Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
SI3220-KQ - Dual-Channel SLIC/Codec | Skyworks Solutions
Skyworks Solutions Inc. SI3220-KQ is a dual-channel Subscriber Line Interface Concept and codec integrated circuit with GCI, PCM, and SPI interfaces, a 65 mA supply current rating, and a 64-pin TQFP package measuring 10 mm by 10 mm. It combines two analog telephone-line channels with codec functionality and supports 3.3 V and 5 V supply operation. The device also provides internal balanced ringing up to 65 Vrms and internal diagnostics. A SLIC is the analog front end used to connect a subscriber telephone line to a digital communications system. By integrating the SLIC, codec, line-driver circuitry, ringing generation, and diagnostics, the SI3220-KQ reduces the component count required for dual-channel analog telephone equipment. In the component hierarchy, it is a telecom interface IC, a line-management IC, and a programmable CMOS SLIC/codec. The device performs the BORSCHT line functions and is identified for applications supporting lines up to 18 kft. Its interfaces support GCI, PCM, and SPI connectivity, allowing it to operate within digital line-card or voice-processing architectures. The internal balanced ringer reaches 65 Vrms, while internal diagnostics support board-level testing of the telephone interface. Its 65 mA supply-current rating and 941 mW listed power figure should be checked against the final rail topology and operating loads. The SI3220/Si3225 family uses programmable low-voltage CMOS circuitry to combine subscriber-line interface and codec functions in accordance with LSSGR, ITU, and ETSI specifications. This integration can simplify the voice path, reduce external glue logic, and shorten development time for dual-channel analog telephone adapters, voice-over-IP terminal equipment, and embedded voice gateways. Typical uses include dual-channel voice gateways, analog telephone line adapters, digital PBX line cards, embedded voice servers, and telecom access equipment. The SI3220-KQ is particularly relevant when one board must support two subscriber lines and when internal ringing and diagnostics can reduce external circuitry. Design carefully around the 64-pin TQFP footprint, exposed analog supply connections, line-interface protection, and the high-voltage ringing path. Use the manufacturer reference design and datasheet application circuit for component values and layout because line-interface networks and protection arrangements are tightly coupled to PCB routing and creepage requirements. This product record combines the part-specific electrical data, package information, interface options, application guidance, and engineering trade-offs needed to evaluate the SI3220-KQ for a dual-channel analog telephone design.
SI3225-BQ Dual-Channel SLIC/CODEC | Silicon Laboratories
The Silicon Laboratories SI3225-BQ is a dual-channel, low-voltage CMOS Subscriber Line Interface Circuit and codec integrated into one 64-pin TQFP device. It supports 3.3 V and 5 V supply operation, has two analog telephone channels, and uses PCM, SPI, and GCI interfaces. The SI3225-BQ provides a complete dual-channel analog telephone interface for connected voice systems and is associated with LSSGR, ITU, and ETSI telephone-interface requirements. A SLIC is the analog front end of a voice subscriber line, while a CODEC converts between analog voice signals and digital PCM data. The SI3225 family combines these functions into a single CMOS IC, reducing the number of discrete telephone-interface components required by a central office, voice gateway, line card, or access-equipment design. Its dual-channel architecture allows one physical device to service two subscriber lines while sharing control, clock, and power circuitry. The SI3225-BQ supports both 3.3 V and 5 V supply configurations and has a listed maximum supply current of 65 mA. Its operating temperature range is -40°C to 85°C, with a listed maximum power dissipation of 941 mW. These ratings make the device appropriate for industrial and communications equipment that must operate from a controlled 3.3 V or 5 V system rail. The 64-pin TQFP package also provides a standardized surface-mount format for high-density line-card designs. Programmable CMOS integration gives the device a defined role in a telephone-line interface rather than a general-purpose signal path. The SI3225 family performs the BORSCHT line functions, supports external bulk ringer operation, and is intended for line lengths up to 18 kft. Its integrated SLIC and codec architecture simplifies the relationship between the physical analog line and the host PCM or GCI data interface, while internal control supports predictable telephone-network behavior. Typical applications include two-channel analog telephone line cards, voice-over-IP access equipment, central-office line interfaces, digital loopback and line-testing systems, and embedded voice gateways. In each design, the host processor must configure the device and exchange PCM traffic through a supported serial interface. The device is most suitable where two independent analog lines, digital voice conversion, and compact surface-mount integration are required in the same subsystem. Design attention should focus on the 3.3 V or 5 V supply implementation, analog telephone-line routing, external bulk-ringer support, and the host interface configuration. Keep sensitive analog and line-driver traces away from high-current switching paths, follow the package and reference-design layout guidance, and verify thermal performance against the 941 mW maximum rating under worst-case line activity. Firmware and line-card validation must also confirm BORSCHT and network requirements for the intended deployment. This product page combines the SI3225-BQ family specifications, interface and application context, verified source links, and engineering-focused design considerations. It also distinguishes temperature-ordering alternatives from functional replacements so procurement and design teams can assess compatibility without treating merely similar codecs as true drop-in devices.
SI3225-FQ Dual-Channel SLIC/Codec IC | Silicon Labs
The Silicon Labs SI3225-FQ is a dual-channel, low-voltage CMOS SLIC/codec integrated circuit for analog telephone-line interfaces, integrating the Subscriber Line Interface Circuit and codec functions in one 64-lead TQFP package. It provides two telephone channels, external ringing support, and internal diagnostics for communications equipment. A SLIC/codec, also called a ProSLIC, combines the line-driving and voice-processing functions required at the network edge. Within the product hierarchy, a SLIC/codec is a telecommunications interface IC, a mixed-signal semiconductor, and a system-level interface between a voice codec and the analog telephone line. The integrated architecture reduces the number of separate analog components while centralizing line supervision, voice processing, and diagnostic functions. The SI3225-FQ supports two independent analog channels in a single device, making it suitable for dual-channel line cards, voice gateways, embedded telephony systems, and customer-premises equipment. Its internal diagnostics assist development and troubleshooting, while external ringing support extends the available line-function capabilities without requiring the same external support arrangement for every design. The SI3225 series is described as a low-voltage CMOS dual ProSLIC platform designed for complete dual-channel analog telephone interfaces. The SI3225 family is associated with LSSGR, ITU, and ETSI interface requirements. Because line-card designs remain sensitive to codec behavior, ringing voltage, impedance, and channel configuration, engineers should preserve the silicon revision, device variant, and firmware configuration associated with the original qualified design. Typical deployments include two-channel analog adapters, voice-over-IP terminal equipment, digital transport cards, and legacy telephone interface equipment being modernized around an existing analog line. Two integrated channels can also reduce routing density and component count when the board must terminate two analog lines in a constrained area, although the line interface still requires the appropriate protection, isolation, and network-side components specified by the system design. During design review, check the SI3225 pin-description table in the manufacturer datasheet before assigning PCB tracks, and validate the external ringing network against the selected line-country configuration. Use the same variant and software configuration for production units, because changing ringing, impedance, or codec behavior may require renewed line-interface qualification even when the package and board footprint remain unchanged.
SI3225-G-FQ - Dual-Channel SLIC/Codec | Silicon Labs
The Silicon Labs SI3225-G-FQ is a dual-channel SLIC/codec telecom interface IC with external ringing support and internal diagnostics, supplied in a 64-QFN package. It supports 3.3 V and 5 V operation, operates from 0°C to 70°C, and consumes 65 mA. The device provides two integrated SLIC circuits and interfaces through GCI, PCM, and SPI. A subscriber line interface circuit, or SLIC, is the analog-side portion of a voice-over-packet or legacy telephone system. It converts between the line signals of a copper subscriber connection and digital voice data. In the IC hierarchy, the SI3225-G-FQ belongs to the interface IC class, combines SLIC and codec functions, and supports telecommunications access equipment such as voice gateways, DSLAMs, and other line-card systems. The device performs all BORSCHT line functions, including battery, overvoltage, ringing, seizure, codec, hook, and tip-and-ring operations. Its dual-channel architecture consolidates two subscriber lines into one integrated interface. Internal balanced and unbalanced ringing is supported, while the SI3225-specific external bulk-ringer support provides flexibility for ringing-generator arrangements. Through its GCI, PCM, and SPI interfaces, the SI3225-G-FQ connects a line-card controller to two analog subscriber lines. The 65 mA supply-current specification, 3.3 V and 5 V supply options, and stated 941 mW power figure make the interface suitable for conventional telecom line-card voltage rails. The commercial 0°C to 70°C temperature range targets indoor or temperature-controlled network equipment rather than harsh automotive or outdoor environments. Typical uses include voice gateways, digital subscriber line access multiplexers, integrated access devices, central-office line cards, and other dual-line voice-processing systems. Two channels per package reduce component count when the board architecture requires multiple subscriber terminations, while software-configurable line functions simplify feature implementation across different ringing and supervision requirements. Layout should keep analog line connections away from high-speed digital signals, while following the manufacturer’s reference layout for bypass capacitors and grounding. Because the device handles high-voltage and high-current line-side conditions, protection, insulation, and creepage requirements must be evaluated at the board and connector level rather than inferred solely from the IC specifications. This page brings together the device’s core electrical specifications, functional characteristics, application guidance, and technically comparable family members. It also identifies where package, pin-level, and lifecycle details require confirmation with the manufacturer or the component datasheet before schematic release or production qualification.
SI3225-G-GQ Dual-Channel SLIC/Codec | Silicon Labs
The Silicon Labs SI3225-G-GQ is a dual-channel SLIC and codec integrated circuit designed for analog telephone-line interfaces, with two line circuits, 3.3 V and 5 V supply operation, GCI, PCM, and SPI interfaces, and a 64-pin TQFP package. It provides external bulk-ringer support, internal diagnostics, and BORSCHT line functions for subscriber-line access equipment. A SLIC, or Subscriber Line Interface Circuit, is the analog front end that connects a telephone line to a digital voice processor. It performs line-state monitoring, hook detection, ring detection, impedance control, DC feed, and overvoltage protection. In a ProSLIC architecture, the SLIC and voice codec are combined to reduce external components while providing a complete dual-channel line interface for central-office equipment, Voice over Packet equipment, and legacy telephone adapters. The SI3225-G-GQ supports two circuits and is specified for both 3.3 V and 5 V supply operation. Its reported 65 mA supply current supports low-power line-interface designs. The device also implements the BORSCHT functions used for off-hook and on-hook line supervision. External bulk-ringer support distinguishes this device from SLIC variants that generate ringing internally. The GCI interface supports direct connection to a DSP, while PCM and SPI interfaces provide additional digital connectivity options. Internal diagnostics assist development and production testing by helping identify line-interface operating conditions. The 64-TQFP package provides 64 external connections for two complete analog channels and their associated digital control, power, and interface signals. Typical uses include central-office line-card assemblies, digital subscriber line equipment, Voice over IP media gateways, embedded telephony controllers, and multi-channel analog telephone adapters. The dual-channel architecture is particularly useful when the surrounding system must handle two subscriber lines while maintaining a common digital backplane and control interface. Layout should prioritize short analog line paths, proper return connections, and compliant isolation or protection networks. Use the manufacturer's pin-description table, application schematic, and layout guidance when assigning tracks because the analog line pins are sensitive to parasitic capacitance, surge transients, and ground-current coupling. Decoupling and protection components should follow the recommended values and placement shown in the manufacturer documentation.
SI3225-KQ - Dual-Channel SLIC/Codec TQFP-64 | Silicon Laboratories
The Silicon Laboratories SI3225-KQ is a dual-channel SLIC/codec telecom line interface IC operating from a 3.3 V or 5 V supply, with an external bulk-ringer support feature and internal diagnostics. It is packaged in a 64-pin thin quad flat package (TQFP) and implements the high-voltage line functions required by analog telephone interfaces. The device contains two line circuits and supports GCI, PCM, and SPI interfaces according to its published specifications. A SLIC/codec is an integrated analog telephone line interface that combines the subscriber-line termination and codec functions required between a telephone network and digital voice equipment. In the hierarchy, a SLIC/codec belongs to the broader category of telecom interface ICs, combines analog line-interface and codec functions in one semiconductor, and serves as the bridge between external telephone-line circuitry and a digital voice system. The SI3225 family is specifically positioned for dual-channel analog telephone interfaces. Key characteristics include two line circuits, a 65 mA supply current rating, operation from either 3.3 V or 5 V, and a 941 mW power rating. The SI3225 supports external bulk-ringer circuitry, while the related Si3200 series also addresses ringing functions. According to the family documentation, the Si3200 linefeed interface family performs all high-voltage functions and can operate from 3.3 V, 5 V, single-battery, or dual-battery supplies, depending on the device and external circuit configuration. The SI3225 integrates both SLIC and codec functionality into a single IC. Its published interface options include GCI, PCM, and SPI, providing selectable pathways for connecting the device to a voice-processing system. The two-circuit architecture supports dual-channel line-card designs while reducing the number of separate analog-interface devices required. Internal diagnostics add observability for system troubleshooting, and the external bulk-ringer support broadens the available linepower design options. Typical uses include analog telephone adapters, voice-over-IP line interfaces, customer-premises equipment, digital PBX line cards, voice gateways, and dual-channel VoIP terminal designs. It is particularly relevant where a compact two-line interface is required and external protection, transformers, ringing, and line-interface networks can be implemented around the IC. System design requires careful separation between low-voltage digital circuitry and telephone-line high-voltage functions. Review the manufacturer pin-description table and recommended external networks before assigning nets. The 0 °C to 70 °C operating range is suitable for commercial-temperature equipment, but it requires confirmation against the enclosure temperature and applicable system qualification requirements. This product record combines the verified electrical and package characteristics, interface options, functional family information, and application guidance for the SI3225-KQ. It also identifies the limits of current cross-reference results and distinguishes a genuine pin-compatible replacement from a merely similar telecom interface device.
SI3226-E-FQ - Dual ProSLIC Telecom Interface | Skyworks Solutions
The Skyworks Solutions SI3226-E-FQ is a dual-channel Subscriber Line Interface Concept and CODEC integrated circuit designed for two-channel foreign exchange station telephony interfaces. It operates from a single 3.3 V supply and is packaged in a 64-TQFP package measuring 10 mm by 10 mm. The device combines two complete analog telephone interfaces with digital PCM, SPI, or GCI bus connectivity, making it suitable for voice-over-IP equipment, analog telephone adapters, digital loop carriers, and other subscriber-line access systems. The SI3226-E-FQ belongs to the ProSLIC family of integrated voice and line-interface circuits. A Subscriber Line Interface Concept, or SLIC, provides the analog termination and control functions required to connect a telephone line to a digital voice system. In combination with a linefeed interface circuit, the SI3226-E-FQ can implement a complete two-channel analog telephone interface while operating from a single 3.3 V supply. This integration reduces the number of external interface functions required in a voice-access design. Key documented characteristics include two integrated SLIC channels, single-supply operation at 3.3 V, support for PCM, SPI, or GCI digital interfaces, and a 64-TQFP package with a 10 mm by 10 mm body. The device is identified as RoHS compliant and uses a PQFP/TQFP-style 64-pin package. Its architecture is intended for telecommunications equipment where a compact, integrated two-channel subscriber-line interface is preferred over a collection of separate analog and codec functions. The SI3226x family is described by the manufacturer as implementing two complete FXS telephony interfaces in one package. That architecture is particularly useful when a system must support two analog phone lines while exchanging voice data with a host processor or digital transport device. The host-side digital interface handles control and PCM traffic, while the analog side implements the subscriber-line termination functions required for voice service. Typical telecom applications include Voice over IP endpoint boards, analog telephone gateways, digital loop carrier equipment, embedded voice systems, and customer-premises telephony products. The 3.3 V supply requirement simplifies power architecture compared with designs requiring separate higher-voltage line-interface rails. The 64-TQFP footprint is mechanically substantial for a high-pin-count mixed-signal device but remains compatible with conventional surface-mount PCB assembly. When designing around the SI3226-E-FQ, preserve the manufacturer’s recommended line-interface topology and separate the sensitive analog line side from digital clocks and switching circuitry. Confirm external component values, termination requirements, digital-interface timing, and thermal performance against the manufacturer’s current datasheet and reference design before release to production.
SI3226-E-GQ - Dual-Channel 3.3V ProSLIC | Skyworks Solutions
Skyworks Solutions SI3226-E-GQ is a dual-channel ProSLIC telecom interface IC that integrates two complete foreign-exchange station telephony interfaces into one 64-pin TQFP package. It operates from a 3.3 V supply and combines SLIC, CODEC, and dual DC-DC controller functionality for subscriber-line interface circuits. Each channel supports the signal conversion and line-driver functions required between a digital voice system and analog telephone lines. A subscriber-line interface circuit, commonly called a SLIC, terminates an analog telephone line, applies the appropriate DC line voltage and current, and converts the analog voice signal into a digital PCM stream. The CODEC section performs the complementary digital-to-analog and analog-to-digital conversion. Integrating these functions into one device reduces the number of external line-interface components, simplifies board layout, and helps designers create compact, consistent two-channel voice-processing modules. The SI3226-E-GQ provides two complete FXS telephony channels, 3.3 V operation, and interfaces identified as GCI, PCM, and SPI. Its dual DC-DC controllers support the power-conversion functions associated with two line channels. The 64-TQFP package provides the physical interface used by the Si3226x Single-Chip Dual ProSLIC family. The architecture is intended for low-voltage CMOS telephony equipment requiring consolidated SLIC and CODEC functionality. The 3.3 V supply requirement suits equipment designed around modern low-voltage digital logic. Designers must follow the manufacturer's recommendations for bypass capacitors, clocking, line-interface components, PCB grounding, and exposed-pad or thermal management where applicable. Because the device integrates sensitive analog line functions with digital control logic, layout quality can affect signal integrity, return noise, and system compliance. Follow the reference schematic and component values in the manufacturer datasheet rather than deriving them solely from the catalog description. Typical uses include Voice over IP endpoint hardware, digital telephone exchanges, voice gateways, customer-premises equipment, line-card modules, embedded telephony controllers, and dual-channel access equipment. In a Voice over IP terminal, the SI3226-E-GQ can handle the analog line termination and PCM voice conversion while the system processor manages packetization and call control. In access equipment, the same dual-channel organization supports two subscriber lines per device and can simplify channel-density planning. The principal engineering trade-off is integration versus board flexibility. A combined SLIC, CODEC, and DC-DC controller reduces external circuitry and board area, but the design remains tightly dependent on correct external component selection and layout. Confirm loop current, line impedance, hook-state behavior, tone generation, clock requirements, and power sequencing against the exact datasheet revision before production release. This page consolidates the key SI3226-E-GQ specifications, package information, drop-in replacement evidence, comparison criteria, and practical integration guidance. It also identifies which parameters must be checked against the manufacturer datasheet before layout or production decisions are finalized.
SI3227-E-FQ - Dual-Channel 3.3V SLIC | Silicon Labs
The Silicon Labs SI3227-E-FQ is a dual-channel subscriber line interface circuit, or SLIC, designed for 3.3 V voice-line systems and packaged in a 64-pin TQFP. It provides two interface channels, 60 dB dynamic gain performance, and approximately 45 mA supply current. The device supports GCI, PCM, and SPI interfaces, providing a flexible interface between a digital voice system and analog telephone lines. A SLIC is an integrated analog-front-end circuit used within subscriber-line access equipment, voice gateways, central-office terminals, and digital telephone systems. In the hierarchy of semiconductor functions, a SLIC belongs to the interface IC class and connects digital switching or codec circuitry to the physical telephone network. It integrates line-driver, receiver, ringing, impedance, and supervision functions that otherwise require many discrete analog components. The SI3227-E-FQ performs the BORSCHT line functions and supports internal balanced or unbalanced ringing. Its two-channel architecture reduces component count and board area in designs requiring multiple subscriber lines. Software-programmable parameters provide a practical way to configure gain, impedance, and line behavior for different loop lengths and network conditions. The 3.3 V supply operation also aligns the device with modern low-power digital voice architectures. According to the Silicon Labs datasheet, the device exposes GCI, PCM, and SPI interface choices and operates from a 3.3 V supply. The listed 60 dB figure identifies the channel performance class, while the approximately 45 mA figure provides a baseline for power budgeting. Because the SI3227-E-FQ also includes dual DC-DC controller capability in this family, it can support line-side power architectures, although the exact external power configuration must follow the manufacturer application guidance. Typical applications include voice-over-IP line-card interfaces, digital subscriber line access equipment, central-office line cards, voice gateways, and short- or long-loop analog telephone interfaces. The two integrated channels are particularly useful when the host processor requires several subscriber-line functions but board space is constrained. For a new layout, place the SI3227-E-FQ close to the protected line interface and keep high-voltage telephone-network paths separate from low-level digital signals. Validate surge protection, transformer or external filtering, line impedance, and ringing behavior against the applicable country-specific network requirements before production release. This product page combines the confirmed interface and electrical characteristics, package information, sourcing guidance, and practical replacement assessment for engineers designing or maintaining dual-channel voice-line interface equipment.
SI3227-E-GQ - Dual-Channel SLIC/CODEC, 3.3V, 64-TQFP
The Silicon Labs SI3227-E-GQ is a dual-channel wideband SLIC/CODEC for telecom line-interface designs, integrating two line-driver circuits, GCI, PCM, and SPI interfaces, dual DC-DC controllers, and 64 line terminations in a 64-pin TQFP package. It operates from a 3.3 V supply and is specified for 45 mA operation with a 60 dB gain-related parameter, making it suitable for voice-over-IP terminals, embedded gateways, and digital subscriber line equipment. A SLIC, or Subscriber Line Interface Circuit, is the analog-facing section of a telephone line interface. It converts between a line-referenced analog voice signal and a digital PCM stream, while a companion CODEC handles signal conversion and voice processing. In the broader semiconductor hierarchy, the SI3227-E-GQ belongs to the interface IC family and then to the telecommunications interface category, combining analog line access, digital logic, and power-conversion control in one device. Key features include two line circuits, 64 terminations, a 3.3 V operating supply, and support for GCI, PCM, and SPI interfaces. The integrated dual DC-DC controllers reduce the number of separate power-management components required in a line-card design. Its 64-pin TQFP package provides enough pin count for two complete channels and their associated control, interface, biasing, and supply connections, while supporting standard surface-mount assembly methods. The device is intended for telecom access equipment where a compact two-channel solution offers a better channel-density tradeoff than discrete SLIC and codec arrangements. Split supply rails created by the internal DC-DC controllers can help separate sensitive analog and digital functions, although component selection and layout remain the responsibility of the system designer. The SI3227-E-GQ also supports lead-free assembly according to its distributor listing. Typical uses include Voice-over-IP endpoint hardware, analog terminal adapters, digital line-card equipment, embedded telephony controllers, and industrial voice gateways. Two integrated channels allow one package to serve both sides of a two-line terminal or a single line pair on a multi-port access board, reducing board area when compared with two separate single-channel devices. The primary design trade-off is channel integration versus flexibility. Combining two SLIC channels, codec functions, digital interfaces, and DC-DC control simplifies the bill of materials, but the layout must carefully separate line-referenced analog routing from high-speed digital signals and sensitive supply nodes. Confirm absolute maximum ratings, line-state impedance requirements, and interface timing against the manufacturer datasheet before releasing a production layout. This page organizes the device specifications, pin-compatible family options, application guidance, and design considerations into one engineering reference. It also identifies the electrical and mechanical details that should be checked during PCB bring-up and production qualification.
SI3230-E-FT Single-Channel SLIC with DC-DC Converter | Skyworks
The Skyworks Solutions SI3230-E-FT is a single-channel, low-voltage CMOS ProSLIC that combines a Subscriber Line Interface Circuit with DTMF detection and generation functions, an external-codec interface, and a BJT/inductor DC-DC converter. It operates from a 3.13 V to 5.25 V supply, draws 88 mA, and is rated at 700 mW, making it suited to compact analog telephone and legacy voice endpoint designs. A Subscriber Line Interface Circuit, or SLIC, is the analog front-end category that connects a telephone line to a digital voice processor. In the system hierarchy, a SLIC is a telecom interface IC that performs line driving, line sensing, ring-voltage generation, and DTMF handling. The SI3230 ProSLIC places these functions into a single low-voltage CMOS device while using an external codec for the voice-processing path. Key features include software-programmable internal balanced ringing up to 90 VPK, support for 5 REN at 4 kft or 3 REN at 8 kft, an integrated battery supply, a DTMF decoder, and a SPI interface for configuration and control. The BJT/inductor DC-DC converter provides the elevated line-side biasing required by analog telephone interfaces while the low-voltage core remains compatible with 3.13 V to 5.25 V system rails. The SI3230-E-FT is designed for compact analog telephone interfaces when connected to an external codec. Its single-channel architecture suits one-line adapters, analog phones, terminal adapters, small PBX peripheral cards, and legacy voice gateways. The 90 VPK balanced ringing capability allows one device to generate the line voltage required by conventional analog handsets without a separate discrete ringer circuit. When designing the line-side network, account for the relationship between REN, loop length, and ringing voltage. The published ringing limits of 5 REN at 4 kft and 3 REN at 8 kft mean that a long loop reduces the permissible load. External protection, filtering, and the line-interface network still require attention because the SLIC controls line-side generation but does not remove the need for overvoltage and surge protection. This page combines the device functions, published operating limits, sourcing information, application fit, and verified manufacturer documentation in one engineering reference. It also distinguishes the functional role of the ProSLIC from that of a codec, a host-side SIP interface, or a discrete DTMF transceiver so that board designers can select the correct component for each block of a legacy voice design.
SI3230-KT - Programmable CMOS SLIC with Ringing | Skyworks
Skyworks Solutions Inc. SI3230-KT is a single-channel, programmable CMOS subscriber line interface circuit with integrated balanced ringing and battery-voltage generation. The device supports internal ringing up to 90 VPK, five REN operation at 4 kft, three REN operation at 8 kft, DTMF generation and decoding, and a software-programmable codec interface. It is intended for 3.13 V to 5.25 V telecommunications equipment and is offered in a surface-mount 38-pin package. A subscriber line interface circuit, or SLIC, is the analog line-side component of a voice-over-packet or legacy telephone system. It connects the telephone line to a digital voice processor, supervises the line state, generates dial and ring signals, and helps establish the DC line voltage required by conventional handsets. Within the communications hierarchy, the SI3230-KT is a ProSLIC integrated circuit that combines line-interface functions with programmable ringing and battery supply generation rather than relying on a large collection of discrete telephone-line components. The main advantages of the SI3230-KT are integration and configuration flexibility. Its software-programmable internal ringing generator supports balanced ring voltages as high as 90 VPK, while the integrated battery supply provides dynamic line-voltage generation. Software control also enables DTMF signaling and codec-interface adjustment, allowing one hardware design to support multiple ringing and line-state requirements. The codec interface integrates the SLIC with a companion digital voice processor without requiring a separate physical telephone line for every configuration. The SI3230-KT includes a BJT/inductor DC-DC converter for the battery supply, as described in the manufacturer documentation. This converter supports the elevated DC and ringing voltages required by analog subscriber lines. Because the converter, ringing generator, battery supply, and signaling logic share one integrated package, the design must account for both analog line quality and the switching energy associated with generating ring voltage. Component selection for the external inductor and energy-storage network should follow the reference configuration and required ringing cadence in the datasheet. Typical applications include Voice over IP endpoint designs, digital subscriber line equipment, analog terminal adapters, voice gateways, embedded telephony controllers, and centralized telephone line cards. The device is particularly suitable when a compact single-channel solution is needed for line supervision, hook detection, DTMF handling, ringing generation, and codec interfacing. In multichannel equipment, several SI3230-KT devices may be arranged around a common voice processor, subject to channel-to-channel isolation, thermal, and routing requirements. Designers should preserve the separation between the line-side and codec-side circuitry, use the recommended ringing and battery-supply external components, and route sensitive analog and high-voltage ring-node connections carefully. The 3.13 V to 5.25 V supply requirement and approximately 88 mA supply current must be accommodated by the host power supply. Because the package exposes high-voltage line functions, board cleanliness, insulation spacing, and protection strategy are as important as low-noise digital layout. This product page combines the principal line-interface capabilities, package constraints, sourcing guidance, and design considerations needed to evaluate the SI3230-KT. It also distinguishes documented device features from parameters that require confirmation against the latest manufacturer datasheet, helping engineers assess it for telecom and embedded voice applications without changing the PCB footprint during early design review.
SI3232-BQ - Dual-Channel Programmable CMOS SLIC | Skyworks
Skyworks Solutions Inc. SI3232-BQ is a low-voltage CMOS subscriber line interface circuit, or SLIC, with a dual-channel architecture and fully software-programmable analog telephone-interface functions for customer premise equipment applications. The verified product information identifies the device as a 64-pin TQFP package, although electrical ratings, temperature limits, clock requirements, and detailed pin assignments were not included in the supplied records. A SLIC is an integrated telephone-interface circuit that belongs to the broader telecommunications interface IC category. It provides the analog line-facing functions required when equipment connects to a telephone network, while allowing switching, supervision, and line-state behavior to be managed by software. In a dual-channel implementation, two analog line interfaces can be controlled from one programmable device, reducing component count compared with separate single-channel solutions. The SI3232's defining verified feature is full software programmability. This allows a customer premise equipment designer to configure line behavior through associated control software instead of relying entirely on fixed hardware settings. Dual-channel integration is particularly useful where two telephone lines must be handled within a compact endpoint, gateway, voice terminal, or analog line-card assembly. The specific programmable functions, register map, and host interface are not present in the supplied snippets. As a low-voltage CMOS IC, the SI3232 combines its analog telephone interface and digital control functions on one monolithic device. CMOS construction is broadly used for low-power integrated circuits because it can support dense digital logic at comparatively low supply voltages, although an exact operating-voltage range cannot be asserted from the supplied data. The 64-TQFP package provides a substantial pin count for two channels, line-state sensing, control connections, analog interfaces, and power or ground assignments. Typical applications include analog telephone adapters, voice-over-IP gateways, customer premise equipment, small telephone line cards, and other dual-line endpoints that require programmable analog line interfacing. For these systems, integration can simplify board partitioning and provide coordinated control of both channels. Designers must still verify line impedance, DC feed characteristics, ring-voltage requirements, codec connections, protection strategy, and regional regulatory behavior against the complete manufacturer documentation. The principal design consideration is that a SLIC is a specialized line-facing device rather than a general-purpose amplifier or codec. Its analog inputs and outputs must be paired with appropriate protection, filtering, routing, and layout measures, while its digital control interface must match the host processor and firmware architecture. Board design should preserve the pin assignments, grounding strategy, and decoupling recommendations contained in the complete SI3232 documentation. This page consolidates the verified product identity, package information, source links, and application context for SI3232-BQ while clearly separating verified facts from unavailable electrical data. The referenced datasheet and product listings should be used to confirm the complete electrical limits, pinout, lifecycle status, current price, and availability before committing a production design.
SI3232-FQ - Dual-Channel 3.3V ISDN SLIC | Silicon Labs
Silicon Labs SI3232-FQ is a dual-channel, fully programmable CMOS Subscriber Line Interface Circuit (SLIC) with a 3.13 V to 3.47 V supply range, 28 mA operating current, and a 64-TQFP 10 mm × 10 mm package. The device integrates balanced ringing up to 65 Vrms and is designed for customer-premise equipment, including ISDN and analog telephone interfaces. Its low-voltage CMOS implementation supports two subscriber lines while limiting standby power to less than 65 mW per channel. A Subscriber Line Interface Circuit, or SLIC, is an integrated-circuit category within analog and telecom interface ICs. It connects a telephone line to a digital or voice-processing system, providing line supervision, DC feed, ring generation, caller-status signaling, and the analog termination required for voice-band operation. In the electronics hierarchy, the SI3232-FQ is a dual-channel SLIC, a telecom interface IC, and ultimately a semiconductor designed for customer-premise telephony equipment. Key features include two integrated analog channels, software-programmable operation, internal balanced ringing rated to 65 Vrms, and low standby consumption below 65 mW per channel. The 3.3 V supply operation is suitable for modern embedded voice systems, while the 28 mA operating current helps control total board-level consumption. Its 64-TQFP package provides a compact surface-mount footprint for CPE designs requiring two telephone interfaces. The SI3232-FQ uses a low-voltage CMOS architecture and combines line-interface functions that would otherwise require multiple discrete or integrated circuits. The -FQ ordering code identifies the lead-free 64-TQFP package associated with a 10 mm × 10 mm body. Because this is a high-voltage telephone-interface device, correct isolation, protection, component spacing, and board-layout practices remain essential even though its logic supply is only 3.3 V. Typical uses include ISDN terminal adapters, VoIP phones, voice gateways, customer-premise analog phone adapters, small-business telephone systems, and embedded telephony equipment. In each case, the two channels can serve separate subscriber lines while software control configures line behavior and monitoring functions. The device is particularly relevant where a compact, integrated SLIC is preferred over discrete line-driver circuitry. Designers should not assume that the 3.3 V logic supply is the only voltage present at the line pins. Balanced ringing can reach 65 Vrms, so external protection, insulation coordination, and creepage or clearance planning must satisfy the applicable telephone-interface requirements. Decoupling should be placed close to the supply pins, and the complete line network should be validated under off-hook, on-hook, surge, and ringing conditions. This product record combines verified distributor specifications, source-backed interface characteristics, and design guidance focused on the SI3232-FQ. It also distinguishes the confirmed SI3232-G-FQ cross-reference candidate from unverified alternatives, avoiding unsupported claims about pin-compatible parts while helping engineers evaluate the original dual-channel SLIC for legacy CPE, ISDN, and VoIP designs.
SI3232-KQ - Dual-Channel Programmable SLIC | Silicon Labs
The Silicon Laboratories SI3232-KQ is a low-voltage CMOS subscriber line interface circuit (SLIC) providing two programmable analog telephone channels for customer premise equipment. It operates from a single 3.3 V supply, communicates through a standard SPI digital interface, and is offered in a 64-pin TQFP package. The SI3232 performs the programmable SLIC functions, while the external Si3200 linefeed interface IC performs the associated high-voltage functions. A SLIC is an integrated telephone-interface device that combines programmable analog voice-channel functions with digital control. It belongs to the interface IC hierarchy, connecting a voice codec or system controller to an analog telephone line. The SI3232-KQ targets CPE designs requiring two channels, centralized register configuration, and a compact low-voltage CMOS implementation. The device provides dual-channel SLIC functionality, a 3.3 V single-supply operating requirement, and a standard SPI control interface. These features make it suitable for voice gateways, digital subscriber line equipment, analog telephone adapters, and other multi-channel voice systems. Programmability allows the controller to configure channel behavior through the serial interface instead of requiring separate fixed-function logic for each line. Its architecture separates low-voltage channel processing from high-voltage linefeed functions. According to the supplied Silicon Laboratories datasheet, the SI3232 performs all programmable SLIC functions, whereas the Si3200 performs all high-voltage functions. This division limits high-voltage handling to the dedicated linefeed IC while allowing the SI3232-KQ to operate from 3.3 V CMOS supply rails. Typical applications include two-channel analog telephone interfaces, customer premise equipment, voice-over-packet gateways, and telecom access products that require software-controlled SLIC operation. A system implementation must also account for the external Si3200, external line protection, and the separation between low-voltage logic and high-voltage telephone-line functions. The principal design consideration is system partitioning. The SI3232-KQ should not be treated as a complete standalone line interface: it requires the Si3200 for high-voltage functions, suitable bypass components, careful SPI control, and application-specific protection. Verified pin-level connection and absolute timing limits should be checked against the manufacturer datasheet before layout release. This page consolidates the verified SI3232-KQ product facts, identifies the Si3200 companion device, and separates documented characteristics from parameters that require datasheet confirmation. It also highlights sourcing and replacement constraints that are not resolved by generic SLIC cross-reference results.
SI3233-C-FM - 38-QFN Programmable SLIC | Silicon Labs
The Silicon Labs SI3233-C-FM is a single-channel software-programmable Subscriber Line Interface Codec (SLIC) designed for telecommunications line-card equipment. It provides an SPI interface to a host controller, integrates one telephone-line circuit, and operates from a 3.13 V to 5.25 V supply. The device is packaged in a 38-pin QFN package. Its programmable architecture supports internal balanced ringing up to 90 VPK, DTMF generation, integrated battery supply, and a codec interface for connected voice applications. An SLIC is the analog front-end for a subscriber line. It converts between the voice-band telephone signal and a digital PCM or codec representation, while also handling line supervision, ringing, tone generation, and hook-state functions. In the telecommunications hierarchy, the SI3233-C-FM is a telecommunications interface IC and system-on-chip designed to reduce the component count of a single-channel line-card design. The external Si3201 companion is used with this ProSLIC family in reference applications. Key features include SPI host control, one integrated line circuit, an 88 mA supply current, and software-configurable internal ringing rated to 90 VPK. Ringing capability is specified for 5 REN at 4 kft and 3 REN at 8 kft. The IC also generates DTMF tones and includes a lead-free status, making it suitable for modern subscriber-line and voice-access equipment requiring programmable line functions. The SI3233-C-FM combines analog line-interface functions with host-programmable control. Firmware can configure ringing, tone generation, line supervision, and codec behavior through the SPI interface, allowing one device to serve multiple network requirements. This integration reduces external line-driver circuitry and gives the host processor direct control over subscriber-line signaling. Typical uses include single-channel subscriber line access, voice-over-IP line cards, voice gateways, digital subscriber line equipment, and telephone line test systems. The 38-QFN package supports compact designs, while the 3.13 V to 5.25 V operating range is suitable for regulated 3.3 V and 5 V digital and analog systems. Designers should pay close attention to the high-voltage ringing interface, external protection network, thermal dissipation, and the required companion circuitry. The line-facing pins must be isolated from logic ground according to the application reference design. Decoupling must be placed close to the supply pins, and the PCB layout must account for the exposed thermal pad and the high-voltage transient environment at the subscriber line. This page organizes the SI3233-C-FM technical characteristics, procurement information, application context, and engineering considerations. It also distinguishes documented functionality from parameters that require confirmation against the manufacturer datasheet, helping engineers plan a compliant line-card design more efficiently.
SI3241-D-GQ Quad ProSLIC SLIC/Codec 3.3V 100-eTQFP | Skyworks
The Skyworks Solutions Inc. SI3241-D-GQ is a quad-channel ProSLIC subscriber line interface circuit (SLIC) and codec that integrates four independent voice channels onto a single 3.3 V integrated circuit in a 100-pin eTQFP (14 x 14 mm) package with an exposed thermal pad. It is a programmable CMOS SLIC/codec device whose channels each deliver 63 dB of gain and whose host-side interfaces include GCI, PCM and SPI. A SLIC, or subscriber line interface circuit, is the analog front-end block that sits between a public switched telephone network line and the digital voice equipment behind it. In the hierarchy of telecommunications semiconductors, a SLIC is a voice-access interface IC, a subcategory of interface ICs that converts analog line signals into digital PCM bit streams while also providing DC feed, ring generation, hook detection and loop supervision. A combined SLIC/codec such as the SI3241 merges those analog functions with a digital voice codec so a single device can terminate four analog lines and deliver four channels of compressed or uncompressed voice to a host processor. Key characteristics of this device include four integrated voice channels per package, a 3.3 V supply rail, and multiple host-side serial interfaces, so one IC can replace four discrete line-interface front ends. The silicon is a programmable CMOS design: channel gain, impedance, DC feed and filter behavior are configured through registers rather than external components, which simplifies the analog bill of materials and shortens design-in time for voice gateways, DSL access equipment and VoIP media gateways. Because the same silicon supports both classic PCM and GCI/PCM/SPI transport, the device spans legacy TDM designs as well as modern packet-voice designs. Architecturally, each of the four channels combines a line-side driver and receiver, the voice codec, and the supervision logic behind a common register interface, with a shared digital backplane to the host. The part is offered in a 100-lead eTQFP with a thermally and electrically connected exposed pad, which lowers package thermal resistance and lets the pad be tied to the ground plane on multilayer boards. The exposed pad must be soldered and connected, otherwise both heat dissipation and the device's ground return degrade. Ordering codes such as -D-GQ denote the die revision, grade and tray packaging, and the -R suffix denotes the same die in tape-and-reel form. Typical applications include multi-channel VoIP analog terminal adapters, voice-over-PON and DSL voice gateways, digital loop carrier and line-card designs, PBX trunk interfaces, and industrial voice monitoring equipment where four lines must be digitized per board. Because each channel is register-programmable, the same hardware can be reconfigured in the field for different line impedances and country-specific DC feed requirements, which is a significant advantage over fixed analog front ends. A key design consideration is that the exposed pad and the high line-side drive currents make careful layout mandatory: keep the analog line traces short and isolated from the digital backplane, provide solid decoupling on the 3.3 V rail, and follow the manufacturer's reference layout for the pad connection and the line-side network. A second consideration is that the silicon is mature but still widely supported, so firmware drivers for this ProSLIC family are broadly available. This page consolidates distributor availability, package and ordering-code detail, drop-in ordering options within the SI3241 family, and practical layout and thermal guidance into a single engineering reference that complements, rather than repeats, the manufacturer datasheet.
SI8244BB-C-IS1 - 2-Channel Isolated Class-D Driver
The Silicon Labs SI8244BB-C-IS1 is a two-channel isolated Class-D audio driver with a precision dead-time generator, a 16-SOIC package, and an operating supply range of 4.5 V to 5.5 V. It is designed for isolated high-side and low-side gate-drive arrangements in high-power audio systems, including power stages above 30 W according to the manufacturer family description. An isolated gate driver is an interface and power-management semiconductor that transfers switching-control signals across a galvanic-isolation barrier while driving external MOSFET gates. The SI8244BB family combines two isolated drivers in one package, enabling compact isolated audio power stages, reduced ground-loop risk, and separation between control and power domains. Its high-side and low-side organization suits full-bridge Class-D topologies. The key verified feature set includes PWM input, a high-precision linear programmable dead-time generator, 1 µs dead-time capability, high latchup immunity greater than 100 V/ns, and up to 1500 Vrms output-to-output isolation. The verified operating-temperature range is -40 °C to 125 °C. The device is supplied in a 16-SOIC package, also identified as MS-012AC in distributor documentation. The precision dead-time function helps the designer balance low total harmonic distortion against switching efficiency by controlling the non-overlap interval between MOSFET gate commands. Exact propagation-delay, output-current, supply-current, and channel-polarity values were not supplied in the verified source set, so these parameters are not inferred here. The -IS1R variant is documented as RoHS compliant, but separate C-IS1 environmental declarations were not provided. Typical uses include isolated Class-D audio amplifiers, full-bridge speaker power stages, isolated digital-to-analog audio systems, and industrial audio equipment where control-side and power-side grounds must remain separated. The Si824x family datasheet specifically targets high-power audio applications above 30 W. The driver should be paired with appropriately rated external MOSFETs, gate resistors, isolation components, and a thermal plan based on the final power-stage dissipation. For PCB implementation, preserve the isolation creepage and clearance required by the final working voltages and certification target. Keep high-current gate-drive loops compact, connect each driver output to its corresponding MOSFET gate through the recommended resistor network, and provide local bypassing at the device supply pins. Do not infer a direct replacement from package similarity alone; verify dead-time, propagation delay, UVLO, channel polarity, isolation rating, and output-drive current against the original design. This page combines the verified manufacturer family datasheet, distributor package data, and cross-reference evidence for the SI8244BB-C-IS1. It separates documented facts from unresolved procurement and electrical details, providing a practical basis for Class-D gate-drive design, sourcing review, and footprint-compatible replacement investigation.
SI8244BB-C-IS1R - 2-Channel Isolated Class-D Driver (Tape & Reel)
The Silicon Labs SI8244BB-C-IS1R is a two-channel isolated Class-D audio driver with a precision dead-time generator, a 16-SOIC package, and an operating supply range of 4.5 V to 5.5 V. It is designed for isolated high-side and low-side gate-drive arrangements in high-power audio systems, including power stages above 30 W according to the manufacturer family description. An isolated gate driver is an interface and power-management semiconductor that transfers switching-control signals across a galvanic-isolation barrier while driving external MOSFET gates. The SI8244BB family combines two isolated drivers in one package, enabling compact isolated audio power stages, reduced ground-loop risk, and separation between control and power domains. Its high-side and low-side organization suits full-bridge Class-D topologies. The key verified feature set includes PWM input, a high-precision linear programmable dead-time generator, 1 µs dead-time capability, high latchup immunity greater than 100 V/ns, and up to 1500 Vrms output-to-output isolation. The verified operating-temperature range is -40 °C to 125 °C. The device is supplied in a 16-SOIC package, also identified as MS-012AC in distributor documentation. The precision dead-time function helps the designer balance low total harmonic distortion against switching efficiency by controlling the non-overlap interval between MOSFET gate commands. Exact propagation-delay, output-current, supply-current, and channel-polarity values were not supplied in the verified source set, so these parameters are not inferred here. The -IS1R variant is documented as RoHS compliant, but separate C-IS1 environmental declarations were not provided. Typical uses include isolated Class-D audio amplifiers, full-bridge speaker power stages, isolated digital-to-analog audio systems, and industrial audio equipment where control-side and power-side grounds must remain separated. The Si824x family datasheet specifically targets high-power audio applications above 30 W. The driver should be paired with appropriately rated external MOSFETs, gate resistors, isolation components, and a thermal plan based on the final power-stage dissipation. For PCB implementation, preserve the isolation creepage and clearance required by the final working voltages and certification target. Keep high-current gate-drive loops compact, connect each driver output to its corresponding MOSFET gate through the recommended resistor network, and provide local bypassing at the device supply pins. Do not infer a direct replacement from package similarity alone; verify dead-time, propagation delay, UVLO, channel polarity, isolation rating, and output-drive current against the original design. This page combines the verified manufacturer family datasheet, distributor package data, and cross-reference evidence for the SI8244BB-C-IS1R. It separates documented facts from unresolved procurement and electrical details, providing a practical basis for Class-D gate-drive design, sourcing review, and footprint-compatible replacement investigation.
SI8244CB-D-IS1 - 2-Channel 4A Audio Driver | Skyworks
The Skyworks Solutions SI8244CB-D-IS1 is a dual-channel isolated audio gate driver for Class D amplification, with a 4 A peak output current and a 16-pin SOIC package. According to the available manufacturer and distributor data, it is intended for high-power audio systems above 30 W and supports a maximum supply voltage of 24 V. What is an isolated audio gate driver? An isolated audio gate driver is a specialized interface and power-management IC that transfers gate-control signals while providing galvanic isolation between control circuitry and a power stage. It belongs to the gate-driver family within the broader Class D audio-driver hierarchy, combining signal conditioning, level translation, isolation, and high-current output drive in one package. The SI824x family is designed to support high-fidelity Class D amplification, with the SI8244 variant providing 4.0 A peak output current for driving external MOSFET gate networks. The available data identifies a 2-channel configuration, 2.5 kV isolation capability, and operation with a maximum 24 V supply. The Skyworks product page specifically highlights precise dead-time adjustment as a way to balance total harmonic distortion and system efficiency. Typical applications include high-power stereo audio amplifiers, subwoofer amplifiers, professional audio equipment, home-theater systems, and other isolated gate-drive circuits. Isolation can help reduce ground-reference problems when the audio power stage and control electronics operate at different potentials. The two-channel structure also allows one driver IC to support complementary or multi-channel Class D output stages. Designers should verify the exact input logic levels, propagation delay, quiescent current, enable behavior, isolation ratings, and external MOSFET requirements against the manufacturer datasheet before production. Gate traces must be short and properly terminated, and the power-stage layout must minimize loop area to preserve switching performance and reliability.
SI8244CB-D-IS1R - 2-Channel 4A Audio Driver | Skyworks (Tape & Reel)
The Skyworks Solutions SI8244CB-D-IS1R is a dual-channel isolated audio gate driver for Class D amplification, with a 4 A peak output current and a 16-pin SOIC package. According to the available manufacturer and distributor data, it is intended for high-power audio systems above 30 W and supports a maximum supply voltage of 24 V. What is an isolated audio gate driver? An isolated audio gate driver is a specialized interface and power-management IC that transfers gate-control signals while providing galvanic isolation between control circuitry and a power stage. It belongs to the gate-driver family within the broader Class D audio-driver hierarchy, combining signal conditioning, level translation, isolation, and high-current output drive in one package. The SI824x family is designed to support high-fidelity Class D amplification, with the SI8244 variant providing 4.0 A peak output current for driving external MOSFET gate networks. The available data identifies a 2-channel configuration, 2.5 kV isolation capability, and operation with a maximum 24 V supply. The Skyworks product page specifically highlights precise dead-time adjustment as a way to balance total harmonic distortion and system efficiency. Typical applications include high-power stereo audio amplifiers, subwoofer amplifiers, professional audio equipment, home-theater systems, and other isolated gate-drive circuits. Isolation can help reduce ground-reference problems when the audio power stage and control electronics operate at different potentials. The two-channel structure also allows one driver IC to support complementary or multi-channel Class D output stages. Designers should verify the exact input logic levels, propagation delay, quiescent current, enable behavior, isolation ratings, and external MOSFET requirements against the manufacturer datasheet before production. Gate traces must be short and properly terminated, and the power-stage layout must minimize loop area to preserve switching performance and reliability.
SI8380P-IU - 8-Ch 24V Digital Isolator 2.5kV | Skyworks
The Skyworks Solutions (formerly Silicon Labs) SI8380P-IU is an 8-channel 24 V digital field-input isolator with integrated 2.5 kVRMS safety-rated isolation, housed in a 20-pin SSOP (QSOP) package. It delivers bipolar digital interface support for both sinking and sourcing 24 V inputs at data rates up to 2 Mbps with 250 kbps typical guaranteed throughput and 200 kV/µs common-mode transient immunity (CMTI). The device targets IEC 61131-2 switch types 1, 2, and 3 in PLC and industrial I/O modules. A digital isolator is an integrated circuit that transfers logic signals between two galvanically isolated domains using capacitive, inductive, or optical coupling while blocking DC and low-frequency voltages up to the rated isolation voltage. Isolators sit between the field side (24 V sensors, switches, actuators) and the logic side (microcontroller, SoC) to protect downstream circuitry from transients, ground loops, and fault voltages on the field wiring. Within the broader IC taxonomy, digital isolators belong to interface ICs, which in turn sit under signal conditioning and inter-domain connectivity. Key features of the SI8380P-IU include eight channels in a single package, low 1 mA typical input current per channel, integrated safety-rated isolation eliminating the need for external optocouplers, CMOS-based LED emulator technology enabling bipolar (sinking or sourcing) capability, and no isolated-side VDD required because power is harvested from the input current. The device provides logic-level outputs on the controller side that interface directly with 2.25 V to 5.5 V MCU I/O rails. Architecturally, the SI8380P-IU combines an input-side current-limiting front end, a CMOS-LED emulator that generates an optically-equivalent modulation signal, an integrated isolation barrier using Silicon Labs' proprietary capacitive or transformer coupling, and an output-side demodulator. This topology replaces legacy optocoupler-based designs that required external current-limit resistors, discrete photodiodes, and bulky isolation components, while improving speed, CMTI, and aging behavior. Typical applications include 24 V PLC digital input modules, industrial sensor interfaces (proximity sensors, limit switches, push-buttons), motor-drive digital I/O isolation, building automation input cards, and any system requiring IEC 61131-2 type 1/2/3 input compliance. The wide input voltage range and bipolar capability allow the same part to handle both sourcing (PNP-style) and sinking (NPN-style) field wiring without redesign. When designing with this part, verify that the field-side input current meets the 1 mA typical requirement through proper resistor selection at the input pin. The QSOP-20 footprint is pin-compatible with other Si838x family variants, allowing easy migration to higher channel count or different polarity configurations. Always observe creepage and clearance requirements for the 2.5 kVRMS isolation rating per IEC 60747-17 in the PCB layout. This page synthesizes distributor pricing, drop-in Si838x family alternatives, IEC 61131-2 application context, and PCB layout guidance not consolidated on any single manufacturer or distributor page.
SI8420AD-D-IS - 2-Ch 5kV Digital Isolator, 1Mbps | Skyworks/Silicon Labs
The Skyworks Solutions (formerly Silicon Labs) SI8420AD-D-IS is a general-purpose dual-channel digital isolator rated at 5000 Vrms with a 1 Mbps data rate and 20 kV/us common-mode transient immunity (CMTI), housed in a 16-pin wide-body SOIC (0.295 inch / 7.50 mm width) package. A digital isolator is a semiconductor component which transfers digital signals between two galvanically isolated domains using an on-chip RF carrier or transformer coupling, replacing bulky optocouplers. The SI8420AD-D-IS belongs to the Si84xx family of CMOS digital isolators and sits within the broader isolation IC hierarchy: digital isolator -> signal isolator -> interface IC -> integrated circuit. The wide-body SOIC-16 package provides the 8 mm creepage/clearance required by reinforced insulation standards (UL 1577, IEC 60747-17, CSA 5A) for end-system voltages up to 600 Vrms or 848 Vpk. Key features include 5000 Vrms isolation withstand voltage per UL 1577 for 1 minute, 2 unidirectional channels (1 forward + 1 reverse), 25 kV/us minimum CMTI to suppress fast transients from IGBT/MOSFET switching, 2.7 V to 5.5 V supply range on both sides, and an operating temperature range of -40 C to +125 C. The device draws a low quiescent current on each side and integrates Schmitt-trigger inputs with default high output state (B-side) or default low (A-side) for fail-safe behavior. The Si84xx family uses Skyworks' proprietary RF-coupled isolation architecture with an on-chip CMOS oscillator and differential transformer coupling. This topology delivers higher data-rate, lower power, and tighter channel-to-channel matching than LED-based optocouplers, while eliminating the LED aging and CTR degradation concerns that limit optocoupler lifetime in industrial designs. Typical applications include isolated gate drivers for IGBT/MOSFET half-bridges in motor drives, isolated UART/SPI interfaces in PLCs, isolated analog front ends in medical equipment, and isolated communication links in industrial 24 V systems. The 1 Mbps rate is well matched to I2C, SPI, GPIO and asynchronous serial protocols. When laying out, place decoupling capacitors (typically 0.1 uF) close to each VDD pin, avoid routing high-CMTI traces near the isolation barrier, and respect the 8 mm creepage/clearance requirement across the SOIC-16 wide-body body for reinforced isolation. Designers migrating from optocouplers should verify that the Si84xx default output state matches the application fail-safe condition. This page synthesizes distributor pricing, drop-in Si84xx family alternatives, parametric comparisons and practical layout guidance not found on a single distributor listing.
SI8421AD-D-IS - 5kV 2-Channel Digital Isolator 1Mbps | Silicon Labs
The Silicon Labs SI8421AD-D-IS is a 2-channel general-purpose digital isolator rated at 5000 Vrms withstanding isolation and 20 kV/us minimum common-mode transient immunity (CMTI), housed in a 16-pin wide-body SOIC package (7.5 mm creepage). Each of the two unidirectional isolation channels supports a maximum data rate of 1 Mbps with worst-case propagation delay under 35 ns, and the 'D' option code specifies a default-low fail-safe output state during input power loss. The device operates from a 2.7 V to 5.5 V supply on either side, with independent channel-to-channel ground returns that allow flexible bidirectional signaling across an isolation barrier. A digital isolator is a semiconductor device that transfers logic-level signals across an isolation barrier using on-chip RF-coupled or capacitive-coupled isolation channels instead of optocouplers or transformers. Digital isolators belong to the isolation IC hierarchy: isolator -> interface IC -> signal chain IC -> semiconductor. Compared to legacy optocouplers, CMOS digital isolators offer 10x higher reliability, lower propagation delay, lower power consumption, smaller footprint, and stable parametric performance over temperature and aging. Key features of the SI8421AD-D-IS include Schmitt-trigger inputs for noisy industrial environments, 5 kVrms safety isolation certified by UL, CSA, and VDE, and reinforced insulation rating when used in wide-body SOIC. The device consumes approximately 1.8 mA per channel at 1 Mbps, supports 2.7 V to 5.5 V supply on both VDD1 and VDD2 rails, and operates across the -40 C to +125 C industrial temperature range. The wide-body SOIC-16 package provides 7.5 mm of creepage distance per IEC 60601 / IEC 60747-17 requirements for reinforced insulation. The Si8421 family uses Silicon Labs' proprietary RF-coupled isolation technology, embedding an RF carrier across two capacitive isolation capacitors on each die. This architecture eliminates the LED aging and current-transfer-ratio degradation inherent to optocouplers and achieves typical CMTI performance an order of magnitude above opto-based solutions. The wide-body SOIC package provides the reinforced creepage distance required for 5 kV reinforced insulation in industrial, renewable-energy, and medical systems. Typical applications include isolated SPI/UART interfaces in motor drives, isolated gate-drive signal paths in industrial inverters, isolated data acquisition front-ends, isolated power-supply feedback, and isolated serial communication between MCU and high-voltage subsystems. The 5 kV rating suits 480 Vac industrial bus systems and 600 V solar inverter signal chains where reinforced insulation is mandated. When designing with this device, place 0.1 uF bypass capacitors close to each VDD pin and minimize trace capacitance on the input/output side. The two channels are unidirectional and identically configured; if bidirectional signaling is needed across the same isolation barrier, choose a Si8421 (1 forward + 1 reverse) variant or pair two Si8421AD-D-IS devices in opposing directions. The default-high or default-low output behavior under input power loss must match the system-level fail-safe state. This page synthesizes distributor pricing, parametric drop-in alternatives from the same Si84xx family and cross-brand equivalents, and practical isolation design notes not found in the manufacturer datasheet alone.