Logic ICs
بەرهەمەکان (720+)
CD4020BPW - 14-Stage CMOS Counter Divider | Texas Instruments
Texas Instruments CD4020BPW is a CMOS 14-stage ripple-carry binary counter and divider with one counter element, negative-edge triggering, and a 16-pin TSSOP package rated for operation from -55°C to 125°C. The counter advances one binary count for each active clock transition, allowing a single external clock to generate divided, modulo-2^N timing relationships. A CMOS ripple-carry counter is a logic-IC counter in which cascaded flip-flop stages advance sequentially. It belongs to the counter and divider hierarchy within digital logic ICs, where counters divide an input frequency and provide repeating binary sequences. The CD4020BPW supports the classic CD4000-series function while using a surface-mount TSSOP-16 footprint for compact PCB layouts. The primary functional characteristics are a 14-stage count capacity, binary counting behavior, negative-edge clock triggering, and one counting element. Its serial output provides access to a divided clock derived from the input frequency. Because it is a ripple-carry implementation, the output stages do not switch simultaneously; designers should account for propagation delay when using closely related outputs as counter-phase signals. The CD4020BPW uses CMOS logic and operates across a wide -55°C to 125°C temperature range. Its 16-pin TSSOP package is identified as 0.173 inch, or 4.40 mm, wide. The PW orderable variant is associated with tube packaging, making it suitable for production processes that use tubes and accept the corresponding MSL handling requirements. Typical uses include digital frequency division, clock generation, timing-event counting, industrial control logic, and low-power CMOS instrumentation. The device is useful when a circuit needs multiple binary-derived timing points or a stable divided clock without implementing a programmable counter in a microcontroller or FPGA. PCB implementation should reserve the correct clock, reset, supply, and output connections according to the manufacturer pin-description table. Keep the clock trace short, provide a stable supply reference, and avoid relying on simultaneous transitions from different ripple stages where timing skew would affect control logic. This page combines the manufacturer product definition, distributor package information, ordering details, and engineering guidance for the CD4020BPW. It also identifies where second-source and same-footprint alternatives require independent verification, helping engineers evaluate counter implementations without confusing different package variants with true drop-in equivalents.
CD4022BCN - 3-15V CMOS Divide-by-8 Counter | onsemi
The onsemi CD4022BCN is a CMOS 4-stage divide-by-8 Johnson counter with eight decoded outputs and a carry-out bit, designed for a 3.0 V to 15 V supply range. The device is a 1-element, 4-bit, positive-edge-triggered binary counter housed in a 16-PDIP package. A Johnson counter is a shift-register-based counter that advances through a fixed sequence of states and provides one decoded output for each state. The CD4022BCN belongs to the CD4000 CMOS logic family, where CMOS logic ICs use complementary metal-oxide-semiconductor circuitry to support low-voltage operation. Within the broader hierarchy, it is a counter IC and divider within digital logic ICs. The principal features include eight decoded outputs, a carry-out bit, positive-edge clock triggering, and operation from 3.0 V to 15 V. The carry output provides a divide-by-8 carry indication, allowing cascaded counters to implement larger multiples of eight. Its decoded outputs are useful when a system must activate one of eight positions or channels in sequence. The CD4022BCN implements a four-stage Johnson shift register. Each positive clock edge shifts data through the register, and the decoded outputs follow the counter sequence. Because the device operates from the same 3.0 V to 15 V range as other CD4000-series logic, it can be combined with compatible CMOS gates, flip-flops, decoders, and timing circuits without requiring a separate high-voltage logic family. Typical uses include eight-step sequencers, modulo-8 frequency dividers, timing generators, industrial control logic, and digital channel-selection circuits. An oscillator can drive the clock input when a variable or adjustable repetition rate is required, while the carry output can clock another counter when a higher division ratio is needed. PCB design should preserve the standard 16-pin DIP pinout and provide adequate bypass capacitance close to the supply pins. Designers should also account for unused decoded outputs, clock-edge requirements, and the propagation delay between the clock edge and decoded-output transitions when sequencing time-sensitive external circuitry. This product page consolidates the core electrical identity, verified package information, sourcing guidance, comparison parameters, and practical implementation considerations for engineers evaluating the CD4022BCN as a drop-in 16-PDIP counter.
CD4022BD3 4-Bit Binary Counter | Harris Corporation
The Harris Corporation CD4022BD3 is a 4-bit binary counter IC with one counter element, positive-edge counting, and a 16-CDIP package. According to the manufacturer-related listing, the device operates across a 3 V to 18 V supply range and supports counting frequencies up to 11 MHz. Its counter outputs provide a practical divide-by-2, divide-by-4, divide-by-8, and divide-by-16 sequence for digital control, timing, sequencing, and frequency-division circuits. The CD4022BD3 belongs to the CMOS CD4000 logic family, combining low-voltage operation with wide supply-voltage tolerance and conventional through-hole DIP construction. A binary counter is a sequential digital circuit that records successive binary states at each active clock transition. The CD4022BD3 advances on the positive edge of the clock signal and provides four parallel output bits, Q0 through Q3. Its architecture makes it useful when a system needs a compact modulo-16 counting sequence rather than the decade counting arrangement used by a modulo-10 counter. The reset input allows the count to be initialized to a known state, while the carry output can be used to indicate the terminal count and trigger another counting stage. The 16-CDIP package is mechanically suitable for through-hole PCB assembly, prototyping, repair, and legacy industrial equipment. Its lead spacing provides generous creepage between adjacent pins, which is useful when the logic operates near the upper end of the 3 V to 18 V supply range. The counter’s positive-edge triggering makes board-level integration straightforward: connect the clock source to the clock pin, route the four count outputs to the receiving logic, and use the reset and carry signals for initialization and cascading. Decoupling close to the supply pins remains important even though the broad operating-voltage range is a principal feature of the CD4000 family. The CD4022BD3 is appropriate for digital frequency dividers, programmable timing chains, industrial sequence controllers, pulse-counting modules, and older control systems that use CD4000-series CMOS logic. The 11 MHz maximum counting frequency allows the counter to divide substantially faster than ordinary low-frequency control signals, although actual system operation must respect the supply voltage, output loading, signal transition times, and external reset timing. For designs requiring a different package, pin function, or logic family, compare the manufacturer’s CD4022 documentation and the original system schematic before substituting a part. This product page organizes the CD4022BD3 around its verified counter function, supply range, package, and timing characteristics, while also identifying the design constraints that matter when replacing a legacy Harris counter. Use the manufacturer datasheet and the original equipment documentation for final pin assignments, electrical limits, and qualification decisions before committing a new PCB design.
CD4022BE - 4-Stage CMOS Octal Counter | Texas Instruments
Texas Instruments CD4022BE is a 4-stage CMOS Johnson counter with 8 decoded outputs, operating from a 5 V, 10 V, or 15 V parametric rating and delivering medium-speed operation with a typical clock frequency of 10 MHz at VDD = 10 V. The device is packaged in a 16-lead plastic dual-in-line package identified as 16-PDIP. A counter IC is a synchronous or asynchronous digital logic device that advances an internal binary state when it receives a clock transition. A CMOS counter belongs to the logic IC family and is commonly used to divide an input frequency, generate sequential timing signals, or sequence multiple digital operations. The Johnson configuration in the CD4022B uses four internal stages and presents eight decoded outputs. Its decade-counter behavior provides eight active states, while the associated clock, reset, and clock-inhibit inputs control counting, initialization, and temporary stopping of the count sequence. The principal operating features include fully static operation, standardized symmetrical output characteristics, and a typical operating frequency of 10 MHz at VDD = 10 V. The CD4022BE family is specified with 5 V, 10 V, and 15 V parametric ratings. Its quiescent-current production test is performed at 20 V, providing a defined screening condition for one of the most important static-power parameters of a CMOS counter. The architecture uses positive-edge clocking and includes CLOCK, RESET, and CLOCK INHIBIT control inputs. Decoded outputs support applications that require mutually exclusive active states rather than a raw binary count bus. RESET establishes the starting count state, while CLOCK INHIBIT provides a direct control for preventing further state transitions. The logic operates from a supply and includes a 16-PDIP package intended for through-hole PCB assembly. Typical uses include modulo-8 frequency division, eight-step sequencing, digital timing generation, programmable counters, industrial control logic, and embedded systems that need a compact eight-state sequence. In these circuits, the CD4022BE can reduce a repeated input pulse into a lower-frequency sequence while the eight decoded outputs provide mutually exclusive timing phases for sequential control or display-related functions. Designers should account for the required supply voltage, input and output logic levels, clock pulse timing, and power behavior. Because RESET and CLOCK INHIBIT are active control functions, their inactive states must be defined and their transitions coordinated with the clock. The through-hole 16-PDIP footprint also requires adequate board spacing, appropriate pin alignment, and observation of the component pin-1 marking during assembly. This product page combines the Texas Instruments CD4022B family characteristics, verified package information, sourcing data, application guidance, and a conservative drop-in replacement assessment. The comparison and design notes focus on the counter architecture, timing behavior, supply conditions, and PCB implementation considerations that help engineers evaluate the CD4022BE before incorporating it into a new circuit.
CD4022BF 4-Bit CMOS Octal Counter | Texas Instruments
The Texas Instruments CD4022BF is a CMOS 4-bit octal counter with eight decoded outputs, supplied in a 16-pin CDIP package. It operates across a -55°C to +125°C temperature range and is intended for frequency division, sequential state generation, and digital timing applications. The device accepts a clock, reset, and clock-inhibit input, while its clock input uses Schmitt-trigger action to provide improved pulse shaping. A Johnson counter is a type of sequential digital counter that advances through a fixed sequence of states and is commonly used when one decoded output must be active for each count. The CD4022B family provides four counter stages and eight decoded outputs, making it suitable for dividing an input frequency into eight repeating sections or creating an eight-step sequence. Its CMOS architecture places it within the broader hierarchy of counter/divider logic, digital logic IC, and semiconductor categories. The principal electrical features include support for typical 3.3 V, 5 V, 9 V, 12 V, and 15 V operating supplies, with a minimum operating supply voltage of 3 V. The decoded outputs simplify sequencing by eliminating a binary-to-decimal decoder. Clock-inhibit provides a way to hold or disable further counting, while reset establishes a defined starting condition. The Schmitt-trigger clock input helps accommodate slower or noisy input transitions without relying on a conventional TTL-style threshold. The CD4022BF is offered in a 16-lead CDIP package and is supplied in a tube. Its broad temperature range makes it suitable for industrial control, instrumentation, legacy automation, and other systems requiring operation across extended environmental conditions. Because it is a CMOS counter, correct handling of unused inputs and power sequencing remains important in designs that combine it with newer digital devices. For circuit implementation, connect the clock source to the clock input, drive reset and clock inhibit to defined logic levels during normal operation, and route the decoded outputs to the loads or control logic that require sequencing. Verify that the input voltage levels are compatible with the selected supply voltage. Do not leave CMOS control inputs floating, because an undefined input state can cause unwanted counting or increased supply current. A primary engineering trade-off is that the CD4022BF is a conventional through-hole logic device rather than a modern low-voltage surface-mount counter. Its broad supply-voltage range and temperature rating are useful for established control systems, but newer designs may prefer smaller packages, lower supply current, or higher switching performance. The CDIP package also requires more board area than SOIC or TSSOP alternatives. This page combines the device description, package and environmental information, drop-in alternatives, comparison parameters, application guidance, and practical design notes. These details support schematic review, footprint confirmation, lifecycle planning, and replacement assessment without replacing the manufacturer datasheet or application-specific qualification.
CD4022BF/3 - CMOS Octal Counter | Harris Corporation
The Harris Corporation CD4022BF/3 is a CMOS octal counter with eight decoded outputs, supplied in a 16-lead ceramic DIP package for -55°C to 125°C operation. It provides four independent decoded outputs for divide-by-2, divide-by-4, divide-by-8, and divide-by-10 counting functions, together with clock, reset, and carry control signals. A CMOS counter is a digital logic IC that advances an internal binary state on each active clock edge and exposes selected states through decoded outputs. The CD4000-series hierarchy places this device within CMOS logic, counter and divider circuits, and ultimately within the broader integrated-circuit and digital-logic categories. Its decoded outputs reduce the external logic required when a system needs several division ratios from one clock source. The CD4022BF family supports typical operating supply values of 3.3 V, 5 V, 9 V, 12 V, and 15 V. The 16-CDIP package provides generous lead spacing for through-hole assembly and is suitable for legacy industrial, control, instrumentation, and test equipment where stable operation over an extended temperature range is important. The ceramic DIP construction also differentiates this packaged device from modern plastic small-outline implementations. The octal counter architecture includes a clock input, reset control, carry output, and four decoded outputs. Reset behavior and active clock-edge requirements must be followed exactly when connecting external control logic. Because decoded counter outputs can change several timing relationships during rollover, circuits that cascade multiple counters should account for propagation delay and reset recovery behavior. Typical uses include frequency division, programmable timing generators, sequential control logic, digital clocks, event-counting modules, and industrial test equipment. The eight-output organization makes the device useful when several divide stages must be observed simultaneously, while the carry output can provide a higher-order count indication for cascaded arrangements. For a new through-hole design, verify the exact pin assignment, supply-voltage limits, and timing values in the manufacturer datasheet before releasing the PCB. Keep clock and reset traces short, provide a stable supply reference, and avoid routing high-current switching signals adjacent to counter inputs to reduce contamination of transition timing. This page consolidates the available technical information, sourcing guidance, cross-brand replacement context, and practical integration considerations for engineers evaluating the CD4022BF/3. It is intended to support design selection and PCB planning rather than replace the manufacturer’s complete electrical characteristics and test data.
CD4024AD3 - 7-Bit CMOS Binary Counter | Harris | CDIP-14
The Harris Corporation CD4024AD3 is a 7-bit asynchronous, negative-edge-triggered, up-counting binary counter built with CMOS logic and supplied in a 14-pin CDIP package. It operates across a 3 V to 12 V supply range and provides one counter element with seven binary output stages. The device belongs to the 4000, 14000, and 40000 CMOS logic family, where a counter is a sequential logic circuit that changes its binary state when triggered. A binary counter is a type of counter IC that stores and advances a multi-bit binary number. The CD4024AD3 uses an asynchronous ripple-carry counting architecture: each output stage changes after the preceding stage, allowing successive binary states to appear across the seven outputs. Negative-edge triggering means the count advances on the high-to-low transition of the clock input rather than its low-to-high transition. This behavior must be considered when defining reset timing and external clock-conditioning circuits. The principal features of the CD4024AD3 include seven counter outputs, negative-edge clock triggering, asynchronous counting, and operation from 3 V to 12 V. Because it uses CMOS technology, the circuit is suitable for low-voltage digital systems in which supply current, logic thresholds, and integration density are important considerations. The parallel binary outputs provide a direct representation of the current count from 0 through 127, simplifying connections to displays, decoders, programmable controllers, or other digital subsystems. The 14-CDIP package provides through-hole access to the counter, clock, reset, and output functions. Its lead spacing supports conventional PCB layouts and socketed assemblies rather than fine-pitch surface mounting. Pin assignments should be taken from the Harris CD4024AD3 datasheet when assigning PCB tracks, especially because adjacent counter stages may be brought out in a non-sequential physical order. The asynchronous ripple architecture is straightforward for low-to-moderate clock rates, but propagation delay accumulates through the seven stages and should be checked against the maximum system clock requirement. Typical uses include digital frequency division, event-counting modules, timing dividers, industrial control logic, laboratory counters, and educational digital-logic systems. The part can divide an incoming pulse train by 2, 4, 8, 16, 32, 64, or 128 by observing the corresponding output stage. It is also useful when a controller requires a binary state that can be read in parallel rather than decoded from a one-hot sequence. For reliable circuit design, use a clean clock edge and account for cumulative ripple delay before using the most significant output as a high-frequency timing reference. Reset should be asserted long enough to establish a defined starting state, and unused inputs must be held at valid CMOS logic levels. Because a CDIP package exposes long leads, pay particular attention to lead clearance, soldering temperature, and protection from electrostatic discharge during handling. This product record combines the verified Harris CD4024AD3 ordering description, electrical classifications, package information, sourcing observations, and practical implementation guidance. It also identifies where a true pin-compatible replacement must be confirmed instead of treating a functionally similar counter as an automatic drop-in substitute. Engineers can use the comparison and validation guidance below to evaluate board-level compatibility, timing margins, lifecycle risk, and sourcing requirements before approving an alternative.
CD4024AK3 - 7-Bit CMOS Binary Counter | Harris Corporation
The Harris Corporation CD4024AK3 is a 7-bit asynchronous, ripple-carry CMOS binary counter with negative-edge triggering and up-counting operation in a 14-pin PDSO package. It provides 128 count states, seven parallel binary outputs, and separate clock, reset, and carry connections. The part belongs to the CD4000 CMOS logic family and is intended for digital counting, frequency division, state sequencing, and timing applications. A CMOS binary counter is a synchronous-state logic device that advances through a predetermined sequence when triggered by an external clock. The CD4024AK3 is an asynchronous ripple counter, meaning each internal stage transitions in sequence after the preceding stage. Its negative-edge clock triggering makes the count change on the falling transition of the clock signal, while the parallel output pins expose the current seven-bit count. Key features include 7-bit counting capacity, 128 selectable states, negative-edge triggering, and operation as a single one-element counter element. The output count advances in the up direction from binary 0000000 through 1111111. A dedicated reset input initializes the counter, and the carry output provides an indication that the terminal count has been reached. These functions support binary-frequency division, programmable timing chains, and repeatable event sequencing. The CD4000-series architecture uses CMOS logic, allowing operation from the same supply rail as the surrounding digital system while producing complementary outputs. Because the counter contains cascaded internal stages, propagation delay accumulates through the chain. Designers should include this accumulated delay when determining maximum clock frequency or when using the carry output to trigger downstream circuitry. Typical applications include digital time-base generation, sequential industrial controls, test-equipment pulse counting, frequency division, repetitive-event indexing, and programmable control logic. The seven outputs can directly represent a binary state or feed multiplexers, decoders, display drivers, and memory address logic. Negative-edge triggering also allows several counters to be cascaded while maintaining predictable event timing. For reliable implementation, connect unused inputs to defined logic levels, observe the power-supply limits and absolute maximum ratings in the manufacturer datasheet, and account for package-specific lead assignments. The reset path should be kept free from long traces or noisy nodes because it establishes the starting state for every counting cycle. Decoupling near the supply pins helps reduce logic noise and false transitions in cascaded arrangements. This product reference combines the device architecture, package identity, practical design guidance, structured commercial inquiry, and verified source links into a concise engineering selection resource for counter and timing applications.
CD4024AT - 3V-12V CMOS Binary Counter | Texas Instruments
Texas Instruments CD4024AT is a CMOS ripple-carry binary counter divider designed for digital counting, frequency division, sequencing, and state-machine applications. The device operates from 3V to 12V and is packaged in a 14-pin CDIP package. Its military temperature grade identifies it as a ruggedized logic option for equipment requiring a through-hole counter in a conventional dual in-line footprint. A CMOS ripple-carry binary counter is a digital logic IC that advances through a sequence of binary states when driven by an active clock edge. The broader hierarchy runs from counter and divider logic to digital logic, integrated logic, and semiconductor. Unlike asynchronous binary ripple counters, the CD4024 family includes reset and parallel data inputs that allow the count state to be loaded or cleared for deterministic system operation. The CD4024AT combines a 3V to 12V supply range with a 14-pin CDIP package. The counter architecture supports use in digital clocks, industrial timing circuits, programmable dividers, and digital control systems. Its through-hole package also makes it practical for prototypes, repair assemblies, and industrial equipment where a socketed or leaded logic package is easier to assemble than a fine-pitch surface-mount device. The part belongs to the CD4000 CMOS logic family, whose members use complementary metal-oxide-semiconductor technology. Operation from 3V to 12V places the device across common low-voltage logic environments, while the 14-pin through-hole format favors larger assemblies rather than compact handheld products. Engineers should consult the manufacturer datasheet for detailed truth tables, clock-edge behavior, output configuration, reset behavior, and electrical limits before finalizing a design. Typical uses include binary event counting, divide-by-n timing generation, sequential control, industrial counters, and clocked digital subsystems. In a divider implementation, the counter output can define a lower-frequency timing event while external logic determines the useful modulus. In a sequencing system, reset and parallel-load functions allow a known starting state, which helps prevent an undefined count after power-up or fault recovery. The primary design consideration is ensuring that clock, reset, and data inputs remain within their specified voltage and transition-time limits. PCB layout should keep clock routing short, provide a stable ground reference, and separate clock paths from sensitive analog or high-current switching nodes. Because this is a legacy-style CDIP logic device, designers should also confirm available package details and sourcing status before committing a new production design. This page combines the verified CD4024AT identity, manufacturer-oriented documentation references, package information, design guidance, application analysis, and substitution constraints. It also distinguishes documented attributes from parameters that require confirmation from the datasheet, helping engineers evaluate the CD4024AT without assuming unpublished electrical limits or unqualified replacements.
CD4024BCM - 7-Bit Binary Counter | onsemi | SOIC-14
The onsemi CD4024BCM is a single-element, 7-bit binary counter with negative-edge triggering, packaged in a 14-pin SOIC. It advances a seven-bit count sequence on each selected clock transition and provides a compact counter stage for digital control, timing, sequencing, and frequency-division circuits. The 14-SOIC package supports conventional surface-mount PCB assembly while retaining the industry-standard CD4024 counter function. A binary counter is a sequential digital circuit that stores and advances a count represented in binary form. Within the logic-IC hierarchy, the CD4024 belongs to the counter and divider class, combines CMOS switching characteristics with ripple-carry binary counting, and serves as a fundamental building block for digital state machines, event counters, programmable timing modules, and low-frequency divider chains. The principal identified features are one independent 7-bit counting element, negative-edge clock triggering, binary counter operation, and a 14-SOIC package. Negative-edge operation means the count advances on the falling clock transition rather than the rising transition, making the device useful when a system derives its timing reference from the falling edge of a periodic waveform. The single-element organization also allows cascading multiple packages when a wider count range or additional divided outputs are required. The counter architecture supports straightforward chaining because its parallel binary outputs can feed the clock input of a following stage. Cascading increases the available count range and permits division of an input clock by a greater power of two when each stage supplies one additional binary bit. Designers should pay close attention to clock-edge requirements, propagation delay through the ripple-carry path, reset timing, and the voltage levels presented to the inputs when combining this part with other CMOS logic families. Typical applications include digital frequency division, pulse-counting modules, programmable sequencing controllers, industrial timer interfaces, clock-generation blocks, and embedded automation logic. The device is particularly appropriate when a compact seven-bit counter is needed without the complexity of a microcontroller. In such systems, external gating can define the counted interval, while the parallel outputs expose the count for display, control, or comparison with another digital subsystem. The principal design consideration is ensuring that every clock, reset, and data input remains within the electrical limits specified by the manufacturer. Layout should minimize clock-node capacitance and keep high-current switching loops away from counter output traces to reduce coupling into the least-significant count bit. Power-supply decoupling close to the package and deliberate grounding are important when the output is used to control nearby analog, communication, or timing circuitry. This product page combines the exact CD4024BCM identity with package-specific guidance, application-oriented counter examples, drop-in replacement options, and engineering selection criteria. It is intended to help engineers identify the correct counter, verify pin and package compatibility, and integrate the device without overlooking edge-triggering, reset, timing, or layout requirements.
CD4024BCN - 7-Bit Ripple Binary Counter | onsemi
The onsemi CD4024BCN is a CMOS 7-stage ripple-carry binary counter with buffered outputs, a negative-edge clock, and a master reset input in a 14-pin MDIP package. It operates from 3 V to 15 V and provides seven individually accessible count outputs for binary counting, frequency division, sequencing, and state-machine implementations. The counter advances on the negative transition of each clock pulse and is returned to logic zero by a logic-high reset input. A binary counter is a sequential digital circuit that stores a count as a set of binary bits and advances that count when triggered. A ripple-carry counter implements the stages in sequence, so each stage clocks the following stage. The CD4024BCN belongs to the CD4000 CMOS logic family, combining counters into the broader category of logic ICs, clock and timing circuits, and digital semiconductors. The principal features include seven counter stages, externally buffered outputs from stage 1 through stage 7, a negative-edge-triggered clock, and a direct master-reset function. Its 3 V to 15 V supply range permits operation from conventional 5 V logic systems through higher-voltage CMOS rails. Buffered stage outputs allow each count bit to be used without directly driving an additional counter stage through an external buffer. CD4000-series CMOS devices use positive and negative supply rails, and the CD4024BCN includes a standard 14-pin DIP-style interface. Because the internal stages form a ripple chain, cumulative propagation delay across all seven stages can affect the time available for the final output to settle after a clock transition. Applications with high-frequency requirements must therefore account for both the counter operating frequency and the settling requirement of the particular output bit being sampled. Typical uses include divide-by-2 through divide-by-128 clock generation, event counting, industrial timing, programmable sequencing, digital test equipment, and general-purpose logic control. The reset input allows the counter to establish a known starting state before counting begins. In a divide-by-N arrangement, one or more of the seven outputs can be combined so that the active-low transition of the selected bit establishes the repetition rate. For reliable implementation, keep the clock source clean and respect the input and output timing limits stated in the manufacturer datasheet. Provide adequate bypassing across the supply pins, especially when the counter drives external control logic or long signal routes. Confirm reset release timing relative to the active clock edge so that reset noise or a slowly changing reset edge does not create an unintended count event. This page combines functional interpretation, practical design guidance, pin-level implementation details, drop-in replacement analysis, and parameter-by-parameter comparison. It is designed to help engineers evaluate the CD4024BCN for legacy CMOS, industrial, educational, control, and timing applications without overlooking reset behavior, ripple delay, supply-voltage compatibility, or package-level replacement constraints.
CD4024BE - 7-Bit CMOS Ripple Counter | Texas Instruments
Texas Instruments CD4024BE is a CMOS 7-stage ripple-carry binary counter and divider with seven binary outputs, a negative-edge-triggered clock input, and a high-level reset function. It operates across a 3 V to 18 V supply range and is packaged in a 14-pin PDIP. The counter advances on the negative transition of each clock pulse, allowing the part to divide an input frequency by powers of two through the Q0 through Q6 outputs. A binary ripple counter is a digital logic IC that stores a multi-bit count using interconnected flip-flop stages. CD4000-series CMOS counters occupy the logic IC and counter/d divider hierarchy: each successive output changes at a lower frequency than the preceding stage. Unlike 74HC logic, the CD4000 family supports a substantially wider supply-voltage range and is suited to industrial, control, instrumentation, and legacy-compatible systems operating from low-voltage CMOS through higher-voltage CMOS rails. The CD4024BE provides seven individually available count outputs, a common reset input, and a negative-edge clock transition. Its 3 V to 18 V operating range allows the same counter architecture to operate across multiple supply standards without requiring a level shifter. The 14-pin PDIP package supports conventional through-hole PCB assembly, prototyping, repair, and applications where a surface-mount package would be inconvenient. The ripple-carry architecture uses master-slave flip-flop stages, so each stage advances when the preceding stage changes. This implementation is appropriate when moderate clock rates, simple frequency division, and directly accessible binary outputs are more important than maximum operating frequency. Because carry propagation is sequential, cumulative propagation delay must be considered when the clock period is short or when all outputs must settle within a tightly defined interval. Typical uses include binary event counters, divide-by-two through divide-by-128 clock generation, industrial sequence and batch counters, timer reference stages, digital test equipment, and embedded control systems that need a simple count encoded across individual output pins. The CD4024BE is also useful when maintaining an existing CD4000-series design requires a standard PDIP counter with a wide supply range. For reliable implementation, keep clock rise and fall times within the limits stated by the manufacturer, observe the reset pulse requirements, and allow adequate settling time after the final ripple stage transitions. Decoupling should follow the manufacturer recommendations, while unused outputs should remain properly terminated according to the system’s CMOS conventions. The wide operating range does not eliminate the need to check propagation delay against the intended maximum clock frequency. This product page consolidates the manufacturer’s functional description, pin and package information, operating limits, genuine drop-in alternatives, and application-specific engineering guidance. It also provides parameter-by-parameter comparisons and practical circuit-design notes for engineers evaluating the CD4024BE against other 7-stage binary counters.
CD4024BEX - 7-Stage 24MHz CMOS Counter | Texas Instruments
Texas Instruments CD4024BEX is a 7-stage CMOS ripple-carry binary counter with a 24 MHz maximum count rate, falling-edge clock triggering, and a 3 V to 18 V operating supply range in a PDIP-14 through-hole package. It provides four parallel binary outputs and one independently controlled parallel output for a seven-bit counting application. The wide CMOS supply range allows operation from standard 5 V and 10 V systems, while the through-hole package supports conventional leaded assembly and socket-based prototyping. A binary counter is a sequential digital-logic circuit that records successive clock pulses as binary values. A ripple-carry counter implements this function by connecting multiple toggle stages, with each stage advancing when the preceding stage changes. The CD4000 CMOS family belongs to the broader hierarchy of counter ICs, digital logic ICs, integrated circuits, and semiconductors. Its asynchronous ripple architecture is useful when simple event counting, frequency division, timing, or programmable sequencing is required. The CD4024BEX combines a 7-stage count capacity with a stated maximum operating frequency of 24 MHz. Its four parallel binary outputs provide the lower four count bits, while the parallel output can represent the terminal count state. Falling-edge clock triggering defines the active transition for advancing the count. Operation across 3 V to 18 V gives designers flexibility across multiple supply domains, provided that input levels and timing requirements are evaluated for the selected supply voltage. The ripple-carry implementation uses cascaded counter stages, so propagation delay accumulates through the chain. This is more important than raw clock frequency when the circuit must produce a clean decoded event or the carry output must be timed precisely. The counter should be clocked only while reset is inactive, and unused inputs must be held at defined logic levels. CMOS devices require controlled input transitions to prevent transient current and output instability. Typical uses include digital timers, event counters, industrial sequence controllers, laboratory pulse-counting equipment, frequency dividers, and digital clock subsystems. It can also serve as a programmable event-counting element when a downstream system derives timing or sequencing information from the binary and carry outputs. Its 24 MHz capability supports substantially faster event counting than conventional low-frequency mechanical or slow CMOS timer systems. For robust PCB implementation, place the clock and reset traces away from output and power-return paths, especially when the counter drives long traces or sensitive clock-distribution circuitry. Confirm the maximum clock frequency at the actual supply voltage, and account for accumulated propagation delay in cascaded decoding logic. The Request a Quote form on this page supports current price, stock, and lead-time requests for production planning. This page combines the CD4024BEX operating limits, package information, pin-compatible alternatives, comparison parameters, and practical counter-design guidance. These engineering-focused details help buyers assess the counter for timers, automation, digital clocks, and pulse-counting systems while preserving a consistent PDIP-14 board design.
CD4024BFX - 7-Bit Binary Counter, 14-CDIP | Harris Corporation
Harris Corporation CD4024BFX is a 7-bit CMOS ripple-carry binary counter IC with one counting element, negative-edge triggering, and a 14-pin ceramic dual in-line package. The device is identified as military-grade and through-hole mounted, positioning it for legacy systems that require a 14-terminal rectangular DIP counter. Its principal electrical characteristics include a 7-bit counting capacity, binary counter organization, and a 14-CDIP package. A binary counter is a sequential digital-logic component that advances through a defined sequence of states when it receives an active clock transition. The CD4024BFX belongs to the CD4000 CMOS logic family, whose hierarchy is binary counter → counter IC → logic IC → digital semiconductor. Unlike a free-running oscillator, it advances only in response to its clock input, allowing a system to divide an incoming frequency into a lower binary-coded rate. The CD4024BFX provides one 7-bit counting element, negative-edge triggering, and a ripple-carry architecture. These features make it suitable for frequency division, modulo operation, event counting, timing intervals, and digital state sequencing. Its 14-CDIP construction also supports insertion into legacy sockets and hand-wired or stitched PCB assemblies. The manufacturer datasheet should be consulted for detailed electrical limits, setup timing, reset behavior, and environmental ratings before production use. Because this is a ripple-carry counter, propagation delay accumulates through the internal stages. The longest delay occurs between the first clocked stage and the final carry output. This characteristic makes the device most appropriate where one carry output is needed and moderately cascaded timing is acceptable, rather than for applications demanding simultaneous high-speed outputs from multiple counter sections. Typical uses include binary frequency division in industrial control equipment, pulse counting in test and measurement systems, programmable timing chains in legacy computing equipment, and sequential address or state generation. The negative-edge clock trigger allows the counter to change state on the falling transition of the clock waveform, which can simplify edge-sensitive interfacing with surrounding CMOS logic. PCB integration requires the 14-CDIP footprint and attention to signal-integrity practices, including short clock and reset traces, adequate bypass capacitance, and protection from unused inputs. Designers should also account for the cumulative ripple delay when cascading multiple counters or deriving timing from the terminal carry output. This product record combines package identification, counter characteristics, drop-in replacement considerations, comparison data, and practical implementation guidance. It is intended to support engineering selection and sourcing decisions for legacy Harris CD4024BFX assemblies rather than substituting a modern surface-mount design without appropriate timing, environmental, and lifecycle review.
CD4024BHSR - 7-Bit Binary Ripple Counter 3-18V | Renesas
The Renesas Electronics CD4024BHSR is a 7-bit binary ripple-carry counter IC with a maximum count rate of 12 MHz, operating from a 3 V to 18 V supply over the full military temperature range of -55C to +125C, supplied in unpackaged die form. The device counts on the negative-going clock edge and provides an asynchronous MASTER RESET input. A binary ripple counter is a digital counter in which the output of each flip-flop stage clocks the next stage, rather than all stages clocking from a common source. Ripple counters sit within the broader hierarchy of sequential logic -> counters/dividers -> logic ICs. Because the carry ripples through seven stages, propagation delays accumulate, which limits the maximum count frequency but yields an extremely simple, low-power, low-pin-count frequency divider architecture. Key features of the CD4024BHSR include the 7-bit counting range (divide-by-2 through divide-by-128), unbuffered monolithic CMOS construction, negative-edge clock triggering, and an asynchronous active-high reset. The wide 3 V to 18 V supply range makes it compatible with legacy CMOS and military power rails, and the -55C to +125C rating supports harsh-environment designs such as avionics and defense systems. Technically, the unbuffered CMOS output structure gives the part reduced switching noise and the ability to operate with very low quiescent power, although unbuffered outputs exhibit higher output impedance than buffered 4000-series equivalents. Each of the seven Q outputs divides the input clock by successive powers of two, enabling cascaded frequency division from a single package. Typical applications include frequency division in clock trees, long-duration timers in industrial controllers, event counting in instrumentation, and ripple-divider chains in military and aerospace electronics where the die-format packaging supports custom hybrid or COB (chip-on-board) assembly. When designing with this part, remember that asynchronous ripple counters produce decode glitches on intermediate states; decode only when the count is settled or use a synchronous counter if glitch-free outputs are required. This page adds information gain beyond the datasheet by consolidating distributor stock data, drop-in same-family alternatives, comparison tables, and practical design notes for the CD4024BHSR in one place.
CD4024BM - 7-Bit CMOS Ripple-Carry Counter | Texas Instruments
Texas Instruments CD4024BM is a CMOS 7-stage ripple-carry binary counter and divider with one 7-bit counter element, negative-edge triggering, and a 14-pin SOIC package. Its key characteristics include CMOS construction, a 3 V to 18 V operating range, and operation up to 24 MHz. The device advances its binary count when a clock transition occurs on the falling edge of the clock input. Four parallel binary outputs expose the seven counter states, while the divide-by-2, divide-by-4, divide-by-8, and divide-by-16 outputs provide convenient frequency division from the master clock. The CD4024BM is a digital counter IC, placing it within the broader CMOS logic and 4000-series counter hierarchy. A ripple-carry binary counter is a sequential digital circuit that stores and increments a binary value on each active clock edge. Unlike a synchronous counter, a ripple-carry implementation allows each internal stage to toggle after the preceding stage, which can create accumulated propagation delay between the clock input and the final output. This architecture remains useful when predictable division ratios, inexpensive implementation, and compatibility with classic CMOS logic systems are more important than simultaneous output transitions. The CD4024BM combines seven counter bits with selectable decoded divide outputs. The direct Q outputs support binary counting from 0000000 through 1111111, while the dedicated divider taps provide modulo-2, modulo-4, modulo-8, and modulo-16 signals. Its negative-edge clocking must be considered when multiple counters are cascaded because ripple transitions can create short timing differences between stages. The 3 V to 18 V supply range allows operation in both traditional 5 V CMOS systems and lower-voltage mixed-signal equipment. A maximum operating frequency of 24 MHz supports moderate-speed digital timing, event counting, and clock division. Because this is a CMOS logic device, unused inputs should not float; they should be tied to a defined valid logic level to prevent unpredictable current flow and noise sensitivity. Typical applications include digital frequency division, programmable event counters, industrial timing systems, laboratory pulse generation, sequential control logic, and clock-domain qualification circuits. Because the outputs are ripple-based, the device is especially appropriate for slower counter and divider functions where the final stage does not need to change simultaneously with the first stage. PCB design should preserve short clock routes, provide an uninterrupted ground reference, and account for the propagation delay through all seven stages when cascaded counters are combined. The manufacturer product page and datasheet should be used to assign inputs and outputs according to the exact CD4024B-family pin description, confirm operating limits, and select appropriate decoupling. This page combines the core counter and package characteristics, replacement analysis, application guidance, and practical design notes to support faster engineering selection. It also distinguishes directly compatible CD4024-family parts from broader functional equivalents so engineers can focus first on pin-compatible replacement options.
CD4024BMT - 7-Bit Ripple Counter | Texas Instruments
The Texas Instruments CD4024BMT is a CMOS 7-stage ripple-carry binary counter and divider with one counter element, a negative-edge clock input, and a 14-pin SOIC package. It operates from 3 V to 18 V and supports counting rates up to 24 MHz, making it suitable for digital frequency division, sequencing, timing, and general-purpose counter applications. A binary counter is a sequential logic device that increments or decrements a binary value on each active clock transition. The CD4024 belongs to the CMOS logic family, where CMOS means complementary metal-oxide-semiconductor. Within the broader product hierarchy, it is a logic IC, then a counter and divider, and finally a digital semiconductor used to implement state, timing, and frequency functions in electronic systems. The seven-stage architecture provides seven binary output stages, allowing division ratios from 2 through 128 when only the required output is used. Its negative-edge clock response means counting advances on the high-to-low transition of the clock signal. Separate parallel-load and master-reset inputs allow the counter to be initialized and controlled by external sequencing logic. The broad 3 V to 18 V supply range permits operation across common low-voltage and higher-voltage CMOS systems. At a maximum clock frequency of 24 MHz, the CD4024BMT supports relatively fast counting compared with basic low-frequency timer-counter functions. The architecture is ripple-carry, so each internal stage advances after the preceding stage. This provides a simple implementation for modulo counters and frequency dividers, although accumulated propagation delay between stages must be considered in high-speed cascaded designs. Typical uses include digital clock dividers, programmable timing generators, pulse and frequency counters, industrial sequence control, instrumentation, and embedded control systems. The 14-pin SOIC package supports conventional surface-mount assembly and fits PCB layouts designed around standard narrow-body integrated circuits. Designers should account for ripple propagation delay when several counter stages influence timing-critical downstream logic. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be tied to a defined logic level. The negative-edge triggering behavior must also be reflected in the clock-driver and reset timing design. This page combines the manufacturer's functional description, package and operating information, drop-in replacement assessment, side-by-side parameter comparison, and practical PCB guidance to support faster component selection and implementation planning.
CD4026AF/3 - 4-Bit Decade Counter | Texas Instruments
Texas Instruments CD4026AF/3 is a 4-bit decade counter and divider in a 16-pin DIP package. It counts decimal input pulses, provides 10 decoded outputs for one-of-ten display decoding, and includes a carry output for cascaded counting stages. The CD4026AF/3 is associated with the CD4000 CMOS logic family and is listed for counter and divider applications. A decade counter is a sequential digital-logic component that advances through ten states for every ten input-clock cycles. Positioned within the hierarchy of counters, counters, dividers, CMOS logic ICs, and semiconductors, the CD4026AF/3 is intended for frequency division, event counting, and display sequencing. Its 10 decoded outputs allow one output to be active for each of the ten count states. The principal system features are the 16-pin DIP package, decade-counting function, 10 decoded outputs, and carry output. The DIP-16 package supports through-hole PCB assembly and conventional socket-based prototyping. Because the CD4026AF/3 is a static CMOS counter, its clock, reset, inhibit, carry, and decoded-output functions provide a compact way to implement decimal sequencing without assembling a counter from individual gates. The CD4026 family is used where a counter must divide an input frequency by ten or translate a count into a one-of-ten output pattern. The carry terminal allows additional counting stages to be cascaded when more than ten states are required. Designers should also account for propagation delay when the counter output must align with high-speed clocks, and should verify the operating voltage, timing limits, and output-drive requirements against the manufacturer datasheet before finalizing a design. Typical uses include digital frequency dividers, decade sequencing circuits, seven-segment display drivers, pulse counters, clock dividers, and industrial control panels. The ten decoded outputs are especially useful for driving a display decoder when a system requires decimal count information rather than a conventional four-bit binary bus. For a new PCB, place the CD4026AF/3 according to the manufacturer pinout and route all unused inputs to a defined logic level. Add supply decoupling close to the device, use a consistent reset strategy, and confirm that the clock source satisfies the device's maximum transition requirements. A socket can simplify prototype replacement, but production assemblies normally use the DIP device directly. This page combines the manufacturer and distributor product information with practical pin-assignment, cascading, display-decoding, and counter-design guidance. It also separates confirmed product attributes from parameters that require confirmation in the manufacturer datasheet, helping engineers move from component selection to PCB implementation with fewer unresolved design questions.
CD4026BE - CMOS Decade Counter with 7-Segment Outputs | TI
Texas Instruments CD4026BE is a CMOS decade counter and divider with decoded 7-segment display outputs, a 5-bit counter, and a 16-lead plastic dual-in-line package. Its principal operating characteristics include a 3 V to 18 V supply range, operation up to 16 MHz, and fully static counting from DC to 6 MHz typical at Vpp = 10 V. The integrated decoder converts the internal Johnson-counter code into segment outputs for one numerical display stage, reducing the logic required in simple digital display systems. A CMOS decade counter is a digital logic device that counts clock pulses through ten states and divides a clock frequency by ten. The CD4026B belongs to the broader CMOS counter, divider, display-driver, and logic-IC hierarchy. Its decoded 7-segment outputs are designed for one display digit, making it useful for instrument panels, counters, timers, clock displays, and low-power numerical indicators. Texas Instruments identifies the device as particularly advantageous where low power dissipation and a low package count are important. The CD4026BE combines a 5-stage Johnson decade counter with an output decoder. Common control inputs include CLOCK, RESET, and INHIBIT, while decoded segment outputs drive the display elements. A display-enable output provides control over the decoded outputs. This integration allows a designer to replace a separate counter, decoder, and display-control interface with one dedicated IC, reducing component count and simplifying PCB layout. The device operates across a wide 3 V to 18 V supply range, allowing use in both low-voltage and higher-voltage CMOS systems. Its static counter operation supports DC through 6 MHz typical at Vpp = 10 V, making it appropriate for low-frequency timing and counting as well as higher-speed pulse-counting functions. The CMOS implementation supports low-power logic operation, although actual power consumption depends on supply voltage, clock activity, and the display load connected to the segment outputs. Typical applications include digital frequency meters, event counters, decade dividers, appliance timers, industrial panel displays, laboratory counters, and sequential display indicators. The decoded outputs are appropriate for common-cathode or common-anode seven-segment arrangements when the output polarity and segment interface are handled correctly. The display-enable function is particularly useful for blanking a display during reset, test, or controlled operating intervals. Designers should verify the segment polarity, clock-edge behavior, reset behavior, and inhibit function against the manufacturer's pin-description table before connecting a display. The input must not exceed the device's specified 18 V maximum supply voltage, and unused inputs should be held at a defined logic level rather than left floating. Decoupling capacitors should be placed close to the supply pins, while display-routing traces should be kept away from sensitive clock and reset nodes. This page consolidates the device's operating characteristics, package details, drop-in alternatives, application guidance, and practical implementation notes. It supports faster component selection while keeping the key design checks centered on supply limits, counter timing, display polarity, and exact 16-pin footprint compatibility.
CD4026BF - 5-Bit Decade Counter | Harris Corporation | Displays
The Harris Corporation CD4026BF is a CMOS decade counter and divider with a 5-bit output, 7-segment display decoder, positive-edge clocking, and a 16-CDIP package. According to the verified distributor data, it operates from 3 V to 18 V and supports operation up to 16 MHz. Its integrated decoder converts the counter's internal Johnson-code output into drive signals for one numerical seven-segment display, reducing the component count required in compact display systems. The CD4026BF is one member of the CD4000 CMOS logic family and is categorized as a counter, divider, and display-interface integrated circuit. A CMOS decade counter is a synchronous digital counter that advances through ten states for each complete decade of input pulses. The CD4026B combines a 5-stage Johnson counter with a seven-segment decoder, while the CD4033B provides a similar counter structure with binary rather than decoded display outputs. Within the broader hierarchy, the CD4026BF is a CMOS logic IC, a counter and divider, and a display-decoding integrated circuit. This integration is especially useful where low power dissipation, compactness, and direct seven-segment drive capability are important. The verified product data identifies a single counter element, 5-bit output organization, positive-edge triggering, and a 16-CDIP package. Its stated 3 V to 18 V supply range permits operation from conventional 5 V and 9 V logic systems as well as 15 V industrial-class supply rails. The stated 16 MHz operating frequency provides substantial counting headroom for digital clocks, timers, counters, sequencing circuits, and instrumentation. A qualified power design must still preserve the supply limits and respect the timing requirements of the connected logic family. The CD4026BF includes clock, clock-inhibit, reset, carry-in, carry-out, decoded display, and supply connections. Its decoded outputs are intended for one seven-segment numerical display rather than arbitrary seven-segment patterns. Carry-in and carry-out support decimal chaining, allowing multiple counting stages to represent values beyond a single decade. The external clock can be inhibited when required, while reset provides a defined starting state. Exact pin functions and electrical limits should be confirmed against the manufacturer datasheet before layout or production release. Typical uses include digital frequency meters, event counters, industrial panel displays, timer terminals, laboratory instruments, and compact decade-counting modules. In a seven-segment display application, the device can replace separate counter and decoder ICs, simplifying the board area and reducing interstage wiring. In cascaded decimal applications, carry-out can drive the next counter while carry-in determines the selected decade. Designers should account for display current, segment resistors, and the electrical loading of any additional logic connected to the decoded outputs. A critical design consideration is decoupling. Place the required supply-bypass capacitor close to the 16-CDIP power and ground pins, minimize the clock path between the oscillator or signal source and the clock input, and route return currents without sharing narrow paths with display-current returns. The CD4026BF is a digital counter rather than a power semiconductor, so a safe operating area specification is not applicable. Component marking, ceramic or hermetic grade, temperature grade, and sourcing conditions should be verified against the approved manufacturer documentation. This page consolidates the verified distributor specifications, package information, cross-reference evidence, practical application guidance, and honest replacement analysis for the CD4026BF. It also distinguishes electrically similar counter options from genuinely verified drop-in choices, helping engineers avoid assuming that same-family CMOS logic parts are interchangeable without checking pinout, supply voltage, display outputs, temperature grade, and package construction.
CD4026BF/3 - 4-Bit Decade Counter with 7-Segment Output | Harris
The Harris CD4026BF/3 is a 4-bit positive-edge decade counter with decoded 7-segment display output, supplied in a 16-CDIP package. It combines a decade counting stage with decoder outputs intended to drive common-cathode seven-segment displays. The part is presented as a logic counter IC, and its 16-CDIP construction supports through-hole assembly in designs that cannot use a surface-mount package. The suffix /3 identifies the particular Harris ordering variant, while CD4026BF denotes the related base device listed in the same 16-pin family. A decade counter is a sequential digital circuit that advances through ten states for each complete count cycle. The CD4026 family adds dedicated seven-segment decoding so a numerical state can be presented directly rather than requiring a separate binary-to-display decoder. In the power-management hierarchy of electronics, this device belongs to the CMOS logic family, within counters and dividers, and ultimately within integrated logic semiconductors. Its positive-edge behavior means the count advances in response to the designated clock transition. The principal engineering feature of CD4026BF/3 is integration: decade counting and seven-segment output decoding are combined in one 16-CDIP device. This can reduce the number of separate logic packages in a counter display module, simplify wiring between the counter and display, and preserve compatibility with legacy CD4000-series designs. The package also provides generous physical spacing between leads compared with most surface-mount logic packages, which can assist manual assembly and inspection in low-volume or maintenance-oriented equipment. The counter architecture supports decimal counting and frequency-division use, while its display outputs provide a direct interface to compatible seven-segment indicators. Designers should distinguish the decoded display outputs from ordinary binary outputs: the display outputs drive individual display segments rather than presenting a conventional parallel binary word. Any display interface must therefore use the segment polarity and drive arrangement defined by the connected indicator. Typical uses include decade-counter test equipment, industrial panel indicators, laboratory timers, educational electronics, and embedded displays that require a simple numerical count without a programmable microcontroller. A microcontroller-based product may choose a dedicated counter when the display interface is fixed, the system requires autonomous counting, or reducing firmware and logic-package count is valuable. For new designs that need arbitrary counting formats, bidirectional operation, or extensive configuration, a programmable counter or microcontroller may offer greater flexibility. The principal design consideration is package and logic compatibility. Because the device is offered in a 16-CDIP package, PCB land patterns and assembly processes must match the through-hole footprint. Verify clock, reset, inhibit, carry, segment-output, supply, and ground connections in the manufacturer datasheet before layout. Decoupling requirements, operating-voltage limits, output-drive capability, and timing values should also be taken from the device documentation rather than inferred from generic CD4000-series devices. This product page organizes the CD4026BF/3’s counter function, package information, sourcing route, comparison data, and practical design guidance. It also distinguishes exact drop-in candidates from merely similar counter devices, helping engineers select a replacement without changing the physical PCB footprint or changing display-interface requirements.
CD4026BPW - 5-Bit Decade Counter with 7-Segment Decoder | Texas Instruments
The Texas Instruments CD4026BPW is a CMOS decade counter and seven-segment display decoder integrated into a 16-lead thin shrink small-outline package (TSSOP). It provides five-bit counting with positive-edge clock operation and includes a dedicated seven-segment decoder output for common-anode display cathodes. The device is designed for low-power display and timing applications where a compact counter, display driver, and ripple output are useful in one package. According to the manufacturer datasheet information, fully static counter operation is possible from DC to 6 MHz typically at Vpp = 10 V, making the CD4026BPW suitable for digital clocks, timers, counters, and simple instrumentation displays. A decade counter is a sequential digital circuit that advances through ten states, from zero through nine, for every ten clock cycles. The CD4026BPW adds decoding logic that translates the internal count into segment signals intended for a seven-segment display. Its display-enable output provides a convenient way to inhibit segment outputs when the display is not needed. The same functional family also supports ripple blanking and lamp-test functions in appropriate device variants, useful for reducing visible transitions or checking display segments during manufacturing. The principal benefits of the CD4026BPW are integration, low static power consumption, and compact implementation. Integrating the counter and decoder reduces the number of external logic devices and PCB area required for a basic decimal display. The 16-TSSOP package also supports higher mounting density than a conventional through-hole DIP package. Because the device is a CMOS logic IC, its operating characteristics depend on the supply voltage and input levels, so the manufacturer’s recommended supply and input-voltage limits should be observed in the final circuit. Typical uses include kitchen timers, digital clock modules, pulse counters, industrial panel counters, teaching equipment, and small embedded display systems. The CD4026BPW is particularly appropriate when the display is a conventional seven-segment device and the required count range is decimal rather than binary. For designs requiring binary counting, a different counter family should be selected. Likewise, applications requiring a different output coding scheme or additional logic functions may benefit from a more specialized counter IC. When laying out a board, place the device close to the display connections and route clock, reset, and output signals with attention to switching noise and unused inputs. Confirm the display common-anode or common-cathode configuration before connecting segment and digit outputs. For design decisions, compare the CD4026BPW with the CD4026B family, the 16-pin TSSOP package options, and functionally similar decade-counter devices such as the CD4018 family. The latter has a different counting and preset structure, so it is not a universal substitute despite sharing a related CMOS counter role. This page combines manufacturer feature information, sourcing context, package details, and engineering guidance for selecting and integrating the CD4026BPW.
CD4028BF - CMOS BCD-to-Decimal Decoder | Texas Instruments
The Texas Instruments CD4028BF is a CMOS BCD-to-decimal or binary-to-octal decoder/driver housed in a 16-pin ceramic DIP (CDIP, J) package rated for the military -55C to +125C operating range. It accepts a 4-bit BCD input and asserts one of ten active-HIGH decoded outputs, with three additional binary-to-octal outputs for codes 10-15. Each input is buffered and the device operates across 3V to 18V supply with parametric ratings at 5V, 10V, and 15V. A BCD-to-decimal decoder is a combinational logic circuit in the CMOS 4000-series family that converts Binary Coded Decimal input codes (0000-1001) into one-of-ten mutually-exclusive active-high outputs. As a member of the decoder/driver category within the broader integrated circuit hierarchy (decoder/driver -> decoder -> logic IC -> semiconductor), it sits alongside address decoders, display drivers, and code converters, providing 1-of-10 fan-out with on-chip input buffering for direct drive of indicator tubes, Nixie displays, and memory-chip select lines. Key features of the CD4028BF include 4 buffered inputs with standard CMOS B-series noise immunity, 10 decoded outputs that are mutually exclusive (only one HIGH at a time), 3 additional outputs Y2/Y4/Y8 that decode the binary-to-octal function for codes 10-15, and quiescent current of approximately 0.5 uA at 5V VDD. The CDIP-16 ceramic package provides hermetic sealing for military and aerospace programs requiring extended reliability under thermal and mechanical stress. Per the TI CD4028B-MIL product page, the part meets all requirements of JEDEC Tentative Standard No. 13B for B-Series CMOS Devices. The CD4028BF is built on a 4000B-series CMOS process with P-channel and N-channel enhancement MOSFETs implementing the NAND/NOR decode matrix, followed by output buffers sized to source/sink approximately 1 mA at 5V VDD. The buffered inputs prevent input loading on the driving logic, allowing direct connection to standard TTL or CMOS sources even when VDD exceeds Vih(TTL). The decoded outputs are non-latching and follow the input code in real time, which simplifies memory-chip-select decoding where a static address must be continuously asserted. Typical applications include indicator-tube (Nixie) drivers for vintage instrumentation displays, memory-chip select decoding for systems requiring more than four chip enables, address decoding for I/O expansion, decimal readout for digital meters, and code conversion from BCD/binary to one-hot representations. The wide 3V to 18V supply range supports both 5V TTL and 15V CMOS system environments without level shifters. When designing with the CD4028BF, ensure VDD decoupling with a 0.1 uF ceramic capacitor placed close to pin 16 (VDD), tie unused inputs to VDD or GND to prevent shoot-through current, and verify that output sink/source current stays within the 1 mA limit when driving high-current loads such as Nixie cathodes - in those cases add a discrete transistor buffer stage. This page synthesizes distributor pricing, MIL-spec drop-in alternatives, pinout reference data, and PCB design notes not found in the bare datasheet, enabling engineers to source, qualify, and lay out the CD4028BF faster.
CD4029BCN - 4-Bit Binary/Decade Up/Down Counter | onsemi
The onsemi CD4029BCN is a 4-bit presettable CMOS counter that operates in binary or BCD decade mode, supports up and down counting, and triggers on the positive clock edge. It is packaged in a 16-lead plastic dual-in-line package, designated 16-PDIP or N16E, for through-hole PCB installation. A CMOS up/down counter is a digital logic IC that increments or decrements a multibit numerical state on each active clock transition. The CD4029 belongs to the broader CD4000 CMOS logic family, combining a four-stage counting core, programmable counting direction, selectable binary or decade operation, preset control, and reset control. This makes it part of the counter and divider hierarchy within general-purpose digital logic and system timing. The principal functional features include selectable binary or decade counting, programmable up or down direction, asynchronous reset, and individual preset inputs for the four counted bits. According to the Fairchild Semiconductor CD4029BCN datasheet, the counting mode is selected by the voltage applied to the binary/decade input. Individual Jan preset inputs allow a starting count to be loaded before normal counting resumes, which is useful for programmable timing and sequencing systems. The CD4029BCN is built around a four-stage CMOS counter with carry-in and carry-out control for extending counting or arithmetic sequences. Its positive-edge triggering gives the circuit a defined response to the rising clock transition, while the direction input selects whether the four-bit output moves toward higher or lower values. The device is intended for conventional CMOS supply operation; exact voltage limits, operating temperature range, and propagation-delay limits should be taken from the manufacturer datasheet before final circuit design. Typical applications include binary frequency division, decade stepper and sequencing circuits, programmable counters, digital timing modules, industrial control logic, and test equipment. It can also serve as a compact bidirectional state machine when a system needs a repeatable count sequence initiated from a preset value. Because the counter supports both binary and decade modes, one package can implement different numerical conventions without changing the physical footprint. The most important PCB consideration is correct orientation and unambiguous handling of the control inputs. Use the manufacturer pin-description table when routing the clock, carry, preset, reset, mode, and direction signals. Place bypass capacitors close to the supply pins and keep clock traces away from noisy switching nodes. In designs using individual presets, account for switch bounce or ensure that preset inputs remain stable while preset enable is active. This page combines function, package, and lifecycle details with a focused replacement assessment and practical design guidance. It also identifies where alternative manufacturer documentation should be consulted for electrical limits and timing details that are not stated in the distributor summaries.