بەرهەمەکان (5,100+)

DS90CR288MTD - 28-Bit 75MHz LVDS Receiver | Texas Instruments
DS90CR288MTD

DS90CR288MTD - 28-Bit 75MHz LVDS Receiver | Texas Instruments

Texas Instruments DS90CR288MTD is a 28-bit, four-data-channel LVDS receiver operating from a 3 V to 3.6 V supply at up to 75 MHz in a 56-pin TSSOP package. It is designed for Channel Link data transmission over balanced interconnects, recovering four LVDS data streams and associated clock information from a transmitting device such as the DS90CR285 family. A channel-link receiver is an interface IC that converts low-voltage differential signaling into parallel CMOS or TTL-compatible data. LVDS belongs to the broader differential-signal interface hierarchy, where low voltage swing, common-mode control, and balanced routing reduce susceptibility to noise. The DS90CR288MTD is consequently positioned between external data-transmission hardware and the digital logic, FPGA, display, or image-processing subsystem that consumes the recovered parallel data. The device supports 28 bits across four receiver channels and uses rising-edge data-strobe signaling. Its stated operating frequency is 75 MHz, while its 3 V to 3.6 V supply range suits 3.3 V digital systems. The receiver architecture is intended for point-to-point cable or PCB links carrying serialized parallel data, including video, imaging, control, and industrial communication systems. The transmitter converts parallel source data into differential LVDS streams, while the receiver performs the complementary conversion at the far end of the link. The 56-TSSOP package provides a practical surface-mount interface for systems requiring 28 parallel data bits and several control and power pins. Because the part exposes many high-speed and low-voltage signals, layout quality directly affects signal integrity. Differential impedance-controlled routing, matched pair length adjustment, a solid ground plane, and careful separation from noisy power converters are important. Input and bypass connections should also be arranged to minimize loop area and maintain a clean return path. DS90CR288MTD is appropriate when the system already uses a compatible Channel Link transmitter and requires a dedicated 28-bit LVDS receiver. The interface is preferable to converting parallel data through a general-purpose transceiver when the PCB already contains the required 56-TSSOP footprint. The main engineering trade-off is that this is a specialized receiver: its function, pinout, supply requirements, and data-strobe convention must match the transmitter and the receiving logic. For reliable implementation, use the manufacturer datasheet pin description, recommended decoupling, and reference-layout guidance without modification. Confirm the exact clock topology, input mapping, termination arrangement, exposed-pad requirements, and signal amplitudes during schematic review. This page combines the confirmed operating characteristics, packaging information, sourcing structure, and engineering guidance needed to evaluate DS90CR288MTD before committing the PCB layout. Once the transmitter, receiver, and downstream logic are verified as a complete link, DS90CR288MTD provides a direct 28-bit LVDS receiving path in 3.3 V systems. Its fixed protocol and package make design reuse straightforward, but pin-level compatibility and link-level timing must be checked rather than assumed from the Channel Link label alone.

RFQ پەیوەندی
DS90CR288MTDX - 28-Bit 75MHz LVDS Receiver | Texas Instruments
DS90CR288MTDX

DS90CR288MTDX - 28-Bit 75MHz LVDS Receiver | Texas Instruments

Texas Instruments DS90CR288MTDX is a 28-bit Channel Link LVDS receiver operating from a 3.3 V supply at up to 75 MHz, with a rising-edge data-strobe interface and a 56-TSSOP package. It is designed for high-speed point-to-point links that require a wide data path, differential signaling, and a separate strobe signal for source-synchronous data capture. An LVDS receiver is an interface IC that converts low-voltage differential signaling into a digital logic signal suitable for processing by another device. LVDS belongs to the differential interface hierarchy and provides a way to transfer high-speed data while reducing sensitivity to noise and voltage offsets. The DS90CR288 combines a 28-bit parallel data interface with a 75 MHz Channel Link receiver, placing it in the broader category of interface ICs used for communication links. Key features include 28 received data bits, a 75 MHz operating frequency, 3.3 V operation, rising-edge data strobing, and a 56-TSSOP package. The wide parallel data path reduces the number of serial links needed when transferring multi-bit information. The separate clock or data strobe provides a timing reference that can be phase-adjusted in the system, while differential reception helps preserve signal integrity across longer printed-circuit-board connections. The DS90CR288 belongs to the Channel Link family of balanced digital-interface devices. Its receiver architecture is intended for point-to-point interconnections rather than multidrop buses, and its interface is designed around source-synchronous timing. System performance depends on maintaining controlled differential impedance, providing adequate input termination, and routing the data and strobe signals so that timing margin is preserved at the receiving device. Typical uses include industrial control and instrumentation, digital video transport, test and measurement equipment, communications modules, and embedded systems that transfer a 28-bit word at 75 MHz. In each case, the receiver can provide a parallel data path to an FPGA, ASIC, microcontroller, or data converter without requiring a separate narrow serial receiver for every bit. Layout should keep the differential clock and data pairs routed as controlled-impedance nets, with pair geometry maintained consistently from transmitter to receiver. Place termination components close to the receiver inputs and avoid stubs or unnecessary layer changes. The system designer should also verify receiver input thresholds, setup and hold timing, and the relationship between the data-strobe phase and the destination device capture clock. This product page combines the manufacturer-defined receiver identity, package information, comparison details, and practical interface-design guidance. It is intended to help engineers locate the correct pin-compatible family options and plan the PCB, timing, signal-integrity, and sourcing steps needed to deploy the DS90CR288MTDX successfully.

RFQ پەیوەندی
DS90CR482VS - 5.38Gbps 48-Bit LVDS Deserializer | TI
DS90CR482VS

DS90CR482VS - 5.38Gbps 48-Bit LVDS Deserializer | TI

Texas Instruments DS90CR482VS is a 48-bit LVDS Channel Link deserializer operating at 65–112 MHz, with eight differential inputs and 48 parallel CMOS/TTL outputs. The device handles an aggregate data rate of 5.38 Gbps and is packaged in a 100-pin TQFP measuring 14 mm by 14 mm. It is the receiving counterpart to the DS90CR481 serializer and supports high-speed point-to-point data transfer over balanced LVDS links. A deserializer is an interface IC that reconstructs a group of parallel digital signals from serialized differential transmissions. In the LVDS Channel Link hierarchy, the DS90CR482VS belongs to the serializer and deserializer class, within interface ICs and semiconductor signal-conditioning products. Balanced differential signaling improves noise immunity by detecting voltage differences rather than relying on a single conductor referenced to ground. The headline specifications verified for this device are a 48-bit parallel output bus, eight LVDS input channels, a 5.38 Gbps aggregate data rate, and a 65–112 MHz operating frequency range. Its 100-pin TQFP package provides dedicated connections for data, clocking, control, power, and ground. These characteristics make the device relevant to industrial data acquisition, video transport, embedded control backplanes, and other systems that move wide parallel data across a compact cable. The DS90CR482 receives eight differential data inputs and returns 48 parallel outputs. The DS90CR481 description in the supplied material states that the companion transmitter samples 48 CMOS/TTL input bits every transmit-clock cycle and serializes them into eight LVDS streams, with a ninth LVDS link carrying the phase-locked transmit clock. The receiving device reverses this arrangement and reconstructs the parallel data bus. Typical system-level uses include high-speed control links, industrial automation equipment, test systems, video interfaces, and communication equipment. In each case, the principal benefits are reduced connector pin count, lower signal-pickup susceptibility than single-ended transmission, and the ability to move a 48-bit parallel bus across a differential link. Cable length, skew, termination, clocking, and ground-return design remain system-level constraints. Designers should treat the 5.38 Gbps figure as an aggregate signaling rate rather than 5.38 Gbps on every input. Controlled-impedance routing, correct LVDS termination, compliant connector geometry, and verification of inter-pair skew are essential. Exact supply-voltage tolerances, output timing, output capacitance, and recommended passive-component values must be confirmed in the official Texas Instruments datasheet before schematic release. This page consolidates verified distributor inventory and pricing, official product-page information, a verified TI ordering designation, and practical selection guidance. It also clearly identifies electrical and mechanical details that were not present in the supplied source data, preventing unsupported assumptions about voltage ratings, timing, compliance, or pin assignments.

RFQ پەیوەندی
DS90CR483VJD - 48-Bit LVDS Serializer | Texas Instruments
DS90CR483VJD

DS90CR483VJD - 48-Bit LVDS Serializer | Texas Instruments

Texas Instruments DS90CR483VJD is a 48-bit Channel Link serializer that converts parallel CMOS/TTL input data into eight LVDS output streams. It operates with a parallel clock frequency from 33 MHz to 112 MHz, supports an aggregate data rate of 5.38 Gbps, and is packaged in a 100-pin TQFP measuring 14 mm by 14 mm. A Channel Link serializer is a high-speed parallel-to-serial interface IC used to move multiple bits of digital data across a balanced cable or PCB link. Its function sits within the broader LVDS interface and data-converter hierarchy: parallel CMOS data enters the serializer, is transmitted on eight differential outputs, and is reconstructed by a compatible deserializer such as the DS90CR484. Differential signaling improves noise immunity and supports reliable communication over longer cable runs than a single-ended parallel interface. The DS90CR483VJD accepts 48 parallel data inputs and provides eight differential LVDS outputs. Its maximum clock frequency of 112 MHz supports increased bandwidth compared with earlier Channel Link generations. The manufacturer datasheet also identifies selectable pre-emphasis as an enhancement for improved cable drive. A 3 V supply and an LVDS output amplitude of approximately 0.45 V are identified in the product documentation. Internally, the device acts as the transmit-side half of a Channel Link chipset. Parallel CMOS/TTL data is serialized onto eight LVDS channels, reducing the number of signal conductors required compared with a wide parallel bus. The architecture is intended to pair with the DS90CR484 deserializer, which reconstructs the transmitted word and recovers the parallel clock. This division of transmit and receive functions allows each endpoint to connect a parallel source or destination to a differential serial link. Typical applications include high-speed industrial data acquisition, instrumentation backplanes, professional video and imaging equipment, communications infrastructure, test and measurement systems, and embedded control platforms that must transfer wide parallel words across a compact differential interface. The eight LVDS outputs can also support redundant or segmented communication paths when the complete system architecture permits it. Designers should treat the serializer as a high-speed differential interface rather than a general-purpose logic device. Controlled-impedance routing, uninterrupted reference planes, compliant LVDS termination, and careful clock distribution are essential. The DS90CR483VJD is normally used as the transmitting endpoint, so the deserializer part number, cable length, connector, pre-emphasis setting, and system clocking must be selected together before PCB layout begins. This product page consolidates the verified electrical identity, interface architecture, package information, replacement considerations, and practical design guidance for the DS90CR483VJD. It also separates the serializer from its complementary DS90CR484 deserializer so engineers can assess the complete chipset rather than treating a single half of the link in isolation.

RFQ پەیوەندی
DS90CR561MTD - LVDS Flat Panel Interface | Texas Instruments
DS90CR561MTD

DS90CR561MTD - LVDS Flat Panel Interface | Texas Instruments

The Texas Instruments DS90CR561MTD is an interface IC identified for LVDS flat-panel display applications, supplied in a 48-pin TSSOP package. The confirmed product listing classifies it as an interface IC and specifies a 0.45 V interface-related operating value, while the part designation identifies it as a member of the DS90CR561 interface family. Its 48-pin TSSOP construction provides a defined board-level footprint for systems requiring a dedicated digital display interface function. An LVDS flat-panel interface IC is a semiconductor device used to connect digital video or control logic to display-related circuitry through low-voltage differential signaling. Within the broader hierarchy, an LVDS interface IC belongs to interface ICs, data converters and communication devices, and ultimately to integrated circuits. Differential signaling can reduce susceptibility to common-mode interference compared with single-ended interconnects, provided the transmitter, receiver, connector, and printed-circuit-board geometry are designed together. The DS90CR561MTD provides a defined integration point for flat-panel display equipment. Its 48-pin TSSOP package supports conventional surface-mount assembly and external decoupling, power, ground, and differential-signal routing. Because this page does not reproduce the complete manufacturer datasheet, detailed electrical limits should be confirmed in the manufacturer documentation before finalizing a PCB, selecting termination networks, or calculating signal-integrity margins. Potential uses include digital flat-panel display controllers, industrial HMI panels, test and measurement equipment, medical display interfaces, and embedded human-machine-interface systems. The part is most relevant when the system architecture already uses an LVDS display link and the designer can confirm compatibility with the DS90CR561 interface requirements. When designing a PCB around the DS90CR561MTD, preserve the manufacturer's recommended pin assignments, component placement, and differential-pair geometry. Validate power sequencing, input thresholds, output timing, and termination values against the official datasheet. Do not infer missing electrical ratings from the distributor category label or the abbreviated package description. This page combines the confirmed 48-TSSOP LVDS flat-panel interface identification with engineering-oriented selection guidance, application analysis, package-aware alternatives, and design cautions. It is intended to accelerate engineering triage while keeping unconfirmed electrical details separate from verified product facts.

RFQ پەیوەندی
DS90CR561MTDX - 18-Bit LVDS FPD Transmitter | Texas Instruments
DS90CR561MTDX

DS90CR561MTDX - 18-Bit LVDS FPD Transmitter | Texas Instruments

Texas Instruments DS90CR561MTDX is an 18-bit color flat-panel-display link transmitter that converts 21 bits of CMOS/TTL data into three LVDS data streams. It is packaged in a 48-pin TSSOP and belongs to the DS90CR561/DS90CR562 flat-panel-display interface family. Its three-channel architecture is designed for parallel display data to be serialized onto low-voltage differential signaling links. An LVDS flat-panel-display interface is a high-speed differential link used to connect digital video source logic to panel timing controllers and display drivers. In this hierarchy, an LVDS transmitter serializes parallel CMOS/TTL data into differential outputs, while the receiving electronics recover the data at the display end. Differential signaling helps limit common-mode noise pickup, making the approach suitable for compact systems containing parallel pixel data and clock information. The DS90CR561MTDX accepts 21 bits of CMOS/TTL input and organizes that information into three LVDS streams. This format corresponds to an 18-bit color display link, with additional data carrying display-related information. The transmitter therefore acts as the source-side interface between a parallel display engine and an LVDS-based panel connection, reducing the number of conductors required relative to a parallel-only implementation. The DS90CR561 and DS90CR562 family is identified in the manufacturer documentation as an 18-bit color flat-panel-display link. The DS90CR561MTDX is supplied in the 48-pin TSSOP package, identified in distributor records as PDSO48 with gull-wing terminals and surface mounting. Package-level details, pin assignments and electrical limits should be confirmed against the DS90CR561 manufacturer datasheet before a new PCB is released. Typical uses include flat-panel monitors, industrial panel displays, and embedded display systems that generate parallel RGB pixel data and require an LVDS interface to a remote controller. The 21-bit parallel input and three serialized LVDS outputs make the device particularly relevant to display architectures where cable count, signal integrity and panel interoperability must be considered together. PCB design should preserve the differential signal geometry specified by the DS90CR561 family documentation. LVDS pairs should be routed as controlled-impedance, tightly coupled traces, with the transmitter and connector positioned to minimize interruption of the differential path. The data sheet pin-description table is the authoritative source for assigning the 48 TSSOP terminals and grounding functions. This product page combines the DS90CR561MTDX identity, package information, LVDS interface description, sourcing guidance and verified drop-in candidates with practical selection and layout considerations. It also distinguishes mechanically similar ordering codes from confirmed functional equivalents, helping engineers evaluate replacements without assuming that an identical package alone guarantees electrical and timing compatibility.

RFQ پەیوەندی
DS90CR562MTD - 18-Bit LVDS FPD-Link Receiver | Texas Instruments
DS90CR562MTD

DS90CR562MTD - 18-Bit LVDS FPD-Link Receiver | Texas Instruments

The Texas Instruments DS90CR562MTD is a 21-bit LVDS receiver for 18-bit color flat-panel display links, operating from a 4.5 V to 5.5 V supply and packaged in a 48-pin TSSOP. It is designed to receive three LVDS data streams carrying 18-bit RGB pixel data and a transmitted phase-locked clock. The receiver supports CMOS/TTL-compatible downstream display interfaces and is positioned for compact flat-panel display systems, industrial monitors, and legacy LVDS display-control equipment. An LVDS receiver is an interface circuit that restores low-voltage differential signaling data at the display end of a link. FPD-Link is a display-oriented interface standard that transports parallel video data over differential pairs. In the DS90CR562MTD, the LVDS input stage recovers three data streams and separates the transmitted clock information, allowing a display controller or timing circuit to reconstruct pixel data. The principal electrical characteristics include a 4.5 V to 5.5 V supply range, 21 receiver inputs, three data streams, and LVDS protocol support. The package is a 48-TSSOP, also identified in the product listing as 48-TFSOP with a 0.240 inch, 6.10 mm width. The listed packaging format is Tube, and the device is categorized as an interface IC for specialized display-link applications. The DS90CR562MTD is primarily intended for systems using the National Semiconductor DS90CR561 transmitter and DS90CR562 receiver family. Its architecture supports the transfer of 18-bit color information over an LVDS display link rather than conventional parallel RGB wiring. This can reduce signal-routing complexity and support a more compact connection between a display engine and a flat-panel display timing controller. Designers should verify differential pair routing, LVDS input impedance, termination strategy, supply decoupling, and the exact display timing requirements of the target panel before releasing a PCB layout. The receiver is a digital interface device, so a conventional power-semiconductor safe-operating-area chart does not apply. Compliance status should be confirmed against the manufacturer’s current product documentation for the exact ordering code. This page combines the documented DS90CR562MTD interface and package information with application guidance, comparison parameters, and drop-in replacement analysis for engineers evaluating display-link receiver designs.

RFQ پەیوەندی
DS90CR562MTDX - 18-Bit LVDS FPD Receiver | Texas Instruments
DS90CR562MTDX

DS90CR562MTDX - 18-Bit LVDS FPD Receiver | Texas Instruments

The Texas Instruments DS90CR562MTDX is an 18-bit FPD interface line receiver designed for flat-panel display systems. It receives differential data in a 48-TSSOP surface-mount package and belongs to the broader hierarchy of display interface ICs, interface ICs, and integrated circuits. The device is intended for use with compatible TI display link transmitters, including the DS90CF364A family, when a system must transfer multi-bit panel data reliably over a wired differential interface. The DS90CR562MTDX is identified as an IC line receiver in a 48-pin TSSOP package with gull-wing leads and a rectangular body. Its commercial temperature grade supports design use in ordinary commercial equipment rather than automotive or extended-temperature systems. The X suffix denotes the ordered package configuration, while the related DS90CR562MTD and DS90CR562MTD/NOPB listings identify the same receiver family in the same 48-TSSOP format. The central benefit of this receiver is integration: an 18-bit wide LVDS-style panel interface consolidates multiple data bits into one display-link receiver rather than requiring a separate single-channel line receiver for every signal. In an FPD system, it complements a parallel-to-differential transmitter that converts low-speed logic signals into a compact differential link. This reduces interconnect width while supporting a more structured approach to display timing and data transfer. Because the part is a receiver rather than a display timing controller or transmitter, system design must also account for the source transmitter, connector, cable, termination network, and receiving display electronics. LVDS-style links depend on correct differential routing, controlled impedance, suitable input termination, and compliant timing margins. Trace length and pair geometry are therefore as important as nominal pin compatibility when the receiver is installed. DS90CR562MTDX is appropriate for commercial flat-panel-display equipment, monitor interfaces, industrial display controllers, and other systems using the TI DS90CR562 display-link ecosystem. It should not be selected for an unrelated LVDS standard merely because the connector or protocol looks similar; signal mapping, input thresholds, supply requirements, and timing must match the associated transmitter. This page combines the exact package and product classification, sourcing links, interface guidance, and drop-in comparison with practical board-level cautions. For a new layout, consult the pin-description table and timing information in the manufacturer datasheet, preserve the receiver’s supply and ground distribution, and validate the complete transmitter-to-receiver link before production release.

RFQ پەیوەندی
DS90CR563MTD - 65MHz LVDS 18-Bit FPD-Link Transceiver
DS90CR563MTD

DS90CR563MTD - 65MHz LVDS 18-Bit FPD-Link Transceiver

The National Semiconductor DS90CR563MTD is a 65 MHz LVDS 18-bit color Flat Panel Display FPD-Link transceiver designed for high-speed digital display interfaces. The device is supplied in a 48-pin TSSOP package and combines 21 transmitter outputs with 3 receiver inputs, as identified by the verified distributor classification “21/3 Transceiver FPD-Link, LVDS 48-TSSOP.” Its 18-bit parallel data path is intended for transferring display data between a graphics source and a flat-panel display controller. An FPD-Link transceiver is an interface IC that converts parallel pixel data to a low-voltage differential signaling data stream and receives differential data back from a display panel. It belongs to the FPD-Link interface family, within the broader category of interface ICs and digital semiconductors. LVDS reduces signal amplitude while preserving high data throughput, making it suitable for point-to-point connections between a display timing controller and a panel receiver over cables or board-level interconnects. The verified source data identifies the principal operating features as LVDS signaling, 18-bit color data support, a 65 MHz link clock, 21 driver outputs, 3 receiver inputs, and a 48-pin TSSOP package. These parameters distinguish the device as a multi-channel display-interface solution rather than a general-purpose logic IC. Its transmitter and receiver count also indicates that it is intended for full digital video links carrying pixel data and control information. Technically, the DS90CR563MTD integrates parallel-to-differential and differential-to-parallel conversion into one package. The 65 MHz operating point supports the stated 18-bit color FPD-Link function, while the 21:3 transmit-to-receive arrangement supports simultaneous transfer in both directions. Exact voltage ratings, current consumption, propagation delay, differential impedance, temperature range, and connector or panel-termination recommendations were not present in the verified excerpts and therefore require confirmation from the manufacturer datasheet. Typical uses include LVDS flat-panel monitor links, digital signage interfaces, industrial display controllers, automotive passenger-information displays, and embedded human-machine-interface panels. For these systems, the key selection criteria are the 48-TSSOP footprint, 18-bit color width, 65 MHz clocking, and compatibility with the panel’s LVDS input architecture. System designers must also verify connector assignment and panel timing requirements. The primary layout consideration is the dense 48-pin TSSOP footprint. Place the device according to the datasheet pin configuration and provide the differential routing, ground reference, decoupling, and display-link topology recommended for the application. Do not assume compatibility with a different panel simply because both products use LVDS; data mapping, clocking, voltage levels, and connector assignments must be checked. This product record combines verified device classification, package information, link width, clock rate, distributor listings, and practical replacement guidance. It also identifies where missing electrical and mechanical details must be obtained, preventing unsupported assumptions during schematic review, PCB layout, and production procurement.

RFQ پەیوەندی
DS90CR581MTD 24-Bit LVDS FPD Transmitter | TI
DS90CR581MTD

DS90CR581MTD 24-Bit LVDS FPD Transmitter | TI

The Texas Instruments DS90CR581MTD is a 24-bit color flat-panel-display LVDS transmitter that converts 28 bits of CMOS/TTL pixel data into four LVDS data streams and transmits a phase-locked clock in parallel. It is packaged in a low-profile 56-lead TSSOP and operates as a commercial-temperature interface IC for flat-panel display links. The device supports data rates up to 140 megabytes per second and uses narrow differential signaling to reduce cable size, connector count, and system cost. Its LVDS output swing is 290 mV, which is compatible with TIA/EIA-644 signaling practice and is intended for low-EMI display interconnects. An LVDS transmitter is a high-speed interface device that transmits balanced differential signals over a reduced-voltage physical layer. In the display hierarchy, the DS90CR581MTD is a display interface controller, an interface IC, and ultimately a semiconductor-level signal-conditioning device. Parallel CMOS pixel data enters the transmitter, an internal phase-locked loop derives the transmitted clock, and four differential LVDS lanes carry pixel information plus synchronized data-strobe information. Key features include support for 24-bit color data, four LVDS outputs, transmission of a phase-locked clock in parallel, rising-edge data strobes, and a power-down mode. The narrow-bus architecture replaces many single-ended interconnects with fewer differential pairs, reducing board routing and cable demands. The internal PLL requires no external components according to the product documentation, simplifying system implementation. A 290 mV LVDS swing also supports low-EMI operation compared with larger single-ended transitions. The DS90CR581MTD is positioned for legacy flat-panel LCD systems, including monitor and digital display controllers that provide TTL or CMOS pixel data and require conversion to an LVDS panel link. The transmitter handles 28 bits of source data, allowing the system to carry 24 color bits together with synchronization and control information. Its phase-locked transmit clock helps the receiving panel interface recover a stable timing reference. Use the manufacturer datasheet pin-description table to assign PCB tracks because a complete 56-pin map is not reproduced on this page. Confirm panel-side clock polarity, lane mapping, and input data-strobe timing before releasing a layout. The 56-TSSOP package also requires careful power and ground-plane arrangement to prevent data corruption at high pixel-clock rates. This page organizes the display-interface details, application fit, package information, and verified comparison points into a practical engineering reference for LCD panel-link designers.

RFQ پەیوەندی
DS90CR583MTD - 65 MHz LVDS FPD Transmitter | Texas Instruments
DS90CR583MTD

DS90CR583MTD - 65 MHz LVDS FPD Transmitter | Texas Instruments

Texas Instruments DS90CR583MTD is a 65 MHz LVDS flat-panel-display link transmitter that converts 28 bits of CMOS/TTL data into four LVDS data streams and transmits a phase-locked clock over a fifth LVDS link. The device operates from a 4.5 V to 5.5 V supply and is packaged in a 56-pin TSSOP. Its parallel data architecture targets legacy LCD flat-panel interfaces that require multiple differential data lanes plus a separate clock. An LVDS flat-panel-display link transmitter is an interface IC within the broader display-interface and semiconductor hierarchy. It accepts parallel logic-level pixel data, serializes that data onto low-voltage differential pairs, and transfers the resulting signal to a compatible receiver across a cable or PCB interconnect. By combining data and clock over controlled differential signaling, the interface reduces the number of conductors required compared with a parallel display bus while supporting higher signal integrity than ordinary single-ended transmission. The DS90CR583 supports 28 CMOS/TTL input bits, four LVDS data outputs, and one LVDS clock output at a maximum signaling rate of 65 MHz. The 4.5 V minimum and 5.5 V maximum supply range suits conventional 5 V display-controller environments. The transmitter samples 28 input bits during every transmitted clock cycle, providing a straightforward mapping between the parallel source data and the serialized differential outputs. The internal architecture includes parallel-to-serial conversion, clock generation, and a phase-locked transmit clock. The phase-locked clock is transmitted in parallel with the four data streams so that a compatible DS90CR584 receiver can reconstruct the original 28-bit word. This clock-and-data arrangement is important because display timing must remain aligned across every pixel-transfer cycle. Typical applications include small-format TFT-LCD panels, industrial display controllers, medical diagnostic displays, test and measurement equipment, and legacy flat-panel systems that use FPD-Link or LVDS signaling. The transmitter is most appropriate where the host controller provides 28-bit parallel CMOS data and the display receiver supports the corresponding five-link LVDS architecture. Designers should use controlled-impedance differential routing, maintain a continuous reference plane, and place bypass capacitors close to the supply pins. The TSSOP footprint requires careful fan-out because 56 leads provide limited routing escape area. Signal-pair length matching and separation from noisy switching nodes are essential for reliable LVDS operation. This page consolidates the device architecture, interface requirements, lifecycle information, package characteristics, and application-specific design guidance into an engineering-focused reference for evaluating the DS90CR583MTD in legacy flat-panel-display systems.

RFQ پەیوەندی
DS90CR583MTDX - 65 MHz 28-Bit LVDS Transmitter | TI
DS90CR583MTDX

DS90CR583MTDX - 65 MHz 28-Bit LVDS Transmitter | TI

The Texas Instruments DS90CR583MTDX is a 65 MHz LVDS flat-panel-display link transmitter that converts 28 bits of CMOS/TTL input into four differential LVDS data streams and a fifth differential clock link. It is packaged in a 56-terminal gull-wing TSSOP with a commercial temperature grade. The device is designed for parallel-to-LVDS conversion in LCD and flat-panel display systems where a multi-lane serial interface reduces the number of traces required between the display controller and panel. An LVDS interface, also called Low Voltage Differential Signaling, is a high-speed electrical interface that transmits data through differential current pairs. Differential signaling improves noise immunity because the receiver evaluates the voltage difference between two conductors rather than the voltage of either conductor relative to ground. In this category, a line driver converts parallel logic into a low-voltage differential serial signal, while a corresponding line receiver reconstructs the parallel data. The DS90CR583 transmitter samples 28 CMOS/TTL data bits during every cycle of its transmitted clock. Four LVDS pairs carry the converted data, and a separate LVDS link carries the phase-locked transmit clock. This organization supports a 65 MHz LVDS 24-bit color flat-panel-display link while preserving a parallel source interface for the graphics or display controller. The implementation uses a phase-locked transmit clock so that the data lanes and clock lane remain aligned during transmission. Because the clock is transferred in parallel with the data streams, the receiving system can recover the transmitted word boundaries from the differential interface rather than relying on a separate source-synchronous clock conductor from the transmitter. Typical applications include LCD monitor panels, industrial HMIs, automotive display links, point-of-sale terminals, and other controller-to-panel assemblies that use a 28-bit parallel pixel bus and an LVDS display link. The transmitter is normally paired with a DS90CR584-family receiver at the panel end. System designers must also provide compatible input and output circuitry, controlled-impedance routing, and connector or cable structures suitable for low-voltage differential signaling. The main design consideration is that a panel cable and receiver must match the transmitter's data-lane count, clock arrangement, and signaling standard. Review the pin-description table, recommended decoupling, and LVDS routing guidance in the manufacturer datasheet before assigning PCB tracks or laying out the interface. This page consolidates the interface architecture, verified package information, application guidance, design notes, and drop-in replacement considerations to help engineers evaluate the DS90CR583MTDX before integrating it into a flat-panel-display link.

RFQ پەیوەندی
DS90LT012AHMFX - 400 Mbps LVDS Receiver | Texas Instruments
DS90LT012AHMFX

DS90LT012AHMFX - 400 Mbps LVDS Receiver | Texas Instruments

Texas Instruments DS90LT012AHMFX is a single CMOS differential line receiver designed for ultra-low-power, low-noise, high-speed LVDS interfaces. It supports data rates in excess of 400 Mbps, equivalent to 200 MHz, accepts a typical 350 mV differential input, and translates the signal into 3 V CMOS levels. The device is housed in a 5-pin SOT-23 package. An LVDS receiver is a high-speed interface device that converts a small-amplitude differential voltage into a conventional logic-level output. LVDS belongs to the differential line-driver and receiver family within interface ICs, where low voltage swing, common-mode rejection, and reduced crosstalk support reliable data transfer over longer printed-circuit-board traces than many single-ended interfaces. The DS90LT012AH also includes an input line-termination resistor for point-to-point applications. The principal features of the DS90LT012AHMFX are its operation above 400 Mbps, typical differential input sensitivity of 350 mV, and 3 V CMOS output operation. Its low-noise receiver architecture is intended to preserve signal integrity in systems operating at high data rates. The integrated termination also simplifies point-to-point links by reducing the need for a separate input termination network. The DS90LT012AHMFX is a single-receiver device rather than a quad-channel LVDS receiver. It is therefore suited to compact point-to-point links where channel count is secondary to package size, low power dissipation, and high signaling rate. The SOT-23-5 form factor supports dense PCB placement, although high-speed routing still requires controlled impedance and minimized trace-length mismatch. Typical applications include high-speed point-to-point backplanes, industrial control links, video and display interfaces, communications equipment, test and measurement systems, and embedded data links. In each case, the receiver can convert a low-voltage differential LVDS signal into a 3 V CMOS signal for subsequent digital processing. The companion DS90LV011AH is identified in the manufacturer material as an LVDS line driver. A critical implementation consideration is maintaining a continuous reference plane and tightly matched differential routing beneath the receiver. The input termination resistor is intended for point-to-point use, so designers should confirm whether the chosen link topology requires it. Input and output paths should also be kept short and separated from switching-current loops to preserve the receiver’s low-noise benefit. This page combines the manufacturer’s operating characteristics, package information, verified component listings, cross-reference findings, and practical PCB guidance. It also identifies the limitation of the available substitute search: the directly related candidates share the receiver package and electrical family, but no independent set of five distinct cross-brand drop-in receivers could be confirmed without risking an incorrect replacement recommendation.

RFQ پەیوەندی
DS90LT012AQMFE - 400 Mbps Automotive LVDS Receiver | Texas Instruments
DS90LT012AQMFE

DS90LT012AQMFE - 400 Mbps Automotive LVDS Receiver | Texas Instruments

The Texas Instruments DS90LT012AQMFE is a single-channel automotive LVDS differential line receiver with data rates exceeding 400 Mbps (200 MHz), a 3.3 V single-supply design, and an integrated 100 ohm typical line-termination resistor. It is packaged in the 5-pin SOT-23 surface-mount package for compact point-to-point links. An LVDS line receiver is an interface IC that converts a low-voltage differential signal into a single-ended CMOS output. The DS90LT012AQMFE accepts differential inputs of 350 mV typical and supports ANSI TIA/EIA-644-A signaling. Its hierarchy runs from a differential line receiver to an LVDS interface, then to a high-speed serial-interface IC and, ultimately, a communications or automotive electronic system. Key characteristics include a 3 V to 3.6 V supply range, an automotive temperature range of -40 °C to +125 °C, and AEC-Q100 Grade 1 qualification. The integrated termination resistor removes the need for a discrete point-to-point termination. Switching rates above 400 Mbps, 100 ps typical differential skew, and a 3.5 ns maximum propagation delay make the receiver suitable for high-speed clock and data distribution. The receiver translates the differential LVDS input into a 3 V CMOS output level. Differential signaling rejects common-mode noise carried by the cable, while the receiver's controlled skew and bounded propagation delay support reliable transmission over balanced interconnects. Its single-receiver architecture is suited to systems where one link receives data from a transmitter located on another circuit card or chassis. Typical applications include automotive infotainment and instrument-cluster links, industrial control cabinets, backplane interconnects, and high-speed clock distribution. The device is also appropriate for consumer and telecom equipment requiring a low-power LVDS-to-CMOS bridge with minimal board area and a compact 5-pin footprint. When laying out the receiver, treat the IN+ and IN+ pins as a tightly matched, impedance-controlled differential pair and route them away from switching nodes. Confirm that the system design requires onboard termination; removing or overriding the integrated 100 ohm resistor changes the termination strategy and can impair signal integrity. This page combines manufacturer specifications, package and interface details, lifecycle information, drop-in alternatives, and practical PCB guidance. It also highlights where the DS90LT012AQMFE fits relative to closely related receivers and clarifies the trade-offs between automotive qualification, packaging, and supply-chain variants.

RFQ پەیوەندی
DS90LT012ATMFX - 3V LVDS Receiver with 100Ω Termination
DS90LT012ATMFX

DS90LT012ATMFX - 3V LVDS Receiver with 100Ω Termination

Texas Instruments DS90LT012ATMFX is a 3-V LVDS single differential line receiver with CMOS output, 350 mV typical differential input sensitivity, and an integrated input termination resistor for point-to-point links. The device is packaged in a 5-pin SOT-23 package. It converts low-voltage differential LVDS signals into 3-V CMOS logic levels while supporting open, shorted, and 100Ω-terminated input fail-safe operation. An LVDS receiver is an interface IC that detects a small differential voltage across a balanced pair of conductors and converts that signal into a single-ended CMOS output. LVDS belongs to the differential data-interface hierarchy, where low signal amplitude, common-mode rejection, and balanced routing improve signal integrity over longer point-to-point interconnects. The DS90LT012A family combines this receiver function with an onboard termination network intended to simplify point-to-point PCB designs. Key features include 3-V CMOS output signaling, a typical input threshold of 350 mV, and integrated line termination. The receiver provides a HIGH output during open, shorted, and terminated fail-safe conditions, allowing downstream logic to identify an invalid physical link. Its five-pin SOT-23 package supports compact placement, while the integrated 100Ω termination removes the need for a separate input resistor in a conventional point-to-point LVDS connection. The DS90LT012A architecture is optimized for receiving differential data from a companion LVDS transmitter over a short point-to-point connection. The receiver translates the differential input into a CMOS output referenced to the receiver supply. Because this is a single receiver rather than a multi-channel transceiver, board designers gain a compact solution for links that require one differential data channel, such as clock distribution, low-speed control links, or isolated command interfaces using compatible LVDS signaling. Typical uses include LVDS clock-recovery links, point-to-point command and control channels, industrial equipment links, and test systems where a low-amplitude differential receiver is preferred. In a point-to-point circuit, the companion transmitter drives the differential pair and the DS90LT012ATMFX provides a direct CMOS output for the receiving controller or logic device. The integrated termination should be considered during signal-integrity analysis because it loads the transmission line and influences edge behavior. PCB implementation requires a short, balanced route between the transmitter and receiver, with the differential pair terminated at the receiving end. Place the receiver close to the connector or driver to minimize stub length and reflections, maintain closely matched routing geometry, and connect the supply and ground pins to a low-impedance plane. The manufacturer datasheet should be used for final pin assignments, bypass requirements, and input/output truth tables before layout release. This product overview combines the manufacturer interface description with practical comparison, application, and layout guidance. It highlights the DS90LT012ATMFX's integrated termination and fail-safe behavior while separating verified electrical facts from parameters that still require confirmation from the complete device documentation or an individual design validation.

RFQ پەیوەندی
DS90LV001TLD - 800 Mbps LVDS Buffer | Texas Instruments
DS90LV001TLD

DS90LV001TLD - 800 Mbps LVDS Buffer | Texas Instruments

The Texas Instruments DS90LV001TLD is a single-channel LVDS-to-LVDS buffer designed for high-speed signal transmission at up to 800 Mbps. The device operates from a 3 V to 3.6 V supply, supports an industrial temperature range of -40°C to +85°C, and is offered in an 8-WSON package with a 3 mm by 3 mm footprint. Its LVDS input and LVDS output provide a transparent differential signal path for backplanes and other distributed high-speed systems. The DS90LV001TLD belongs to the LVDS interface IC category, where LVDS means low-voltage differential signaling. LVDS is a differential signaling method used to transmit high-speed data reliably over balanced interconnects while reducing sensitivity to noise and electromagnetic interference. A buffer or re-driver is placed between a source and a receiver when the transmission-line path, connector, backplane, or receiver fan-out cannot be handled directly by the original driver. Key features include a maximum data rate of 800 Mbps, a typical propagation delay of 2.0 ns according to the component specification, and a supply current of 70 mA. The device provides an output enable function that allows the LVDS output to be placed in TRI-STATE. It is also compatible with the ANSI/TIA/EIA-644-A LVDS standard, providing a defined reference for differential signaling operation. The DS90LV001 uses a fully differential data path, allowing the output to preserve the logical signal presented at the differential input. This characteristic is useful when signal integrity, common-mode behavior, and repeatable receiver loading matter. The device is intended for single-channel buffering and distribution rather than multi-channel conversion, so a board using several independent links may require one device per link. Typical applications include LVDS backplane buffering, high-speed point-to-point links, clock distribution through LVDS-compatible paths, and signal conditioning between transmitter and receiver equipment. The 8-WSON package reduces board area compared with the 8-pin SOIC option described for the DS90LV001 family, making it useful when compact routing is required. When laying out a circuit around the DS90LV001TLD, preserve the controlled-impedance differential transmission-line path, connect the differential pair over a continuous reference plane, and keep the input and output interfaces free of unnecessary branch stubs. The output-enable function should be driven only after the system supply and interface state are valid. This page combines the DS90LV001TLD electrical characteristics, package information, verified source links, and practical interface guidance to support design selection and sourcing. It also clarifies which documented replacement parts are appropriate for a same-footprint LVDS buffer application and which specifications require engineering review.

RFQ پەیوەندی
DS90LV001TLD-NS - 800 Mbps LVDS Buffer | Texas Instruments
DS90LV001TLD-NS

DS90LV001TLD-NS - 800 Mbps LVDS Buffer | Texas Instruments

The Texas Instruments DS90LV001TLD-NS is a single-channel 800 Mbps LVDS-to-LVDS buffer with a typical propagation delay of 1.4 ns and typical peak-to-peak jitter of 100 ps, housed in an 8-WSON surface-mount package measuring 3 x 3 mm. It operates from a single 3.3 V supply and provides a fully differential signal path for backplane and point-to-point LVDS links. An LVDS buffer is a high-speed interface IC that regenerates a low-voltage differential signaling signal while preserving the logic state and differential signaling characteristics required by the receiver. In the electronics hierarchy, the DS90LV001 belongs to the LVDS interface-buffer class, interface IC category, and broader signal-integrity and data-communication semiconductor family. Its primary role is to isolate and restore signals traveling through controlled-impedance board traces, especially when long traces, connectors, or backplane stubs create loading and reflections. The device provides an 800 Mbps data rate, 1.4 ns typical propagation delay, and 100 ps typical peak-to-peak jitter when tested with a 2^23 - 1 pseudo-random binary sequence. It is compatible with the ANSI/TIA/EIA-644-A LVDS standard. The manufacturer also specifies an industrial temperature range of -40 °C to +85 °C and offers both 8-pin SOIC and space-saving 8-WSON options, with the WSON body saving approximately 70% of board area relative to the SOIC option. The fully differential input-to-output architecture helps maintain common-mode control and rejects noise that is common to both conductors. Because the DS90LV001 is designed for 800 Mbps operation, PCB layout remains a critical part of the design. Differential impedance, component placement, return paths, connector geometry, and transmission-line termination must be evaluated together to preserve signal integrity at the intended data rate. Typical applications include LVDS clock distribution, backplane signal conditioning, point-to-point links between industrial controllers, high-speed instrumentation, test and measurement equipment, and communication systems that distribute differential signals over controlled-impedance interconnect. The buffer is particularly useful when the source and destination are not close enough for a clean direct connection or when a transmission-line segment needs regeneration before another receiver stage. Use the manufacturer's pin-description table and recommended-layout guidance when assigning PCB tracks. Keep the differential pair continuous with matched geometry, place termination components close to the receiving device, and route over a continuous reference plane. Avoid adding unterminated stubs because they can create reflections that degrade the 800 Mbps edge rate. This page combines the manufacturer specifications, replacement information, package details, and application-oriented design guidance in one engineering reference. It also distinguishes the exact orderable MPN from other DS90LV001 ordering codes so procurement, footprint review, and signal-integrity validation can be completed against the correct device.

RFQ پەیوەندی
DS90LV001TM - 800 Mbps 3.3V LVDS Buffer | Texas Instruments
DS90LV001TM

DS90LV001TM - 800 Mbps 3.3V LVDS Buffer | Texas Instruments

The Texas Instruments DS90LV001TM is a 3.3 V single-channel LVDS-to-LVDS buffer designed for data rates up to 800 Mbps and supplied in an 8-pin SOIC package. It accepts an LVDS input signal and provides an LVDS output signal for rebuilding and distributing high-speed differential data across backplanes, cable assemblies, and board-to-board links. An LVDS buffer is a low-voltage differential-signaling interface device that improves signal integrity by receiving a differential data stream and retransmitting it as a new LVDS signal. In the technology hierarchy, LVDS signaling belongs to high-speed differential interface electronics, while the DS90LV001TM is specifically a signal buffer rather than a general-purpose logic gate, transceiver, or isolation device. Its buffering function can isolate a transmitter from downstream loading and can help extend usable routing options when transmission-line impedances are controlled. According to the Texas Instruments product page and manufacturer datasheet, key verified features include an 800 Mbps maximum data rate, 3.3 V supply operation, one buffered channel, CMOS technology, and an operating temperature range of -40 °C to +85 °C. The manufacturer describes the part as an LVDS-LVDS buffer, confirming that both the input and output use LVDS signaling. The distributor listings classify the DS90LV001TM as an 8-SOIC signal buffer or re-driver. At the circuit level, the device provides a defined input stage, an internal signal path, and an LVDS output stage intended for controlled-impedance routing. LVDS systems commonly require correct termination, controlled differential impedance, and careful branch or stub management. Because the verified data identifies the part as an 800 Mbps LVDS buffer but does not provide detailed rise-time, jitter, propagation-delay, input-capacitance, output-voltage, or differential-threshold figures, those characteristics should be confirmed in the manufacturer datasheet before release to production. Typical uses include LVDS clock distribution, point-to-point backplane links, cable extension, test and measurement equipment, industrial control systems, and communication equipment. In each case, the buffer is most useful when the source cannot reliably drive the complete downstream load or when regenerated edge behavior is preferable to continuing a lossy transmission-line segment. The principal design task is preserving the intended LVDS signal integrity at 800 Mbps. Use a controlled-impedance PCB layer, place the device close to the relevant connector or receiver, apply the termination scheme specified by the system architecture, and avoid unnecessary stubs. Power and ground pins should have low-impedance bypass connections close to the device. This page combines the verified Texas Instruments product information, distributor inventory references, package details, compatible orderable variants, and practical LVDS design guidance. It also distinguishes electrically equivalent catalog variants from true functional alternatives and identifies where detailed electrical, pricing, or lifecycle data still requires manufacturer confirmation.

RFQ پەیوەندی
DS90LV001TMX - 800 Mbps LVDS Buffer | Texas Instruments
DS90LV001TMX

DS90LV001TMX - 800 Mbps LVDS Buffer | Texas Instruments

The Texas Instruments DS90LV001TMX is an 800-Mbps LVDS-to-LVDS buffer designed for high-speed digital signal distribution across backplanes, cables, and multi-card systems. The device accepts an LVDS input and provides an LVDS output, helping isolate the source from the receiving load while preserving signal integrity. According to the Texas Instruments product page, the DS90LV001 is available in 8-pin WSON and SOIC packages, with an output-enable function that can place the LVDS output in TRI-STATE. An LVDS buffer is a digital interface component in the LVDS interface IC family. LVDS, or Low-Voltage Differential Signaling, uses low-amplitude differential voltage to transmit high-speed data with common-mode noise rejection and reduced electromagnetic emissions. A buffer placed in the signal path can extend usable distribution distance, isolate a transmitter from capacitive loading, and reduce the effect of imperfect terminations. The DS90LV001 family is therefore positioned between an LVDS transmitter and downstream LVDS receivers within the broader interface IC and semiconductor hierarchy. The principal electrical characteristic is an 800-Mbps data rate, suitable for high-speed backplane links, industrial control systems, communications equipment, and test platforms. The verified distributor description identifies the DS90LV001TMX as a single-channel LVDS buffer in an 8-SOIC package with an industrial temperature range from -40°C to +85°C. The output-enable pin allows the output to be disabled for bus sharing, controlled test modes, power-management schemes, or designs that need a high-impedance state during transitions. The device is designed to address signal-conditioning problems caused by transmission-line reflections, loading, and stub length. In large systems, the distance between a transmission line and an unterminated receiver on an individual card can limit system speed. A dedicated LVDS buffer can be placed near the receiver or at a card boundary to create a controlled signal path. Designers must still use suitable transmission-line geometry, correct source and load terminations, and a return-path reference to obtain reliable operation. Typical applications include LVDS backplane buffering, point-to-point high-speed links, industrial data acquisition, communications racks, and instrumentation platforms. The 800-Mbps capability makes the device appropriate for systems that need one LVDS signal to be redistributed or isolated without changing the underlying differential signaling format. The output-enable function is especially useful where multiple buffers share a bus or where the receiver must be disconnected during a controlled system state. When laying out a circuit using the DS90LV001TMX, place the device close to the source or receiver whose loading is being isolated. Route the differential pair as a controlled-impedance transmission line, keep the pair geometry consistent, and terminate the line according to the system architecture. Check the datasheet's absolute maximum ratings, supply recommendations, and propagation-delay information before finalizing a high-speed design. This page combines the manufacturer identification, package information, lifecycle status, verified distributor references, practical interface-design guidance, and a conservative comparison of available replacement information. It is intended to help engineers evaluate whether the DS90LV001TMX remains appropriate for an existing LVDS design or whether an alternate sourcing strategy is required.

RFQ پەیوەندی
DS90LV001TMX/NOPB - 800 Mbps LVDS Buffer | Texas Instruments
DS90LV001TMX/NOPB

DS90LV001TMX/NOPB - 800 Mbps LVDS Buffer | Texas Instruments

The Texas Instruments DS90LV001TMX/NOPB is a single-channel LVDS-to-LVDS buffer / re-driver that supports signaling rates up to 800 Mbps in an 8-pin SOIC (D) package with an exposed thermal pad area. The device takes a standard LVDS input signal and re-transmits an LVDS signal at the output, while operating from a single 3.3 V supply (3.0 V to 3.6 V) and consuming roughly 70 mA of supply current. It is qualified across the -40 C to +85 C industrial temperature range and is supplied in a tape-and-reel SOIC-8 package on a 3.90 mm body width. An LVDS buffer (Low-Voltage Differential Signaling buffer / re-driver) is a type of high-speed differential interface IC that regenerates and re-shapes a weak or distorted differential signal so it can drive another transmission line segment. In the broader system hierarchy it sits under interface ICs, then signal-conditioning devices, and ultimately under wired-connectivity semiconductors. LVDS buffers are essential building blocks in any system where the original LVDS transmitter cannot source enough current to reach a distant receiver while still meeting the TIA/EIA-644 eye-diagram mask. Key features of the DS90LV001TMX/NOPB include a 2.0 ns typical propagation delay, low jitter and low skew design that holds the differential output within tight limits, integrated 100 ohm input termination across the LVDS input pair, and an LVDS output stage that supports both point-to-point and multi-drop topologies. The device is designed to accept LVPECL inputs when AC-coupled, giving it cross-standard compatibility within the same SOIC-8 footprint. A single channel is provided per package, and the part is pin-to-pin compatible with the rest of the DS90LV001 family. Architecturally, the DS90LV001 uses a current-mode LVDS driver with on-chip bias generation. The differential receiver detects the incoming signal and re-times it through an internal logic stage that drives the output current-steering network. Because the part is a transparent buffer, it does not add protocol encoding or clock-data recovery - it simply regenerates the differential edge, restoring amplitude and common-mode level so the signal can traverse another cable, connector, or FR-4 stub. Typical applications for the DS90LV001TMX/NOPB include clock distribution across backplanes, buffering LVDS links between mezzanine cards, extending FR-4 trace runs in telecom and networking line cards, cable driving in point-to-point LVDS links, and acting as a stub-length isolator in large distributed systems where the unterminated stub length would otherwise limit the maximum achievable data rate. Designers also use it as a fan-out repeater when one LVDS source must drive two downstream loads. A key design consideration is the placement of external AC-coupling capacitors when LVPECL sources must be interfaced - these capacitors must be placed close to the device inputs to control the common-mode voltage. The DS90LV001's 8-pin SOIC footprint keeps the layout small but thermal performance is modest, so for applications that require higher output drive or multi-channel operation a higher-current or multi-channel LVDS part from the same family should be considered. This page synthesizes distributor stock, drop-in SOIC-8 alternatives, and practical PCB-layout notes not found in the manufacturer datasheet.

RFQ پەیوەندی
DS90LV004TVS - 4-Channel 1.5 Gbps LVDS Repeater | Texas Instruments
DS90LV004TVS

DS90LV004TVS - 4-Channel 1.5 Gbps LVDS Repeater | Texas Instruments

The Texas Instruments DS90LV004TVS is a four-channel 1.5 Gbps LVDS buffer and repeater in a 48-pin TQFP package measuring 7 x 7 mm. The device provides four high-speed differential data channels with configurable pre-emphasis for compensating signal degradation caused by lossy backplanes and cables. Its flow-through pin arrangement supports straightforward board layout and helps minimize internal device jitter. An LVDS repeater is a signal-conditioning semiconductor that receives differential low-voltage digital signaling and retransmits it across a channel. LVDS belongs to the differential interface hierarchy used for reliable high-speed data transfer over printed-circuit-board traces and balanced cables. The repeater function can restore signal integrity, isolate the source from the receiving endpoint, and extend usable distance across a lossy interconnect when the complete channel remains within the device's 1.5 Gbps capability. The DS90LV004TVS offers four independent channels, operation at 1.5 Gbps, configurable pre-emphasis, and a flow-through pinout. These features make it relevant to parallel data links where channel-to-channel skew, ringing, and pulse-width degradation must be controlled. Its differential inputs can interface with LVDS and Bus LVDS signals, including signaling used by compatible TI SerDes designs. This device is categorized as an interface IC rather than a general-purpose logic IC. Its primary function is to preserve the integrity of high-speed differential signals rather than perform computation or protocol conversion. A flow-through package arrangement can reduce routing complexity by allowing signals to pass through the device in a consistent direction, which is especially useful when multiple channels must cross a board or equipment boundary. Typical applications include LVDS-to-LVDS signal conditioning across a backplane, data acquisition systems, industrial control equipment, communications equipment, and test and measurement instruments. The configurable pre-emphasis is particularly useful when a PCB trace or cable introduces high-frequency attenuation that produces inter-symbol interference. Designers should determine the required emphasis from measured channel response rather than assuming the maximum setting is appropriate. A critical design consideration is maintaining a continuous, controlled-impedance LVDS signal path through the device. Input and output routing, return-plane continuity, decoupling, connector transitions, and external termination must be evaluated together. The 48-TQFP package also requires attention to exposed thermal behavior when the repeater is operated continuously at the upper end of its 1.5 Gbps capability. This product page organizes the confirmed electrical identity, package information, sourcing route, comparison considerations, and design guidance for the DS90LV004TVS. It also distinguishes direct ordering variants from functionally similar interface devices so engineers can distinguish a true board-level replacement from a merely related LVDS component.

RFQ پەیوەندی
DS90LV011ATMFX - 400Mbps LVDS Driver | Texas Instruments
DS90LV011ATMFX

DS90LV011ATMFX - 400Mbps LVDS Driver | Texas Instruments

Texas Instruments DS90LV011ATMFX is a 400-Mbps LVDS single high-speed differential driver packaged in a 5-pin SOT-23 (DBV) package. It is designed for point-to-point, low-voltage differential signaling over balanced interconnects, where a small package, high data rate, and robust differential output are important. The device supports a -40°C to +85°C operating temperature range according to the manufacturer product listing, and the related automotive-qualified variant extends the range to +125°C. An LVDS driver is a specialized interface-circuit component that converts a low-voltage digital input into a balanced differential output. In the broader electronics hierarchy, it belongs to the interface IC category and supports high-speed communication between processors, FPGAs, display controllers, serializers, and test equipment. Differential signaling improves noise immunity by rejecting common-mode disturbances that can affect single-ended links. Key characteristics include a 400-Mbps data rate, single differential output configuration, and a compact SOT-23-5 package. The DS90LV011A family is intended for systems requiring short-reach, high-speed point-to-point links. Its small footprint makes it suitable for space-constrained boards, while the differential output helps maintain signal integrity over controlled PCB traces or suitable cable interconnects. The DS90LV011A uses a 3 V LVDS single high-speed differential driver architecture. Compared with a single-ended output, the differential arrangement uses two complementary conductors, reducing sensitivity to common-mode voltage and radiated noise. The interface should be designed around the manufacturer’s recommended terminations, controlled trace geometry, proper grounding, and a continuous reference plane. Typical uses include high-speed backplanes, FPGA-to-FPGA links, serializer connections, display-interface links, industrial control links, and embedded communication modules. The device is particularly appropriate when the receiver supports LVDS and the link distance is short enough for the intended signaling environment. A key design consideration is that the SOT-23-5 package requires careful layout around the differential outputs. Keep the pair of differential traces coupled, use matched length where timing margins require it, provide a solid ground reference, and place any receiver-side termination close to the receiving device. Use the Request a Quote form on this page to confirm current commercial availability, lead time, and ordering details.

RFQ پەیوەندی
DS90LV012ATMFX - 400 Mbps LVDS Receiver | Texas Instruments
DS90LV012ATMFX

DS90LV012ATMFX - 400 Mbps LVDS Receiver | Texas Instruments

The Texas Instruments DS90LV012ATMFX is a 3-V LVDS single CMOS differential line receiver designed for high-speed digital interfaces. It accepts low-voltage differential signals, with a typical differential input level of 350 mV, and translates them into 3-V CMOS output levels. The receiver supports data rates up to 400 Mbps and is supplied in a 5-pin SOT-23 package, making it suitable for compact point-to-point communication equipment. A low-voltage differential signaling receiver is an interface IC that converts a small differential voltage between two conductors into a single-ended CMOS logic signal. LVDS belongs to the broader differential line-driver and line-receiver family within interface ICs. Its differential signal method improves noise immunity by comparing the voltage on a positive input with the voltage on a negative input, which helps preserve data integrity when signals are transmitted across cables, backplanes, or circuit-board interconnects. The DS90LV012ATMFX is intended for systems requiring low power dissipation, low noise, and high data rates. The manufacturer describes the device as a single CMOS differential-line receiver capable of operating in excess of 400 Mbps, corresponding to approximately 200 MHz. Its 3-V CMOS output interface makes it suitable for connecting LVDS physical-layer links to digital logic, controllers, FPGAs, ASICs, and other CMOS-based systems. The receiver family provides fail-safe behavior for open, shorted, and terminated input conditions. Under those fail-safe conditions, the receiver output remains HIGH. This behavior helps system designers establish a defined state when a cable is disconnected, improperly terminated, or otherwise faulted. The DS90LV012A family also uses a pinout intended to simplify PCB layout, while the related DS90LT012A includes an input line-termination resistor for point-to-point applications. Typical uses include industrial control links, test and measurement equipment, video and data transmission interfaces, embedded systems, and communications equipment. When placing the receiver in a design, preserve the differential pair geometry between the source and receiver, maintain suitable return paths, and follow the manufacturer’s input termination and bypass recommendations. The device must also be evaluated against the system’s required data rate, voltage levels, propagation-delay budget, and fault-state expectations. This page combines the manufacturer’s device description, ordering information, package information, and cross-reference information into an application-focused guide. It highlights the distinction between the standard LVDS receiver and the related terminated DS90LT012A, clarifies the role of the SOT-23-5 package, and identifies the technical checks required before using DS90LV012ATMFX as a replacement candidate.

RFQ پەیوەندی
DS90LV017ATM - 600Mbps LVDS Driver | Texas Instruments
DS90LV017ATM

DS90LV017ATM - 600Mbps LVDS Driver | Texas Instruments

The Texas Instruments DS90LV017ATM is a single high-speed differential LVDS driver with data rates above 600 Mbps, equivalent to 300 MHz, in an 8-pin SOIC narrow package. It uses a 3.3 V supply, supports an operating temperature range from -40°C to 85°C, and is designed for low-power, high-speed point-to-point signal transmission. Its current-mode architecture maintains low power dissipation as operating frequency rises while also minimizing short-circuit fault current. An LVDS driver is a low-voltage differential-signaling interface circuit that converts a single-ended logic signal into two complementary differential outputs. LVDS belongs to the broader signal-interface and interface-IC hierarchy, where differential current-mode signaling reduces sensitivity to common-mode noise and supports reliable data transmission across printed-circuit-board traces or balanced cables. The differential outputs allow a receiver to interpret the voltage difference between the two conductors, improving noise immunity in systems operating at high data rates. The DS90LV017A family is optimized around three principal characteristics: operation above 600 Mbps, low power consumption, and controlled short-circuit fault current. The current-mode output stage is especially important at high frequencies because it avoids the rising power dissipation commonly associated with voltage-mode drivers. The manufacturer identifies the device as a single differential driver, making it useful when one channel is required without the channel count and pin count of a quad driver. The interface complies with the EIA-644-A and TIA-644-A technologies identified for this device family. Its operating characteristics are suited to high-speed point-to-point links in test equipment, industrial control, communications infrastructure, video systems, and data-acquisition equipment. In each case, the differential signaling method supports rapid data transfer while the low-power current-mode implementation helps manage system heat and board-space requirements. When laying out a circuit using the DS90LV017ATM, treat the two differential outputs as a controlled impedance pair. Route them together with matched geometry, minimize stubs, and provide the decoupling and return-path structure required by the manufacturer's application guidance. Keep the signal path away from unrelated switching nodes, because differential signaling improves common-mode rejection but does not eliminate sensitivity to coupled noise or impedance discontinuities. This product page combines the manufacturer's interface description, package and operating information, pricing structure, replacement guidance, and practical PCB implementation notes. It also distinguishes true same-footprint alternatives from related multi-channel LVDS devices, helping engineers evaluate upgrade paths without assuming that a related family member is electrically or mechanically interchangeable.

RFQ پەیوەندی