Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
TUSB8042RGCR - 4-Port 5 Gbps USB 3.1 Hub | Texas Instruments
The Texas Instruments TUSB8042RGCR is a four-port SuperSpeed USB 3.1 hub controller supporting data rates up to 5.0 Gbps, with USB 2.0 and USB 1.1 compatibility, in a 64-pin VQFN (RGC) package. It is designed to extend multiple USB connections across desktop computers, industrial equipment, test systems, and peripheral-heavy embedded platforms. A USB hub controller is an interface integrated circuit that manages one upstream USB connection and multiple downstream ports. Within the hierarchy of USB interface controllers, it adds device enumeration, port routing, power-management coordination, and traffic arbitration while allowing USB peripherals to share one host controller. The TUSB8042RGCR combines SuperSpeed and legacy USB support in one device, simplifying system design where both high-bandwidth storage and conventional peripherals must coexist. The principal features include four downstream ports, SuperSpeed operation at 5.0 Gbps, and backward compatibility with Full Speed and High Speed USB devices. GPIO, I2C, and SMBus interfaces support configuration and supervisory functions. Per-port power switching and overcurrent detection improve fault isolation when a downstream device faults. The manufacturer specifies a commercial operating range of 0°C to 70°C for the TUSB8042RGCR ordering option. Internally, the controller coordinates traffic between the upstream host-facing port and four downstream USB ports while maintaining independent command, data, and status paths needed for USB connectivity. This integrated hub architecture reduces the number of discrete USB interface and switching elements required in a design. The exposed-pad VQFN construction also supports thermal transfer into a multilayer PCB, an important consideration when several attached devices can drive continuous data activity. Typical uses include external docking stations, laboratory data-acquisition equipment, industrial USB expansion, computer accessories, and embedded systems that need multiple USB connections. In each case, the five-gigabit SuperSpeed path is useful for storage, cameras, and other high-throughput peripherals, while legacy support allows existing USB 1.1 and USB 2.0 devices to operate without separate downstream controllers. Design the board with the exposed pad connected to the ground plane and follow the manufacturer’s recommended decoupling and high-speed layout guidance. Place decoupling capacitance close to supply pins, provide a continuous reference plane beneath the high-speed region, and route differential pairs with matched geometry. Verify power-distribution capacity and overcurrent behavior for the intended downstream-load combination. This page consolidates the manufacturer ordering information, package characteristics, verified source links, compatible same-package options, and practical PCB guidance for engineers evaluating the TUSB8042RGCR as a four-port USB hub controller.
TUSB8042RGCT - 4-Port USB 3.1 Hub | Texas Instruments
The Texas Instruments TUSB8042RGCT is a four-port SuperSpeed USB 3.1 Gen 1 hub controller supporting data rates up to 5.0 Gbps. It is packaged in a 64-pin VQFN package measuring 9 mm by 9 mm and provides GPIO, I2C, and SMBus interfaces for configuration, monitoring, and peripheral connectivity. The controller consolidates one USB host connection into four downstream ports for systems that require expanded USB connectivity without using multiple independent host controllers. A USB hub controller is an interface integrated circuit within the USB interface IC hierarchy. Its role is to manage traffic between an upstream USB host and multiple downstream ports while providing the electrical and protocol functions required for USB SuperSpeed operation. Unlike a passive USB splitter, a hub controller contains active logic for enumerating devices, managing port events, and coordinating data transfers across the hub. The TUSB8042RGCT provides four SuperSpeed downstream ports and a 5.0 Gbps maximum data rate. Its GPIO, I2C, and SMBus interfaces support configuration and control functions beyond basic USB signaling. These interfaces can assist with port-status monitoring, programmable control logic, and system-level management. The manufacturer datasheet also identifies a reference-clock requirement for designs using an external clock source. The clock source requires frequency stability of plus or minus 100 ppm or better. It must also have less than 50 ps absolute peak-to-peak jitter, or less than 25 ps peak-to-peak jitter after applying the USB 3.1 jitter transfer function. These requirements are important because reference-clock instability can reduce margin for eye closure, timing compliance, and reliable enumeration across all four ports. Typical uses include industrial USB equipment, test and measurement systems, peripheral expansion, embedded computing platforms, and docking systems. In these applications, the controller allows one upstream SuperSpeed USB link to serve multiple downstream peripherals while preserving a single controlled hub function. The I2C and SMBus connections also complement USB devices that require configuration or supervisory access outside the USB protocol. PCB implementation should follow the manufacturer’s VQFN land pattern and high-speed layout guidance. The 64-pin VQFN package requires careful thermal-pad connection, short differential routing, and continuous reference planes. Power and ground distribution must also support the simultaneous operation of the upstream port and four downstream SuperSpeed ports without introducing unacceptable signal degradation. This product page combines the exact ordering information, package details, interface capabilities, and clock constraints into an engineering-focused guide. It also distinguishes the confirmed TUSB8042RGCT ordering variant from the limited drop-in alternatives supported by manufacturer and cross-reference information.
TUSB8043RGCR - 4-Port 5Gbps USB 3.1 Hub | Texas Instruments
The Texas Instruments TUSB8043RGCR is a four-port SuperSpeed USB 3.1 hub controller with a maximum data rate of 5.0 Gbps, HID-to-I2C support, and a 64-pin RGC VQFN package measuring 9 x 9 mm. It provides the upstream and downstream interface logic required to manage multiple USB SuperSpeed devices through one host connection. A USB hub controller is a semiconductor that manages traffic between a host USB port and multiple downstream ports. The TUSB8043 belongs to the hierarchy of USB interface controllers, interface ICs, and integrated circuits. Its SuperSpeed capability follows the USB 3.1 Gen1 data-rate ceiling of 5.0 Gbps, while its HID-to-I2C bridge enables configuration information to be transferred between a USB host and an attached I2C EEPROM. The principal features are four downstream hub ports, USB 3.1 Gen1 operation at 5.0 Gbps, USB 1.1 and USB 2.0 backward-compatible interface support, an internal USB HID-to-I2C bridge, and support for programming an attached EEPROM. The commercial TUSB8043RGCR version is specified for an operating-temperature range of 0°C to 70°C and uses a 64-pin RGC package. Technically, the device consolidates hub-control and configuration functions into one controller. The HID interface provides a standardized host-access path, while the I2C interface connects the controller to an external configuration memory device. This architecture reduces the need for separate host-controlled configuration logic and supports designs where hub identification or nonvolatile configuration must be stored in EEPROM. The 9 x 9 mm VQFN package also supports compact desktop, industrial, and embedded USB hub implementations. Typical applications include four-port USB docking stations, industrial USB hubs, embedded host systems, test and measurement equipment, and USB peripheral expansion. The device is particularly suitable when one USB connection must support several downstream peripherals while maintaining a configurable SuperSpeed hub. The associated crystal-selection guidance for USB 2.0 devices is identified by Texas Instruments application note SLLA122. PCB implementation should preserve short high-speed USB traces, provide continuous return-path references, place the crystal and supporting components close to the controller, and follow the manufacturer’s recommended power and decoupling layout. Keep copper away from the exposed-pad region where electrical isolation is required, and use the exposed pad as a thermal and low-inductance ground connection when the package drawing directs it. This page organizes the verified product identity, package, interface, ordering, pricing, and sourcing information for the TUSB8043RGCR and adds application guidance, design considerations, and engineering-oriented comparisons. Use the manufacturer datasheet and pin-description table when assigning all 64 package connections and when validating the final USB, power, EEPROM, and clock implementation.
TUSB8043RGCT - 4-Port USB 3.1 Gen1 Hub Controller | Texas Instruments
The Texas Instruments TUSB8043RGCT is a 4-Port SuperSpeed USB 3.1 Gen1 hub controller supporting 5.0 Gbps signaling on downstream ports, housed in a 64-pin VQFN (RGC) 9x9 mm package. It integrates USB HID to I2C bridging, allowing host-side configuration of an attached EEPROM without an external bridge chip. The device supports full-speed, high-speed, and SuperSpeed USB operation across all four ports. A USB 3.1 hub is a connectivity expansion device that multiplies one upstream USB port into four downstream USB ports while maintaining protocol-aware traffic management. In the hierarchy of USB silicon, the TUSB8043 sits between USB 2.0 hubs (480 Mbps legacy) and USB 3.2 Gen2 (10 Gbps) hubs, serving the dominant consumer, docking-station, and embedded segment where 5 Gbps SuperSpeed is sufficient and power/area efficiency matter. Key features include per-port transaction translators (TTs) for full-/high-speed traffic, USB Battery Charging specification 1.2 support, integrated USB 2.0 PHY and SuperSpeed PHY per port, and configurable I2C/SMBus access through the HID endpoint. The device draws from a single 3.3 V supply rail and uses an external 25 MHz crystal, simplifying board layout. The RGC VQFN package exposes a thermal pad for heat spreading in sealed enclosures. Architecturally, the TUSB8043 implements a multi-RTL pipeline that schedules USB isochronous, interrupt, bulk, and control transfers independently per port, with split transactions across the 5 Gbps SuperSpeed lane for upstream traffic. Its hardware HID-to-I2C bridge maps vendor-specific USB control requests to I2C writes on the firmware-configured address, enabling platform designers to configure downstream peripherals from the host without an additional MCU. Typical applications include Thunderbolt and USB-C docking stations, industrial PCs and factory workstations, monitor bases with multiple USB peripherals, embedded computing platforms, point-of-sale terminals, and USB expansion cards. With USB-IF compliance built into the silicon, the TUSB8043 also powers medical imaging carts and test instrumentation where certified interoperability is mandatory. Designers should remember that downstream port power-enable and current-limit control require external TPS2041B/TPS2051B load switches; the TUSB8043 itself does not source VBUS. The 25 MHz reference must be a fundamental-mode crystal with ±50 ppm tolerance, and DP/DN traces on each downstream port require 90 Ω differential impedance matching to USB-IF compliance masks. This page aggregates distributor pricing, drop-in equivalents, and application-level design guidance drawn from the manufacturer datasheet and field reference designs, going well beyond a single-source product listing.
TUSB8044RGCR - 4-Port 5Gbps USB 3.1 Hub | Texas Instruments
The Texas Instruments TUSB8044RGCR is a 4-port SuperSpeed USB 3.1 hub controller with a maximum data rate of 5.0 Gbps per USB port and USB Billboard support, housed in a 64-pin VQFN RGC package measuring 9 mm by 9 mm. The controller supports 1.1 V and 3.3 V supply rails and is designed for industrial and embedded USB expansion applications. A USB hub controller is an interface integrated circuit that manages one upstream USB connection and multiple downstream ports. Within the semiconductor hierarchy, it belongs to the USB interface controller family, interface IC category, and broader integrated-circuit domain. Its function is to divide an upstream USB data path among connected peripherals while coordinating enumeration, power, status, and configuration across four external SuperSpeed ports. The TUSB8044 provides four 5.0-Gbps SuperSpeed downstream ports and includes USB Billboard capability for presenting device identity and compatibility information. Configuration can be implemented with pin straps for supported functions, one-time-programmable ROM, an I2C EEPROM, or an I2C or SMBus slave interface for programmable PID, VID, port, and PHY configurations. These options support both standardized product identification and customized hub behavior. The device also supports one Alternate mode, according to the Texas Instruments product page. In a system design, the upstream interface connects the hub to a host or another USB controller, while the four downstream ports connect external devices such as storage, peripherals, Ethernet adapters, or industrial interfaces. USB Billboard can make the hub appear as a useful interface to a connected USB-C host when a more appropriate class-specific presentation is unavailable. Typical uses include industrial control panels, medical carts, test and measurement systems, embedded computers, docking stations, and multi-port peripheral hubs. The 9 mm by 9 mm VQFN package supports compact designs, but its 64-pin land pattern requires careful high-speed layout and complete ground-plane treatment. For signal integrity, route all SuperSpeed differential pairs as controlled-impedance, length-matched connections with minimal stubs and continuous reference planes. Follow the Texas Instruments datasheet for the complete pin list, decoupling configuration, crystal or clock requirements, power sequencing, and layout geometry. This page combines the verified manufacturer characteristics with practical USB layout guidance, sourcing information, comparison fields, and engineering-oriented selection notes. It also identifies where detailed electrical, timing, mechanical, and configuration values must be obtained directly from the manufacturer datasheet.
TUSB8044RGCT - 4-Port 5Gbps USB 3.1 Hub | Texas Instruments
Texas Instruments TUSB8044RGCT is a 4-port SuperSpeed USB 3.1 hub controller with support for 5.0-Gbps signaling, a billboard interface, and I2C configuration support in a 64-pin VQFN (RGC) package measuring 9 x 9 mm. It is designed to manage one upstream SuperSpeed USB connection and four downstream SuperSpeed ports while providing the device coordination required for a multi-port USB hub. A USB hub controller is an interface integrated circuit that converts the physical USB topology of a host and multiple peripherals into an internally managed connection. Within the product hierarchy, the TUSB8044RGCT belongs to the USB interface controller class, interface IC category, and broader semiconductor ecosystem. Its four-port architecture reduces the need for separate host adapters when several compatible USB devices must share one upstream port. The primary headline specifications are a port count of 4, SuperSpeed data signaling at 5.0 Gbps, USB 3.1 support, and a 64-pin VQFN package. The billboard interface supports the device-side connection of USB Type-C cables, while I2C provides a configuration and control interface for system integration. The exact operating voltage, current limits, temperature range, USB power-delivery capabilities, and supported power modes should be confirmed against the manufacturer datasheet before a circuit is released. The TUSB8044 is positioned for systems that require more than one SuperSpeed USB connection from a single host port. Its four downstream-port architecture can support storage, external data-acquisition equipment, communications modules, and other USB peripherals when the host, cable, operating system, and downstream devices support the applicable USB specifications. The controller handles hub functions, while the system still requires suitable USB data routing, power, protection, and connector implementation. Typical uses include compact workstation peripherals, USB test equipment, industrial control systems, server-adjacent connectivity panels, and external storage or media appliances. In each case, the four-port hub reduces connector demand at the host while retaining a 5.0-Gbps SuperSpeed signal path for each compatible downstream link. Product configuration may be handled through I2C, simplifying integration with a supervising controller in larger equipment. The most important layout consideration is controlled-impedance routing of the high-speed USB differential pairs. Place the controller and its associated passive components close to the relevant connector or routing transition, keep return paths continuous, and follow the reference layout and layer stack in the manufacturer datasheet. Power sequencing, USB connector orientation, and advertised current capability must also be designed together rather than treated as independent requirements. This page organizes the known TUSB8044RGCT capabilities, practical application context, package information, sourcing questions, and design considerations. It also distinguishes directly supportable drop-in alternatives from options that cannot be claimed as pin-compatible replacements, helping engineers make package and functional comparisons before committing a USB hub design to production.
TUSB9260PVP - USB 3.0 to SATA Bridge | TI Storage
The Texas Instruments TUSB9260PVP is a SuperSpeed USB 3.0 to Serial ATA bridge based on an ARM Cortex-M3 microcontroller. It connects a USB 3.0 host interface to a SATA storage device and supports 1.1 V, 1.8 V, and 3.3 V supply rails. The device is offered in a 64-pin HTQFP package with an exposed pad, measuring 7 mm by 7 mm. A USB-to-SATA bridge is an interface controller that translates commands and data between a USB host and a Serial ATA drive. This USB 3.0-to-SATA bridge sits within the interface-controller and storage-connectivity hierarchy, allowing compatible storage equipment to use USB connectivity while retaining a SATA device interface. Its microcontroller-based implementation supports the command, data, and power-management functions needed for USB-attached storage. The TUSB9260PVP provides SuperSpeed USB 3.0 operation together with USB 2.0 support, enabling it to serve as the storage interface in systems that need backward compatibility with slower USB links. The manufacturer identifies the product as a USB 3.0-to-Serial ATA bridge, while the component listing identifies the interface as an SPI serial interface with 1.1 V, 1.8 V, and 3.3 V supply options. The TUSB9260 architecture combines an ARM Cortex-M3 microcontroller with dedicated USB-to-SATA bridge hardware and firmware support. This implementation is intended to provide the necessary protocol translation for USB-attached storage devices. Designers should allocate separate routing for high-speed USB and SATA signals, maintain continuous return-path references, and observe the exposed-pad requirements of the HTQFP package. Typical uses include external storage enclosures, USB-to-SATA adapters, backup appliances, and industrial data-acquisition systems that require an established USB 3.0 host connection to a SATA drive. The device can also serve in equipment where a legacy SATA storage interface must remain accessible through a newer USB-facing system architecture. Layout quality is central to reliable SuperSpeed operation. Place differential USB and SATA pairs over continuous ground planes, use short matched routing, minimize stub lengths, and provide low-impedance power distribution for 1.1 V, 1.8 V, and 3.3 V rails. Follow the manufacturer pin-description table and layout guidance when assigning tracks and connecting the exposed thermal pad. This product page combines the exact package, supply, interface, and lifecycle characteristics with a design-focused comparison against TUSB9261PVP. It also identifies practical implementation considerations for USB 3.0-to-SATA storage products and distinguishes documented pin-compatible upgrades from alternatives requiring broader hardware validation.
TUSB9261-Q1 - USB 3.0 to SATA Bridge AEC-Q100 | TI
The Texas Instruments TUSB9261-Q1 is an automotive-qualified, ARM Cortex-M3 microcontroller-based USB 3.0 to Serial ATA (SATA) bridge delivered in a 64-pin HTQFP package rated for -40C to +85C operation. It provides the hardware and firmware needed to implement a USB Attached SCSI Protocol (UASP)-compliant mass storage device, bridging HDDs, SSDs, optical drives, and other SATA 1.5-Gbps or SATA 3.0-Gbps devices to a SuperSpeed USB 3.0 host. A bridge IC is a dedicated interface converter that sits between two different bus protocols and translates transactions between them. Within the interface IC hierarchy (bridge -> USB interface controller -> interface IC -> semiconductor), the TUSB9261-Q1 belongs to TI's second generation of SuperSpeed USB-to-SATA bridges, specifically qualified for automotive applications per AEC-Q100, with a device CDM ESD classification of Level C3 as the noted exception. Key features include an embedded ARM Cortex-M3 processor core running TI firmware for UASP compliance, native support for SATA 1.5-Gbps and 3.0-Gbps device classes, and USB 3.0 SuperSpeed 5-Gbps connectivity on the host side. UASP support delivers significantly higher command queuing efficiency than legacy BOT (Bulk-Only Transport), reducing latency and improving throughput with modern SSDs. Integrated PHYs reduce external component count and BOM cost. The Cortex-M3 architecture allows TI to update bridge firmware, adding features and fixing interoperability issues without hardware changes, which is valuable for long-lifecycle automotive programs. AEC-Q100 qualification supports infotainment, telematics, and diagnostic ports where USB-attached storage must survive automotive temperature and ESD environments. Typical applications include automotive infotainment USB storage ports, in-vehicle diagnostic data loggers with SSD storage, and external HDD/SSD docking designs requiring automotive grade qualification. Design consideration: this device is flash-based firmware dependent; plan for firmware update provisions (I2C/EEPROM boot) in the PCB layout, and observe the datasheet note regarding SATA pin swapping documented on the TI E2E forum before finalizing routing.
TUSB9261PVP - 5Gbps USB 3.0 to SATA Bridge | Texas Instruments
The Texas Instruments TUSB9261PVP is a USB 3.0 to serial ATA bridge that operates at 5 Gbps on the USB side and bridges compatible SATA 1.5 Gbps or SATA 3.0 Gbps storage devices. It is a second-generation SuperSpeed USB bridge controller based on an ARM Cortex-M3 microcontroller, supplied in a 64-lead HTQFP package measuring 7 mm by 7 mm. A USB-to-SATA bridge is an interface controller that translates commands and data between USB and the Serial ATA protocol. Its place in the product hierarchy is USB interface bridge, then interface IC, then semiconductor. TUSB9261PVP provides the hardware and firmware needed to implement a USB Attached SCSI Protocol, or UASP, compliant mass-storage device. It can therefore connect external HDD, SSD, and optical-drive interfaces to a USB 3.0 host while preserving a native bridge-oriented architecture. The TUSB9261PVP combines a 5 Gbps USB 3.0 interface with support for both 1.5 Gbps and 3.0 Gbps SATA devices. Its operating supply range is 3 V to 3.6 V, and the integrated ARM Cortex-M3 microcontroller provides programmable control for the bridge function. The device is intended for storage applications that require higher transfer rates than USB 2.0 can provide while maintaining compatibility with multiple SATA generations. Technical differentiation is primarily functional rather than a simple electrical upgrade. A USB-to-SATA bridge handles protocol translation, command handling, device detection, and data transfer between a USB host and SATA storage media. Supporting both SATA 1.5 Gbps and SATA 3.0 Gbps allows one bridge design to cover legacy and higher-speed SATA devices. The 64-lead HTQFP package also provides a substantial pin count for high-speed interfaces, power connections, control signals, and configuration functions. Typical applications include external HDD enclosures, external SSD adapters, USB 3.0 storage docks, optical-drive bridges, portable storage accessories, and industrial storage systems that connect a SATA-compatible device to a USB 3.0 host. The UASP capability is especially relevant to systems intended to reduce command-processing overhead through a standards-based mass-storage protocol. PCB design should prioritize short, impedance-controlled routing for USB and SATA differential pairs, solid return paths, careful separation between high-speed and sensitive signals, and power-plane integrity near the bridge. Use the pin-description and layout guidance in the manufacturer datasheet when assigning tracks, and follow its recommended input and output capacitor network. This page combines the manufacturer interface description with package information, application guidance, comparison criteria, and practical PCB recommendations. It is intended to help engineers identify the correct bridge, confirm protocol compatibility, and plan a USB 3.0-to-SATA storage design before schematic capture and layout.
TVP5146M2PFP - 10-bit NTSC/PAL/SECAM Video Decoder | TI HTQFP-80
The Texas Instruments TVP5146M2PFP is a 10-bit high-quality single-chip digital video decoder that digitizes and decodes all popular baseband analog video formats - including NTSC, PAL, SECAM composite, S-Video, component RGB and YPbPr - into digital component video, housed in an 80-pin PowerPAD HTQFP package (12x12 mm). It integrates Macrovision detection, a 5-line adaptive comb filter, SCART support, and four 30 MSPS 10-bit ADC channels, replacing multiple discrete decoder/filter ICs in mainstream consumer video designs. A digital video decoder is a mixed-signal IC that converts legacy analog broadcast and consumer video signals into a digital YCbCr or RGB pixel stream for downstream processing by a scalar, encoder, SoC, or capture ASIC. Within the broader taxonomy of mixed-signal ICs, the TVP5146M2 belongs to the video decoder family, which sits below video processors and above simple video amplifiers in the signal-chain hierarchy. Multi-standard support (NTSC M/N/4.43, PAL B/G/H/I/M/N/60, SECAM) allows one hardware design to ship worldwide without regional BOM variants. Key differentiating specifications include four integrated 10-bit ADCs sampling at up to 30 MSPS, an integrated 5-line adaptive comb filter for superior chroma/luma separation, Macrovision copy-protection detection, and 12 analog front-end inputs that multiplex automatically - composite, S-Video, component YPbPr, RGB, and SCART - under software control via I2C. Programmable gain, clamp, and offset on each channel allow direct connection to consumer-grade video sources without external op-amps. Architecture is built around TI's analog front-end, 10-bit ADC array, comb filter, and digital formatter block. The decoder outputs 8/16-bit ITU-R BT.601/BT.656 or 20-bit ITU-R BT.1120 digital component video, and supports both 2x and 1x oversampling modes. An internal color-space converter generates YCbCr and RGB outputs simultaneously, reducing host CPU overhead and shortening time-to-market for set-top box, DVR, and capture-card designs. Typical applications include set-top boxes and DVRs decoding composite or component broadcast video, USB video capture cards capturing VHS/DVD or legacy consoles, video conferencing codecs, surveillance DVRs, and automotive rear-seat entertainment head units that digitize external composite sources. The wide input tolerance also suits broadcast monitor walls and medical imaging reference inputs. When laying out a PCB, allocate a solid ground plane beneath the PowerPAD and stitch the exposed pad with at least 9 thermal vias to the inner ground layer. Use 75 ohm-controlled-impedance routing on all analog video inputs to preserve 2T pulse response, and place anti-alias RC networks within 5 mm of each analog pin. Decouple both 1.8 V and 3.3 V rails with 0.1 uF X7R ceramics in parallel with 10 uF bulk capacitors at the supply pins. This page synthesizes distributor pricing from Mouser and DigiKey, drop-in same-package alternatives, and practical design notes (PCB layout, thermal pad, decoupling) not found in the manufacturer datasheet alone, giving engineers a one-stop reference for the TVP5146M2PFP.
TVP5147M1PFPR - 10-bit NTSC/PAL/SECAM Video Decoder | TI HTQFP-80
The Texas Instruments TVP5147M1PFPR is a 10-bit high-quality single-chip digital video decoder that digitizes and decodes NTSC, PAL, and SECAM analog composite, S-Video, and component YPbPr signals into digital component video (YCbCr 4:2:2), housed in an 80-pin HTQFP (PFP) PowerPAD package with 12x12 mm body. According to TI product page, it integrates two 10-bit ADCs, a 5-line adaptive comb filter, and Macrovision 1.x/2.x detection, providing a complete analog front-end plus decoder in a single device. What is a video decoder? A video decoder is a type of interface IC that converts analog baseband video signals (composite CVBS, Y/C, or YPbPr component) into digital ITU-R BT.656 or BT.601 video streams. Within the broader taxonomy, video decoders belong to encoders/decoders/converters in interface ICs, sitting between analog video sources (tuners, cameras, DVD players) and digital video processors (DSPs, SoCs, FPGAs). They are essential building blocks in LCD TV/Monitor designs where legacy analog video must be displayed on digital panels. The TVP5147M1's key differentiating features include a hardware Macrovision detection circuit (Macrovision 1.x and 2.x compliant), a 5-line adaptive comb filter for superior luminance/chrominance separation in NTSC/PAL, automatic gain control with peak/average modes, and TI's proprietary chroma transient improvement (CTI) and luminance peaking circuitry. The device supports ten analog input channels selected via I2C, programmable H/V sync outputs, VBI data slicing for teletext/closed caption, and outputs ITU-R BT.656, BT.601, or raw VBI data over an 8- or 16-bit parallel interface. A single 27 MHz reference clock serves all standard video formats. Architecturally, the TVP5147M1 combines two 10-bit, 30 MSPS ADCs with a programmable automatic gain control, a chroma demodulator with subcarrier PLL, a 5-line comb filter, and a digital output formatter. Analog supplies are 1.8 V (analog) and 3.3 V (I/O), while the digital core runs from an internally regulated 1.8 V supply. The HTQFP-80 PowerPAD package provides a thermal pad that must be soldered to a ground plane for adequate heat dissipation; PowerPAD operation lowers junction temperature and improves long-term reliability in always-on consumer equipment. Typical applications include LCD TV and LCD monitor analog video inputs, set-top boxes archiving analog broadcasts, digital video recorders (DVR), video capture cards for PCs, in-car rear-seat entertainment displays, and security DVR systems. The Macrovision detection makes it suitable for licensed playback equipment where copy protection circuitry is mandated by content owners. When designing with this device, ensure the PowerPAD is soldered to a continuous ground copper pour with multiple thermal vias to maximize heat flow. Use a 27 MHz crystal with low jitter (<50 ps RMS) to minimize pixel-clock jitter on the digital output, which directly impacts downstream display quality. Decouple the 1.8 V analog and 3.3 V I/O rails with 0.1 uF and 10 uF ceramic capacitors placed as close to the supply pins as practical. This page synthesizes distributor pricing, drop-in alternatives, Macrovision-equipped pin-compatible parts, and practical design notes not found in the manufacturer datasheet alone.
TVP5150AM1IPBS - Ultra-Low Power NTSC/PAL/SECAM Video Decoder | TI
The Texas Instruments TVP5150AM1IPBS is an ultralow-power NTSC/PAL/SECAM video decoder that converts baseband analog video (composite, S-Video, or component Y/C) into 8-bit ITU-R BT.656 digital output. Housed in a 32-pin TQFP (PBS) 5x5 mm package, it integrates a high-speed 9-bit ADC, two composite or one S-Video input, and fully differential CMOS analog preprocessing channels with clamping and automatic gain control (AGC) for best signal-to-noise performance. What is a video decoder? A video decoder is a mixed-signal integrated circuit that digitizes analog broadcast video (NTSC, PAL, SECAM) and reformats it into a standard digital stream that downstream processors, image signal processors (ISPs), or video encoders can consume. In the broader taxonomy, the TVP5150AM1IPBS sits under video front-end ICs -> interface ICs -> integrated circuits, and historically it dominated mobile, surveillance, and set-top box designs where small footprint and low power were non-negotiable. Key features include a robust sync detector for non-standard and weak signals, Genlock/real-time control (RTC) output for synchronizing downstream encoders, complementary 4-line adaptive comb filtering for both luminance and chrominance paths, and a programmable chrominance trap filter. Per the TI datasheet, power consumption is typically below 150 mW, and the device operates from a 1.8 V core supply with a 3.3 V I/O supply via an integrated level shifter. Technically, the device uses a 9-bit pipelined ADC architecture, two fully differential analog preprocessing channels, and an on-chip PLL to generate the 27 MHz sampling clock from a 27 MHz crystal or external reference. The I2C interface is used for configuration of video standard, brightness, contrast, saturation, hue, and comb-filter enable, while the parallel 8-bit output uses the ITU-R BT.601 or BT.656 interface standard. Typical applications include handheld/personal video recorders, mobile phone video capture, portable media players, digital still cameras, automotive infotainment rear-seat displays, and CCTV/DVR surveillance front ends where composite CVBS must be digitized for compression ASICs or SoCs. When designing with this device, provide adequate bulk decoupling on both the 1.8 V (DVDD) and 3.3 V (IO_DVDD) rails and route the analog video inputs with controlled 75 ohm impedance to minimize reflections. The S-Video Y/C pair is preferred over CVBS for best comb-filter performance.
TVP5150AM1PBS - Ultralow-Power NTSC/PAL/SECAM Video Decoder | TI
The Texas Instruments TVP5150AM1PBS is an ultralow-power NTSC/PAL/SECAM analog video decoder that converts baseband composite or S-Video inputs to 8-bit ITU-R BT.656 digital YCbCr 4:2:2 output (or discrete syncs), housed in a 32-terminal TQFP (PBS) package. It integrates a 9-bit high-speed analog-to-digital converter sampling at 27 MHz, two composite or one S-Video input channel with automatic gain control and clamping, and a robust sync detector. Operating from 1.65 V to 1.95 V (digital) and 1.65 V to 1.8 V (analog), it accepts NTSC (J, M, 4.43), PAL (B, D, G, H, I, M, N, Nc), and SECAM (B, D, G, K, K1, L) video standards. A video decoder is an integrated circuit that captures analog composite or S-Video signals and converts them into a digitized component video stream for downstream processing by application processors, SoCs, or display controllers. The device category hierarchy is: video decoder -> analog front-end -> interface IC -> semiconductor. Its role in a typical embedded vision system is to bridge analog cameras or legacy analog video sources (CVBS, Y/C) to modern digital processing pipelines, eliminating the need for external ADCs and sync separators while preserving signal integrity. Key features include a high-speed 9-bit ADC, fully differential CMOS analog preprocessing with AGC and clamping for best signal-to-noise performance, complementary 4-line adaptive comb filtering on both luminance and chrominance paths, Macrovision copy-protection support, and an ultralow-power architecture suited to portable designs. A Genlock/real-time control (RTC) output is generated for synchronizing downstream video encoders in multi-camera or PIP architectures. Technically, the TVP5150AM1 uses a differential analog front end that rejects common-mode noise and supports extended temperature operation from 0°C to 70°C in the PBS package variant. Its register-based I²C control interface exposes luminance, chrominance, hue, brightness, contrast, and sharpness adjustments to the host processor. Typical applications include portable media players, set-top boxes, digital video recorders, video capture cards, automotive infotainment rear-seat entertainment, IP cameras with analog CVBS input, and surveillance DVRs. The wide standard coverage and ultralow-power operation make it suitable for any embedded design that must decode legacy analog video. When designing with this part, pay attention to the I/O supply sequencing constraint: IO_DVDD must track the 1.8 V digital supply and must not be back-powered; an external power-on-reset (POR) or supply sequencing network may be required for multi-supply rails. Place the 27 MHz crystal or clock source within 5 mm of the XTAL pin and use a star-ground topology for the CVBS traces. This page synthesizes distributor pricing, pin-compatible TI replacements (TVP5150AM1PBSR, TVP5150AM1IPBS, TVP5151IPBSR), and practical PCB-layout guidance not found in the manufacturer datasheet alone.
TVP5150PBS - Ultralow-Power NTSC/PAL Video Decoder, 32-TQFP
The Texas Instruments TVP5150PBS is an ultralow-power NTSC/PAL video decoder housed in a 32-pin TQFP (PBS) package. It accepts analog composite or S-Video inputs and converts them to 8-bit ITU-R BT.656 digital video at standard definition, dissipating only 113 mW in typical operation and less than 1 mW in power-down mode. The integrated 9-bit high-speed ADC and fully differential CMOS analog preprocessing channels with clamping and AGC provide best-in-class signal-to-noise performance for mobile and embedded video capture. A video decoder is a mixed-signal interface IC that translates analog broadcast waveforms (NTSC, PAL, SECAM) into digital YCbCr pixel streams for downstream encoders, scalers, or SoCs. Within the broader power-management and interface taxonomy, the TVP5150 belongs to the video front-end category, sitting between an analog sensor or CVBS input and a digital video processor. Its ultralow-power architecture makes it a defining member of the low-power video decoder family, replacing legacy multi-chip decoder solutions with a single integrated device. Key features include support for NTSC (M, N, 4.43) and PAL (B, D, G, H, I, M, N) standards with ITU-R BT.601 sampling, two composite or one S-Video input with on-chip source selection, hardware scaling, brightness/contrast/hue/saturation controls, and a synchronous serial interface for host configuration. The macrovision detection circuitry and chroma trap filtering are integrated to simplify downstream software requirements. The TVP5150 uses a 27 MHz reference clock and produces ITU-R BT.656 output with embedded sync, or alternatively discrete syncs (HSYNC, VSYNC, FIELD) for processors that require them. A synchronous serial host port (I2C-compatible) configures video standard detection, scaling, output format, and test patterns. Internal PLLs regenerate the sample clock from the video input, eliminating the need for external line-locked crystals. Typical applications include portable media players, handheld DVRs, IP network cameras, video doorbells, machine-vision modules, and automotive rear-seat infotainment displays. The 32-TQFP footprint and low power budget make it especially suitable for battery-powered designs where thermal dissipation must be minimized. When designing with the TVP5150PBS, ensure the analog input traces are impedance-controlled (75 ohm) and routed away from digital switching nodes. The 27 MHz reference clock must be stable within 50 ppm to avoid chroma decoding artifacts. Decouple AVDD and DVDD separately with 0.1 uF and 10 uF ceramic capacitors placed within 5 mm of the supply pins. This page synthesizes distributor pricing, drop-in alternative listings, and practical design notes that extend beyond the manufacturer datasheet, providing a single reference for engineers selecting or replacing the TVP5150PBS.
TVP5151IPBSR - Ultralow-Power NTSC/PAL/SECAM Video Decoder | TI
The Texas Instruments TVP5151IPBSR is an ultralow-power NTSC/PAL/SECAM video decoder housed in a 32-pin TQFP (PBS) package measuring 5x5 mm. It accepts composite (CVBS) and S-Video analog inputs and converts them to 8-bit ITU-R BT.656 digital video with embedded syncs, or to 8-bit 4:2:2 with discrete syncs. The decoder supports NTSC (J, M, 4.43), PAL (B, D, G, H, I, M, N, Nc), and SECAM (B, D, G, K, K1, L) standards with automatic standards detection and Macrovision copy-protection detection. A video decoder is a mixed-signal integrated circuit that digitizes analog baseband video from cameras, set-top boxes, or playback devices so a digital processor, image signal processor, or display controller can consume the stream. Within the converter family hierarchy, the TVP5151 belongs to video ADCs / video decoders, which sit under data converters, then signal conditioning, then analog front-end ICs. The part integrates a 9-bit ADC front-end, an analog front-end with automatic gain control, chroma processing, and a digital output formatter on a single die. Key specifications include ultralow power consumption (the decoder core draws only 138 mW from a 1.7 V analog and 1.8 V digital supply), a 32-terminal TQFP (PBS) plastic package, and an I2C-compatible host interface for programming output format, brightness, contrast, saturation, hue, and VBI data slicing. The TVP5151I industrial grade supports the -40 C to +85 C temperature range, while the standard TVP5151 supports 0 C to 70 C. The integrated anti-alias filter and 2D/3D comb filter reduce external BOM, enabling compact camera, surveillance, and consumer designs. Typical applications include portable media players, IP/security cameras, video capture cards, machine vision front-ends, digital photo frames, automotive infotainment displays (commercial grade only - TVP5150A is the automotive AEC-Q-qualified variant), and set-top box video output stages. The 138 mW consumption makes it particularly attractive for battery-powered camcorders and handheld capture cards. When designing with this device, ensure a clean analog supply with ferrite-bead isolation between the analog 1.8 V rail and digital 1.8 V rail. Provide a stable 14.31818 MHz VCO reference for the decoder's internal timing recovery. Use series 75-ohm termination at the analog video inputs and route them away from digital switching traces to minimize crosstalk into the ADC. This page synthesizes distributor pricing, drop-in cross-reference alternatives, design notes, and a parametric comparison table not bundled in the manufacturer datasheet, with all values anchored to TI's TVP5151 datasheet and current DigiKey/Mouser inventory as of 2026-10-20.
TVP5154AIPNP - 4-Ch Video Decoder 128-HTQFP | Texas Instruments
The Texas Instruments TVP5154AIPNP is a 4-channel, low-power NTSC/PAL/SECAM video decoder with independent scalers, housed in a 128-pin HTQFP (PNP) PowerPAD package measuring 14x14 mm. Each of the four channels converts analog composite or S-Video inputs into 8-bit ITU-R BT.656 digital video output, with independent scaling and fast locking on a per-channel basis. The device shares a single external crystal across all four decoder channels, simplifying multi-camera security and surveillance designs. A video decoder is an integrated circuit that converts analog baseband video signals (such as those from legacy CCTV cameras, broadcast receivers, or DVD players) into digital component video that can be processed by a host processor, SoC, or FPGA. The TVP5154AIPNP belongs to the broader family of mixed-signal video interface ICs that sit between the analog front end and the digital video pipeline, classified as encoder/decoder/converter ICs within the Interface ICs product hierarchy. Multi-channel decoders like the TVP5154AIPNP are indispensable in modern security DVRs, automotive rear-view systems, and quad-display controllers. Key features include four independent decoder channels each supporting composite (CVBS) and S-Video (Y/C) inputs, automatic NTSC/PAL/SECAM format detection, on-chip anti-aliasing filters, and programmable hue/brightness/contrast/saturation controls. The integrated horizontal and vertical scalers allow each channel to downscale arbitrarily before output to BT.656, dramatically reducing the downstream host CPU load and DMA bandwidth. Internally, the TVP5154AIPNP uses a 9-bit ADC per channel combined with a digital comb filter for chroma/luma separation. The fast-lock PLL achieves full synchronization in under 150 ms, while a single 27 MHz crystal drives all four channels. The host interface is a standard I2C control port, and the video output bus is configurable for 8-bit BT.656 or discrete syncs. Typical applications include 4-channel CCTV security DVRs that record four camera feeds simultaneously, video capture cards for PCIe surveillance backplanes, automotive surround-view systems, and industrial machine-vision inspection rigs where multiple analog cameras are coordinated. Each application benefits from the decoder's small PCB footprint per channel and shared crystal economy. When designing with this device, allocate adequate PCB area for the exposed thermal pad beneath the HTQFP-128 package to dissipate approximately 0.6 W of total power across all four active channels. Decouple all four analog AVDD supplies independently and follow TI's recommended 75-ohm analog input termination at each CVBS pin. This page synthesizes distributor pricing, application notes, and pin-compatible alternatives consolidated from TI's product catalog and authorized distributors, providing practical guidance not always available in the bare datasheet.
TVP5154AIPNPR - 4-Ch PAL/NTSC/SECAM Video Decoder | TI
The Texas Instruments TVP5154AIPNPR is a 4-channel, low-power NTSC/PAL/SECAM video decoder with independent scalers and fast lock, housed in a 128-pin HTQFP (PNP) PowerPAD package measuring 14x14 mm. Each of the four independent channels converts analog composite video (CVBS) or S-Video signals into 8-bit ITU-R BT.656 digital output, with discrete syncs also available. The device operates from a 1.8 V core supply and a 3.3 V I/O supply, drawing very low power per channel which makes it well-suited to dense multi-channel surveillance designs. A video decoder is an analog-front-end IC that digitizes analog broadcast video formats (NTSC, PAL, SECAM) so that downstream processors, DSPs, FPGAs, or SoCs can perform image processing, encoding, or display. The TVP5154A's 4-channel architecture targets space-constrained multi-camera systems; each channel shares one external crystal, but exposes independent control registers, scalers, and output paths so that four simultaneous captures can run at different resolutions. Key features include four independent video-decoder channels, on-chip independent horizontal/vertical scalers, fast-lock PLL per channel, automatic standard detection, 8-bit ITU-R BT.656 / discrete-sync output, I2C control interface, low standby current, and integrated anti-aliasing filters. The fast-lock PLL shortens channel acquisition time, which is critical when sequentially switching between camera inputs. Technically, the TVP5154A uses a 9-bit ADC per channel followed by a comb-filter Y/C separator and a programmable scaler. The 128-pin HTQFP PowerPAD provides a low-thermal-resistance path (theta_JC in single-digit C/W range) so all four channels can operate continuously without active cooling. The device is qualified to the industrial temperature range (-40C to +85C). Typical applications include 4-channel CCTV/DVR surveillance capture cards, multi-channel video conferencing front-ends, automotive multi-camera DVRs, video capture PCIe/USB adapters, and broadcast monitoring equipment. When designing with this part, share one 27 MHz crystal across all four channels and decouple each analog supply pin individually. Place the PowerPAD solder stencil directly under the exposed pad and tie it to a solid analog ground plane for thermal dissipation.
TVP5158IPNPR - 4Ch NTSC/PAL Video Decoder, 128-HTQFP | Texas Instruments
The Texas Instruments TVP5158IPNPR is a four-channel high-quality NTSC/PAL video decoder that digitizes and decodes all popular base-band analog video formats into digital video output. Each of the four channels integrates a 10-bit 27-MSPS analog-to-digital converter (ADC) preceded by an analog input conditioning circuit that clamps the input to a reference and applies anti-alias filtering. The device is offered in a 128-pin HTQFP (PNP) package measuring 14x14 mm with an exposed thermal pad, targeting multi-channel security and machine-vision applications. A video decoder is a mixed-signal integrated circuit that converts analog composite video signals (such as those from CCTV cameras or legacy broadcast outputs) into a digital component video stream for downstream processing by a host processor, SoC, or DSP. The TVP5158 belongs to the broader category of video interface ICs within the interface and signal-chain family. It supports NTSC (J, M, 4.43) and PAL (B, D, G, H, I, M, N, Nc, 60) standards, providing global compatibility for surveillance equipment that must accept feeds from mixed regional cameras. Key features include four fully independent video processing channels, each with its own scaler, 2D noise reduction, auto-contrast enhancement, and flexible output formatting. Independent per-channel scaling allows different display resolutions per input without external logic, while integrated noise reduction cleans low-light analog camera feeds. An I²C control interface manages all programming. The HTQFP-128 (PNP) package provides manageable thermal performance for the four ADCs running simultaneously, suitable for security DVRs, video capture cards, and industrial inspection equipment. The architecture combines four parallel analog front-ends with per-channel digital decoders, enabling concurrent decoding of four composite video streams at up to 27 MSPS per channel. This high integration reduces the bill of materials for multi-channel DVRs by replacing four single-channel decoders plus glue logic with a single chip, simplifying board layout and reducing power consumption in space-limited surveillance chassis. Typical applications include multi-channel digital video recorders (DVRs), surveillance capture cards, multi-camera video mixing equipment, industrial machine-vision systems, and broadcast monitoring receivers. Each application leverages the four independent decoder channels and integrated scaling to consolidate what would otherwise require multiple discrete decoder chips into a single footprint. Designers should pay close attention to PCB layout around the four high-speed analog inputs: each analog input must be guarded by a ground ring and routed as a 75-ohm impedance-controlled differential pair to minimize crosstalk between channels. The exposed thermal pad must be soldered to a continuous ground plane to dissipate heat generated by four concurrent ADCs. This page synthesizes distributor pricing, same-brand alternatives (including the discontinued TVP5158IPNP base part), and practical layout notes that complement the manufacturer datasheet.
TVP5160PNP - NTSC/PAL/SECAM 10-Bit Video Decoder HTQFP-128 | TI
The Texas Instruments TVP5160PNP is a high-quality digital video decoder that digitizes and decodes all popular baseband analog video formats into digital component video, integrating two 11-bit 60-MSPS analog-to-digital converters with analog preprocessors, fixed RGB-to-YUV color space conversion, and Macrovision detection. Housed in a 128-pin HTQFP (PNP) package measuring 14x14 mm, the device supports NTSC (J, M, 4.43), PAL (B, D, G, H, I, M, N, Nc, 60) and SECAM (B, D, G, K, K1, L) composite and S-Video inputs as well as component YPbPr and RGB (SCART) signals. A video decoder is an analog front-end IC that converts legacy analog video waveforms - originally designed for CRT displays - into digital YCbCr component streams for downstream processing by display controllers, scalar ASICs, video processors, or application processors. In the broader taxonomy the TVP5160 sits at: video decoder -> AFE (analog front end) -> display controller companion IC -> multimedia SoC ecosystem IC. Its 3D-YC/5-line comb filter provides robust chroma/luma separation for noisy or weak broadcast signals, while integrated AGC and clamping stages reduce the external BOM typically required around discrete ADCs. Key features include an integrated analog front-end containing two 11-bit 60 MSPS ADCs with clamping and AGC, fixed RGB-to-YUV color space conversion (eliminating external matrix math), robust sync detection optimized for weak and noisy signals as well as VCR playback, Macrovision detection, and 3D-YC / 5-line adaptive comb filtering. The decoder produces digital component video (YCbCr 4:2:2) on its output port for downstream processing. Operating voltage spans 3.0V to 3.6V (3.3V typical) with typical power dissipation of 904 mW. The HTQFP-128 footprint and 0 to 70C operating temperature range target commercial-grade LCD TV and monitor designs. Architecturally, the TVP5160 uses two time-interleaved 11-bit pipelined ADCs feeding an on-chip digital signal processor that performs sync separation, chroma demodulation, comb filtering, and color space conversion. The fixed RGB-to-YUV block is hard-wired (not programmable) which reduces silicon cost versus fully programmable decoders such as the TVP5150. The Macrovision detection path is a passive observer - it does not strip Macrovision, it copies to data so downstream content-protection logic can take the response. Typical applications include LCD TV main boards, monitor main boards, video capture cards, set-top box front-ends, and DVR/PVR baseband inputs. The TVP5160 is particularly useful when accepting multiple legacy input standards (composite CVBS, S-Video Y/C, component YPbPr, SCART RGB) on a single board because one decoder replaces several discrete solutions. The Macrovision detection path also enables DRM-aware DVR designs. When designing with this device, ensure that input ESD protection and 75-ohm termination are placed as close to the connectors as possible because the TVP5160's analog front-end is sensitive to PCB-level mismatches and ESD events. A 27 MHz crystal or external clock drives the ADC sample rate - tolerate +/- 50 ppm for broadcast-grade decoding. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet, enabling a faster engineering decision for LCD TV and monitor main-board designs.
TXB0104-Q1 - 4-Bit Auto-Direction Level Translator | TI
The Texas Instruments TXB0104-Q1 is an automotive-grade 4-bit bidirectional voltage-level translator with automatic direction sensing and +/-15 kV ESD protection, available in a 14-pin TSSOP (PW) package. It translates between two independent supply rails: the A port tracks VCCA from 1.2 V to 3.6 V, while the B port tracks VCCB from 1.65 V to 5.5 V, enabling any-to-any translation between 1.2 V, 1.8 V, 2.5 V, 3.3 V and 5 V logic domains. A voltage-level translator is a logic-family device that allows integrated circuits operating at different supply voltages on the same PCB to exchange digital signals safely. Within the power-and-signal-management hierarchy, it sits alongside buffers and bus switches as a fundamental interface IC, preventing overvoltage damage and ensuring valid logic thresholds between low-voltage MCUs, FPGAs, and 5 V peripherals. Key features include auto-direction sensing, which eliminates the DIR control pins required by '245-style translators, a data rate of up to 100 Mbps, and VCC isolation: when either supply is at GND, all I/O enters Hi-Z. The AEC-Q100-qualified TXB0104-Q1 also carries +/-15 kV HBM ESD protection, exceeding the standard JESD ratings cited in the TI datasheet family. Architecturally, the TXB0104 uses a self-directed, edge-rate-driven one-shot scheme that detects the direction of each transition and briefly strengthens the opposite driver, allowing it to drive 4 channels in either direction without software intervention. The OE pin three-states all outputs for power sequencing and bus isolation. Typical applications include SPI and UART level conversion between 3.3 V MCUs and 5 V peripherals, GPIO expansion in automotive body and infotainment modules, and mixed-voltage FPGA I/O. Note that the push-pull architecture is not recommended for open-drain buses such as I2C or 1-Wire; use the TXS0104E-Q1 for those. Design consideration: keep unloaded outputs low-impedance driven or grounded, since the auto-direction circuitry can oscillate on lightly loaded or capacitively large nets; series resistors above 25 k-ohm are not supported. This page adds value beyond the TI datasheet by synthesizing distributor availability, drop-in alternatives (NXP NTS0304E, ADI ADG3304), and practical design notes for automotive level-shifter selection.
TXB0304RSVR - 4-Bit Bidirectional Level Translator 100Mbps | TI
The Texas Instruments TXB0304RSVR is a 4-bit bidirectional voltage-level translator with automatic direction sensing, designed for mixed-voltage systems. It operates with two separate power-supply rails, VCCA and VCCB, each configurable from 0.9V to 3.6V, and supports data rates up to 100 Mbps in a 16-pin UQFN (RSV) package measuring 2.6mm x 1.8mm, ideal for space-constrained designs. A voltage-level translator is a crucial component in modern electronics, allowing communication between ICs operating at different voltage levels. For example, a 1.8V microcontroller can interface with a 3.3V sensor or memory device without risking damage or logic errors. The TXB0304 belongs to the TXB family of auto-direction-sensing translators, part of TI's broader level-shifting portfolio that includes unidirectional and bidirectional solutions for various interface standards. Key features include a fully symmetric supply range (0.9V to 3.6V on both VCCA and VCCB), automatic direction sensing that detects data flow without external direction control, and a high data rate of 100 Mbps. The device also provides an isolation function: if either VCC input is at GND, all outputs are placed in a high-impedance state, preventing backflow current and protecting the system. Technically, the TXB0304 uses a one-shot circuit to accelerate rising edges, ensuring fast signal propagation even with capacitive loads. The architecture includes a pass-gate transistor with a pull-up resistor on each I/O pin, providing robust translation. The device is specified from -40C to +85C, is RoHS compliant and lead-free. Typical applications include SPI, I2C, UART, and GPIO interfacing between microcontrollers, sensors, memory, and peripherals at different voltage levels, particularly in IoT devices, portable electronics, and industrial control systems. Design tip: ensure both VCCA and VCCB are powered and place decoupling capacitors close to the power pins. Note that push-pull drivers are preferred; open-drain buses require external pull-ups sized carefully.
TXB0604 - 4-Bit Auto-Bidirectional Level Translator 345Mbps | TI
The Texas Instruments TXB0604 is a 4-bit non-inverting auto-bidirectional voltage level translator that uses two separate configurable power-supply rails: the A port tracks VCCA (0.9V to 2V) and the B port tracks VCCB (1.65V to 3.6V), with the constraint VCCA <= VCCB. It supports data rates exceeding 345Mbps with a 15pF load and over 190Mbps with a 100pF load, and is supplied in a 14-pin TSSOP (PWR) package with a 12-pin X2QFN (1.6x1.6mm) option (RWBR). A voltage level translator is an integrated circuit that allows digital signals to cross between different voltage domains, ensuring valid logic levels and signal integrity in mixed-voltage systems. Within the interface hierarchy, level shifters sit between logic devices and buses, and auto-bidirectional translators eliminate the direction-control pin by automatically sensing data flow. Key features include TI's patented architecture achieving high data throughput for memory-intensive interfaces like Quad-SPI between a Baseboard Management Controller (BMC) and Flash devices, without signal-integrity losses from excessive output parasitic capacitance. The device also provides partial power-down protection (Ioff), Vcc disconnect, Vcc isolation, and integrated pull-up resistors on the A and B ports. Wettable-flank packages enhance solder-joint inspection for automotive-quality assembly. Technically, the TXB0604 functions as both a voltage translator and a line redriver: a one-shot edge accelerator sharpens rising edges, reducing propagation delay, while boosted drive strength enables signal boosting over long-cable transmission. Compared to the legacy TXB0104 (100Mbps), the TXB0604 delivers over 3x the data rate with stronger capacitive load driving. Typical applications include Quad-SPI and Octal-SPI buses between BMCs and Flash memory, eSPI interfaces, and mixed-voltage processor-to-peripheral links in servers, networking equipment, and industrial systems. Design tip: always ensure VCCA <= VCCB, place decoupling capacitors close to both supply pins, and avoid floating unused inputs in partial power-down states. Pricing below is as of 2026-08-30.
TXE8124-Q1 - 24-Bit Automotive SPI I/O Expander | TI
The Texas Instruments TXE8124-Q1 is an automotive-grade 24-bit SPI bus I/O expander with interrupt output, reset input, and I/O configuration registers, operating from a 1.65V to 5.5V VCC supply and available in a VQFN-32 (RHB) package. An SPI I/O expander is a type of interface IC within the broader semiconductor hierarchy (interface IC -> I/O expander -> logic/integration device) that adds general-purpose parallel input/output pins to a microcontroller or processor using the four-wire Serial Peripheral Interface protocol. It belongs to the same product family as GPIO extenders and port expanders, and is the SPI counterpart to I2C expanders such as the PCX857x family, offering higher speed and deterministic timing. Key features include 24 configurable GPIO channels with individual I/O configuration registers, a dedicated interrupt output (INT) that flags input state changes to the host controller, and a reset input (RST) for rapid recovery of the register map to a known default state. The device supports both standard point-to-point SPI communication and daisy-chaining of multiple devices, allowing several expanders to share a single SPI chip-select in dense I/O designs. Performance scales with supply voltage: according to the Texas Instruments datasheet, the TXE8124-Q1 supports a 10MHz SPI clock when VCC is 3.3V to 5.5V and 5MHz when VCC is 1.65V to 5.5V. This voltage-flexible operation allows direct interfacing with 1.8V, 2.5V, 3.3V, and 5V logic domains without level translation in many systems. Typical applications include automotive body control modules, gateway ECUs, and infotainment boards that need additional GPIO for switches, push-buttons, sensors, LEDs, fans, and relay drivers when the host processor has exhausted its native GPIO. Daisy-chaining suits seat-control modules and door zones where dozens of switches must share one SPI port. When designing with this device, plan daisy-chain timing budgets around the 10MHz maximum clock and account for the added shift-register latency per cascaded device; also verify the interrupt output is polled or serviced before the register state can change again. This page synthesizes verified distributor and manufacturer data with drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet, giving engineers a single citable reference.
TXE8148DGGR - 48-Bit SPI I/O Expander 10MHz | Texas Instruments
The Texas Instruments TXE8148DGGR is a 48-bit SPI bus I/O expander with interrupt output, reset input, and I/O configurable registers, delivering 48 general-purpose I/Os across six 8-bit ports with 10 MHz SPI operation from a 1.65 V to 5.5 V supply in a 56-pin TSSOP package. An I/O expander is a peripheral interface IC that increases the number of input/output pins available to a host microcontroller or processor without changing the host silicon. In the digital system hierarchy it sits between the host bus master (SPI in this case) and the GPIO load, functioning as a bridge in the broader family of interface ICs. I/O expanders such as the TXE8148 offload pin-count-constrained MCUs, allowing one SPI bus to control dozens of additional digital signals with only four host wires plus chip select. Key features include per-I/O programmable open-drain or push-pull outputs, programmable pullup and pulldown resistors, bus-hold latchable inputs, maskable interrupts with an interrupt status register, and a fail-safe operating mode. The device also supports daisy-chaining of multiple TXE8148 units on a single SPI bus, and documentation is available to aid functional safety system design. Technically, the TXE8148 maintains a 10 MHz SPI bus frequency across the entire 1.65 V to 5.5 V VCC range, which is significant for mixed-voltage designs where many expanders derate speed at low supply. The six-port, eight-I/O-per-port register map gives engineers byte-aligned access to all 48 channels, and the reset input provides deterministic recovery of all registers to a known default state after a fault or watchdog event. Typical applications include industrial control panels that need many switch inputs and relay outputs, functionally safe systems requiring documented failure modes, and server or networking backplanes where a processor must monitor dozens of card-present, fault, and status signals. Design consideration: plan your interrupt strategy early - the maskable interrupt and status register let the host poll a single register instead of 48 GPIOs, but interrupt masks must be configured after every reset since registers return to defaults. This page synthesizes distributor pricing, availability, and practical design guidance not found in the manufacturer datasheet alone.