بەرهەمەکان (5,100+)

DS90LV017ATM-NS - 600 Mbps LVDS Driver | Texas Instruments
DS90LV017ATM-NS

DS90LV017ATM-NS - 600 Mbps LVDS Driver | Texas Instruments

The Texas Instruments DS90LV017ATM-NS is a single-channel, current-mode LVDS differential driver designed for data rates exceeding 600 Mbps, or 300 MHz, in an 8-lead SOIC package. It operates from a 3.3 V supply and produces a typical differential output swing of ±355 mV, providing a compact interface for high-speed point-to-point digital links. An LVDS driver is a differential-signaling interface device that converts a low-voltage single-ended logic input into two complementary outputs whose voltage difference carries the data. Current-mode LVDS drivers combine high-speed operation with controlled output current, reduced power dissipation, and low electromagnetic interference. The DS90LV017A family therefore belongs to the hierarchy of interface ICs, line drivers, LVDS transceivers, and semiconductor interface components. The device supports switching rates above 600 Mbps and uses a 3.3 V power supply. Differential skew is typically 0.3 ns and limited to 0.7 ns under specified conditions. Maximum propagation delay is 1.5 ns, helping preserve timing margin in high-speed point-to-point systems. The typical differential output swing of 355 mV and minimized short-circuit fault current support reliable operation while reducing power dissipation at elevated signaling rates. The current-mode architecture keeps dissipation low even at high frequency and avoids the voltage-dependent behavior associated with some older driver approaches. Differential signaling also provides rejection of common-mode noise, while the compact 8-lead SOIC footprint simplifies routing from logic circuitry to a balanced connector or cable interface. The flow-through pin arrangement supports straight-through PCB signal paths and can reduce trace turns on critical high-speed links. Typical uses include clock distribution, high-speed serial data links, industrial control interfaces, instrumentation, test-and-measurement equipment, and embedded systems that transmit one LVDS signal over a controlled point-to-point route. The driver can be paired with a compatible LVDS receiver such as the DS90LV018A, allowing a transmitting endpoint and receiving endpoint to implement a balanced differential link. PCB implementation should preserve a short, continuous differential path with closely matched trace lengths and a continuous ground reference. Decoupling capacitors should be connected directly between the supply and ground pins. The differential output should terminate according to the receiver and transmission-line requirements rather than adding arbitrary resistive loading that could increase edge degradation or reduce signal margin. This page combines the manufacturer's interface specifications with practical package, timing, application, and replacement guidance. It also highlights the distinction between electrically equivalent orderable variants and the conditions under which a same-footprint substitution preserves signal timing, supply requirements, and board-level implementation.

RFQ پەیوەندی
DS90LV017M/NOPB - Single LVDS Driver | Texas Instruments
DS90LV017M/NOPB

DS90LV017M/NOPB - Single LVDS Driver | Texas Instruments

The Texas Instruments DS90LV017M/NOPB is a single-channel LVDS differential line driver supporting data rates in excess of 600 Mbps, or 300 MHz, from a 3.3 V supply in an 8-pin SOIC package. It converts one logic input into a balanced low-voltage differential output for reliable point-to-point communication. An LVDS driver is a line-driver IC within the interface IC and high-speed differential signaling hierarchy. Differential signaling sends complementary currents through two conductors, allowing common-mode noise to be rejected by the receiving device. This makes the DS90LV017M/NOPB suitable for transferring high-speed clock, control, and data signals across cables or PCB traces where signal integrity is important. The device uses a current-mode architecture to limit power dissipation at high operating frequencies and reduce short-circuit fault current. Its operating supply range is 3 V to 3.6 V. The verified manufacturer information identifies the device as a 1/0 line driver, meaning it provides one differential driver and no integrated receiver. Its differential output is intended for systems operating at data rates above 600 Mbps. The SOIC-8 package provides a conventional surface-mount implementation and supports tube packaging according to the component listing. The device is identified as a lead-free SOIC-8 part and is associated with EIA-644-A and TIA-644-A low-voltage differential signaling specifications. Its commercial operating-temperature information must be confirmed against the exact ordering code before deployment in temperature-sensitive equipment. Typical uses include high-speed point-to-point links, clock distribution, industrial control interfaces, test equipment, and embedded systems that convert a low-voltage CMOS input into an LVDS differential output. In each case, the receiver must support compatible LVDS levels, and the interconnect must be routed as a controlled-impedance differential pair. PCB implementation should minimize the distance between the driver and the connector, maintain closely matched differential trace lengths, and provide a continuous reference plane beneath the pair. Keep the differential traces away from switching nodes and noisy return-current paths because trace geometry and return-path discontinuity can degrade signal-integrity performance even when the driver itself operates within its stated limits. This product record combines the device function, verified electrical and packaging characteristics, available same-family alternatives, and practical PCB guidance. It also highlights where exact pin assignments, temperature limits, lifecycle details, and qualified drop-in replacements should be confirmed in the manufacturer datasheet before a production release.

RFQ پەیوەندی
DS90LV017MX - 155Mbps LVDS Driver | Texas Instruments
DS90LV017MX

DS90LV017MX - 155Mbps LVDS Driver | Texas Instruments

The Texas Instruments DS90LV017MX is a single-channel LVDS differential driver with a 155 Mbps data rate, 3 V to 3.6 V supply range, and an 8-SOIC package. It converts one CMOS input into a balanced LVDS differential output for high-speed point-to-point communication links. The device is specified for 0°C to 70°C operation and is packaged in an 8-pin SOIC, making it suitable for industrial and commercial equipment requiring a compact differential line driver. An LVDS differential driver is an interface IC that transmits data across a balanced copper connection. LVDS, or Low-Voltage Differential Signaling, belongs to the interface IC family and uses complementary differential signals to improve noise immunity and reduce electromagnetic interference compared with single-ended logic. The DS90LV017MX provides one driver channel in a small 8-SOIC package for systems that need a single high-speed differential output. Key features include one LVDS driver channel, a 155 Mbps maximum data rate, operation from 3 V to 3.6 V, and a 0°C to 70°C operating-temperature range. The reported operating voltage allows the driver to be used with 3.3 V system rails, while the LVDS output supports low-voltage, high-speed signaling across suitable board-level or balanced-cable interconnects. The package is specified as 8-SOIC, with a 0.154 inch, 3.90 mm body width. The DS90LV017MX is intended for point-to-point links where a transmitter must launch a compliant differential signal into a controlled impedance interconnect. Because LVDS relies on balanced signaling, the receiving device, trace geometry, connector, and terminations determine whether the intended signal integrity and data-rate margins are achieved. The driver is therefore best suited to applications where the complete channel has been characterized rather than relying on the IC alone. Typical applications include industrial control links, test and measurement equipment, computer peripherals, point-to-point backplanes, and embedded communication interfaces. Its single-driver configuration makes it useful when a system needs one LVDS transmit path and requires a small package. The 0°C to 70°C temperature range supports commercial and industrial environments within that specified range. When designing around the DS90LV017MX, verify the input amplitude, supply sequencing, output termination, differential trace impedance, and receiver compatibility in the complete channel. The 3 V to 3.6 V supply range requires a valid 3.3 V rail, and the 0°C to 70°C rating must be checked against the equipment enclosure temperature. This product page consolidates distributor availability, package information, operating limits, verified cross-reference results, and practical selection guidance into one engineering-oriented reference for the DS90LV017MX LVDS driver.

RFQ پەیوەندی
DS90LV018ATM - 400 Mbps LVDS Receiver | Texas Instruments
DS90LV018ATM

DS90LV018ATM - 400 Mbps LVDS Receiver | Texas Instruments

The Texas Instruments DS90LV018ATM is a 3 V LVDS single CMOS differential line receiver capable of data rates above 400 Mbps, equivalent to 200 MHz, in an 8-pin SOIC package. It accepts a typical 350 mV differential LVDS input and translates it to 3 V CMOS logic levels. The receiver is designed for low power dissipation, low noise, high data rates, and robust operation in point-to-point balanced data links. An LVDS receiver is an interface IC that recovers a digital signal carried by two low-voltage differential conductors. LVDS belongs to the differential data-interface hierarchy, where the voltage difference between the pair carries the information while common-mode voltage rejection helps limit noise pickup. The DS90LV018A therefore belongs to the broader interface IC category, where it sits between a physical data link and the CMOS logic, processor, serializer, or test equipment receiving the recovered data. The device supports data rates in excess of 400 Mbps, or 200 MHz, while maintaining a typical differential input sensitivity of 350 mV. According to the Texas Instruments DS90LV018A datasheet, the receiver converts the differential LVDS input into 3 V CMOS output levels. It also supports open, shorted, and 100-ohm terminated-input fail-safe conditions, with the receiver output remaining HIGH in every specified fail-safe condition. The flow-through pin arrangement simplifies routing between the LVDS input connector or transceiver and the receiving digital circuitry. Its CMOS interface allows direct connection to compatible TTL or CMOS logic domains when voltage and timing requirements are satisfied. The architecture is intended for systems needing low power consumption and low noise without the complexity of a general-purpose differential receiver with programmable controls. The 8-pin SOIC outline also supports conventional surface-mount PCB assembly. Typical uses include industrial control links, test and measurement equipment, computer peripherals, video or imaging interfaces, and communication equipment operating over balanced cables. The receiver is especially useful where the transmitter produces an LVDS signal over a cable or PCB trace and the destination requires a single-ended CMOS result. System timing should still be evaluated across the complete transmitter, channel, receiver, and downstream logic path. When laying out the receiver, place input and output decoupling capacitors close to their associated power pins and keep the differential route compact, symmetrical, and away from noisy switching nodes. Use controlled-impedance routing where the interconnect behaves as a transmission line, and follow the datasheet's recommended termination arrangement for the source and receiver configuration. Verify signal integrity at the target data rate rather than relying only on a maximum-rate headline specification. This product page combines the manufacturer's core operating specifications, same-package replacement guidance, application-specific engineering guidance, and a parameter-by-parameter comparison. It is intended to shorten receiver selection while preserving the package, interface, and fail-safe details that determine whether an LVDS link can be deployed reliably.

RFQ پەیوەندی
DS90LV019TM - 3.3V/5V LVDS Transceiver | Texas Instruments
DS90LV019TM

DS90LV019TM - 3.3V/5V LVDS Transceiver | Texas Instruments

The Texas Instruments DS90LV019TM is a 3.3 V or 5 V low-voltage differential signaling transceiver containing one differential driver and one differential receiver in a 14-pin SOIC package. It supports data rates up to 100 Mbps and accepts TTL/CMOS-compatible driver inputs while providing a CMOS-compatible receiver output. The device is intended for high-speed, low-power point-to-point interconnects where differential signaling improves noise immunity and reduces EMI. An LVDS transceiver is an interface IC that converts a single-ended logic signal into a low-voltage differential pair on the transmit side and converts a received differential pair back into a single-ended logic signal on the receive side. In the signal-chain hierarchy, DS90LV019TM is an LVDS interface transceiver, belonging to the broader interface-IC and data-communications semiconductor categories. Its differential signaling is associated with the EIA-644-A and TIA-644-A technologies identified in the verified component data. Key features include independent operation of the driver and receiver, support for both 3.3 V and 5 V supplies, and a 3.5 mA LVDS output loop current. The 14-pin SOIC package uses a flow-through pin arrangement that permits short PCB routing between device pins and an external connector. A maximum data rate of 100 Mbps makes the device suitable for moderate-speed point-to-point links rather than very high-speed multimode channels. The architecture uses a current-mode differential driver to maintain controlled output current while transferring data across a balanced connection. Because the two transmission lines carry complementary signals, external circuitry reconstructs the logic state from their voltage difference. This approach can reduce sensitivity to common-mode noise relative to an unbalanced single-ended link, provided the receiver termination, connector, and cable geometry satisfy the interface requirements. Typical uses include industrial control links, test and measurement equipment, computer peripherals, video or display interconnects, and embedded systems that need a compact LVDS point-to-point interface. Because the driver and receiver are independent, a board can transmit and receive over separate balanced pairs. The 14-pin SOIC package is also suitable for conventional surface-mount PCB assembly where sufficient copper and solder mask clearance are available. Designers should preserve the flow-through routing advantage and keep LVDS traces short, properly terminated, and referenced to a continuous ground plane. Input and output logic levels must remain compatible with the selected 3.3 V or 5 V supply. Because the supplied excerpts do not provide a verified pin-number-to-pin-name table, the pinout is intentionally left unpopulated rather than presenting inferred connections as authoritative data. This page combines verified manufacturer and distributor information, package details, interface characteristics, application guidance, and strict drop-in equivalence analysis. It also distinguishes electrically similar parts that use a different package and therefore cannot be treated as true PCB drop-in replacements.

RFQ پەیوەندی
DS90LV027AHM - 600Mbps Dual LVDS Driver | TI
DS90LV027AHM

DS90LV027AHM - 600Mbps Dual LVDS Driver | TI

The Texas Instruments DS90LV027AHM is a dual LVDS differential driver optimized for high-data-rate and low-power applications, supporting data rates in excess of 600 Mbps (300 MHz) in an 8-pin SOIC package. It provides two driver channels, operates from a 3 V to 3.6 V supply, and uses a current-mode architecture to limit power dissipation at high frequency. The high-temperature grade supports operation from -40°C to +125°C. An LVDS driver is a line-driver interface that converts low-voltage digital signals into a differential low-voltage signal for reliable, high-speed transmission over balanced interconnects. Within the signal-chain hierarchy, the DS90LV027AHM belongs to the LVDS interface-driver category, uses Low Voltage Differential Signaling, and provides a current-mode differential output suitable for clock and data links. The device’s key features include support for data rates above 600 Mbps, a typical output swing of 360 mV, and low differential output swing for reduced EMI. Its flow-through pin arrangement simplifies PCB routing by allowing signals to pass through the device without changing direction. The driver architecture also provides short-circuit fault-current limiting, supporting fault-tolerant operation in cables and connectorized backplanes. Two independent differential outputs allow one package to drive two LVDS channels, reducing board area for parallel clock and data links. Because the outputs are current-mode devices, their power consumption remains low at high operating frequencies. The 3 V to 3.6 V supply range integrates directly with common low-voltage digital systems, while the high-temperature rating supports applications with extended ambient-temperature requirements. Typical uses include clock distribution, high-speed data transmission, industrial control links, test equipment, backplanes, and industrial systems requiring more than 600 Mbps operation. The DS90LV027AHM can be paired with the DS90LV028AH dual line receiver to form a complete differential transmission path when signal integrity and protocol requirements are compatible. PCB implementation should preserve the flow-through signal path, use a continuous ground reference plane, and minimize stubs on differential traces. Keep the input and output branches short, maintain closely matched trace geometry, and follow the manufacturer’s recommended supply bypassing and controlled-impedance layout practices. This page combines the manufacturer’s device characteristics, verified part identification, package information, practical interface-design guidance, and a strict assessment of drop-in replacement options to support faster engineering selection and sourcing.

RFQ پەیوەندی
DS90LV027M - Dual 600 Mbps LVDS Driver | Texas Instruments
DS90LV027M

DS90LV027M - Dual 600 Mbps LVDS Driver | Texas Instruments

Texas Instruments DS90LV027M is a dual LVDS differential line driver supporting data rates in excess of 600 Mbps, equivalent to a 300 MHz serialized data rate, in an 8-lead SOIC package. The device uses a 3.3 V supply, implements a low-power current-mode architecture, and minimizes short-circuit fault current. Its two differential outputs are intended for point-to-point, low-voltage, differential signaling over controlled-impedance interconnects. An LVDS driver is a high-speed interface device that converts low-voltage digital inputs into balanced differential outputs. LVDS belongs to the differential line-driver hierarchy within interface ICs, where it supports high data rates while limiting signal amplitude, crosstalk, and ground-reference sensitivity. The DS90LV027M is therefore positioned between general-purpose logic drivers and higher-power physical-layer drivers for links requiring a compact, low-voltage solution. Key characteristics include two LVDS outputs, operation from a 3.0 V to 3.6 V supply, a data rate above 600 Mbps, and a nominal 3.3 V operating point. The current-mode implementation is significant because it allows power dissipation to remain comparatively low at high operating frequencies. Reduced fault current also improves robustness when an output is shorted. According to the manufacturer product information, the package uses a flow-through pin arrangement intended to simplify PCB routing. The device is suited to high-speed point-to-point links, including display and panel interfaces, industrial control links, communications equipment, and embedded digital systems. The dual-channel architecture lets one package drive two independent differential channels, reducing component count and simplifying synchronization when both channels carry related data. PCB design should preserve controlled differential impedance and minimize the distance between each output and its receiver. Input and output return paths should be referenced consistently, and unused inputs must not be left floating. Because the verified source data does not provide the complete numbered pin assignment, termination guidance, or electrical-characteristic tables, those engineering details should be confirmed against the manufacturer datasheet before layout release. This page consolidates the verified manufacturer description, distributor packaging information, device parameters, and practical replacement guidance. It also distinguishes documented ordering-code differences from a genuine cross-brand drop-in claim, helping engineers make a sourcing decision without confusing functional similarity with PCB compatibility.

RFQ پەیوەندی
DS90LV027M/NOPB - 155Mbps Dual LVDS Driver | Texas Instruments
DS90LV027M/NOPB

DS90LV027M/NOPB - 155Mbps Dual LVDS Driver | Texas Instruments

Texas Instruments DS90LV027M/NOPB is a dual low-voltage differential signaling (LVDS) driver supporting 155 Mbps in an 8-lead SOIC package. The device provides two differential outputs, operates from a 3.3 V supply, and combines a CMOS implementation with current-mode output architecture. Its 0.45 V differential output voltage is suited to low-power, high-speed point-to-point interfaces. An LVDS driver is a high-speed interface device that converts low-voltage logic signals into balanced differential signals. This differential signaling method belongs to the broader interface IC hierarchy and reduces susceptibility to common-mode noise compared with single-ended transmission. The DS90LV027M/NOPB is intended for designs that require low power dissipation, controlled output current, and minimized short-circuit fault current. The dual-driver architecture provides two independent channels in one package, reducing board area when two LVDS links are required. Its current-mode output keeps dissipation low even at high operating frequencies, while the short-circuit protection characteristic limits fault current. The flow-through pin arrangement also supports straightforward routing of differential pairs and simplifies PCB layout compared with packages that require inputs and outputs on opposing sides. Operation across a -40°C to +85°C temperature range makes the device appropriate for industrial and commercial equipment. The 8-lead SOIC package is available in a small-board footprint and uses a standard pin arrangement. At 3.3 V supply voltage, the device combines a 0.45 V differential output with data-rate capability listed for the family in excess of 600 Mbps, allowing it to address both established 155 Mbps links and higher-speed LVDS signaling requirements. Typical uses include industrial control links, test and measurement equipment, computer interfaces, video and display links, and communication equipment that transfers data between circuit boards. The dual-channel configuration is especially useful for clock-plus-data, serial-backplane, point-to-point, and parallel-to-serial interface arrangements where cable-length and common-mode-noise performance are important. PCB implementation should preserve the flow-through routing of each differential pair and provide a continuous return path beneath the traces. Keep the two conductors of each pair at a consistent width and spacing, minimize stubs, and place any required termination close to the receiving device. Decoupling capacitors should be connected directly to the supply and ground pins with short, low-inductance paths. This product page organizes the device specifications, verified package details, pricing context, drop-in ordering variants, and application guidance into one engineering reference. It also distinguishes the electrically equivalent order codes from the physical packing options so designers can select the correct manufacturer part number without changing the PCB footprint.

RFQ پەیوەندی
DS90LV027MX - Dual 600Mbps LVDS Driver | Texas Instruments
DS90LV027MX

DS90LV027MX - Dual 600Mbps LVDS Driver | Texas Instruments

Texas Instruments DS90LV027MX is a dual CMOS LVDS differential driver optimized for high-data-rate, low-power signal transmission. It supports data rates in excess of 600 Mbps, operates from a nominal 3.3 V supply, and is packaged in an 8-lead SOIC. Each channel uses a current-mode differential driver, while the device’s flow-through pin arrangement simplifies high-speed PCB routing. According to the Texas Instruments product page, the driver maintains low power dissipation at high frequency and minimizes short-circuit fault current. Its differential outputs typically swing about 340 mV, providing low EMI while transferring clock and data signals. The DS90LV027MX is therefore positioned between general-purpose logic interfaces and the broader LVDS interface-IC category, where differential signaling, controlled output current, and low-noise operation are central requirements. An LVDS driver is a line and bus driver that converts a low-voltage CMOS logic input into a balanced differential output. Because LVDS transmits information as the voltage difference between two conductors, it can support high data rates while reducing sensitivity to common-mode noise and limiting electromagnetic emissions. The DS90LV027MX includes two independent differential drivers, allowing clock, data, control, or serial-interface signals to be transmitted in parallel. Its dual-channel architecture increases routing flexibility while conserving board area compared with two separate single-channel devices. The manufacturer describes the DS90LV027 as a current-mode driver optimized for high-data-rate and low-power operation. This architecture helps power dissipation remain low as operating frequency increases and also reduces the short-circuit fault current available from the outputs. Differential output swing is typically 340 mV, which supports LVDS-compatible receivers and limits output voltage excursions. The 8-lead SOIC package uses a flow-through layout intended to make PCB layout easier, particularly when traces must pass through or around the device on high-speed digital boards. The verified device information identifies DS90LV027MX as a 2/0 LVDS driver in an 8-SOIC package. The related lead-free DS90LV027MX/NOPB listing identifies a 3.0 V to 3.6 V supply range, while Mouser lists the commercial-temperature variant at 0°C to 70°C. The DS90LV027 family is designed for data rates in excess of 600 Mbps, equivalent to more than 300 MHz of serialized information according to the family description. The current-mode implementation and controlled differential swing help balance high throughput, power consumption, and EMI control. Typical uses include clock distribution, parallel-to-serial data links, industrial-control interfaces, test and measurement equipment, video timing links, and communications systems that transmit high-speed clock or data over balanced lines. Because the DS90LV027MX provides two differential outputs, a board designer can use one channel for a clock and another for data, or deploy two independent data streams. In each case, the receiver, cable, connector, and PCB geometry must be designed consistently with LVDS signal integrity requirements. The most important layout consideration is to preserve controlled differential impedance and minimize the distance over which the two traces of a pair are separated. Place decoupling close to the supply pins, route the differential pair as a tightly coupled pair, and avoid unnecessary stubs or test-point discontinuities. The 8-lead SOIC footprint is easy to source, but package parasitics, connector transitions, and imperfect pair geometry can still reduce the practical benefit of the device’s high supported data rate. This product page combines the verified Texas Instruments and distributor information with package, application, selection, and design guidance. It also distinguishes confirmed ordering variants from unsupported substitutes and identifies every parameter that still requires confirmation from the manufacturer datasheet or distributor record.

RFQ پەیوەندی
DS90LV028AHM - 3V LVDS Dual Differential Line Receiver | Texas Instruments
DS90LV028AHM

DS90LV028AHM - 3V LVDS Dual Differential Line Receiver | Texas Instruments

The Texas Instruments DS90LV028AHM is a dual CMOS differential line receiver designed for ultra-low power dissipation, low noise and high data rates, housed in an 8-pin SOIC package. It accepts low-voltage differential signals of 350 mV typical and translates them to CMOS/TTL logic levels, supporting data rates in excess of 400 Mbps (200 MHz) using Low Voltage Differential Signaling (LVDS) technology. An LVDS receiver is a type of line receiver that converts a small-amplitude differential pair into a single-ended digital output. Differential signaling belongs to the broader hierarchy of interface ICs, because common-mode rejection, equalization and low swing allow reliable transfer over longer cables or PCB traces where single-ended signals would be corrupted by noise. The DS90LV028AH is the receiving half of a point-to-point link; the matching line driver is the DS90LV027A family. Key characteristics of the DS90LV028AHM include support for 400 Mbps (200 MHz) data rates, a 3.3 V supply rail, a flow-through pin arrangement that simplifies point-to-point PCB routing, and a high-temperature grade rated from -40 C to +85 C for industrial and automotive-adjacent environments. The dual-channel architecture lets one package carry two independent LVDS links, reducing board area in multi-channel point-to-point systems. Internally the receiver uses CMOS logic with differential input stages, giving low power dissipation compared with PECL or ECL receivers while retaining low noise. Because LVDS receivers present a high-impedance differential input, the part draws minimal DC current from the driver, which increases the achievable link distance and reduces connector and cable loading. The flow-through layout places input pins opposite output pins so the device can sit in-line on a board edge or cable-riser interface. Typical applications include backplane and board-to-board point-to-point links, industrial and telecom backplanes, video and imaging data paths, and instrumentation or test equipment that needs high-rate transfer over a few metres of twisted pair. It is also used where a high-power PECL/ECL receiver would waste power, since the LVDS approach delivers the same throughput at a fraction of the power. When designing with this receiver, keep differential trace pairs tightly coupled with matched length and controlled impedance, and provide solid ground-plane return under the pair. The 3.3 V supply should be decoupled close to the VCC pin. Because the part is a high-temperature grade variant, verify your system ambient and the associated operating limits against the datasheet before using it in elevated-temperature locations. This page brings together the manufacturer specifications, drop-in ordering-code options for the same die, and practical layout and signal-integrity guidance that engineers normally have to piece together from several separate documents.

RFQ پەیوەندی
DS90LV028ATM - Dual 400 Mbps LVDS Receiver | Texas Instruments
DS90LV028ATM

DS90LV028ATM - Dual 400 Mbps LVDS Receiver | Texas Instruments

Texas Instruments DS90LV028ATM is a dual CMOS differential line receiver for Low Voltage Differential Signaling (LVDS) data links, supporting data rates in excess of 400 Mbps (200 MHz) in an 8-pin SOIC package. The receiver accepts a typical differential input voltage of 350 mV and converts each LVDS input into a CMOS-compatible logic output. Its dual-channel architecture allows one package to receive two independent low-voltage differential signals. An LVDS receiver is an interface IC within the broader line-receiver and interface-IC hierarchy. LVDS is a differential signaling technology in which data is transmitted as the voltage difference between two complementary conductors. That architecture provides useful noise immunity for high-speed links, while the receiver converts the small differential signal into a single-ended CMOS output that can be processed by digital logic, a controller, or a field-programmable gate array. According to the Texas Instruments DS90LV028A product page, the device is designed for applications requiring ultra-low power dissipation, low noise, and high data rates. The verified technical summary identifies a maximum data rate in excess of 400 Mbps, equivalent to a 200 MHz parallel data rate. The related distributor data also identifies a 3 V supply class, a 1.5 ns receiver performance figure, and approximately 9 mA of operating current, although the exact test conditions are not included in the supplied excerpts. The DS90LV028A family provides two independent receiver channels, making it useful in point-to-point industrial links, test and measurement equipment, instrumentation, and backplane communication. The 8-pin SOIC footprint simplifies assembly in designs that already use conventional surface-mount packages. Because LVDS is a differential interface, each receiver channel requires a matched differential input and appropriate cable or board-level termination. Designers should preserve the receiver's common-mode operating limits, provide the specified termination network, and maintain a controlled return path between the transmitter and receiver. Differential routing on the printed circuit board should minimize impedance discontinuities and keep the pair length-matched. The receiver should also be evaluated for fail-safe behavior when the cable is open, shorted, or terminated because those conditions affect receiver metastability and output state. This product page consolidates the verified manufacturer specifications, distributor identifiers, package information, application guidance, and substitution constraints for DS90LV028ATM. It also distinguishes a true pin-compatible replacement from similar LVDS receivers that require a different pinout, circuit modification, or data-rate tradeoff.

RFQ پەیوەندی
DS90LV028ATM-TI - 400 Mbps Dual LVDS Receiver | TI
DS90LV028ATM-TI

DS90LV028ATM-TI - 400 Mbps Dual LVDS Receiver | TI

The Texas Instruments DS90LV028ATM-TI is a dual CMOS differential line receiver designed for low-power, low-noise, high-speed LVDS communication. The device supports data rates in excess of 400 Mbps, equivalent to 200 MHz, and accepts differential input signals with a typical amplitude of 350 mV. The DS90LV028ATM-TI is supplied in an 8-pin SOIC package. An LVDS receiver is a high-speed interface component that converts a small-amplitude differential signal into a complementary CMOS output. Differential signaling rejects common-mode noise and is used when signal integrity, clock recovery, and data-transfer rate are more important than minimizing the number of interconnects. In the broader electronics hierarchy, the DS90LV028ATM-TI belongs to the interface IC and line-receiver category rather than being a general-purpose logic device. The receiver is intended for applications requiring ultra-low power dissipation, low noise, and high data rates. Its differential input architecture supports reliable reception over longer board or cable distances than ordinary single-ended CMOS interfaces. Because it is a dual receiver, one device can receive two independent LVDS channels, making it suitable for parallel data links, point-to-point interfaces, and clock-and-data distribution systems. The 8-pin SOIC package provides a compact surface-mount implementation for industrial, communications, and embedded systems. The receiver converts differential LVDS inputs into CMOS-compatible outputs, allowing the downstream logic to operate with ordinary digital input thresholds. The 400-Mbps capability makes the device relevant to high-speed control links, backplanes, instrumentation, and embedded processor communication where a standard low-speed transceiver would be insufficient. The DS90LV028ATM-TI should be used when the design requires a dual LVDS input stage and a 3.3 V-class CMOS interface. Layout should preserve controlled differential impedance, minimize stub length, and provide a continuous return path beneath the pair. Input and output decoupling should be placed close to the relevant pins. The component is not a power IC, so SOA information is not applicable. This product page combines the device function, package characteristics, verified manufacturer information, drop-in replacement guidance, comparison data, and practical PCB design notes for engineers evaluating the DS90LV028ATM-TI.

RFQ پەیوەندی
DS90LV031ATM - 3V Quad LVDS Line Driver | Texas Instruments
DS90LV031ATM

DS90LV031ATM - 3V Quad LVDS Line Driver | Texas Instruments

The Texas Instruments DS90LV031ATM is a 3V quad CMOS differential line driver designed for low-power, high-speed LVDS communication links. It supports data rates in excess of 400 Mbps, equivalent to a 200 MHz clock rate, and translates low-voltage LVTTL or LVCMOS inputs into four low-voltage differential outputs. The device is packaged in a 16-pin SOIC. An LVDS line driver is a differential interface component that converts a single-ended CMOS logic signal into two complementary low-voltage outputs. This differential signaling method reduces common-mode noise, lowers electromagnetic emissions, and improves signal integrity over longer point-to-point interconnects. In the broader component hierarchy, the DS90LV031A belongs to the line-driver family, interface IC category, and high-speed digital communication ecosystem. The principal features of the DS90LV031ATM include four differential drivers, operation from a 3V supply, support for rates above 400 Mbps, and common enable controls for tri-state output operation. LVTTL and LVCMOS input compatibility allows the device to interface directly with common digital logic families. The common EN and EN-bar controls support active-high or active-low output enable management while coordinating all four channels. The DS90LV031A architecture provides a practical alternative to high-power pseudo-ECL devices in point-to-point interface systems. Differential output signaling improves noise immunity by rejecting noise that appears equally on both output conductors. Its CMOS implementation is intended for systems where data throughput matters more than the very short reach and low logic levels associated with conventional ECL devices. Typical uses include clock distribution, parallel data links, backplane communication, telecommunications equipment, industrial control systems, and test and measurement instruments. The companion DS90LV032A receiver provides the corresponding four-channel differential receiving function for complete point-to-point links. PCB layout is critical when operating at LVDS rates. Use controlled-impedance routing, keep differential pairs closely coupled, minimize stub lengths, and place any termination components close to the receiving device. Confirm the output voltage, supply tolerance, propagation delay, and enable timing in the manufacturer datasheet before releasing a high-volume design. This page organizes the device characteristics, pin and package requirements, application guidance, and verified drop-in alternatives into one engineering reference. It also highlights practical distinctions between the standard, lead-free, and related DS90LV031A ordering codes so that compatibility can be checked before a PCB respin or production release.

RFQ پەیوەندی
DS90LV031ATMTC - 3.3V Quad LVDS Driver | Texas Instruments
DS90LV031ATMTC

DS90LV031ATMTC - 3.3V Quad LVDS Driver | Texas Instruments

The Texas Instruments DS90LV031ATMTC is a 3.3 V quad CMOS differential line driver supporting data rates above 400 Mbps and clock frequencies above 200 MHz through Low Voltage Differential Signaling (LVDS). The device accepts LVTTL or LVCMOS inputs, provides four differential LVDS outputs, and is packaged in a 16-pin TSSOP package. An LVDS line driver is a high-speed interface device that converts low-voltage single-ended logic signals into low-voltage differential signals. This differential signaling method supports the LVDS interface layer within point-to-point data links. Compared with conventional single-ended CMOS, differential LVDS improves noise immunity and helps preserve signal integrity over longer cable or board traces. The DS90LV031A family provides four parallel driver channels in one package. Inputs accept LVTTL or LVCMOS levels, while each output produces a differential LVDS signal with a nominal differential output magnitude of 350 mV. The outputs support tri-state operation, and common enable inputs allow active-low or active-high control of all four channels. Its low-power CMOS implementation makes the device suitable for systems that need high data throughput without the higher power consumption associated with older high-speed pseudo-ECL interface devices. The quad-channel architecture also reduces the number of interface packages and driver ICs required on a multi-lane board. Typical uses include point-to-point links between FPGAs, ASICs, DSPs, and test equipment; industrial data acquisition systems; and communications equipment carrying multiple high-speed differential channels. The device can also serve as the transmitting half of a link paired with the DS90LV032A receiver family. PCB implementation requires careful differential routing, short traces, a continuous reference plane, and symmetrical signal geometry. The output differential impedance must match the selected board media and termination network, while input and enable timing must be checked for the target data rate. This page consolidates the device function, lifecycle status, package information, comparison parameters, and replacement guidance to support schematic review, PCB compatibility checks, and sourcing decisions for legacy LVDS designs.

RFQ پەیوەندی
DS90LV032ATM - 400 Mbps 4-Channel LVDS Receiver | Texas Instruments
DS90LV032ATM

DS90LV032ATM - 400 Mbps 4-Channel LVDS Receiver | Texas Instruments

Texas Instruments DS90LV032ATM is a 3 V LVDS quad differential line receiver designed for high-speed point-to-point data links. It converts four low-voltage differential input pairs into 3 V CMOS outputs while supporting data rates in excess of 400 Mbps, equivalent to a 200 MHz clock rate. The device is packaged in a 16-pin narrow SOIC and is identified by the DS90LV032A family designation. An LVDS receiver is an interface circuit that recovers a digital signal from a small differential voltage carried over a balanced pair of conductors. LVDS belongs to the broader class of differential line receivers and interface ICs used to move high-speed data reliably between boards, backplanes, and rack-mounted systems. The DS90LV032A accepts low-voltage differential signals, typically 350 mV, and translates them into CMOS-compatible logic levels for downstream digital circuits. Key features of the DS90LV032ATM include four independent receiver channels, data-rate operation above 400 Mbps, and a single 3 V supply. The receiver architecture is suited to low-power consumption and high-speed digital communication. The 16-pin SOIC package allows direct comparison with other 16-pin LVDS receiver families, although input and output pin functions should always be verified against the specific manufacturer datasheet before substitution. The DS90LV032A is commonly used in point-to-point LVDS links, test and measurement equipment, industrial control systems, and digital backplanes. Its differential inputs help reject common-mode noise, while the CMOS outputs connect directly to FPGA, ASIC, or other digital logic inputs. The device supports data rates beyond 400 Mbps, making it appropriate for high-speed clock, control, and data-transfer connections. Designers should pay attention to differential pair routing, controlled-impedance transmission lines, connector and via geometry, and the receiver supply decoupling. The TI DS90LV032A datasheet is the authoritative source for input thresholds, propagation delay, supply-current behavior, and absolute maximum ratings. The manufacturer product page identifies the DS90LV032A as an active 3 V LVDS quad CMOS differential line receiver, while the DS90LV032ATM orderable designation is listed in a 16-pin SOIC package. This page combines the manufacturer datasheet, product-page information, distributor records, and cross-reference results for the DS90LV032ATM. It also provides application guidance, package-level design notes, comparison parameters, and drop-in alternative candidates for engineers evaluating an LVDS receiver redesign or second-source plan.

RFQ پەیوەندی
DS90LV032ATMTC - 400 Mbps Quad LVDS Receiver | Texas Instruments
DS90LV032ATMTC

DS90LV032ATMTC - 400 Mbps Quad LVDS Receiver | Texas Instruments

The Texas Instruments DS90LV032ATMTC is a four-channel, 3-V LVDS differential line receiver that converts four low-voltage differential inputs into 3-V CMOS outputs. It supports data rates in excess of 400 Mbps, equivalent to a 200 MHz data clock, and accepts a typical differential input signal of 350 mV. The device is packaged in a 16-pin TSSOP for high-speed point-to-point digital-interface applications. An LVDS receiver is an interface circuit that detects the voltage difference between a complementary pair of low-voltage differential signals. The DS90LV032A family belongs to the hierarchy of differential line receivers, digital interface ICs, and semiconductors. Compared with older PECL or ECL interfaces, LVDS provides a lower-voltage differential transport method with low power dissipation while supporting high-speed data transfer over balanced connections. The receiver architecture supports four independent LVDS channels, low-power operation, and 3-V CMOS-compatible outputs. Its differential input threshold is centered around a typical 350 mV signal, while its operating speed exceeds 400 Mbps. These characteristics make the device useful when a system must recover digital data from balanced cables, backplanes, or point-to-point links without converting the physical layer to single-ended logic internally. The DS90LV032A is designed to work with the DS90LV031A companion line driver as an alternative to higher-power PECL or ECL interface solutions. Its quad-channel organization reduces the number of interface devices needed when several differential links are required. Because LVDS is differential, the implementation must preserve controlled impedance, symmetrical routing, and proper termination to avoid common-mode noise and timing degradation. Typical applications include industrial control links, high-speed backplanes, video and data acquisition systems, instrumentation, test and measurement equipment, and point-to-point transfers between circuit boards. The receiver is most appropriate where several high-speed links must operate from a 3-V supply while maintaining a compact 16-pin footprint. PCB layout is critical in a 400-Mbps design. Place the receiver close to the connector or transmission-line endpoint, provide a continuous reference plane, match differential pair geometry, and avoid stubs. Verify signal and ground return paths carefully because small impedance discontinuities can create reflections that degrade receiver performance even when the logic itself operates correctly. This page combines the manufacturer's device description with package information, source links, replacement analysis, and practical interface-layout guidance. It is designed to help engineers determine whether the DS90LV032ATMTC fits an existing 16-pin TSSOP LVDS design and how to integrate it into a high-speed, low-power differential interface.

RFQ پەیوەندی
DS90LV032ATMX - 400 Mbps Quad LVDS Receiver | Texas Instruments
DS90LV032ATMX

DS90LV032ATMX - 400 Mbps Quad LVDS Receiver | Texas Instruments

Texas Instruments DS90LV032ATMX is a quad CMOS differential line receiver designed for high-speed LVDS links, supporting data rates in excess of 400 Mbps at 200 MHz in a 16-pin SOIC package. It accepts typical 350 mV differential input signals and converts them into 3 V CMOS outputs, making it suitable for point-to-point interfaces requiring low power consumption and high data throughput. An LVDS receiver is an interface circuit that detects the voltage difference between two complementary low-voltage differential signals. This differential detection improves noise immunity and allows reliable communication over balanced interconnects. The DS90LV032A belongs to the broader LVDS interface IC family, where a quad receiver provides four independent differential input channels and four CMOS output channels. The device supports signaling rates above 400 Mbps and uses a 3.3 V supply. Its CMOS outputs are designed for use with digital logic operating at compatible voltage levels. Four receivers are integrated in one package, reducing component count and board area compared with discrete single-channel receiver implementations. The 16-SOIC package is suitable for conventional surface-mount assembly. The differential architecture is important in systems where common-mode voltage and externally coupled noise could disturb a single-ended signal path. A 350 mV typical differential input is evaluated relative to the complementary pair, so the receiver can distinguish the intended data transition from noise common to both conductors. The resulting CMOS signals can be routed into counters, controllers, FPGAs, or other digital processing blocks. Typical applications include high-speed point-to-point data links, communications equipment, industrial control systems, test and measurement instruments, and backplanes requiring a low-power differential receiver. The device can also work with a compatible driver such as the DS90LV031A when both ends of the link use the same LVDS signaling convention. PCB implementation should preserve the balanced geometry of each LVDS pair and provide a solid ground reference. Place the receiver close to the connector or transceiver when trace length is short, while observing the manufacturer’s input and supply-layout guidance when routing across a larger board. This product page combines manufacturer electrical characteristics, package details, application guidance, and drop-in alternative analysis to support component selection and PCB planning. For obsolete inventory, current availability, and project-specific sourcing, use the Request a Quote form on this page.

RFQ پەیوەندی
DS90LV032AW-MLS - 400Mbps Quad LVDS Receiver | Texas Instruments
DS90LV032AW-MLS

DS90LV032AW-MLS - 400Mbps Quad LVDS Receiver | Texas Instruments

The Texas Instruments DS90LV032AW-MLS is a 3 V LVDS quad CMOS differential line receiver supporting data rates above 400 Mbps, equivalent to a 200 MHz switching rate, in a 16-pin CFP (NAD) package. It accepts four differential LVDS inputs and converts them to 3 V CMOS outputs, with a typical differential input voltage of 350 mV and an operating temperature range from -55°C to +85°C. An LVDS receiver is an interface circuit that detects a small differential voltage across a balanced signal pair and converts it into a logic-level output. LVDS belongs to the differential data-interface hierarchy, where low-amplitude, noise-resistant signaling supports reliable high-speed data transfer over circuit-board interconnects. The DS90LV032A family therefore belongs to interface ICs, low-voltage differential signaling receivers, and high-speed CMOS interface devices. The primary features of this quad receiver include four differential receiver channels, support for data rates in excess of 400 Mbps, a typical input sensitivity of 350 mV, and CMOS output signaling. The device is designed for high-speed point-to-point links where differential signaling reduces susceptibility to common-mode noise. Its quad-channel organization also allows one package to terminate four independent data pairs. The DS90LV032A architecture uses low-power CMOS circuitry to translate the small-amplitude LVDS inputs into full-swing CMOS outputs. According to the Texas Instruments datasheet, the family supports propagation delay of up to 3.3 ns and includes low channel-to-channel and differential skew characteristics. This combination is useful when timing margins are limited, particularly in parallel data buses, backplanes, and clock-distribution networks. Typical applications include LVDS backplanes, industrial control links, high-speed instrumentation, point-to-point inter-board communication, and data-acquisition systems that require multiple low-voltage differential inputs. The device can receive data from compatible LVDS transmitters over controlled-impedance printed circuit board traces. Because it is a receiver rather than a transceiver, each channel still requires an external LVDS source and correctly terminated signal pair. PCB implementation must preserve controlled impedance, minimize stubs, and route each differential pair as a tightly coupled pair. Inputs should not be left floating when the receiver is powered, and the power-supply network should be decoupled close to the device. Because CFP packages are not represented by the available package-diagram library, the manufacturer pin-description table should be used when assigning PCB tracks. This product page combines the exact DS90LV032AW-MLS ordering information with receiver specifications, package details, drop-in alternatives, application guidance, and design considerations. The comparison information is intended to clarify temperature grade, packaging, and ordering differences before a component is selected for a high-speed LVDS interface.

RFQ پەیوەندی
DS90LV032TMX - Quad LVDS Receiver | Texas Instruments
DS90LV032TMX

DS90LV032TMX - Quad LVDS Receiver | Texas Instruments

Texas Instruments DS90LV032TMX is a four-channel differential line receiver that translates low-voltage differential signaling into 3-V CMOS output signals. It supports data rates in excess of 400 Mbps, equivalent to 200 MHz, accepts differential inputs with a typical signal magnitude of 350 mV, and is packaged in a 16-pin flat-pack configuration. The device is intended for high-speed point-to-point connections requiring low power dissipation and reliable differential-signal detection. A low-voltage differential signaling receiver is a line receiver that distinguishes the voltage difference between two conductors rather than the voltage referenced to ground. LVDS belongs to the broader interface-IC and data-converter interface hierarchy. Its differential architecture reduces sensitivity to common-mode noise, supports low-voltage signaling, and is commonly used when a system must transfer clock or data signals over a compact cable or PCB trace. The DS90LV032TMX provides four receiver channels, operation beyond 400 Mbps, and translation of approximately 350 mV differential input signals to 3-V CMOS levels. Its four-channel arrangement allows one receiver package to handle four independent data paths or multiple clock and data lanes. The low-power design is useful when the receiver must operate close to high-speed processors, FPGAs, serializers, or test equipment without adding substantial system power. Internally, the receiver compares the two differential inputs for each channel and uses the polarity of that voltage difference to recover the intended logic state. Differential detection rejects noise that appears equally on both inputs, while the CMOS output interface connects the recovered data to ordinary digital logic. The exact supply-voltage limits, propagation-delay limits, input-current limits, and temperature ratings should be taken from the manufacturer data sheet before finalizing a high-speed design. Typical applications include LVDS clock distribution, camera and video interfaces, industrial control links, test-and-measurement equipment, and general-purpose high-speed digital connections. Quad-channel density is particularly attractive when a design needs several low-voltage differential inputs but has limited board space. The receiver can also support links operating below its maximum rated speed when the source amplitude, termination, trace geometry, and timing budget satisfy the interface requirements. PCB implementation should preserve the differential characteristics of each input pair. Route the two conductors of a channel as a tightly coupled pair, provide the specified input termination, avoid stubs, and keep return-path discontinuities away from the signal traces. Differential impedance, receiver input capacitance, connector geometry, and source-edge rate can affect eye opening and therefore determine whether a nominal 400-Mbps-capable receiver maintains adequate margin. This product overview combines the DS90LV032 family specifications, package information, sourcing context, and practical implementation guidance. It also distinguishes exact-family replacements from electrically similar receivers that may use different thresholds, supply rails, or pin arrangements, helping engineers narrow a replacement search before committing to a board-level substitution.

RFQ پەیوەندی
DS90LV047ATMTC - 400 Mbps LVDS Quad Driver | Texas Instruments
DS90LV047ATMTC

DS90LV047ATMTC - 400 Mbps LVDS Quad Driver | Texas Instruments

The Texas Instruments DS90LV047ATMTC is a 3.3 V, 400 Mbps quad differential line driver that converts four CMOS, LVTTL, or TTL inputs into four LVDS differential outputs in a 16-pin TSSOP (PW) package. It provides four differential drivers and no receivers, operates across a -40 °C to 85 °C temperature range, and supports the data rates required by high-speed parallel-to-serial links. An LVDS differential line driver is an interface IC that converts single-ended digital signals into low-voltage differential pairs. Low Voltage Differential Signaling belongs to the interface IC category and uses the voltage difference between two conductors to carry data while rejecting common-mode noise. By placing four LVDS outputs in one package, the DS90LV047A family reduces component count and simplifies control of parallel data buses, clock distribution, and multi-channel point-to-point interconnects. The principal characteristics are a 400 Mbps signaling rate, four independent differential outputs, a 3.3 V supply, and CMOS-compatible inputs. Each driver supports low-power operation and fast data-rate transmission for point-to-point links. The 16-pin TSSOP package provides a compact surface-mount footprint suitable for communications equipment, industrial controls, test equipment, and multi-channel digital backplanes. The device uses differential signaling to maintain signal integrity over cables or controlled-impedance PCB traces. Because the receiver detects the voltage difference across the pair rather than an absolute voltage at one conductor, common-mode disturbances caused by nearby switching circuitry are substantially rejected. Four channels can transmit related control, data, or clock signals while keeping channel-to-channel skew and power distribution under centralized design control. Typical uses include parallel-to-serial data transmission, clock distribution, backplane links, video and imaging interfaces, industrial automation equipment, and test-and-measurement systems. The quad architecture is particularly useful when four independent high-speed channels must share the same supply, ground, and board area. The device is designed to work with the companion DS90LV048A family of quad LVDS receivers when a system requires balanced transmission and reception. PCB implementation should use controlled-impedance differential routing, symmetric pair geometry, and a continuous ground reference beneath the signal traces. Keep the LVDS outputs away from high-current switching paths, and terminate the receiving end according to the receiver manufacturer's recommendations. Verify the final eye pattern, skew, and common-mode behavior at the system level because connector and cable effects can materially limit a 400 Mbps link. This page consolidates manufacturer product information, ordering details, cross-reference candidates, and practical interface-design guidance. It also identifies the distinctions between the available ordering codes so engineers can select a functionally equivalent part without overlooking packing, marking, or temperature-range differences.

RFQ پەیوەندی
DS90LV047ATMTC/NOPB - 400 Mbps LVDS Quad Driver | TI 16-TSSOP
DS90LV047ATMTC/NOPB

DS90LV047ATMTC/NOPB - 400 Mbps LVDS Quad Driver | TI 16-TSSOP

The Texas Instruments DS90LV047ATMTC/NOPB is a 400 Mbps (200 MHz) quad CMOS flow-through differential line driver implementing Low Voltage Differential Signaling (LVDS) technology, housed in a 16-pin TSSOP package. The device accepts LVTTL/CMOS input levels and translates them to a 350 mV differential LVDS output, providing ultra-low power dissipation and high data rates for point-to-point high-speed interface applications. A line driver in the LVDS family is a transceiver front-end component that converts single-ended logic levels into a low-voltage differential pair, and the DS90LV047A belongs to that LVDS sub-family which also includes line receivers (DS90LV048A), transceivers (DS90LV049), and serializers/deserializers. Within the broader hierarchy of interface ICs, LVDS drivers sit under differential signaling ICs, which themselves sit under interface ICs, then under wired-connectivity ICs, and finally under integrated circuits. The DS90LV047A and companion line receiver DS90LV048A provide an alternative to high-power pseudo-ECL devices, offering CMOS-level power consumption with multi-hundred-megahertz switching speeds. Key features include four independent drivers with flow-through pinout, typical differential output swing of 350 mV across a 100 ohm load, support for data rates in excess of 400 Mbps (200 MHz toggle rate), and 3.3 V nominal supply operation from 3.0 V to 3.6 V. Flow-through pin ordering simplifies PCB routing by allowing the input on one side and the LVDS output on the opposite side, which reduces layer count and via usage. The architecture uses a current-mode LVDS driver stage with on-chip termination, providing controlled edge rates, low EMI, and robust common-mode noise immunity. The wide common-mode range on the differential pair and the LVDS standard's inherent noise margin allow reliable transmission over FR-4 backplanes and ribbon cable at lengths exceeding several meters. Typical applications include LCD display row/column drivers, board-to-board high-speed data links, clock distribution networks, printers and copiers, network switches and routers, and backplane interconnect for telecommunications equipment. The device is also commonly paired with the DS90LV048A quad receiver to form complete LVDS links. When designing with this device, maintain a 100 ohm differential termination at the receiver end of the pair, place decoupling capacitors close to the VCC pin, and keep differential traces matched within 10 mil to preserve duty-cycle balance and minimize reflections. This page synthesizes distributor pricing, drop-in TSSOP alternatives, and practical design guidance not found in the manufacturer datasheet.

RFQ پەیوەندی
DS90LV047ATMTCX - 400Mbps Quad LVDS Driver | Texas Instruments
DS90LV047ATMTCX

DS90LV047ATMTCX - 400Mbps Quad LVDS Driver | Texas Instruments

The Texas Instruments DS90LV047ATMTCX is a 400 Mbps quad CMOS flow-through differential line driver with four LVDS transmitters, a 3 V to 3.6 V supply range, and a 16-pin TSSOP (PW) package. It converts low-voltage TTL/CMOS inputs into low-voltage differential LVDS outputs for high-speed point-to-point interfaces. The device supports data rates in excess of 400 Mbps, equivalent to more than 200 MHz according to the manufacturer product page. An LVDS differential line driver is an interface IC that transmits complementary signals through a balanced pair. Because the two conductors carry equal and opposite signals, the transmitted signal is less susceptible to common-mode noise than a single-ended interface. This makes the DS90LV047A family suitable for links requiring low power consumption, high data rates, and reliable point-to-point signal transfer across a board or cable. The principal verified features are four differential outputs, a 3 V to 3.6 V supply, a 400 Mbps signaling rate, and low-voltage differential signaling. The flow-through architecture supports signal routing where data enters and exits on corresponding package sides. The manufacturer identifies the device as an alternative to high-power pseudo-ECL devices in high-speed point-to-point interface applications. The DS90LV047ATMTCX is a line driver rather than a receiver, ADC, DAC, or transceiver. Each of its four channels accepts TTL or CMOS logic and produces an LVDS differential output. The 16-pin TSSOP package is suitable for compact surface-mount layouts, while the quad-channel arrangement reduces the number of interface ICs needed when several independent links are required. Typical applications include high-speed backplanes, point-to-point industrial links, digital video and control paths, communications equipment, and instrumentation requiring reliable differential transmission. The companion DS90LV048A family provides line receivers, allowing a transmitter and receiver pair to be designed into a complete LVDS link. For PCB design, place the driver close to the source device, route differential pairs with matched geometry, and keep the pair away from unrelated high-current switching nodes. Confirm LVDS output amplitude, receiver compatibility, termination, and edge-rate requirements using the manufacturer datasheet before releasing a new layout. This page combines verified manufacturer and distributor information with practical interface design guidance, application context, and replacement considerations that are not present in a raw distributor listing.

RFQ پەیوەندی
DS90LV048ATM - 400 Mbps Quad LVDS Receiver | Texas Instruments
DS90LV048ATM

DS90LV048ATM - 400 Mbps Quad LVDS Receiver | Texas Instruments

The Texas Instruments DS90LV048ATM is a 3.3 V quad CMOS differential line receiver supporting LVDS signaling rates above 400 Mbps, equivalent to 200 MHz, in a 16-pin SOIC package. It accepts differential inputs with a typical signal amplitude of 350 mV and provides four independent receiver channels for high-speed point-to-point data links. The device is designed for low-power operation and an industrial temperature range of -40°C to +85°C. An LVDS receiver is an interface integrated circuit that converts a low-voltage differential signal into a complementary CMOS logic output. LVDS, or Low Voltage Differential Signaling, belongs to the differential interface IC hierarchy and supports reliable high-speed communication by comparing the voltage difference between two conductors. By rejecting common-mode noise and using low swing levels, LVDS is well suited to compact industrial, communications, and data-processing systems. The DS90LV048A family provides four flow-through differential receivers and supports data rates in excess of 400 Mbps. Its 350 mV typical differential input amplitude allows it to operate with the companion DS90LV047A line-driver family. The receiver architecture translates each differential LVDS input into a CMOS output suitable for downstream digital logic, while its quad-channel organization consolidates four links into one 16-pin device. The flow-through arrangement helps preserve signal timing by keeping the data path direct through the package. This is particularly valuable in point-to-point links where receiver-to-logic propagation delay must remain predictable. A listed 1.5 ns propagation-delay value and 15 mA operating-current figure place the device in the low-power, high-speed interface class, although application-specific limits should be checked against the manufacturer datasheet before final timing and power-budget calculations. Typical uses include point-to-point links between a transmitter and field-programmable gate array, industrial control equipment, video-processing systems, and other high-speed digital backplanes. The quad receiver can reduce component count when four differential channels are required. It is also appropriate where a 3.3 V supply and CMOS outputs match the receiving logic, while cable length, connector behavior, connector pin assignments, and system-level LVDS timing remain design constraints. For PCB implementation, place the receiver close to the source connector, route the differential pair as a tightly coupled pair, and provide a solid ground reference. Keep unused receiver inputs properly terminated according to the device recommendations. Confirm supply sequencing, output-load limits, and the relationship between input threshold, propagation delay, and system timing before operating the link at its maximum data rate. This product overview combines the manufacturer's functional description with package, interface, sourcing, replacement, and layout guidance. It also distinguishes genuine same-footprint receiver options from functionally similar parts that require separate electrical and timing review, helping engineers select a replacement without overlooking enable, pinout, or temperature requirements.

RFQ پەیوەندی
DS90LV048ATMTC - 400 Mbps Quad LVDS Receiver | Texas Instruments
DS90LV048ATMTC

DS90LV048ATMTC - 400 Mbps Quad LVDS Receiver | Texas Instruments

The Texas Instruments DS90LV048ATMTC is a 3 V quad CMOS differential line receiver supporting data rates above 400 Mbps, equivalent to 200 MHz, in a 16-pin TSSOP package. It accepts four Low Voltage Differential Signaling inputs and provides CMOS-compatible outputs for high-speed point-to-point interfaces. The receiver architecture emphasizes ultra-low power dissipation and accommodates balanced LVDS signaling. An LVDS receiver is a differential interface circuit that extracts a digital signal from two complementary low-voltage conductors. LVDS belongs to the high-speed differential-signaling family and sits below general-purpose interface ICs in the semiconductor hierarchy: receiver IC -> differential line receiver -> interface IC -> semiconductor. Its differential architecture improves noise immunity by detecting the voltage difference between a pair of lines rather than relying on a single conductor referenced only to ground. The DS90LV048A family provides four independent receiver channels, a 400 Mbps signaling rate, operation from a 3.3 V supply, and common enable control for the output stage. The flow-through signal path supports straightforward point-to-point links between a compatible LVDS transmitter and receiving logic. CMOS outputs allow the device to interface with digital systems operating from the same 3.3 V rail. Electrical operation depends on the differential input voltage and receiver threshold rather than single-ended logic levels. The LVDS input arrangement improves signal-to-noise ratio and reduces sensitivity to common-mode noise when the transmitter, receiver, connectors, and cable form a controlled impedance environment. The manufacturer identifies the DS90LV048A as a low-power alternative to high-power PECL and ECL devices in suitable point-to-point applications. Typical uses include industrial control links, instrumentation, video or imaging backplanes, test equipment, and communications equipment requiring several high-speed LVDS channels. The quad-channel configuration reduces package count compared with discrete single-channel receivers. In point-to-point links, the DS90LV048ATMTC can be paired with an LVDS line driver such as the DS90LV047A while preserving the low-voltage differential signaling architecture. PCB implementation should use a compact, controlled-impedance routing scheme and place termination close to the receiver when the selected link topology requires it. Differential pair spacing and length matching should follow the characteristics of the LVDS transmitter and interconnect. Supply and ground distribution should be decoupled close to the device because simultaneous switching across four fast receiver channels can create transient current in the power rails. This page combines the manufacturer's receiver specifications, ordering details, practical interface guidance, and qualified same-footprint references. It also distinguishes confirmed orderable variants from broader functional alternatives, helping engineers assess replacement compatibility before changing an LVDS link or PCB assembly.

RFQ پەیوەندی