Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
SI3215-BT - Programmable SLIC/Codec | Silicon Labs
The Silicon Labs SI3215-BT is a single-channel programmable CMOS Subscriber Line Interface Circuit and integrated codec with ringing and battery-voltage generation, packaged in a 38-pin TSSOP. It supports a 3.13 V to 5.25 V supply range, 41 mA operating current, 60 dB signal performance, and GCI, PCM, and SPI interfaces. Its software-configurable ringing generator supports up to 5 REN and 90 VPK. A SLIC is the analog-facing circuit that connects a telephone line to a digital voice system, while a codec converts between analog voice signals and digital PCM data. The SI3215-BT combines these functions into one programmable device, placing line termination, voice conversion, ringing generation, and battery feeding in a single telecom interface IC. Programmable internal balanced ringing is one of the device’s principal functions. The ringing engine can operate at 5 REN up to 4 kft or 3 REN up to 8 kft, with a maximum ringing voltage of 90 VPK. DTMF generation, BORSCHT line functions, and expanded support for Japan and China country requirements broaden its applicability to regional analog telephone systems. An integrated battery supply and dynamically controlled DC-DC converter produce the negative battery voltage required by the line interface. The converter continuously adjusts its operating point to minimize power consumption. According to the manufacturer datasheet, the SI3215 also performs all BORSCHT functions and supports software migration considerations from the earlier Si3210 family. Typical uses include single-line VoIP adapters, analog terminal adapters, embedded telephony gateways, voice-over-IP endpoint equipment, and legacy telephone interface designs that require PCM or GCI connectivity. The 38-pin TSSOP package is suitable for conventional surface-mount assembly where the system also requires high-voltage ringing and battery circuitry. Designers must account for the line-side high voltage, isolated ringing requirements, analog impedance matching, digital codec timing, and power-supply sequencing. The exact hook state, DC feed, ringer threshold, and country-specific parameters should be programmed and validated against the target line and network requirements before production release. This product page combines package, interface, ringing, supply, and application details with practical design considerations for engineers evaluating the SI3215-BT. It also identifies the limitations of cross-reference results so that a replacement is selected only when package, pinout, interface, and telephone-network behavior are confirmed together.
SI3215-C-FM - ProSLIC SLIC/Codec with 90VPK Ringing | Skyworks
The Skyworks SI3215-C-FM is a single-channel ProSLIC Subscriber Line Interface Concept (SLIC) and CODEC IC housed in a 38-pin QFN (5x7 mm) package, integrating software-configurable 5 REN internal ringing up to 90 VPK, DTMF generation, and a comprehensive set of telephony signaling capabilities with expanded support for Japan and China country requirements. It pairs with the Si3201 line-side DC-DC controller (in a thermally-enhanced 16-pin SOIC) to form a complete FXS interface solution. Supply voltage is 3.13V to 5.25V with a typical 88 mA supply current and approximately 700 mW power dissipation; operating temperature is 0C to 70C. A SLIC (Subscriber Line Interface Concept) is the analog front-end IC that connects a central-office or customer-premises telephone line to a digital voice path, performing the BORSCHT functions (Battery, Over-voltage, Ringing, Supervision, Codec, Hybrid, Test). The SLIC category sits within the broader telecom interface IC family and is essential for VoIP gateways, embedded media gateways, and integrated access devices where legacy copper-pair connectivity must coexist with packetized voice. Key features include software-programmable internal balanced ringing to 90 VPK (5 REN to 4 kft, 3 REN to 8 kft), integrated battery supply with dynamic voltage generation, on-hook/off-hook detection, polarity reversal, and a PCM/SPI/GCI digital interface. The -C variant denotes the commercial (0C to 70C) temperature grade and the FM suffix denotes the 38-pin QFN (5x7) package. The part delivers >60 dB longitudinal balance and supports worldwide DC feed and ringing characteristics through firmware configuration rather than hardware strapping. The Si3215 ProSLIC architecture uses a high-voltage bipolar line-side driver controlled by an integrated low-voltage CMOS DSP-like controller; all ringing and feed parameters are loaded through the SPI control port at boot. Compared to discrete line-interface solutions built from individual op-amps, relays, and ringing generators, the ProSLIC dramatically reduces PCB area and BOM count while providing software-controlled country compliance. Typical applications include VoIP residential gateways, integrated access devices (IADs), cable embedded media terminals, PON/ONU voice port adapters, and small-office/home-office (SOHO) routers with FXS ports. The 90 VPK ringing and DTMF generation make it suitable for direct connection to analog telephones, faxes, or modems on the tip-and-ring copper pair. When designing with the Si3215-C-FM, observe the line-side surge and over-voltage protection guidance in the Si3215 datasheet; the Si3201 DC-DC controller must be co-designed for proper battery and ringing voltage generation. Decoupling must be placed within 2-3 mm of each supply pin to keep PCM and SPI buses free of switching noise from the internal DC-DC converters. This page synthesizes datasheet parameters from the manufacturer, distributor availability, and detailed comparison context for Skyworks ProSLIC family members that share the same 38-QFN footprint for drop-in PCB reuse.
SI3215-C-FT - 3.13-5.25V Telecom SLIC/CODEC | Skyworks Solutions
The Skyworks Solutions SI3215-C-FT is a single-channel Subscriber Line Interface Concept (SLIC) and CODEC for customer premise equipment, packaged in a 38-pin TSSOP. It operates from a 3.13 V to 5.25 V supply and consumes 88 mA, with listed power dissipation of 700 mW. The device performs the BORSCHT telephone-line functions and includes software-programmable internal balanced ringing up to 90 VPK. It is designed for 5 REN and 4 kft line conditions, with additional ringing support for 3 REN and 8 kft line lengths. Its GCI, PCM, and SPI interfaces support integration with a digital communications processor or system controller. The SI3215-C-FT also incorporates an integrated battery supply with dynamic operation, DTMF generation, and expanded telephony signaling capabilities for Japan and China country requirements. These characteristics make it suitable for analog telephone adapters, voice-over-IP gateways, customer premises equipment, and other embedded voice systems. Compared with discrete telephone-interface circuitry, the integrated SLIC and CODEC consolidate line termination, codec, ringing, and signaling functions into one programmable component. The 0°C to 70°C operating range supports commercial equipment deployments, while the TSSOP package supports conventional surface-mount assembly. Design evaluation should include line-length and REN requirements, ringing voltage and cadence, PCM or SPI host connectivity, thermal performance at 700 mW, and the external line-network components required by the manufacturer reference design.
SI3215-C-GM - Single-Channel SLIC/Codec | Silicon Labs
The Silicon Labs SI3215-C-GM is a single-channel programmable CMOS Subscriber Line Interface Concept and codec with integrated BORSCHT functions, operating from a 3.13 V to 5.25 V supply and drawing 88 mA typical supply current. The device is packaged in a 38-pin QFN surface-mount package measuring approximately 5 mm by 7 mm. A Subscriber Line Interface Concept, or SLIC, is a telecom interface integrated circuit that connects a telephone line to a digital voice system. It combines voice conversion, line-current control, ring-signal generation, tone generation, and telephone-signaling functions. In the signal chain, the SI3215-C-GM sits between the analog subscriber line and a PCM, GCI, or SPI digital interface, reducing the need for separate line-interface circuitry. Key features include software-programmable internal balanced ringing up to 90 VPK and support for up to 5 REN, subject to line-length and REN conditions. The device performs the BORSCHT functions required for subscriber-line supervision, while integrated DTMF generation supports telephone tone signaling. A 3.13 V to 5.25 V operating range accommodates both 3.3 V and 5 V system environments, while GCI, PCM, and SPI interfaces provide flexible connectivity to digital voice processors. The SI3215-C-GM integrates a DC-DC converter and battery supply, allowing the device to supply line-side operating power without a separate high-voltage supply design. This architecture is intended for economical single-channel or low-channel-count voice systems. Programmable ringing and line parameters permit adaptation to different country requirements, including the Japan and China signaling requirements identified in the manufacturer datasheet. Typical applications include subscriber-line access, voice-over-IP terminal equipment, digital loop carrier systems, voice gateways, embedded telephony controllers, and single-channel voice-processing boards. Its GCI, PCM, and SPI interfaces allow integration with a host processor, digital signal processor, or telephony application-specific circuit while retaining the required line-side functions in one package. Designers should pay close attention to the exposed-pad thermal path, high-voltage line connections, bypass-capacitor placement, and the requirements of the integrated DC-DC converter. Use the manufacturer reference circuit and pin-description table to define component values and board clearances. Do not substitute normal low-voltage routing practices for the line-side isolation and clearance shown by the application design. This page combines the SI3215-C-GM operating characteristics, interface options, replacement considerations, and practical implementation guidance in a form that supports initial component selection and board-layout planning. The manufacturer datasheet remains the controlling reference for final electrical limits, pin assignments, timing, and production design changes.
SI3215-FM - ProSLIC Programmable CMOS SLIC/Codec, 5 REN, 90Vpk | Skyworks
The Skyworks (formerly Silicon Laboratories) SI3215-FM is a ProSLIC programmable CMOS Subscriber Line Interface Circuit (SLIC) with integrated codec and ringing/battery voltage generation, housed in a 38-pin QFN (5x7 mm) package. It integrates the SLIC, codec, and battery generation functionality into a single CMOS IC, providing a complete analog telephone interface ideal for customer premise equipment (CPE) applications such as VoIP gateways, ATA adapters, and integrated access devices. What is a SLIC/Codec? A Subscriber Line Interface Circuit (SLIC) is a critical analog front-end IC that connects a digital telecom system to the analog 2-wire telephone subscriber line, performing DC feed, overvoltage protection, supervision (off-hook/on-hook/ring-trip detection), and 2-wire to 4-wire hybrid conversion. The codec digitizes the voice band signal for DSP processing. A ProSLIC integrates the SLIC, the codec, and the high-voltage battery/ringing supply generation on a single low-voltage CMOS die, dramatically reducing BOM count versus discrete SLIC + codec + boost-converter designs. Key features include software-configurable 5 REN internal ringing up to 90 Vpk without an external ringing generator, integrated DTMF/melody generation, and a comprehensive set of telephony signaling capabilities with expanded support of Japan and China country requirements. The device operates from a single low-voltage supply paired with the Si3201 line-driver companion IC, and supports both polarity-reversal and metering pulse generation needed for international billing standards. The ProSLIC architecture uses a low-voltage CMOS core driving a high-voltage external bipolar transistor array (via the Si3201), achieving the wide dynamic range and 1500V isolation typically required for tip-and-ring while keeping the primary silicon on a low-cost CMOS process. The integrated DC-DC controller eliminates the need for a discrete boost converter for ringing/battery generation. Typical applications include VoIP residential gateways, cable embedded MTA, optical network terminals (ONT/ONU), small-office/home-office (SOHO) routers with FXS ports, and wireless fixed-line terminals. The expanded Japan/China compliance makes it well suited for Asian telecom CPE designs. When designing with the SI3215-FM, the Si3201 line interface IC must be used as a companion device for the high-voltage tip/ring drivers; signal integrity between the two ICs is critical and the datasheet provides a reference PCB layout. Proper thermal management of the 38-QFN package is required for sustained ringing loads. This page synthesizes distributor pricing, drop-in alternative MPNs from the ProSLIC family, and PCB design notes not consolidated in the manufacturer datasheet, providing actionable information for telecom hardware engineers selecting FXS ports.
SI3215-FT - 90 VPK Programmable SLIC/Codec | Silicon Labs
The Silicon Labs SI3215-FT is a programmable CMOS subscriber line interface circuit and codec (ProSLIC) designed for customer-premise telecommunications equipment. It supports software-configurable internal ringing up to 90 VPK, operates with up to 5 REN at 4 kft, and supports up to 3 REN at 8 kft. The device is packaged in a 38-pin TSSOP and combines BORSCHT line functions, ringing and battery-voltage generation, voice codecs, and digital telephony signaling in one integrated circuit. A ProSLIC is a highly integrated telephone-interface IC used to connect a voice codec and digital line-control system to an analog subscriber line. Its programmable architecture replaces several discrete functions associated with BORSCHT line supervision, ring generation, battery feed, DTMF generation, and codec operation. This integration reduces external circuitry while allowing line behavior to be adjusted through device software rather than fixed external component networks. Key features include internal balanced ringing to 90 VPK, dynamically controlled battery voltage, DTMF generation, and software-programmable country-specific signaling. According to the manufacturer datasheet, the Si3215 family supports requirements associated with Japan and China. The integrated DC-DC converter controller continuously minimizes power by producing the battery voltage required for the current operating state from a single positive supply, reducing the need for a large external battery supply. The SI3215 is intended for single-channel CPE designs where analog telephone access must coexist with a digital voice processor. Its digital interfaces and programmable control allow the host system to manage line state, ring cadence, tone generation, and codec operations. A complete implementation must account for linefeed components, protection paths, ringing-network constraints, thermal margins, and host-specific register configuration. Typical applications include analog VoIP terminals, customer-premises telephony equipment, digital telephone adapters, voice-over-LAN endpoints, embedded telephony gateways, and legacy telephone-interface designs requiring programmable BORSCHT behavior. The 38-pin TSSOP package is also appropriate where a surface-mount single-channel solution is required but a higher pin-count QFN variant is not necessary. Designers should use the pin-description and typical application circuits in the manufacturer datasheet when assigning PCB nets and selecting the external line interface network. Validate ringing voltage, loop current, dc feed, thermal performance, and protection behavior in the final telephone equipment because these parameters depend on the line length, country-specific requirements, and external passive network. This page organizes the principal Si3215 capabilities into an application-focused guide, adds practical implementation considerations, and separates documented functions from parameters that must be confirmed in the complete manufacturer datasheet before a new board is released.
SI3215-GT - Programmable CMOS SLIC/CODEC | Silicon Labs
Silicon Labs SI3215-GT is a programmable CMOS subscriber line interface circuit and codec with integrated ringing and battery-voltage generation. It performs the line-side signaling functions used in voice-over-packet and digital telephone systems, supports software-configurable balanced ringing up to 90 VPK, and generates DTMF tones. The device is available in a 38-pin surface-mount package configuration identified in the Si3215 family documentation as TSSOP or QFN. A SLIC, or subscriber line interface circuit, is the analog and signaling interface between a telephone line and a digital voice-processing system. It forms part of the broader telephony interface hierarchy: SLIC > codec > integrated interface circuit > communications semiconductor. A ProSLIC combines the line-driver, codec, tone generation, ringing-generator, and battery-supply functions into a programmable device, reducing the number of separate components required in a voice endpoint design. The SI3215 supports software-configurable internal balanced ringing up to 90 VPK. The published ringing capability is stated as 5 REN at 4 kft and 3 REN at 8 kft, allowing the ringing load to be tailored to the line length and telephone-network environment. It also provides DTMF generation and comprehensive telephony signaling support, including requirements associated with Japan and China. An integrated DC-DC converter acts as the controller for a buck-boost converter that converts a positive supply into the negative battery voltage required by a conventional telephone line. Dynamic control of the battery voltage allows the converter to reduce the required level for a given operating mode, which can help lower power consumption while maintaining line functionality. The SI3215 family is suited to voice gateways, digital subscriber line equipment, analog telephone adapters, voice-over-IP terminals, embedded telephony systems, and other designs that connect one or more subscriber lines to a digital signal processor or system controller. Programmable operating characteristics make the same hardware platform adaptable to different ringing, battery, and signaling requirements. Careful line-interface design remains essential even though the codec and ringing functions are integrated. The external network, protection, transformer or coupling components, bypass capacitors, and power-conversion components must be selected for the intended voltage, current, ringing, and surge environment. Designers should also review the Si3215 data sheet before migrating a Si3210 design because the manufacturer explicitly identifies hardware and software differences between the two families. This product record combines the Si3215 family capabilities with practical migration, protection, layout, and sourcing guidance. It also distinguishes confirmed drop-in candidates from related family variants, helping engineers narrow the selection without treating package similarity as proof of complete electrical, software, and production compatibility.
SI3215-KT - 90 VPK Programmable SLIC/Codec | Silicon Labs
The Silicon Laboratories SI3215-KT is a programmable CMOS SLIC/codec with integrated ringing and battery-voltage generation, supporting up to 5 REN and 90 VPK internal ringing in a 38-pin TSSOP package. It consolidates subscriber-line interface, codec, tone generation, and line-voltage functions into one programmable device for telephone line-card designs. A SLIC, or subscriber-line interface circuit, is the analog front end between a telephone line and digital voice-processing circuitry. A COC, or codec, converts that analog voice signal into a digital PCM stream. The SI3215-KT combines these functions in a programmable CMOS IC, reducing external circuitry while allowing line parameters and signaling behavior to be configured through the device software. The SI3215-KT supports software-configurable internal ringing up to 90 VPK. The ringing capability accommodates 5 REN at 4 kft and 3 REN at 8 kft, providing flexibility across different line lengths and network loading conditions. It also includes DTMF generation, an integrated battery supply with dynamic voltage output, and an on-chip DC-DC converter that continuously minimizes power consumption during operation. The device provides the BORSCHT line-interface functions in programmable CMOS. Its telephone signaling capabilities include expanded support for Japan and China country requirements, making it suitable for regional line-card and voice-access equipment. The manufacturer datasheet also documents migration differences from the earlier Si3210, which is important when reusing software, hardware, or production test procedures. Typical uses include Voice-over-Packet adapters, digital loopback terminators, integrated access devices, analog telephone adapters, and subscriber-line access concentrators. A design can use the integrated codec path for digital voice transport while using the programmable SLIC functions to supervise the line, control DC feed, and generate ringing voltage without a separate line-interface processor. Layout is especially important because this device controls a high-voltage analog line interface alongside sensitive digital signaling. Follow the manufacturer datasheet for the 38-pin TSSOP footprint, decoupling placement, ground-return construction, and isolation boundaries. Keep switching and high-energy ringing pathways away from codec and clock traces to reduce susceptibility to noise and surge-induced disturbance. This page consolidates the SI3215-KT’s key line-card functions, sourcing guidance, application fit, and practical integration considerations. It also distinguishes verified device capabilities from specifications that require confirmation against the manufacturer datasheet, helping engineers plan a design before finalizing the PCB, firmware, and production test strategy.
SI3215M-BT - 3.3V Single-Channel ProSLIC | Silicon Labs
The Silicon Labs SI3215M-BT is a 3.3 V, single-channel programmable CMOS Subscriber Line Interface Codec, or ProSLIC, packaged in a 38-pin TSSOP. It integrates the analog telephone-line interface and codec functions required in customer premise equipment, while supporting ringing and battery-voltage generation. The SI3215M-BT operates from a single 3.3 V supply and can control the phone line through a Silicon Labs Si3201 linefeed interface chip or a discrete linefeed circuit. A ProSLIC is a programmable integrated circuit that places a telephone-line interface into the analog domain. In the broader hierarchy, it belongs to interface ICs, then telecommunications interface silicon, then customer premise equipment and voice-access semiconductors. Unlike a simple codec, the SI3215M integrates line-driving, ring-voltage generation, battery-voltage generation, voice processing, and programmable telephone-line control. This consolidation reduces the number of external line-interface functions required in voice terminal equipment. The SI3215M-BT provides one integrated SLIC channel in an industrial-temperature option. It uses a 3.3 V supply, supports programmable CMOS telephone-interface operation, and includes ringing and battery-voltage-generation functions. Its 38-pin gull-wing TSSOP package is intended for surface-mount PCB assembly. The package provides 38 terminations for the mixed-signal, control, supply, and line-interface functions defined by the device pin description. The integrated battery supply adapts its output voltage to reduce power consumption, allowing the system to operate from the single 3.3 V rail identified for the SI3215M variant. The ringing generator supports the telephone line through the external linefeed path. This division of responsibility allows the SI3215M-BT to control line voltage while the Si3201 or discrete components carry the line current and isolate the low-voltage codec circuitry from the analog line. Typical uses include analog telephone adapters, voice-over-IP terminals, customer premise equipment, analog fax equipment, and voice-access gateways. In these applications, the device handles the analog line interface and voice-signal conversion while a host processor controls programmable operating parameters. The single-channel architecture is particularly appropriate for one-line terminals rather than multi-line systems requiring parallel channel expansion. PCB implementation must preserve separation between the low-voltage digital and analog circuitry and the telephone-line network. Decoupling should be placed close to the supply pins, while linefeed and protection components should follow the reference circuit in the manufacturer datasheet. Component values associated with the ring generator, battery supply, and external linefeed network should not be changed without reviewing the recommended operating limits. This product page combines the exact SI3215M-BT package and supply information with practical interface-IC design guidance, application context, package hierarchy, and drop-in family comparisons. It also identifies which detailed electrical limits and pin assignments should be confirmed in the manufacturer datasheet before schematic release or PCB layout approval.
SI3215M-C-FMR - Single-Channel SLIC/Codec w/ MOSFET DC-DC | Skyworks
The Skyworks Solutions (formerly Silicon Labs) SI3215M-C-FMR is a single-channel ProSLIC programmable CMOS Subscriber Line Interface Circuit (SLIC) with integrated codec, ringing, and MOSFET-based DC-DC converter, packaged in a 38-pin QFN (5x7 mm). It operates from a 3.13 V to 5.25 V supply, draws 88 mA typical supply current, and dissipates up to 700 mW while performing all BORSCHT functions on a single twisted-pair line. An SLIC (Subscriber Line Interface Circuit) is a mixed-signal IC used in VoIP gateways, central-office line cards, and DSLAM/PON ONU platforms to interface between the digital PCM/ SPI bus of a host processor and the analog 2-wire subscriber line. The SLIC handles Battery feed, Over-voltage protection, Ringing, Supervision, Coding, Hybrid, and Test (BORSCHT). Modern single-chip ProSLICs integrate the codec, battery switcher, and ringing waveform generator, replacing dozens of discrete analog components that older designs required. SI3215M-C-FMR is part of the Si3215 family that integrates a MOSFET-driver DC-DC converter, eliminating the external BJT or inductor typically required for the line-side battery feed. Key features include software-programmable internal balanced ringing up to 90 VPK (5 REN to 4 kft, 3 REN to 8 kft), an integrated battery supply with dynamic voltage control, low-power standby, and on-hook transmission. The 'M' suffix denotes the MOSFET-output variant (Si3215 without the M uses an external BJT/inductor), and the polarity of DCFF vs DCDRV is the only circuit difference between the two versions. Host interface options include PCM, GCI, and SPI for flexible connection to most VoIP SoCs. Typical applications include VoIP residential gateways, integrated access devices (IADs), PON/GPON ONTs, cable eMTA, small-office PBX line cards, and industrial FXO/FXS adapters. The integrated MOSFET driver cuts BOM cost and board area versus BJT-based SLICs. When designing with SI3215M-C-FMR, ensure the DC-DC converter's MOSFET and catch diode meet the peak ringing/battery-feed current demand; verify thermal dissipation on the QFN exposed pad and follow Skyworks reference layout for EMI/ESD compliance. This page synthesizes distributor pricing from 8+ sources, drop-in pin-compatible Si3215 family alternatives, and practical design notes not found on the manufacturer datasheet.
SI3216-BT - 38-TSSOP Voice SLIC/CODEC | Silicon Labs
Silicon Labs SI3216-BT is a single-channel ProSLIC analog telephone interface with GCI, PCM, and SPI interfaces, a 3.13 V to 5.25 V supply range, and a 38-pin TSSOP package. It supports wideband audio from 50 Hz to 7.0 kHz and narrowband audio from 200 Hz to 3.4 kHz, including 16-bit voice processing at a 16 kHz sampling rate. A SLIC, or subscriber line interface circuit, is the analog front end used to connect a telephone line to a digital voice system. It belongs to the codec and telephone-interface hierarchy within integrated interface ICs. By combining line-interface circuitry with voice encoding functions, the SI3216-BT is designed for Voice-over-IP gateways, analog terminal adapters, voice gateways, and other equipment that connects a copper-wire telephone line to a digital voice processor. The SI3216-BT combines a 1-channel SLIC/CODEC architecture with support for both wideband and narrowband operating modes. Its stated supply current is 88 mA, its rated power dissipation is 700 mW, and its operating temperature range is -40°C to +85°C. GCI, PCM, and SPI interfaces give system designers several paths for connecting the device to line-processing and control electronics. The industrial-temperature grade suits equipment expected to operate across extended commercial temperature environments. Technical operation depends on a low-voltage CMOS implementation operating from 3.13 V to 5.25 V. Wideband mode covers 50 Hz to 7.0 kHz for enhanced-voice systems, while narrowband mode covers 200 Hz to 3.4 kHz for conventional telephony. The 16-bit, 16 kHz codec capability supports digital voice processing with a 50% sampling margin relative to an 8 kHz narrowband voice channel, while wideband speech remains compatible with the specified 7.0 kHz audio bandwidth. Typical applications include VoIP analog terminal adapters, digital subscriber line equipment, voice-over-PBX gateways, voice-over-cable terminal adapters, and embedded analog telephone interfaces. Its principal design value is integrating the subscriber-line interface and codec into one device, reducing the number of separate analog and digital interface blocks required in a voice terminal. Layout and power-supply design remain critical in a high-gain telephone interface. Place bypass and decoupling capacitance close to the supply pins, keep sensitive analog routing away from digital switching signals, and follow the manufacturer’s reference-layout guidance. Verify line-side protection, grounding, and maximum operating voltages against the requirements of the target telephone network before releasing production hardware. This product record combines electrical specifications, interface details, application guidance, and a verified same-family alternative comparison. It is intended to help engineers confirm electrical, packaging, lifecycle, and design requirements before integrating the SI3216-BT into a telephone-interface design.
SI3216-C-FM - 38-QFN Single-Channel SLIC Codec | Skyworks
Skyworks Solutions Inc. SI3216-C-FM is a single-channel Subscriber Line Interface Concept and codec IC with GCI, PCM, and SPI interfaces, an 88 mA typical supply current, and a 3.13 V to 5.25 V operating supply range. The device is packaged in a 38-QFN surface-mount package measuring 5 mm by 7 mm. A Subscriber Line Interface Concept, or SLIC, is an integrated telephone-line interface that connects a communications system to an analog subscriber loop. A SLIC typically handles line-current control, voice-band signal processing, and the analog-to-digital and digital-to-analog conversion required by the voice codec. Within the product hierarchy, the SI3216-C-FM is an interface IC, telecom interface IC, and subscriber line access circuit. The SI3216-C-FM provides one SLIC channel with dual-mode wideband operation extending to 7 kHz and narrowband operation extending to 3.4 kHz. Its integrated codec supports 16-bit, 16 kHz sampling for enhanced voice processing. These features allow a compact voice endpoint to support both wideband and narrowband calls when the surrounding line interface and network equipment provide the corresponding signaling functions. The device operates from 3.13 V to 5.25 V and draws 88 mA under the stated operating condition. Its listed power dissipation is 700 mW, which makes thermal design and exposed-pad heat flow important in compact subscriber-premises equipment. The combination of a single-channel architecture, selectable voice bandwidth, and multiple digital interfaces supports centralized channelization where each subscriber line has one associated SLIC channel. Typical applications include central-office line-card equipment, subscriber-premises equipment, voice-over-IP access circuits, digital loop carriers, and other telephony systems requiring a narrowband or wideband codec. The PCM interface suits equipment transporting voice samples through a digital backplane, while GCI and SPI provide additional options for line-card control and configuration. Place input and output decoupling capacitors close to the supply pins, connect the exposed pad to a low-impedance ground plane, and follow the manufacturer pin-description table when assigning tracks. Confirm the external feed-resistor value, line-interface topology, and codec clock arrangement against the manufacturer datasheet before releasing a PCB because these details affect line current, voice quality, and signal integrity.
SI3216-C-FT Single-Channel Wideband SLIC/Codec | Skyworks
Skyworks Solutions SI3216-C-FT is a single-channel wideband Subscriber Line Interface Concept and codec with GCI, PCM, and SPI interfaces. It operates from a 3.13 V to 5.25 V supply, consumes 88 mA, and is housed in a 38-pin TSSOP package. The device also includes a BJT/inductor DC-DC converter and supports wideband and narrowband voice operation. A Subscriber Line Interface Concept, or SLIC, is an integrated analog interface that connects a telecommunications line to digital voice-processing equipment. A SLIC/codec combines functions such as line-driver control, voice-band signal conversion, and digital voice transport. The SI3216-C-FT places these functions into one interface IC for single-channel line-card, voice-gateway, and analog-handset designs, reducing the number of external interface components required. Key features include dual-mode wideband operation up to 7 kHz and narrowband operation up to 3.4 kHz. Its 16-bit, 16 kHz sampling format supports enhanced voice-processing designs. Digital connectivity through GCI, PCM, and SPI gives the device flexibility for connecting with voice codecs, processors, line-card controllers, and other telecommunications equipment. The operating temperature range is 0 °C to 70 °C, making the part suited to controlled commercial telecom environments. The SI3216-C-FT integrates a BJT/inductor DC-DC converter to support the line interface and associated voltage-generation requirements. The converter topology is significant because the SLIC must handle a line-side voltage environment while preserving a regulated low-voltage supply for its internal codec and control logic. The manufacturer specifies a maximum power rating of 700 mW, but designers should evaluate actual dissipation from the supply voltage, operating mode, and line conditions rather than treating the rating as continuous dissipation. Typical uses include telephone line cards, voice gateways, subscriber-line access equipment, and analog handsets. For a new design, the three digital interfaces allow the vendor to select the most appropriate connection to the host processor: GCI for compatible line-interface controllers, PCM for digital PCM streams, or SPI for a compact host-control connection. External component selection and protection must follow the manufacturer’s recommended application circuit. The most important design consideration is preserving the intended line-side power and signal environment. Keep the SLIC’s sensitive analog paths compact, follow the manufacturer’s grounding and decoupling guidance, and account for the DC-DC converter’s magnetic-component layout. Confirm that the selected magnetics and protection network support the target line voltage, ringing, current, and codec bandwidth. This page provides a structured comparison with related single-channel SLIC/codec variants, practical application guidance, package information, and purchasing information for engineers evaluating the SI3216-C-FT for single-channel voice interfaces.
SI3216-C-GM - Single-Channel SLIC Codec, 3.3V/5V | Skyworks Solutions
Skyworks Solutions SI3216-C-GM is a single-channel Subscriber Line Interface Concept and codec integrated circuit designed for telecom line-card applications. The device operates from a 3.13 V to 5.25 V supply, accepts GCI, PCM, or SPI interfaces, and is specified for a -40°C to +85°C operating-temperature range. It is packaged in a 38-pin QFN measuring approximately 5 mm by 7 mm. The device also integrates a 60 dB SLIC signal path and a DC-DC converter for high-speed telecom interface applications. A Subscriber Line Interface Concept, or SLIC, is the analog front end used to connect a central-office telephone line to a digital switching system. A traditional SLIC provides line termination, voice-band filtering, transmit and receive amplification, and line-power control. The SI3216-C-GM combines these functions with digital codec and control interfaces, allowing a telecom access circuit to use a compact single-chip signal path. Its GCI, PCM, and SPI interface options place it within the broader hierarchy of telecom interface ICs, interface ICs, and semiconductors. Key specifications include one SLIC channel, a supply-voltage range of 3.13 V to 5.25 V, 88 mA supply current, and a listed power dissipation of 700 mW. The device supports narrowband operation to 3.4 kHz and dual-mode wideband operation to 7 kHz with 16-bit, 16 kHz sampling, as described in the product listing. Its 60 dB signal parameter makes it suitable for voice and wideband line-card designs where channel count, supply flexibility, and integrated telephony functions are important. The SI3216-C-GM uses an integrated BJT/inductor DC-DC converter architecture to support telecom line-power and interface requirements. The converter and SLIC functions are consolidated into the same 38-QFN package, reducing the number of discrete components required around a line interface. The exposed-pad package provides a thermal path to the PCB, making copper pour and layout symmetry important for predictable junction-temperature behavior. Typical applications include Voice over IP line cards, broadband access terminals, digital subscriber line equipment, PSTN line interfaces, embedded voice gateways, and industrial telecom control systems. In a Voice over IP design, the SLIC can handle the analog telephone-line side while PCM or SPI connects to a digital processor. For legacy telephone equipment, the same device can support narrowband voice or dual-mode wideband operation, subject to the system clocking and line-network requirements. Designers should follow the manufacturer’s recommended decoupling, exposed-pad, and high-speed trace-layout practices. Place input and output capacitors close to their associated pins, connect the exposed thermal pad to a properly sized ground plane, and keep analog line interfaces away from switching and digital return currents. Confirm the intended supply rail, line-power limits, protection network, and interface timing before releasing the PCB layout. This page combines the manufacturer-oriented part identity with distributor listings, interface and supply specifications, package information, drop-in family alternatives, and practical PCB and thermal considerations. It is intended to accelerate engineering selection while keeping the distinction between verified specifications and application-specific design assumptions explicit.
SI3216-FT 1-Channel SLIC Codec, 38-TSSOP | Silicon Labs
The Silicon Labs SI3216-FT is a single-channel Subscriber Line Interface Concept and codec integrated circuit with GCI, PCM, and SPI interfaces, supplied in a 38-pin TSSOP package. Its operating supply range is 3.13 V to 5.25 V, with an 88 mA supply current and a listed power dissipation of 700 mW. The device supports dual-mode wideband and narrowband voice operation, including wideband audio to 7 kHz and narrowband audio to 3.4 kHz. An SLIC is an analog telephone-line interface that provides the bridge between a conventional subscriber line and digital switching equipment. The integrated codec portion converts voice signals into digital PCM data, while the SLIC circuitry handles line-facing functions. The SI3216-FT belongs to the interface IC category, where signal conditioning, line-interface control, and voice encoding must operate together within strict supply and board-space constraints. The principal features include one SLIC channel, 16-bit voice sampling at 16 kHz, and support for GCI, PCM, and SPI control paths. These interfaces provide options for connecting the device to digital switching, channel-bank, or host-control circuitry. The 3.13 V minimum operating voltage permits integration with systems operating below the traditional 5 V supply level, while the 5.25 V maximum supports legacy 5 V infrastructure. The SI3216-FT combines narrowband and wideband voice support in one device. Narrowband operation reaches 3.4 kHz, while wideband operation extends to 7 kHz, allowing the same design framework to support conventional voice and higher-fidelity speech. The 38-TSSOP package provides a surface-mount form factor for compact telecommunications equipment, although its relatively long body requires careful PCB layout and adequate pin clearance. Typical uses include voice-over-IP terminals, subscriber-line access equipment, digital loop carriers, voice gateways, and fixed-line analog adapters. In these systems, the codec generates digital voice samples while the SLIC interface connects to an analog telephone line. The supported 16-bit, 16 kHz format can also simplify synchronization with compatible PCM processing paths. Designers should account for the 700 mW listed power dissipation and provide stable, low-noise supply rails around the 3.13 V to 5.25 V operating range. Place decoupling capacitors close to the supply pins and maintain the recommended layout around analog, digital, and line-interface circuitry. Confirm external line-network components, protection requirements, clocking, and interface levels against the manufacturer datasheet before production release. This page combines the core electrical specifications, interface choices, application guidance, and verified same-footprint alternatives for the SI3216-FT. It also highlights the distinction between electrically similar options so that replacement decisions can be based on package compatibility, supply operation, temperature grade, interface behavior, and documented performance rather than part-number similarity alone.
SI3216-GT - Wideband ProSLIC Codec 38-TSSOP | Silicon Labs
The Silicon Labs SI3216-GT is a low-voltage CMOS ProSLIC analog telephone interface and audio codec with one subscriber line channel, 3.13 V to 5.25 V supply operation, and a 38-pin TSSOP package. It supports wideband and narrowband telephony audio through GCI, PCM, and SPI interfaces while providing 16-bit audio sampling at 16 kHz for enhanced voice quality. A ProSLIC, or Subscriber Line Interface Circuit, is an integrated analog telephone interface that connects a voice codec to a customer-premises line. The Si3216 combines line-interface and codec functions within a voice-over-IP access device, placing it in the hierarchy of telecom interface ICs, telephone-line interface circuits, codecs, and system semiconductors. Its wideband mode supports audio from 50 Hz to 7 kHz, while narrowband mode covers 200 Hz to 3.4 kHz. Key features include dual-mode audio operation, a 16-bit codec operating at a 16 kHz sample rate, and support for GCI, PCM, and SPI interfaces. The stated supply current is 88 mA, the listed power dissipation is 700 mW, and the documented operating-temperature range is -40°C to 85°C. These characteristics suit compact CPE designs requiring one analog line endpoint and digital voice transport. The Si3216 is designed for Voice-over-IP terminals, voice gateways, access equipment, and other CPE products that benefit from wider speech bandwidth than traditional 3.4 kHz telephony. Its digital interfaces allow the codec section to connect to a system controller or digital signal processor, while its analog telephone interface handles the subscriber line. The multiple interface options also support designs that use either serial packet audio or parallel PCM signaling. Designers should provide suitable line-interface protection and separation circuitry around the analog telephone section and verify the external network requirements of the target CPE design. Decoupling should follow the manufacturer datasheet recommendations, with short, low-inductance supply connections helping limit susceptibility to switching noise on digital and analog rails. This page organizes the key SI3216-GT operating limits, interface capabilities, application fit, and verified drop-in candidates. It also provides practical sourcing, package, thermal, and design guidance for engineers evaluating the part in legacy or ongoing voice-access hardware. Alternative sourcing, lifecycle confirmation, and current lead-time requests can be handled through the Request a Quote form on this page, while the manufacturer datasheet remains the controlling reference for pin connections and application implementation.
SI3216-KT 38-TSSOP Wideband SLIC Codec | Silicon Labs
Silicon Labs SI3216-KT is a low-voltage CMOS ProSLIC integrated telephone interface and audio codec designed for Voice-over-IP equipment. The single-channel device supports wideband audio from 50 Hz to 7.0 kHz and narrowband audio from 200 Hz to 3.4 kHz, with 16-bit operation and 16 kHz sampling for wideband voice. It is packaged in a 38-pin TSSOP and operates from 3.13 V to 5.25 V. A Subscriber Line Interface Concept, or SLIC, is a semiconductor category that combines analog telephone-line interface functions with digital codec processing. In the power-management and communications hierarchy, the SI3216-KT belongs to the SLIC and codec class within interface ICs. Its purpose is to bridge a conventional analog telephone line and a digital voice-processing system, allowing a VoIP endpoint to support voice-band or wideband conversations while the host handles packetization and call control. The SI3216-KT combines wideband and narrowband codec modes in one device. The wideband path covers 50 Hz to 7.0 kHz, while the narrowband path covers 200 Hz to 3.4 kHz. According to the Silicon Labs Si3216 datasheet, it is a low-voltage CMOS device intended for enhanced-voice VoIP applications. Its listed operating supply range of 3.13 V to 5.25 V supports both 3.3 V and 5 V system rails, subject to the detailed limits and tolerances stated by the manufacturer. The component includes GCI, PCM, and SPI interfaces, giving a system designer several ways to connect the codec to external controller or line-interface circuitry. The verified specifications identify one codec circuit, 88 mA supply current, 700 mW power, a 0°C to 70°C operating range, and a 60 dB signal parameter in a 38-pin TSSOP package. Exact timing, line-driver current, gain distribution, hook-state thresholds, and absolute maximum limits must be taken from the manufacturer datasheet before final circuit design. Typical uses include VoIP analog telephone adapters, voice terminals, residential gateways, digital phone systems, and embedded voice processors. The wideband mode is useful when the network and signal chain can support a 16 kHz sampling rate, while narrowband mode preserves compatibility with conventional 200 Hz to 3.4 kHz telephony speech. The same-package SI3216M-KT and SI3216-FT are relevant cross-reference candidates for procurement and board-level planning, subject to suffix-specific qualification checks. The primary design consideration is the telephone line interface around the IC. A production design must follow the manufacturer’s recommended external network, protection, filtering, and component-selection circuits rather than treating the SI3216-KT as a standalone codec. PCB placement should minimize analog and digital coupling, provide appropriate ground-plane continuity, and place required bypass and interface components close to their associated pins. This product page consolidates the device’s electrical limits, package identity, operating modes, searchable specifications, comparison candidates, and application guidance. It also distinguishes verified SI3216-KT attributes from parameters that still require direct consultation of the manufacturer datasheet, helping engineers move from component identification to qualified design review without relying on generic SLIC assumptions.
SI3216M-BT Single-Channel SLIC Codec, 3.3-5 V | Silicon Labs
The Silicon Labs SI3216M-BT is a single-channel subscriber line interface codec designed for telecom line-card and voice-over-IP applications. It supports a 3.13 V to 5.25 V supply range, draws 88 mA, and operates from -40 °C to +85 °C. The device is offered in a 38-pin TSSOP package and supports GCI, PCM, and SPI interfaces. A SLIC codec is a telecom interface integrated circuit that connects a subscriber telephone line to a digital voice system. The SLIC portion handles the analog line interface, while the codec portion converts voice between analog and digital formats. Within the product hierarchy, SI3216M-BT is a SLIC codec, telecom interface IC, and mixed-signal semiconductor designed for line-card equipment. The SI3216M-BT provides dual-mode voice operation covering wideband channels to 7 kHz and narrowband channels to 3.4 kHz. It performs 16-bit voice sampling at 16 kHz, providing the digital signal format required by contemporary digital telephony systems. Its 88 mA supply current and 700 mW power rating characterize the operating demands of this integrated telecom interface. The integrated battery supply continuously adapts its output voltage to reduce power consumption. This adaptive approach allows the complete solution to operate from a single 3.3 V supply for the SI3216M version or a 5 V supply. GCI, PCM, and SPI connectivity permits connection to different line-card processors and digital transport architectures without changing the basic line interface function. Typical uses include ADSL and VDSL line cards, voice gateways, digital loop carriers, central-office line-card equipment, and access-network terminals. Its single-channel architecture is appropriate when one subscriber line requires a dedicated codec, while a multi-line card can combine several devices around a common processor interface. Designers should account for the difference between the external logic supply and the internal battery-feed operating domain. PCB layout must preserve the separation of analog and digital return paths, follow the reference-ground recommendations in the manufacturer datasheet, and provide adequate thermal dissipation for the device's 700 mW power rating. This page combines the device's electrical limits, interface capabilities, functional alternatives, and application-oriented engineering guidance. It also identifies the package and documentation details needed to assess SI3216M-BT during component selection, PCB planning, sourcing, and legacy telecom-platform maintenance.
SI32171-C-GM1 - 1-Channel FXS ProSLIC, 42-QFN | Skyworks
The Skyworks SI32171-C-GM1 is a single-channel ProSLIC (Subscriber Line Interface Concept) device in a 42-pin QFN (5x7 mm) package that delivers a complete foreign-exchange-station (FXS) telephony interface with integrated DC-DC controller, low-power ringing, and PCM/SPI host interface. It is rated for -110 V ringing operation, integrates DTMF detection, and supports both 3.3 V and 1.8 V I/O from a 3.3 V supply. A ProSLIC (Subscriber Line Interface Concept) is a highly integrated mixed-signal IC that replaces dozens of discrete components traditionally needed to interface a digital system-on-chip to the analog two-wire telephone subscriber line. In the system hierarchy, the ProSLIC sits between the host SoC (or DSP) and the tip/ring pair, performing the BORSCHT functions (Battery feed, Over-voltage protection, Ringing, Supervision, Coding, Hybrid, and Testing). As an FXS device, it provides the central office side of the analog subscriber loop and is fundamental to VoIP gateways, integrated access devices, and fixed-line terminal adapters. Key features include a complete single-channel FXS solution, automatic battery voltage generation via the integrated DC-DC controller, internal balanced or unbalanced ringing with patented low-power ringing, global programmability for LSSGR/ITU/ETSI line standards, simplified configuration/diagnostics, and DTMF detect on-chip. The 5x7 mm footprint and reduced BOM significantly shrink the PCB area versus discrete line-interface designs. Technically, the Si3217x family uses CMOS mixed-signal design with on-chip high-voltage charge-pump drivers, an integrated DC-DC switching controller that derives optimal battery voltages per line state, and a Sigma-Delta codec pair for the transmit/receive paths. The automatic battery-voltage tracking dynamically minimizes power dissipation in on-hook, off-hook, and ring states, while the low-power ringing architecture avoids the bulky external ring relay in many designs. Typical applications include VoIP residential gateways, xDSL integrated access devices (IADs), cable telephony eMTA, fiber-to-the-home (ONT/ONU) voice ports, fixed wireless terminals, and small-office/home-office analog terminal adapters (ATAs). It is also used in industrial remote-metering and alarm panels where a single analog FXS port is required. When designing with this part, attention must be paid to the DC-DC inductor selection, line-side protection component choice (over-voltage, surge, PTC), and PCB creepage/clearance between the high-voltage traces and the low-voltage digital interface. The exposed thermal pad must be soldered to a sufficient ground pour for heat dissipation during sustained off-hook or ring states. This page synthesizes distributor pricing, drop-in family variants, and practical design notes not found in the manufacturer datasheet alone, enabling faster BOM selection and supply-chain risk assessment for ProSLIC-based FXS designs.
SI3220-BQ Dual ProSLIC 3.3V/5V 64-TQFP | Silicon Labs
Silicon Labs SI3220-BQ is a dual-channel ProSLIC integrated circuit combining SLIC and codec functions in a 64-pin TQFP package. It operates from a single 3.3 V or 5 V supply, supports PCM, SPI, and GCI digital interfaces, and provides two analog telephone-line channels with integrated balanced ringing to 65 Vrms. The device consumes 65 mA and is specified for operation from -40 °C to +85 °C. A ProSLIC is a programmable subscriber-line interface circuit that consolidates multiple functions of a traditional analog telephone linecard. The SI3220 combines the SLIC, codec, and digital interface sections into one low-voltage CMOS device, while the companion Si3200 linefeed interface performs the external high-voltage functions. This division keeps high-voltage isolation and protection circuitry separate from the low-voltage signal-processing section. Key features include dual-channel operation, all BORSCHT functions, internal balanced ringing to 65 Vrms, low standby consumption, and support for applications up to 18 kft. The programmable digital interface can use standard PCM, SPI, or GCI connections, allowing the device to fit voice gateways, linecards, voice-over-packet systems, and digital PBX platforms. The 3.3 V and 5 V supply options provide flexibility across different linecard architectures. Internally, the SI3220 handles the low-voltage codec, line-driver, and digital control functions required by a dual analog channel. PCM or SPI connectivity carries voice and control traffic between the ProSLIC and host equipment, while GCI provides an alternative digital interface format. The companion Si3200 supplies the high-voltage linefeed path, including the external components needed to support ringing and telephone-line operation. Typical uses include two-channel analog telephone interfaces, broadband voice gateways, PBX linecards, Voice over Ethernet endpoints, digital loopback systems, and embedded voice adapters. For a new two-channel design, the SI3220-BQ is most suitable when the board architecture separates low-voltage codec and SLIC processing from high-voltage linefeed circuitry through Si3200 or Si3202 devices. The primary design consideration is the division between low-voltage and high-voltage sections. Maintain the isolation and creepage requirements of the telephone-line interface, place protection components near the line connectors, and validate the complete linecard against the applicable linefeed network and ringing requirements rather than relying on the SI3220 alone. This product data connects the SI3220-BQ specifications with compatible companion silicon, interface requirements, and design considerations, helping engineers identify the correct roles for the ProSLIC, linefeed interface, digital host interface, and external protection network.
SI3220-FQ - Dual-Channel SLIC/CODEC, 64-TQFP | Skyworks Solutions
The Skyworks Solutions SI3220-FQ is a dual-channel Subscriber Line Interface Concept and codec integrated circuit with GCI, PCM, and SPI interfaces, a 64-pin TQFP package measuring 10 mm by 10 mm, 3.3 V or 5 V operation, and a typical 65 mA supply current. It integrates two analog telephone-line channels with codec functionality for subscriber line access equipment. A SLIC is a semiconductor interface between a public switched telephone network line and a digital voice system, while a codec converts analog voice signals into digital PCM data. Integrating both functions into one IC reduces component count and simplifies dual-channel telephone interface designs. The SI3220-FQ supports GCI, PCM, and SPI control and data interfaces, allowing it to connect with a line-processing controller, DSP, or system processor. The SI3220-FQ performs the complete BORSCHT line-interface functions and supports applications operating with line lengths up to 18 kft. Its internal balanced ringing generator provides up to 65 Vrms, allowing the device to implement ringing on both channels without a separate balanced ringer circuit. These integrated functions reduce board area while retaining the line supervision, codec, and ringing capabilities required by analog telephone equipment. The device operates from either 3.3 V or 5 V and has a listed maximum power dissipation of 941 mW. Its specified operating-temperature range is 0°C to 70°C, making it appropriate for commercial-temperature subscriber line access, voice-over-IP endpoint, digital loop carrier, and analog telephone interface applications where environmental conditions remain within that range. Typical deployments include two-channel voice gateways, office telephone interfaces, central-office line cards, voice-over-IP adapters, and digital loop carrier equipment. The dual-channel architecture provides two analog line interfaces in one package, while the 64-TQFP construction simplifies assembly through standard surface-mount handling. Designers should follow the manufacturer pin-description table when assigning PCB tracks and should provide suitable bypass capacitors at the supply pins. Because the internal ringer can reach 65 Vrms, creepage, isolation, component spacing, and protection-network design require careful review. Confirm that the 0°C to 70°C temperature range, 941 mW power rating, and 18 kft application limit satisfy the intended deployment. This page combines the SI3220-FQ interface, channel-count, power, ringing, temperature, and package specifications with application guidance and a same-package selection analysis. It also distinguishes verified attributes from parameters that require confirmation in the manufacturer datasheet or design qualification process.
SI3220-G-FQ - Dual-Channel SLIC/Codec 64-TQFP | Skyworks
The Skyworks Solutions SI3220-G-FQ is a dual-channel Subscriber Line Interface Concept and codec integrated circuit with internal 65 Vrms balanced ringing, internal diagnostics, GCI, PCM, and SPI interfaces, and a 65 mA operating supply current. It is packaged in a 64-pin TQFP measuring 10 mm by 10 mm for surface-mount telecom and voice-over-IP equipment. A Subscriber Line Interface Concept, or SLIC, is the analog-facing portion of a voice terminal device. It interfaces with the telephone line, provides line-driving and sensing functions, and works alongside a codec that converts between analog voice signals and digital PCM data. The SI3220-G-FQ integrates both functions into one device, reducing board area and simplifying the connection between the line interface and the system controller. Key features include two integrated voice channels, support for 3.3 V and 5 V operation, a typical operating supply current of 65 mA, and internal balanced ringing rated at 65 Vrms. The GCI interface supports general-purpose hardware control, while PCM and SPI interfaces provide digital links to codecs, DSPs, and system controllers. Operating temperature is specified from 0°C to 70°C, and the device is offered in a lead-free 64-TQFP package. The SI3220-G-FQ is implemented as a programmable CMOS SLIC and codec. Its integrated ringing and diagnostics features help a system detect line conditions and reduce reliance on external test equipment. Because the device is designed for subscriber-line access, its operating characteristics and interface set must be evaluated together with the target line voltage, transformer or external termination network, digital host interface, and regional voice requirements. Typical applications include voice-over-IP analog adapters, digital subscriber line equipment, voice gateways, analog terminal adapters, central-office line-card modules, and carrier-grade voice interfaces. The dual-channel architecture allows one package to serve two analog voice paths, provided the board satisfies the appropriate line-isolation, surge, thermal, and routing requirements. Designers should follow the manufacturer reference circuit for line termination, ringing capacitors, clocking, digital interfaces, and decoupling. Because this is a line-facing integrated circuit, printed-circuit-board creepage, isolation components, protection networks, and analog-versus-digital partitioning can be as important as the logic interface itself. Confirm the exact pin arrangement and recommended external network against the manufacturer datasheet before layout release. This page combines the device specifications, package information, drop-in alternatives, application guidance, and design notes needed to evaluate the SI3220-G-FQ for telecom, voice gateway, and subscriber-line designs.
SI3220-G-GQ - Dual-Channel SLIC/CODEC 64-TQFP | Skyworks
Skyworks Solutions Inc. SI3220-G-GQ is a dual-channel Subscriber Line Interface Concept and codec integrated-circuit interface designed for analog telephone-line termination. The device provides two SLIC channels, supports 3.3 V and 5 V operation, and is packaged in a 64-pin TQFP measuring 10 mm by 10 mm. Its integrated balanced ringing generator produces 65 Vrms output, while internal diagnostics support board-level line-interface testing. The SI3220-G-GQ is identified as a lead-free part and is intended for dual-channel telephone access and voice-over-network equipment. A Subscriber Line Interface Concept, or SLIC, is the analog-facing portion of a telephone subscriber-line interface. It terminates the line, manages line power, signaling, and voice-frequency signals, and provides the bridge between the analog telephone network and a digital voice-processing system. A codec performs the complementary analog-to-digital and digital-to-analog conversion functions. Integrating both functions into one IC reduces component count and simplifies the design of dual-channel voice cards, foreign-exchange equipment, voice gateways, and analog telephone adapters. The SI3220-G-GQ combines two complete SLIC/codec channels with interfaces identified as GCI, PCM, and SPI. It supports supply voltages of 3.3 V and 5 V, with a listed supply current of 65 mA and an operating temperature range from -40 °C to +85 °C. The internal 65 Vrms balanced ringing source eliminates the need for a separate balanced ringer circuit in designs that use this feature. Internal diagnostics add another practical benefit by allowing line conditions to be examined through the device's control interface. The SI3220-G-GQ belongs to the ProSLIC family of low-voltage CMOS devices designed to implement complete dual-channel analog telephone interfaces. Its architecture combines line termination, integrated codec functionality, ringing generation, and diagnostics in one package. The 64-TQFP construction provides a defined lead arrangement for conventional surface-mount assembly, while the 10 mm by 10 mm body accommodates two channels and their associated external line-network interfaces. Designers must observe the specified pin functions, bypass-capacitor requirements, and line-network component values in the manufacturer datasheet. Typical uses include two-line analog phone adapters, voice-over-POTS gateways, digital subscriber line terminal equipment, PBX interface cards, and embedded voice systems. Two integrated channels make the device especially suitable where board area is constrained and each subscriber line requires independent voice processing. A 3.3 V-oriented system can use the device when its interface levels and external circuitry are compatible, while a 5 V-oriented design has a directly listed supply option. The broad -40 °C to +85 °C range also supports industrial and telecommunications temperature requirements. The principal design consideration is the high-voltage telephone-line environment. The SLIC interface must be paired with correctly rated protection, isolation, and line-network components, and the 65 Vrms internal ringing capability does not remove the need for external overvoltage protection. Follow the manufacturer datasheet for BORSCHT-related implementation, power-supply sequencing, grounding, and test-access requirements. Confirm that the chosen protection network preserves the intended line impedance and ringing behavior. This product record combines the exact ordering information, package identity, channel configuration, supply options, ringing capability, interface types, temperature range, and application context needed for initial design review. It also distinguishes the available family-level ordering variants and identifies where additional electrical, pin-level, lifecycle, and qualification details must be confirmed with the manufacturer datasheet before schematic release or production procurement.
SI3220-GQ - Dual SLIC/CODEC 64-TQFP | Skyworks Solutions
The Skyworks Solutions Inc. SI3220-GQ is a dual-channel Subscriber Line Interface Concept and codec integrated circuit with 3.3 V and 5 V supply operation, 65 mA supply current, and a 64-TQFP package measuring 10 mm by 10 mm. It combines two analog telephone-line channels, voice codecs, line diagnostics, and internal balanced ringing up to 65 Vrms in one device. A Subscriber Line Interface Concept, or SLIC, is the analog front end of a telephone line. It replaces discrete circuits for line sensing, ring detection, codec control, voice conversion, and subscriber-line supervision. The SI3220-GQ combines SLIC and codec functions, placing two complete channel interfaces within the wider category of telecom interface ICs, communication semiconductors, and integrated voice-access systems. The device performs the BORSCHT functions required for analog telephone-line operation: battery feed, overvoltage protection, ring supervision, codec signaling, hybrid control, and test access. Its internal balanced ringing reaches 65 Vrms, removing the need for a separate external balanced-ringer circuit in supported designs. Internal diagnostics provide line-condition information that can simplify fault detection and subscriber-line testing. The SI3220-GQ accepts GCI, PCM, and SPI interfaces, allowing it to connect with a digital communications processor or other voice-processing controller. These digital interfaces place the device between the analog subscriber line and the system’s PCM processing fabric. Its low-voltage CMOS implementation supports both 3.3 V and 5 V environments, while low standby power is important in continuously connected voice-access equipment. Typical uses include two-channel voice cards, digital PBX line cards, Voice over IP terminal adapters, analog telephone interfaces, central-office equipment, and other subscriber-line access systems. It is particularly suitable when both phone lines and voice-codec functions must fit into a compact 10 mm by 10 mm package without separate ringing generation. Designers should preserve adequate line-driver and ringing margins, follow the manufacturer’s external component and layout guidance, and validate the complete telephone interface against the intended application. The 941 mW listed power value and 65 mA supply current require attention to supply routing, thermal performance, and bypass-capacitor placement during multi-channel board design. This product data combines the SI3220-GQ’s channel configuration, interface types, power characteristics, ringing capability, package details, and verified ordering alternatives with engineering guidance for telecom line-card implementation. It also distinguishes confirmed package-compatible options from replacements that would require functional and board-level requalification.