwise exceed the bus's RC budget. Key features of the PCA9600 include an operating supply voltage range from 2.5 V to 15 V on the low-voltage (standard I²C) side, with logic-level translation capability through the dual-rail architecture. The part is specified for -40 °C to +85 °C operation and offers high-impedance logic pins that prevent bus latching during plug-in or brown-out events. The device is bus-isolating rather than bus-repeating, so it cannot sink the I²C pull-up current from both sides simultaneously—designers must provide pull-ups on each side. Architecturally, the PCA9600 uses an internal pass-FET-style transmission gate with direction-sense amplifiers that detect which side is driving and steer current accordingly without requiring an external direction-control pin. The result is a drop-in, transparent bus extender that does not occupy an I²C address and does not appear as a node. Compared to discrete MOSFET plus pull-up solutions, the PCA9600 guarantees matched thresholds, controlled rise/fall times, and known hot-swap behavior across temperature. Common applications include industrial control backplanes, large-display LED driver chains, remote sensor arrays, and any system where the I²C master sits on one PCB and the slaves are several meters away on a cable or harness. The PCA9600D,118 ships on 13-inch tape and reel and is fully RoHS compliant, targeting high-reliability commercial and industrial designs. When designing with this part, pay close attention to the pull-up placement: each bus segment requires its own pull-up resistor sized for that segment's capacitance and the target rise time. Designers commonly pair the PCA9600 with 4.7 kΩ pull-ups on the master side and 1 kΩ to 2.2 kΩ pull-ups on the high-drive side to handle the larger bus capacitance.

RFQ پەیوەندی