بەرهەمەکان (5,100+)

PCA9601D,118 - 1MHz Fm+ I2C Bus Buffer SO-8 | NXP
PCA9601D118

PCA9601D,118 - 1MHz Fm+ I2C Bus Buffer SO-8 | NXP

The NXP PCA9601D,118 is a dual bidirectional I2C-bus buffer and repeater supporting operation to at least 1 MHz (Fast-mode Plus), with a wide 2.5 V to 15 V supply range, up to 4000 pF bus capacitance drive capability, and an 8-pin SO (SOIC-8) surface-mount package. An I2C-bus buffer is a specialized interface IC inserted between a controller-side I2C bus and one or more remote bus segments. Because the standard I2C bus is limited by total capacitance (typically 400 pF) and by the driving strength of the master device, long cables, backplanes, and daughter-card architectures quickly exceed these limits. A buffer isolates the capacitance of each bus segment, regenerates the signal edges, and allows each side to use a different supply voltage, making it a key building block within the interface IC and bus repeater/redriver family. Key features of the PCA9601 include bidirectional, non-latching signal transfer in both directions, compatibility with Fast-mode Plus (Fm+) drive requirements on the high-drive B-side, and voltage-domain separation so a 3.3 V controller bus can drive a 5 V, 12 V, or 15 V remote bus. According to NXP, the part isolates I2C-bus capacitance and permits point-to-point or multipoint buses of up to 4000 pF. Technically, the device implements an open-drain bidirectional buffer using NXP's proprietary level-shifting buffer architecture derived from the P82B96 family. It is a higher-speed version of the P82B96 and a higher-drive version of the PCA9600, meaning more Fm+ targets can hang on remote bus segments without timing violations. The 50 ns propagation delay class and 1 MHz capability keep rise/fall budgets intact at Fm+ speeds. Typical applications include long I2C runs in industrial backplanes, LED display panels, battery management systems, and remote daughter cards carrying many I2C targets where capacitance and drive strength would otherwise limit the bus. Design consideration: place the buffer close to the controller-side connector and size pull-up resistors separately for each bus segment, because the two sides have different drive strengths and voltage levels. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
PCA9601DPZ - 1MHz Dual I2C-Bus Buffer | NXP Semiconductors
PCA9601DPZ

PCA9601DPZ - 1MHz Dual I2C-Bus Buffer | NXP Semiconductors

The NXP Semiconductors PCA9601DPZ is a dual bidirectional I2C-bus buffer and repeater that isolates bus capacitance and drives loads up to 4000 pF, operating at speeds up to 1 MHz (Fast-mode Plus) in an 8-pin TSSOP surface-mount package. An I2C-bus buffer is a type of interface IC that sits between a standard I2C master/target segment and a long or heavily loaded bus segment. In the interface IC hierarchy (bus buffer -> signal repeater -> interface IC), its role is to regenerate signal edges and isolate capacitance, because the I2C specification limits total bus capacitance and rising-edge time. By splitting one bus into short segments, a buffer allows long cables, backplanes, and daughter-card interconnects that would otherwise violate I2C timing. Key features of the PCA9601 include 4000 pF bus drive capability, non-latching bidirectional logic that preserves the wired-AND I2C arbitration and clock-stretching behavior, and a high-drive side compatible with Fast-mode Plus (Fm+) specifications. It supports level translation between mixed-voltage bus segments (3.3V, 5V, and higher-voltage buffered sides), enabling communication between 3.3V and 5V systems while maintaining signal integrity and timing. The PCA9601 is architecturally a higher-speed version of the well-established P82B96 and a higher-drive version of the PCA9600. Its buffered, non-latching topology means the buffer never locks up during arbitration or repeated starts, a common failure mode of simpler repeater designs. The high drive strength allows many more Fast-mode Plus targets on remote daughter cards than an unbuffered bus could support. Typical applications include point-to-point and multipoint extension of I2C buses across cables and backplanes, isolating capacitance of remote daughter cards, mixed-voltage (3.3V/5V) system interfacing, and industrial or telecom equipment where many Fm+ targets must share a long bus. Devices such as the PCA8574, PCA9539, and PCA9538 I/O expanders are typical loads at the far end of a buffered segment. Design considerations: the PCA9601 specifies an operating temperature range of 0 C to 85 C, so it is intended for commercial and industrial indoor use rather than automotive-grade environments. Verify bus segment capacitance on both sides and follow the datasheet for pull-up sizing on the buffered side to meet Fm+ rise-time requirements. This page synthesizes distributor pricing context, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-10-20.

RFQ پەیوەندی
PCA9605D - 400 kHz I2C Bus Buffer | NXP Semiconductors
PCA9605D

PCA9605D - 400 kHz I2C Bus Buffer | NXP Semiconductors

The NXP Semiconductors PCA9605D is a monolithic CMOS two-wire bus buffer designed to extend I2C, SMBus, DDC, PMBus, and similar bus capacity. It operates at up to 400 kHz, buffers one SCL/SDA channel pair, supports a 2.7 V to 5.5 V supply range, and is offered in an 8-pin SOIC package. Its principal function is to regenerate buffered bus signals while electrically separating the source and load sides of the bus. An I2C bus buffer is an interface IC that divides a two-wire serial bus into two segments and isolates their electrical loading. The PCA9605D allows each segment to operate within its permissible bus capacitance, extending the usable bus when long cables, multiple branches, or additional peripheral loading would otherwise burden the controller. In the device hierarchy, it belongs to the I2C interface-buffer family, bus buffers and repeaters, interface ICs, and integrated circuits. The PCA9605D includes one buffered SDA channel and one buffered SCL channel. Operating voltage of 2.7 V to 5.5 V supports both 3.3 V and 5 V systems, while the 400 kHz maximum bus frequency covers standard- and fast-mode I2C communication. The monolithic CMOS implementation provides bidirectional signal buffering in an 8-pin SOIC package rated for industrial-temperature operation from -40 °C to +85 °C. The buffered architecture reduces the capacitive load presented to the upstream bus controller by placing the source-side and load-side segments behind the buffer. This can improve bus signal integrity when a design contains multiple branches, connector segments, or distributed sensors. The device is intended for bus segmentation rather than level translation, so the source and destination domains should use compatible logic voltage levels. Typical uses include industrial sensor networks, server-management buses, display-control interfaces, power-system PMBus connections, and embedded systems that divide I2C traffic across multiple PCB or cable segments. The buffer is also suitable for SMBus and DDC arrangements where the controller must communicate beyond the loading allowed by a direct bus connection. PCB implementation requires correct pull-up placement and short, clean routing between the controller, buffer, and downstream devices. Place the input-side pull-ups near the active bus controller and the output-side pull-ups near the buffered load, then keep both SDA and SCL routes short and away from switching-node and high-current paths. Verify rise-time, fall-time, capacitance, and timing margins with the complete board configuration. This product overview combines manufacturer application information, package and interface characteristics, commercial sourcing guidance, and practical PCB considerations for engineers evaluating the PCA9605D. Use the Request a Quote form on this page for current availability, lead time, and commercial terms.

RFQ پەیوەندی
PCA9614DP,118 - 2-Ch Fm+ Differential I2C Bus Buffer | NXP
PCA9614DP,118

PCA9614DP,118 - 2-Ch Fm+ Differential I2C Bus Buffer | NXP

The NXP PCA9614DP,118 is a 2-channel multipoint Fast-mode Plus (Fm+) differential I2C-bus buffer with 400 kHz buffered operation, dual-supply differential signaling, and a 10-pin TSSOP (DP) surface-mount package. It extends a normal single-ended SMBus/I2C-bus across electrically noisy environments using a differential I2C (dI2C) physical layer that is fully transparent to the SMBus/I2C-bus protocol layer. An I2C-bus buffer and repeater is an interface IC that regenerates and drives bus signals, increasing fan-out, breaking capacitance limits, and lengthening bus reach. Within the interface IC hierarchy, buffer ICs sit between an I2C master/peripheral and the physical wire, and differential buffers such as this one add a robust physical layer without changing the protocol, so standard controllers require no firmware changes. Key features include two independent buffer channels supporting multipoint dI2C links over long cables, an EN pin that places the device in an idle state to stop traffic propagation, and an internal pull-up on EN that holds the device enabled by default. The differential transmission rejects common-mode noise, making the link tolerant of ground potential differences between boards. Technically, the PCA9614 converts the single-ended SDA/SCL levels into a differential pair per channel at the buffer output side, and converts back to single-ended at the receiving end when paired with another differential buffer. Because the dI2C layer is protocol-transparent, arbitration, clock stretching, and Fm+ 400 kHz (1 MHz capable) timing behave exactly as on a standard bus, while cable capacitance and noise immunity requirements are decoupled from the bus segment. Typical applications include industrial automation bus extension, rack and backplane inter-board communication in servers, battery management systems in electrically noisy traction environments, and long-run I2C links between enclosures or display modules. A key design consideration is power sequencing of the dual supplies (VDD(A) on the single-ended side and VDD(B)/VL on the differential side); both must remain within the datasheet recommended operating conditions and EN should be held low during startup to prevent glitching. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with freshness data as of 2026-10-20.

RFQ پەیوەندی
PCA9615DPZ - 2-Ch I2C Fast-Mode Plus Diff Buffer | NXP
PCA9615DPZ

PCA9615DPZ - 2-Ch I2C Fast-Mode Plus Diff Buffer | NXP

The NXP Semiconductors PCA9615DPZ is a 2-channel multipoint Fast-mode Plus differential I2C-bus buffer with hot-swap logic, operating up to 1 MHz, housed in a 10-pin TSSOP (SOT552-1) package. It supports standard I2C, Fast-mode, and SMBus compatibility, with single-ended I2C on the card side up to 540 pF and differential I2C on the cable side supporting multi-drop bus up to 3 meters. The device uses an external DCEN pin to enable/disable the differential driver and operates from dual supplies, typically VDD(A) on the single-ended side and VDD(B) on the differential side. A signal buffer, repeater, or redriver is an active interface IC placed in-line on a bus to restore signal integrity when the load capacitance or physical distance exceeds the limit of the bus specification. In the I2C hierarchy, this part is a specialized bus extender/repeater that converts a single-ended SDA/SCL pair into a differential pair for transmission over twisted-pair or shielded cable, then converts back at the far end. This is essential in industrial control, automotive sensor backbones, and large backplane systems where standard I2C's capacitive limit (~400 pF) is insufficient. Key features of the PCA9615DPZ include differential transmission across a cable up to 3 meters at Fast-mode Plus speeds, hot-swap logic that allows the card to be inserted into a live backplane without disturbing the bus, wide supply range (2.7 V to 5.5 V on VDD(A) and 3.0 V to 5.5 V on VDD(B)), and AEC-Q100 qualification for automotive applications. The hot-swap circuitry prevents inrush current and bus glitches during card insertion. The differential pair uses low-voltage signaling to reduce EMI compared to single-ended transmission. Typical applications include industrial I2C backplane extension, automotive sensor networks, hot-swappable I/O cards, multi-drop I2C sensor clusters, and remote sensor/PCI configuration. The device is particularly valuable where cables must span meters between cards, sensors, or backplane slots, and where live insertion is needed without disrupting the system bus. When designing with this part, ensure both VDD rails are decoupled with 100 nF ceramic capacitors placed within 5 mm of the supply pins. Verify the differential pair routing on the cable side is twisted-pair or shielded to meet EMI requirements; the part itself does not include cable termination resistors, so external 100 ohm differential termination may be required at the far end for very long runs.

RFQ پەیوەندی
PCA9616PW - 3-Channel Differential I2C Bus Buffer | NXP
PCA9616PW

PCA9616PW - 3-Channel Differential I2C Bus Buffer | NXP

The NXP Semiconductors PCA9616PW is a dual-supply, 3-channel multipoint Fast-mode Plus (Fm+) differential I2C-bus buffer with hot-swap logic, packaged in a 16-pin TSSOP (PW) surface-mount package. It buffers the single-ended SMBus/I2C-bus up to 1 MHz and converts it to a differential I2C (dI2C) bus that reliably extends communication through electrically noisy environments over cable runs of at least 3 meters, or longer at reduced clock speeds. A differential I2C-bus buffer, sometimes called a bus repeater or redriver, is an interface IC that belongs to the signal buffer family within the broader hierarchy of interface integrated circuits. Where a plain I2C bus uses open-drain single-ended lines vulnerable to ground bounce and common-mode noise, a dI2C buffer translates the bus into a differential current-mode signaling scheme, dramatically improving common-mode noise immunity while remaining fully compatible with existing Standard-mode, Fast-mode, and Fast-mode Plus I2C and SMBus devices. Key features of the PCA9616PW include its 3-channel multipoint architecture, which supports a dI2C bus shared by multiple nodes for multipoint topologies; its dual-supply design isolating the single-ended side from the differential side; support for Fast-mode Plus operation at 1 MHz; and integrated hot-swap logic that allows a card or module to be inserted into or removed from a live backplane without corrupting bus transactions. Signal direction is fully automatic, requiring no external direction-control signal. Technically, the device pairs each single-ended SDA and SCL line with differential transmit/receive pairs on the cable side, using current-mode differential drivers and receivers with high common-mode noise rejection. Because it is a multipoint buffer, several PCA9616 devices can share one differential cable, enabling distributed systems such as rack-mounted cards, industrial backplanes, and remote sensor clusters. NXP documents cable extension of at least 3 m, with longer runs achievable at lower bus speeds. Typical applications include industrial backplane I2C distribution, telecom and server shelf management, multipoint sensor networks in electrically noisy factory environments, and hot-pluggable module bus extension. The hot-swap logic makes it especially suitable for field-replaceable cards. Design consideration: plan the differential bus topology to respect multipoint stub-length limits, and verify supply sequencing on both the single-ended and differential rails against the manufacturer datasheet to guarantee correct hot-swap behavior. This page synthesizes distributor pricing, drop-in replacement analysis, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
PCA9617ADPJ - 1MHz Fm+ I2C Level Shifter | NXP | TSSOP-8
PCA9617ADPJ

PCA9617ADPJ - 1MHz Fm+ I2C Level Shifter | NXP | TSSOP-8

NXP Semiconductors PCA9617ADPJ is a bidirectional CMOS I2C-bus repeater and level-translating buffer supporting Fast-mode Plus operation up to 1 MHz, with a low-side voltage range of 0.8 V to 5.5 V, a high-side voltage range of 2.2 V to 5.5 V, and an 8-pin TSSOP package. The device is intended for I2C and SMBus systems that require voltage translation, bus isolation, or extension across voltage domains. A level-translating I2C buffer is an interface IC that allows two connected bus segments to operate at different logic voltages while preserving bidirectional clock and data communication. Its role within an interface hierarchy is a bidirectional bus repeater, followed by a level translator, followed by an interface IC. Bidirectional channels must actively reproduce the bus state in both directions so that pull-up resistors on each side can establish the correct local voltage. The PCA9617A supports low-side voltages from 0.8 V to 5.5 V and high-side voltages from 2.2 V to 5.5 V. Its 1 MHz operating capability makes it suitable for Fast-mode Plus I2C traffic, while the independent dual-supply arrangement allows a low-voltage controller to communicate with higher-voltage peripherals. The NXP product is also identified as a one-channel signal buffer or re-driver in distributor catalogs. The PCA9617A combines level translation with buffering. This allows a bus to remain usable when capacitance, voltage, or topology prevents direct connection between the two sections. Both I2C signal lines pass through the bidirectional repeater, and the enable control referenced to the high-side supply provides a way to place the drivers under system control. The enable state should only be changed while the bus is idle, preventing transitions on active clock or data lines. Typical applications include separating low-voltage sensors from 3.3 V or 5 V controllers, extending I2C runs across voltage domains, protecting a bus segment from another subsystem, and supporting mixed-voltage system partitioning. The device can also be used in industrial control, instrumentation, communications equipment, and compact embedded systems where a 1 MHz I2C interface crosses between domains with incompatible logic levels. The primary design consideration is correct pull-up placement. Each bus segment requires pull-up resistors referenced to its own supply voltage, and both sides should be configured for the voltages actually present in the design. The enable pin should be driven only while the I2C bus is idle. PCB layout should keep the two interface sections and their pull-up networks physically distinct to minimize coupling and maintain signal integrity. This page combines the electrical operating ranges, interface function, package information, comparison guidance, and practical implementation considerations needed to evaluate the PCA9617ADPJ as a drop-in bus-interface candidate.

RFQ پەیوەندی
PCA9618UKZ - Single-Channel Fm+ I2C Bus Repeater | NXP
PCA9618UKZ

PCA9618UKZ - Single-Channel Fm+ I2C Bus Repeater | NXP

NXP Semiconductors PCA9618UKZ is a single-channel CMOS repeater for Fast-mode Plus I2C-bus or SMBus signals, with a 4-WLCSP package measuring 0.83 mm by 0.78 mm. It can buffer either the SCL clock line or the SDA data line, and it also supports single-bit buffering applications. An I2C bus repeater is an interface IC that regenerates a digital communication signal between a bus controller and a downstream device. Repeaters extend usable bus distance, isolate capacitive loading, improve signal integrity, and allow separate bus segments to operate at compatible logic levels. In the broader semiconductor hierarchy, the PCA9618UKZ is a bus repeater, then an interface IC, then an integrated circuit and semiconductor. The principal benefit of the PCA9618UKZ is its combination of Fm+ I2C or SMBus compatibility, one-bit architecture, and compact WLCSP-4 footprint. The small package supports placement close to a connector, bus branch, or device interface. Its single-channel format also allows designers to add buffering where required rather than fitting a multi-channel device that would remain unused. The device is intended for separating clock and data paths when capacitive loading, bus extension, or signal-integrity constraints become important. In a typical implementation, the incoming side connects to the host or bus master, while the output side drives a downstream peripheral. The buffered path reduces the electrical loading seen by the source while maintaining the logic signaling required by I2C-compatible devices. Typical uses include sensor networks, industrial controllers, consumer equipment, communications modules, and compact embedded systems that use I2C or SMBus. The device is also suitable for generic single-bit level translation or buffering where the system requires regenerated logic rather than a multi-channel fixed-direction translator. Designers should place the repeater near the branch or load that requires isolation, verify timing margins at the intended bus rate, and account for package parasitics and board-level capacitance. The 4-WLCSP footprint also demands careful PCB layout, stencil and reflow control, and inspection because its ball pitch and dimensions leave little room for rework. This page consolidates the confirmed function, package information, sourcing details, interface considerations, and drop-in replacement status of the PCA9618UKZ. It also distinguishes verified device facts from electrical parameters that engineers must confirm in the NXP product specification before finalizing a design.

RFQ پەیوەندی
PCA9621D - 8-Bit 65mA I/O Expander | NXP | LED Drive
PCA9621D

PCA9621D - 8-Bit 65mA I/O Expander | NXP | LED Drive

The NXP Semiconductors PCA9621D is an 8-bit I/O expander with a 65 mA output sink capability, configurable from a 2-wire bus interface in a 16-pin SOIC package. It supports I2C-bus and SMBus control, while the manufacturer also describes compatibility with PMBus and similar serial-bus systems. An I/O expander is an interface IC that adds independently controlled digital outputs to a host processor. The PCA9621D belongs to the broader serial-interface controller hierarchy: it receives register writes over a 2-wire bus and converts those commands into eight configurable output-port states. This architecture reduces the number of GPIO pins required by a host and makes it useful when an embedded controller needs additional discrete output drive. The primary headline specifications are an 8-bit output port, 65 mA sink capability per device output, and operation from a 2-wire serial interface with support for I2C and SMBus. Its 16-SO package supports compact surface-mount PCB layouts. The output state is held in a programmable 8-bit register that the host can read and write through the serial interface. Each output can be treated as a general-purpose logic output rather than being limited to a conventional LED-driver function. The NXP product page specifically identifies the 65 mA sink capability as suitable for driving LEDs, while the general-purpose output architecture also supports relay, indicator, or logic-level signaling where the electrical limits are respected. The serial interface allows the host microcontroller to update output patterns without dedicating eight separate GPIO pins. Typical uses include status and indicator LED banks, alarm and warning lamps, industrial annunciation panels, lighting-control modules, and embedded systems with limited GPIO availability. A microcontroller or other 2-wire-bus controller writes the desired output pattern to the PCA9621D, and the device presents the corresponding states at its eight outputs. A device such as the PCA9621D can therefore consolidate repetitive indicator or lamp control into one serial interface. The principal design considerations are the absolute output current limit, the voltage levels accepted by the attached loads, and correct I2C or SMBus implementation. Each load path and output driver must remain within the device's stated 65 mA sink capability, while the PCB must provide adequate copper and thermal margin for the selected duty cycle. The manufacturer datasheet should be used for the complete pin description, electrical limits, timing information, and recommended application circuit. This page organizes the manufacturer specifications, purchasing information, application guidance, and pin-level design considerations for engineers evaluating the PCA9621D. It also provides a comparison framework for evaluating other 8-bit, 2-wire output-port devices against package, interface, output-current, and functional requirements.

RFQ پەیوەندی
PCA9641BSHP - 2-Channel I2C Master Arbiter | NXP
PCA9641BSHP

PCA9641BSHP - 2-Channel I2C Master Arbiter | NXP

The NXP PCA9641BSHP is a 2-channel I2C controller arbiter and 2-to-1 I2C demultiplexer designed for reliable systems in which two bus controllers can issue commands simultaneously. It selects a winning controller, allows that controller to operate without interruption, and gives the losing controller control of the I2C bus after the winner releases it. The device is supplied in a 16-pin HVQFN package with an exposed pad and tape-and-reel packaging. An I2C controller arbiter is an interface-management IC that coordinates access to a shared two-wire bus. It belongs to the hierarchy of I2C interface devices, serial bus controllers, bus arbiters, and interface ICs. Unlike a conventional I2C multiplexer, which routes one controller toward one of several downstream buses, the PCA9641 permits two controllers to share a common downstream bus while managing simultaneous access and arbitration timing. The PCA9641BSHP is intended for dual-controller architectures requiring deterministic bus ownership. Its central function is to select one master when both masters request the bus, allow the selected master to complete its transfer uninterrupted, and subsequently let the other master gain control. This behavior supports systems in which independent controllers, such as a processor and an auxiliary controller, must coexist on one I2C bus without placing both on the bus simultaneously. The 16-HVQFN construction supports compact PCB layouts while its exposed thermal pad provides a means for heat spreading and, where required, electrical connection to the ground reference specified by the manufacturer. Because the exposed-pad connection and layout requirements are package- and board-specific, PCB designers should follow the land pattern and thermal guidance in the NXP manufacturer datasheet rather than treating the pad as an unrestricted signal terminal. Typical uses include industrial control modules, embedded automation boards, dual-processor equipment, sensor systems, and communication equipment in which two embedded controllers must arbitrate access to one shared I2C segment. The arbiter role is particularly valuable when independent control loops or operating systems could otherwise generate overlapping bus activity. It is also suitable for bus-isolation architectures where downstream devices must not see simultaneous controller commands. Design consideration: arbitration timing, bus timeout behavior, pull-up placement, and controller compatibility determine whether the system remains reliable during simultaneous requests. Follow the NXP datasheet for master arbitration timing, reset behavior, electrical limits, and the recommended exposed-pad layout. Confirm that both connected controllers observe the intended bus ownership and release behavior before integrating the device into a safety- or uptime-critical system. This product page combines the verified NXP device description, package information, distributor records, technical application guidance, and a strict drop-in-replacement assessment. It distinguishes confirmed characteristics from parameters that require confirmation from the manufacturer datasheet, helping engineers evaluate the PCA9641BSHP without treating unverified electrical assumptions as design facts.

RFQ پەیوەندی
PCA9641PWJ - 2-Channel I2C Bus Arbiter | NXP
PCA9641PWJ

PCA9641PWJ - 2-Channel I2C Bus Arbiter | NXP

The NXP Semiconductors PCA9641PWJ is a 2-channel I2C bus controller arbiter and 2-to-1 master demultiplexer packaged in a 16-pin TSSOP. It is designed for dual-controller I2C systems in which two bus masters may issue commands simultaneously. The arbitration function selects one controller as the winner, allows that controller to operate without interruption, and enables the losing controller to take control when arbitration is required. An I2C controller arbiter is a specialized interface IC that manages competing requests to use a shared two-wire bus. The broader hierarchy is I2C controller arbiter, I2C bus interface, interface IC, semiconductor, and electronic component. Unlike a conventional I2C bus switch or channel multiplexer, the PCA9641 is specifically intended to arbitrate between two master controllers while also routing commands through a 2-to-1 master demultiplexer. The manufacturer identifies the PCA9641 as a 2-to-1 I2C master demultiplexer with an integrated arbiter function. Its principal role is high-reliability dual-master operation: the arbiter elects a winning master and prevents simultaneous masters from interfering with one another. The losing master can subsequently assume control of the shared I2C bus when the winning master releases it. This behavior is useful where deterministic bus ownership is needed more than simply routing separate I2C branches. Typical PCA9641PWJ applications include redundant or alternate industrial controllers, dual-processor instrumentation, embedded test equipment, controller isolation in complex electronics, and systems in which two embedded masters share access to the same peripheral bus. The device helps centralize command arbitration close to the I2C domain, reducing the need for firmware-level coordination during simultaneous access attempts. The PCA9641PWJ is identified by NXP as a 16-TSSOP device, and distributor listings classify it as a two-channel buffer and multiplexer. Because arbitration behavior depends on the complete circuit, designers should follow the manufacturer datasheet for pin assignments, electrical limits, operating conditions, timing, and recommended application wiring rather than relying on generic I2C-switch schematics. For PCB implementation, place the device close to the controlled I2C segment, route clock and data traces as a matched pair, and keep the arbitration inputs, master request signals, and bus connections away from noisy switching stages. The 16-pin TSSOP footprint supports compact designs, but power, ground, and signal-integrity requirements should be checked against the latest NXP documentation before layout release. This page organizes the exact product identity, manufacturer documentation, package information, application context, and verified replacement information for PCA9641PWJ. It also distinguishes true drop-in candidates from parts that are only functionally similar, helping engineers assess PCB reuse without assuming that equivalent bus-routing functions guarantee identical pin compatibility.

RFQ پەیوەندی
PCA9646D - 4-Channel 1 MHz I2C Bus Buffer | NXP
PCA9646D

PCA9646D - 4-Channel 1 MHz I2C Bus Buffer | NXP

The NXP Semiconductors PCA9646D is a buffered four-channel 2-wire bus switch operating up to 1 MHz in a 16-pin SOIC package. Each of its four outputs can be enabled independently through the programmable control register, allowing unused branches to remain isolated. The monolithic CMOS device supports I2C-bus, SMBus, PMBus, and compatible two-wire systems, with electrical isolation between all five branches. A buffered 2-wire bus switch is an interface IC that regenerates bus signals while separating capacitive loads into independently controlled branches. In the hierarchy of semiconductor components, it belongs to the bus switch and interface-switch class, within logic and interface ICs. This differs from a basic multiplexer because the buffered outputs are designed to drive larger bus capacitance and maintain signal quality as branches are added. The PCA9646D provides four independently enabled output channels, a maximum operating frequency of 1 MHz, and support for five branches when the input bus is included. The NXP datasheet states that the device can support up to five 400 pF loads for Fm+ I2C-bus operation at 1 MHz. At lower operating frequencies, the stated capability extends to five 4 nF loads. Every I/O is impedance-isolated from the others, helping prevent inactive branches from degrading signal integrity. Control is performed through a programmable register, allowing any combination of the four outputs to be enabled. Multiple PCA9646 devices may also be cascaded when a system needs more segmented branches. This architecture is useful where bus capacitance, propagation delay, or branch loading would make a direct multi-device connection impractical. The device is designed for industrial-temperature operation from -40°C to +85°C and is supplied in a surface-mount 16-pin SOIC package. Typical uses include isolating sensors on an I2C bus, connecting LED controllers to PMBus-compatible systems, partitioning SMBus devices, and supporting multi-branch industrial control boards. The four independently controlled outputs are especially useful when several devices share the same bus address or when a branch must be disconnected to prevent leakage from an inactive peripheral. PCB design should preserve short, symmetric routing between the upstream bus and each output branch, while keeping ground returns continuous. The input and output nets must observe the capacitance limits stated in the manufacturer datasheet because longer branches or excessive loading can reduce rise time and cause communication errors even when the nominal clock is below 1 MHz. This page consolidates the device architecture, operating limits, branch-loading capabilities, lifecycle information, and application guidance into a practical engineering reference for I2C-bus and SMBus buffer design.

RFQ پەیوەندی
PCA9661B - 3.3V I2C Bus Controller | NXP | LQFP-48
PCA9661B

PCA9661B - 3.3V I2C Bus Controller | NXP | LQFP-48

The NXP Semiconductors PCA9661B is a 3.3 V I2C parallel-interface bus controller designed for data-intensive I2C transfers. It is offered in a 48-LQFP package measuring 7 mm by 7 mm and operates across the -40°C to 85°C temperature range. The device provides one I2C-bus channel and uses parallel interface logic to connect a host-side parallel bus with external serial peripherals. An I2C-bus controller is an interface IC that manages transactions between a parallel processor or bus master and devices connected through the two-wire I2C interface. In the broader semiconductor hierarchy, the PCA9661B belongs to the I2C controller class, which falls under interface controllers and then general-purpose interface ICs. Its role is to translate parallel data, control signaling, and bus timing into serialized I2C transfers for displays, sensors, memory devices, communications modules, and other peripheral ICs. NXP describes the PCA9661 as an advanced, fourth-generation, single-leader-mode bus controller. The B revision is identified in the product information as a single-master or single-leader I2C controller. Its architecture is intended to support dense systems where a processor-side parallel interface must service multiple I2C destinations efficiently. Parallel-to-serial bus management can reduce repetitive software transactions by centralizing addressing, control, and status handling in dedicated hardware. The 3.3 V operating supply matches many contemporary embedded processors, application processors, programmable logic devices, and communication controllers. This makes the PCA9661B useful in industrial controllers, test equipment, embedded computing platforms, communications infrastructure, and data-acquisition systems that already operate from a 3.3 V rail. Designers should confirm signal levels, timing limits, supported operating modes, and exact register behavior against the manufacturer datasheet before finalizing a new design. The 48-LQFP package exposes 48 leads, but its 1.4 mm package height does not by itself determine minimum PCB pad geometry. Follow the NXP land-pattern and stencil recommendations, including exposed-pad and soldering details shown for the selected orderable variant. Account for signal propagation between the parallel interface and the I2C pins, and place pull-up and bus-capacitance components where they can maintain a short return path. NXP marks the PCA9661B as not recommended for new designs and identifies PCA9665APW as its recommended replacement. Existing installations may continue to use the PCA9661B for maintenance or design continuity, but new products should evaluate the recommended NXP successor and confirm whether its package, pinout, registers, voltage limits, timing, and thermal characteristics permit a direct PCB substitution. The PCA9665APW is not represented here as a drop-in alternative because the available product information does not establish pin-to-pin and package equivalence. This page organizes the verified product identity, lifecycle guidance, electrical limits, package details, design considerations, replacement analysis, and application guidance. It distinguishes confirmed manufacturer information from parameters that still require direct review of the datasheet, helping engineers separate verified device facts from assumptions before schematic capture, PCB layout, or production sourcing.

RFQ پەیوەندی
PCA9663B - 3-Channel Fm+ I2C Controller | NXP | LQFP-48
PCA9663B

PCA9663B - 3-Channel Fm+ I2C Controller | NXP | LQFP-48

NXP PCA9663B is a parallel-bus to three-channel I2C-bus controller supporting data rates up to 1 Mbit/s through Fast-mode Plus open-drain channels, packaged in a 48-LQFP 7 x 7 mm package. The device operates from a 3.3 V supply, includes three independent I2C channels, and provides a 4352-byte data buffer per channel for data-intensive serial transfers. An I2C-bus controller is an interface IC that converts parallel host-bus transactions into serial I2C commands and manages the timing, addressing, and data transfer protocol. The PCA9663B belongs to the parallel-bus-to-I2C-controller segment of the interface IC hierarchy, where it connects a conventional microprocessor or host bus with multiple I2C peripherals. Its three-channel architecture allows separate serial buses to operate independently rather than sharing one serialized channel. Key features include Fast-mode Plus operation, 1 Mbit/s maximum data rate, 30 mA SCL and SDA sink-current capability, and an internal oscillator trimmed to 1% accuracy. The generous 4352-byte buffer on each channel reduces host-service overhead during sustained transfers. These characteristics make the controller useful when a system must move blocks of sensor, display, communications, or configuration data over I2C without tying up the host on every byte. The PCA9663B is designed for data-intensive parallel-to-serial conversion. Each channel uses the standard open-drain Fm+ topology, allowing the bus lines to be pulled up externally as required by the system voltage and capacitance. The internal trimmed oscillator removes the need for an external precision timing component, while independent channel state supports simultaneous work on multiple bus domains. Configuration registers and command handling are managed through the parallel host interface. Typical applications include industrial sensor aggregation, programmable logic or microcontroller peripheral expansion, multi-channel display or control systems, telecommunications equipment, and embedded data-acquisition platforms. Three independent channels can support groups of sensors, memory devices, or transceivers while isolating their traffic. The 1 Mbit/s rate is appropriate for high-volume configuration and monitoring data without moving control traffic to a much faster parallel or serial interface. PCB design should preserve short, clean SCL and SDA routing, provide the required pull-up resistors, and place decoupling capacitors close to the supply pins. Because the external pull-up value affects rise time and bus timing, it should be selected from the actual board capacitance and the Fm+ requirements. Review the manufacturer's pin and connection guidance before assigning host-bus signals or laying out the three I2C channels. This product page combines the manufacturer's core electrical and architecture information with package details, sourcing workflows, selection guidance, and practical implementation considerations. It is designed to help engineers determine whether the PCA9663B matches the required channel count, transfer rate, buffering, voltage, and LQFP-48 footprint before beginning PCB design.

RFQ پەیوەندی
PCA9665D - Fm+ Parallel to I2C Controller | NXP | 20-SO
PCA9665D

PCA9665D - Fm+ Parallel to I2C Controller | NXP | 20-SO

The NXP PCA9665D is an Fm+ parallel-bus to I2C-bus controller packaged in a 20-pin SOIC. It is designed for systems in which a parallel processor or programmable logic device must communicate with I2C peripherals. The controller provides a structured bridge between a parallel host interface and the serial I2C bus, reducing the firmware and wiring burden associated with bit-level I2C transactions. Its nominal supply range is 2.5 V to 3.3 V, and the device consumes approximately 100 uA of supply current. An I2C bus controller is an interface IC that converts commands and data from a parallel or processor-specific bus into transactions on an I2C serial bus. The I2C interface uses SDA for bidirectional data and SCL for the clock, while the parallel side communicates with a host using a dedicated address and data register arrangement. This device family is useful when a controller, display subsystem, communications equipment, or embedded logic platform needs to access low-speed I2C peripherals without using an I2C-capable host controller. The PCA9665D is identified by NXP as an Fm+ parallel bus to I2C-bus controller. Its 20-pin SOIC package supports conventional surface-mount assembly and provides a practical upgrade path for designs that require a dedicated parallel-to-I2C bridge. The 2.5 V to 3.3 V operating range is compatible with low-voltage digital systems, while the approximately 100 uA supply current is important in equipment where the interface must not create an unnecessary standing load. Detailed clock, addressing, electrical, and timing limits should be taken from the manufacturer datasheet. Typical uses include industrial control panels, programmable-logic-based peripherals, test systems, communication modules, display-control boards, and embedded equipment that exposes an I2C bus through a parallel host interface. The PCA9665D is especially useful when the existing host processor does not provide a suitable I2C peripheral. In such designs, the parallel interface can be connected to external logic or a processor bus, while the I2C side reaches sensors, EEPROMs, expanders, and other compatible devices. When laying out a replacement design, verify the exact package variant, supply voltage, address behavior, clock timing, and signal levels against the NXP datasheet before production release. The D suffix denotes the 20-pin SO option, while other NXP order codes may use different package or shipping arrangements. Check the mechanical drawing and pin table for the selected ordering code rather than assuming every PCA9665-family order code has the same footprint.

RFQ پەیوەندی
PCA9665N - 1MHz FM+ Parallel-to-I2C Controller | NXP
PCA9665N

PCA9665N - 1MHz FM+ Parallel-to-I2C Controller | NXP

The NXP Semiconductors PCA9665N is a Fast-mode Plus parallel-bus to I2C-bus controller that supports data rates up to 1 MHz, provides a 68-byte data buffer, and offers 25 mA SCL/SDA drive capability. It is offered in a 20-pin through-hole DIP package for industrial applications. The device can operate as either an I2C master or slave and transfers data between a parallel microcontroller or microprocessor and a serial I2C bus. An I2C controller is an interface IC that bridges parallel processor buses and the serial I2C ecosystem. Parallel buses transfer multiple bits simultaneously, while I2C uses clocked SDA and SCL lines to exchange data between integrated circuits. The PCA9665N places this conversion in a dedicated peripheral, reducing the number of serial transactions and GPIO connections required by a host processor when it must control multiple I2C devices. The PCA9665N supports I2C Fast-mode Plus operation at 1 MHz and can drive SCL and SDA lines with 25 mA capability. Its 68-byte buffer supports byte-oriented and buffered data transfers between the parallel and serial sides. General Call support and software reset over the parallel bus add useful control functions for systems that need coordinated peripheral addressing or restart behavior. Two operating modes make the controller suitable for different system architectures. In master mode, it initiates transfers on the I2C bus; in slave mode, it responds to another bus controller. Communication can be interrupt-driven or managed through a polled handshake, allowing the interface to fit both event-driven firmware and simpler supervisory control loops. Typical applications include industrial control equipment, test and measurement systems, communication modules, peripheral expansion, legacy parallel-processor systems, and embedded products that need to retain a parallel bus while adding modern serial peripherals. Its through-hole DIP format is particularly useful for prototypes, legacy control boards, and industrial systems assembled around through-hole components. Designers should account for the 1 MHz bus limit, confirm that every connected I2C device supports the intended speed, and validate pull-up resistor sizing for the target bus voltage and capacitance. Because Fast-mode Plus uses lower resistance pull-ups than standard Fast-mode, incorrect resistor values can produce excessive rise times, ringing, or communication errors. This page organizes the manufacturer-described controller capabilities, package information, sourcing pathways, and engineering trade-offs into a concise selection guide. It also distinguishes the DIP-20 target from similarly named PCA9665 devices offered in SOIC, TSSOP, and HVQFN packages, which cannot replace this through-hole part without a PCB redesign.

RFQ پەیوەندی
PCA9670BS,118 - 8-bit Fm+ I2C I/O Expander w/ Reset, HVQFN-16
PCA9670BS,118

PCA9670BS,118 - 8-bit Fm+ I2C I/O Expander w/ Reset, HVQFN-16

The NXP PCA9670BS,118 is a remote 8-bit I/O expander for Fast-mode Plus (Fm+) I2C-bus with reset, packaged in a 16-pin HVQFN (3x3 mm) with exposed thermal pad. The device provides general-purpose remote I/O expansion for most microcontroller families via the two-line bidirectional I2C-bus, and supports a clock frequency of up to 1 MHz. Operating supply range is 2.3 V to 5.5 V, allowing use with 3.3 V and 5 V logic rails. The integrated RESET input and quasi-bidirectional I/O structure simplify firmware and PCB design when adding buttons, LEDs, keypads, or sensor interfaces to an embedded system. An I/O expander (also called a port expander or GPIO expander) is a category of interface IC that multiplies the limited GPIO pins of a microcontroller through a serial bus. In the taxonomy I/O expander -> interface IC -> integrated circuit -> semiconductor, the PCA9670BS sits in the parallel-bus-expansion tier and uses I2C as the transport. By attaching the part to SCL/SDA, designers gain eight additional quasi-bidirectional I/O pins addressed through a 7-bit slave address. Three hardware address pins (A0, A1, A2) allow up to 64 PCA9670 devices on the same bus, supporting up to 512 I/Os (for example 512 LEDs) without external bus buffers. Key features include 1 MHz Fm+ bus support (compared with 400 kHz for the classic PCF8574), a hardware RESET pin that reverts all ports to inputs, low standby current, and 5 V tolerant I/O structure that tolerates bus pulls above VDD. The HVQFN-16 (3x3) package provides a low 0.5 mm profile with an exposed die attach paddle for improved thermal performance, making it suitable for compact industrial, consumer, and IoT designs. NXP specifies ESD protection exceeding 2 kV HBM on the I/O pins, and the part is qualified to the industrial -40 C to +85 C operating range. The PCA9670 architecture uses an I2C state machine with interrupt logic for input-change notifications and a separate RESET input that asynchronously clears internal state. Internally each I/O pin is a quasi-bidirectional structure - capable of sinking current to drive LEDs directly while also serving as an input when written high. This dual-mode behavior differs from push-pull GPIO and is important when migrating designs from the older PCF8574/PCF8575 family. Typical applications include keypad and button-matrix scanning in white goods and access control, LED driving and chase patterns in industrial control panels, sensor multiplexing on Raspberry-Pi-class SBCs where the host lacks enough native GPIO, and general-purpose I/O expansion in PLC and HVAC controllers. The wide 2.3-5.5 V supply range plus 1 MHz Fm+ bus speed also suits battery-powered IoT nodes that need to minimize I2C transaction time. When designing with this part, place 100 nF decoupling close to VDD, use external pull-ups on SDA/SCL sized for the bus capacitance (typically 4.7 kohm at 1 MHz), and avoid leaving the RESET pin floating - tie it to VDD through a 10 kohm resistor or drive it from the host MCU. The I/O sink capability must be checked against LED forward current; sourcing current is limited and the quasi-bidirectional behavior must be considered when interfacing to logic-level peripherals. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the NXP datasheet.

RFQ پەیوەندی
PCA9671D - 16-Bit I2C FM+ I/O Expander | NXP
PCA9671D

PCA9671D - 16-Bit I2C FM+ I/O Expander | NXP

The NXP Semiconductors PCA9671D is a 16-bit remote I/O expander for I2C buses operating up to 1 MHz, with reset support and 16 general-purpose output ports. It is supplied in a 24-pin SO package designated 24-SO. The device adds 16 remotely controlled digital output lines to a host microcontroller while using only the two-wire I2C interface for communication. An I/O expander is an interface IC that extends the number of controllable input or output lines available from a host processor. The PCA9671D belongs to the I/O expander hierarchy within interface ICs and semiconductor devices. Its Fast-mode Plus capability allows a higher bus rate than conventional 400 kHz I2C operation, making it suitable for systems that need flexible logic-control functions without dedicating numerous host-controller pins. The main features include 16 output ports, 1 MHz I2C operation, a reset input, and configurable pull-up behavior represented by the PU designation. The reset function provides a defined way to restore the device state during system initialization or fault recovery. Each output can serve as a general-purpose logic signal, while bus-driven functions can extend the device beyond simple static GPIO control. The PCA9671D is designed for use with microcontrollers and other embedded processors that lack sufficient direct I/O pins. Its 24-pin SO package supports compact PCB layouts while keeping the I2C connection simple. Because an I/O expander adds bus-controlled peripheral functions around the processor, designers should account for bus timing, address allocation, pull-up resistors, output load limits, and reset timing in the system architecture. Typical uses include LED status and indicator arrays, relay-control interfaces, reset or enable signaling for external circuits, industrial control modules, communication equipment, and embedded systems with several discrete logic outputs. The 1 MHz bus rate can reduce communication delay when many outputs are updated, while the 16-bit output count consolidates control traffic into a compact serial interface. Layout should place pull-up components and decoupling close to the relevant device pins, and the I2C routing should preserve signal integrity. Firmware must assign a unique address, configure the intended output states, and account for the reset state before enabling external loads. The manufacturer datasheet is the controlling reference for absolute maximum ratings, electrical limits, pin functions, and recommended operating conditions. This product page consolidates the confirmed interface, package, and ordering information with practical design guidance for I2C layout, reset implementation, firmware configuration, and system expansion. It is intended to help engineers determine whether the PCA9671D can satisfy a remote-output requirement while avoiding unnecessary host-controller pin allocation.

RFQ پەیوەندی
PCA9672D - 8-Bit I/O Expander with 1 MHz I2C | NXP
PCA9672D

PCA9672D - 8-Bit I/O Expander with 1 MHz I2C | NXP

NXP Semiconductors PCA9672D is an 8-bit remote I/O expander with a 1 MHz I2C Fast-mode Plus interface, operating from 2.3 V to 5.5 V. The device provides eight quasi-bidirectional GPIO ports, three hardware address inputs, an interrupt output, and a reset input in a 16-pin SO package. An I/O expander is an interface IC that adds parallel digital input or output capability to a host controller over a serial bus. In the product hierarchy, the PCA9672D is an I/O expander within interface ICs and semiconductors. Its two-wire I2C connection reduces the number of host-controller pins required when a design needs additional control, status, or general-purpose I/O lines. The principal features include eight quasi-bidirectional ports, I2C Fast-mode Plus operation up to 1 MHz, three hardware address inputs, an interrupt output, and a reset input. The 2.3 V to 5.5 V operating range permits use in both 3.3 V and 5 V systems. Quasi-bidirectional ports can be configured individually as inputs or outputs, allowing the same external connector or control interface to combine input and output signals. The PCA9672D supports both interrupt-driven and polling-based host communication. An output port can generate an interrupt when a connected input changes state, allowing the host to handle events without continuously polling all eight inputs. The reset input provides a defined recovery path for the serial interface and port state. I2C address selection through three hardware address inputs permits multiple expanders on the same bus when their address straps are assigned differently. Typical uses include LED status and control panels, keypad and switch interfaces, industrial automation modules, sensor gathering, alarm and monitoring equipment, and compact embedded control boards. The 1 MHz bus rate is particularly useful for LED dimming or moderate-rate control traffic, while the interrupt output improves responsiveness in event-driven systems. Designers should verify the electrical characteristics of each quasi-bidirectional port, including its output-current capability and pull-up arrangement, before driving loads. The PCB layout should keep the I2C traces short, provide continuous ground references, and place bypass and pull-up components close to their associated pins. Firmware must also define startup states to avoid unintended outputs during reset. This product page combines the manufacturer feature summary, package identification, lifecycle information, ordering-code details, and practical guidance for I2C expansion, event handling, reset behavior, and PCB implementation. It also distinguishes exact ordering variants from unrelated interface ICs that use similar functions but do not share the same package and pin arrangement.

RFQ پەیوەندی
PCA9673D - 16-Bit I2C GPIO Expander | NXP Semiconductors
PCA9673D

PCA9673D - 16-Bit I2C GPIO Expander | NXP Semiconductors

The NXP Semiconductors PCA9673D is a remote 16-bit I/O expander for Fast-mode Plus I2C communication, operating at a maximum clock frequency of 1 MHz across a 2.3 V to 5.5 V supply range. The device is offered in a 24-pin SOIC package and provides interrupt and reset functions for connected microcontroller systems. An I/O expander is a peripheral interface IC that increases the number of general-purpose input or output lines available to a host processor. It sits within the embedded-control hierarchy as an I2C peripheral, allowing a microcontroller or application processor to control or monitor external signals over the two-wire bus instead of requiring one host GPIO for every external line. The PCA9673D therefore belongs to the interface IC family rather than the microcontroller or GPIO-controller families. Its principal features include 16 remotely controlled I/O lines, a 1 MHz I2C clock rate, compatibility with Fast-mode Plus operation, and dedicated interrupt and reset functions. The 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V system environments when the host, pull-up network, and external loads are designed for the corresponding voltage. The 24-pin SOIC format supports conventional surface-mount assembly and PCB routing. The PCA9673D is intended for systems in which a controller needs additional digital interface points. I2C address control, register-based configuration, and the interrupt output can reduce direct host-controller pin usage while providing a structured way to monitor external events. Because bus capacitance, pull-up resistance, voltage levels, and output timing influence reliable operation, the device should be used with a power supply and I2C network that remain within the manufacturer's stated limits. Typical uses include industrial control modules, sensor-hub boards, programmable logic controllers, test equipment, and compact embedded products that need more digital lines than the host controller provides. Its interrupt function is especially useful when an external change must wake or notify the host, while the reset function supports coordinated initialization of the expansion interface and attached circuitry. PCB layout should keep the I2C wiring short and route the SCL and SDA nets away from high-current switching edges. Confirm pull-up values for the intended bus voltage and frequency, provide suitable decoupling at the supply pins, and review the 24-pin pin-description table in the manufacturer datasheet before assigning every signal. The package drawing and pin names should be checked against the selected assembly footprint. This page consolidates the verified device specifications, ordering information, package details, replacement constraints, and practical implementation guidance into a design-oriented resource. It also distinguishes the documented PCA9673D configuration from order-code variants and explains which compatibility claims must be confirmed at the pin, voltage, and timing level before substitution.

RFQ پەیوەندی
PCA9674D - 8-Bit 1MHz I/O Expander | NXP Semiconductors
PCA9674D

PCA9674D - 8-Bit 1MHz I/O Expander | NXP Semiconductors

The NXP Semiconductors PCA9674D is an 8-bit remote I/O expander with a 1 MHz I2C Fast-mode Plus interface, eight quasi-bidirectional GPIO ports, and an interrupt output, supplied in a 16-pin SOIC package. Its operating supply range is 2.3 V to 5.5 V, making it suitable for low-voltage embedded systems and conventional 5 V industrial interfaces. An I/O expander is an interface IC that adds digital input and output ports through a serial bus. In the product hierarchy, the PCA9674D is an I/O expander within the interface IC category and a peripheral for microcontrollers and other I2C hosts. The host controller uses SCL and SDA to configure the ports, read inputs, change output states, and receive an interrupt when an input condition is detected. The PCA9674D provides eight quasi-bidirectional ports, a 1 MHz I2C bus, three hardware-selectable address inputs, and an interrupt output. Its eight ports can be individually configured as inputs or outputs through the device registers. Quasi-bidirectional ports include an internal pull-up arrangement and can support LED dimming through PWM-compatible output control. The I2C interface also allows multiple expanders to share one bus through address selection. The device supports up to 64 hardware-selectable addresses because A0, A1, and A2 provide three binary address inputs. This enables a bus to connect many remote I/O ports without requiring a separate microcontroller pin for each device. The PCA9674D and PCA9674A use non-overlapping slave-address ranges, allowing both families to operate together on the same I2C bus for further expansion. Typical uses include reading switches and push buttons, driving LEDs, controlling solenoid or relay interfaces, monitoring digital sensors, and adding GPIO capacity to industrial controllers. The 1 MHz bus rate also makes the device suitable for LED backlight control and other applications where the host must update multiple output states efficiently. PCB design should place the I2C pull-up resistors and bypass capacitor close to the appropriate supply and bus pins. Account for address selection before fixing the PCB, because the A0, A1, and A2 levels determine the slave address. Confirm that downstream devices remain compatible with the quasi-bidirectional port behavior before using an output pin as a strong source for a high-current load. This product page consolidates the electrical limits, package details, lifecycle information, pin assignments, sourcing guidance, and verified drop-in alternatives into one engineering reference. It also highlights the boundary between a true pin-compatible replacement and a functionally similar GPIO expander that requires a different footprint or interface arrangement.

RFQ پەیوەندی
PCA9674N - 8-Bit 1MHz I2C I/O Expander | NXP
PCA9674N

PCA9674N - 8-Bit 1MHz I2C I/O Expander | NXP

The NXP Semiconductors PCA9674N is an 8-bit remote I/O expander with a 1 MHz Fast-mode Plus I2C-bus interface, operating from 2.3 V to 5.5 V and housed in a 16-pin DIP package. It adds eight independently controlled GPIO outputs to a host microcontroller while providing an interrupt output for change notification. An I/O expander is an interface IC that extends the number of digital input or output pins available to a microcontroller or other bus controller. The PCA9674 belongs to the broader hierarchy of I2C interface ICs, parallel-port expanders, GPIO controllers, and power-management system semiconductors. It is useful when the host device has insufficient direct GPIO pins or when remote peripherals need to share a two-wire control bus. Three address-select inputs allow the PCA9674 to be assigned among 64 addresses, supporting up to 126 PCA9674 and PCA9674A devices on one I2C-bus without bus buffers and as many as 1,008 controlled I/Os. Its 1 MHz bus speed exceeds the 100 kHz Standard-mode rate, while the 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V systems. The interrupt output enables a host to respond to port events without continuously polling all eight outputs. The device separates serial bus control from parallel output handling. The host writes to the PCA9674 registers over I2C and receives an interrupt when a configured output state changes. Its 8-bit organization and hardware-selectable address pins make multiple expanders practical in LED panels, control boards, and distributed peripheral interfaces. The through-hole 16-DIP format is also convenient for prototyping and through-hole industrial assemblies. Typical uses include LED status indicators, relay or contactor control, display and keypad interfaces, industrial control modules, and general-purpose board I/O expansion. The PCA9674 is particularly suitable when a microcontroller must monitor remote logic states while preserving limited pins for communications, timing, or analog functions. For reliable implementation, connect pull-up resistors to the SDA and SCL lines, route the bus away from noisy switching nodes, and treat the address pins as board-level configuration. Verify the 2.3 V to 5.5 V operating range against the voltage applied to VDD and the logic levels used by the connected host. This page consolidates the NXP device specifications, address architecture, package information, selection guidance, and practical integration notes. It also identifies the closest same-footprint alternatives while clearly distinguishing confirmed orderable variants from functionally similar devices that require additional design review.

RFQ پەیوەندی
PCA9675D - 16-Bit I/O Expander, 1 MHz | NXP
PCA9675D

PCA9675D - 16-Bit I/O Expander, 1 MHz | NXP

The NXP Semiconductors PCA9675D is a remote 16-bit I/O expander for I2C buses, supporting clock speeds up to 1 MHz in a 24-pin SOIC package. It provides a Fast-mode Plus compatible interface, interrupt support, and general-purpose output expansion for microcontroller-based systems. The device is positioned as a drop-in upgrade for the PCF8575 while increasing I2C-bus speed from 400 kHz to 1 MHz and supporting PWM LED dimming. An I/O expander is an interface IC that increases the number of general-purpose input or output lines available to a host microcontroller. By connecting these additional lines over a two-wire I2C bus, the PCA9675D reduces the pin count required on processors with limited direct I/O. It sits within the interface-IC hierarchy and connects a microcontroller to external indicator, lighting, switch, and control circuits without requiring a large number of host GPIO pins. The principal features of the PCA9675D include 16 remotely controlled I/O lines, operation from a 2.3 V to 5.5 V supply range, and I2C communication up to 1 MHz. Its Fast-mode Plus capability is significant when the expanded outputs are used for LED PWM dimming because the system can update a larger number of outputs more rapidly than a conventional 400 kHz I2C implementation. The interrupt output provides a mechanism for notifying the host when a monitored input changes. The PCA9675D is intended to work with most microcontroller families that support a compatible I2C interface. Its 24-pin SOIC package, 1 MHz bus capability, and 16-bit expansion make it suitable for applications where a conventional PCF8575-class expander would impose a lower 400 kHz bus limit. The device also supports both 30 mA I2C-bus drive and higher-bus-speed operation compared with the referenced PCF8575 architecture. Typical applications include LED signs and displays, server and networking equipment, industrial control systems, PLC peripheral interfaces, cellular telephone equipment, gaming machines, and instrumentation or test equipment. In an LED dimming design, the host writes output states and PWM information over I2C, while the expander handles the timing and level conversion required by multiple external LED channels. PCB design should preserve short I2C routing, minimize branch-stub length, and provide suitable pull-ups on SCL and SDA. Decoupling close to the supply pins is important for dependable operation in systems containing switching converters. Because the PCA9675D can source or sink substantial I2C current, bus capacitance, pull-up resistance, voltage level, and simultaneous operating current should be checked against the device limits before production release. This page combines the manufacturer's product information, package and interface characteristics, replacement guidance, comparison parameters, and practical implementation considerations. It also identifies the important distinction between a genuine SOIC-24 drop-in alternative and options that require a different footprint, allowing engineers to make a board-level replacement decision without relying on generic cross-reference results.

RFQ پەیوەندی
PCA9675PW,118 - 16-bit Fm+ I2C I/O Expander | NXP | TSSOP-24
PCA9675PW,118

PCA9675PW,118 - 16-bit Fm+ I2C I/O Expander | NXP | TSSOP-24

The NXP PCA9675PW,118 is a 16-bit remote I/O expander for the Fast-mode Plus (Fm+) I²C-bus, supplied in a 24-pin TSSOP (PW) package and shipped on 13-inch tape and reel. It operates from a supply voltage of 2.3 V to 5.5 V, clocks the I²C interface at up to 1 MHz, and exposes 16 quasi-bidirectional I/O lines that can source/sink up to 30 mA per pin with a 100 mA total package limit. An I/O expander (also called a port expander or GPIO expander) is a category of interface IC that increases the number of general-purpose I/O pins available to a host microcontroller over a serial bus such as I²C. In the system hierarchy it sits between the MCU and the discrete digital loads (LEDs, keypads, sensors, relay coils), translating compact I²C transactions into parallel pin-level updates. The PCA9675 belongs to NXP's Fm+ family, which is optimized for high-speed serial I/O expansion in noisy or long-trace industrial backplanes. Key features include three hardware address pins (A0/A1/A2) supporting up to eight PCA9675 devices on the same bus, an active-low interrupt output (INT) that asserts when any input changes and releases on the next I²C read, an active-low reset input with internal power-on reset, and per-pin latch-up current exceeding the 100 mA JESD78 limit. The device is a drop-in upgrade for the legacy PCF8575, lifting bus speed from 400 kHz to 1 MHz and raising sink current capability. Typical applications include PWM dimming of LED arrays (each pin can be modulated at >1 MHz bus rates), keypad and switch-matrix scanning, fan-speed and relay control in industrial PLCs, and general-purpose I/O expansion for low-pin-count MCUs in white goods, HVAC, and IoT edge nodes. Designers value the wide 2.3–5.5 V supply range because it allows direct interface to both 3.3 V and 5 V microcontrollers without level shifters. When designing with this device, place 100 nF decoupling on VDD as close as possible to the pin and pull SDA/SCL high with 4.7 kΩ resistors for standard 400 kHz operation or 1 kΩ for the full 1 MHz Fm+ rate. Note that quasi-bidirectional outputs require no external pull-up on the load side because an internal weak pull-up is enabled after each read cycle.

RFQ پەیوەندی