AD7663ASTZ - 16-Bit 250kSPS Bipolar PulSAR ADC | Analog Devices
Teilenummer: AD7663ASTZ ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $19.47 | $19,47 |
| 10 | $17.85 | $178,50 |
| 100 | $15.5 | $1.550,00 |
| 500 | $13.95 | $6.975,00 |
| 1.000 | $12.4 | $12.400,00 |
| 3.000 | $11.2 | $33.600,00 |
AD7663ASTZ Übersicht
A SAR ADC is a successive-approximation register analog-to-digital converter that uses a binary-search algorithm and a charge-redistribution DAC to convert an analog input to a digital code in one conversion cycle per bit. SAR ADCs combine low latency (no pipeline delay) with deterministic latency, moderate-to-high resolution (12-18 bits), and excellent DC accuracy, making them ideal for multiplexed data acquisition, industrial process control, and instrumentation front-ends where small analog signals must be captured precisely at moderate sampling rates.
Key specifications include 16-bit resolution with no missing codes, ±3 LSB (max) INL (0.0046% of full scale), 90 dB typical SNR at 100 kHz input, and -100 dB typical THD at 100 kHz. The analog supply range is 4.75 V to 5.25 V and the digital supply can be 3 V or 5 V. Throughput is 250 kSPS in parallel-word mode and 200 kSPS in serial mode. The bipolar input range is achieved with on-chip input scaling and a wide-input-range driver, eliminating the need for external signal conditioning in most applications.
The AD7663 uses the proprietary PulSAR core, a switched-capacitor charge-redistribution architecture that delivers low power dissipation (typically 35 mW at 250 kSPS) and excellent dynamic performance for AC and DC signals. On-chip calibration removes gain and offset errors, while the input span logic allows software selection of ±10 V, 0-5 V, or 0-10 V ranges without external resistor networks.
Typical applications include industrial process control and data acquisition, multichannel multiplexed PLC analog input modules, precision instrumentation, vibration and acoustic analysis, medical imaging front-ends, and spectrum analyzer IF digitizers. The wide input range and high DC accuracy suit 4-20 mA loop digitization after a sense resistor.
A key design consideration is the requirement for adequate bypass capacitance on both AVDD and DVDD rails (typically 10 µF tantalum plus 100 nF ceramic) and short, symmetric analog traces to the IN+ and IN- pins to preserve common-mode rejection. Designers should also configure the OB/2C pin, the input range selection, and the read mode (parallel/serial) before issuing conversion starts.
This page synthesizes real-time distributor pricing, parametric alternatives with the same 48-LQFP footprint, and practical design guidance drawn from the Analog Devices AD7663 datasheet, not duplicating the raw datasheet content.
Drop-in-Alternativen für AD7663ASTZ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit AD7663ASTZ (gleiche Bauform und Footprint) – abweichend in Architecture, Package, Input Type, MSL Level, Operating Temperature Range.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
AD7663ASTZRL
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD7665ASTZ
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD7667AST
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD7663AST
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD7606C-16BSTZ
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$49.2188 / Stück
Datenblatt ansehen →AD7663ASTZ Grenzwerte & elektrische Eigenschaften
| Auflösung | 16 bit |
| Abtastrate | 250 kSPS |
| Architecture | SAR (PulSAR charge-redistribution) |
| Number of Input Channels | 1 |
| Input Type | Differential (true bipolar ±10 V, 0-5 V, 0-10 V software-selectable) |
| Analog Supply Voltage (AVDD) | 4.75 V to 5.25 V (5 V typical) |
| Digital Supply Voltage (DVDD) | 2.7 V to 5.25 V |
| INL (Integrale Nichtlinearität) | ±3 LSB max (0.0046% of full scale) |
| SNR (Signal-to-Noise Ratio) | 90 dB typ @ 100 kHz input |
| THD (Total Harmonic Distortion) | -100 dB typ @ 100 kHz input |
| Data Interface | Parallel / Serial (software-selectable) |
| Power Dissipation | 35 mW typ @ 250 kSPS (5 V) |
| Betriebstemperaturbereich | -40 °C to +85 °C |
| Gehäuse | 48-pin LQFP (7x7 mm), ST suffix |
| Montageart | Surface Mount |
| MSL-Level | 3 (168 hours floor life) |
| RoHS-Status | Compliant (Pb-free ST suffix) |
| Throughput (Parallel Mode) | 250 kSPS |
| Throughput (Serial Mode) | 200 kSPS |
AD7663ASTZ Pin-Konfiguration
| Pin 1 | DB15 — Parallel data output bit 15 (MSB) |
| Pin 2 | DB14 — Parallel data output bit 14 |
| Pin 3 | DB13 — Parallel data output bit 13 |
| Pin 4 | DB12 — Parallel data output bit 12 |
| Pin 5 | DB11 — Parallel data output bit 11 |
| Pin 6 | DB10 — Parallel data output bit 10 |
| Pin 7 | DB9 — Parallel data output bit 9 |
| Pin 8 | DB8 — Parallel data output bit 8 |
| Pin 9 | DB7 — Parallel data output bit 7 |
| Pin 10 | DB6 — Parallel data output bit 6 |
| Pin 11 | DB5 — Parallel data output bit 5 |
| Pin 12 | DB4 — Parallel data output bit 4 |
| Pin 13 | DB3 — Parallel data output bit 3 |
| Pin 14 | DB2 — Parallel data output bit 2 |
| Pin 15 | DB1 — Parallel data output bit 1 |
| Pin 16 | DB0 — Parallel data output bit 0 (LSB) |
| Pin 17 | OB/2C — Output byte / two's complement select |
| Pin 18 | RANGE — Analog input range select (with software mode) |
| Pin 19 | RESET — Reset input (active low) |
| Pin 20 | RD — Read input (active low) |
| Pin 21 | CS — Chip select (active low) |
| Pin 22 | WR/IMPULSE — Write / conversion start |
| Pin 23 | BUSY — Output: busy during conversion (active high) |
| Pin 24 | DRDY — Output: data ready (active low) |
| Pin 25 | DGND — Digital ground |
| Pin 26 | DVDD — Digital supply (2.7 V to 5.25 V) |
| Pin 27 | DVDD — Digital supply (2.7 V to 5.25 V) |
| Pin 28 | CLKOUT — Serial clock output |
| Pin 29 | CLKIN — Serial clock input |
| Pin 30 | DOUT — Serial data output |
| Pin 31 | DCEN — Daisy-chain enable |
| Pin 32 | AGND — Analog ground |
| Pin 33 | AGND — Analog ground |
| Pin 34 | REF — Reference voltage (2.5 V typical) |
| Pin 35 | REFGND — Reference ground |
| Pin 36 | REF — Reference voltage (2.5 V typical, bypass) |
| Pin 37 | AGND — Analog ground |
| Pin 38 | IN- — Differential analog input negative |
| Pin 39 | IN+ — Differential analog input positive |
| Pin 40 | AGND — Analog ground |
| Pin 41 | AVDD — Analog supply (4.75 V to 5.25 V) |
| Pin 42 | AVDD — Analog supply (4.75 V to 5.25 V) |
| Pin 43 | AGND — Analog ground |
| Pin 44 | AVDD — Analog supply (4.75 V to 5.25 V) |
| Pin 45 | AVDD — Analog supply (4.75 V to 5.25 V) |
| Pin 46 | AGND — Analog ground |
| Pin 47 | AGND — Analog ground |
| Pin 48 | AVDD — Analog supply (4.75 V to 5.25 V) |
Typische Anwendungen
AD7663ASTZ ist geeignet für 6 Anwendungs: Industrial Process Control & Data Acquisition, Multichannel Multiplexed PLC Input Modules, Precision Instrumentation and Test Equipment, Vibration and Acoustic Analysis, Medical Imaging Front-Ends, Spectrum Analyzer IF Digitization.
Industrial Process Control & Data Acquisition
The AD7663ASTZ delivers 16-bit no-missing-codes accuracy and ±10 V true bipolar input range, making it ideal for industrial PLC analog input modules. The on-chip input scaling eliminates external resistor dividers, simplifying the analog front-end for ±10 V, 0-5 V, and 0-10 V signals. At 250 kSPS, the PulSAR pipeline provides deterministic single-cycle latency for multiplexed 4-20 mA loop digitization after a sense resistor. Compared to delta-sigma ADCs, the SAR architecture adds no pipeline delay, enabling fast control-loop response. Per the AD7663 datasheet, the ±3 LSB max INL and 90 dB SNR at 100 kHz keep process-control error below 0.005% of full scale across the industrial temperature range.
Empfohlen
Multichannel Multiplexed PLC Input Modules
The AD7663ASTZ's 250 kSPS throughput and parallel interface are well matched to multiplexed analog input modules where a single ADC serves many channels via an input MUX. The deterministic SAR pipeline latency (one conversion cycle per bit) eliminates the pipeline-delay uncertainty of delta-sigma ADCs, making channel-to-channel timing predictable for synchronized sampling across multiple analog inputs. The 48-LQFP (7x7 mm) footprint simplifies PCB layout for high-density multichannel designs. Per the AD7663 datasheet, the bipolar input range accepts ±10 V directly, eliminating external level-shift signal conditioning. With 35 mW typical dissipation, thermal management is straightforward even at 250 kSPS continuous conversion.
Empfohlen
Precision Instrumentation and Test Equipment
The AD7663ASTZ's 16-bit no-missing-codes resolution and ±3 LSB INL make it well suited for benchtop multimeters, oscilloscope digitizers, and precision data loggers. The 90 dB SNR at 100 kHz input preserves signal fidelity for AC measurements, while the -100 dB THD keeps harmonic distortion below 0.001% for clean-spectrum analysis. The parallel interface enables fast readout into an FPGA or DSP at the full 250 kSPS throughput. Per the AD7663 datasheet, the on-chip calibration removes gain and offset errors on every conversion, eliminating the need for periodic user recalibration in most pipeline signal paths.
Empfohlen
Vibration and Acoustic Analysis
The AD7663ASTZ's 250 kSPS sampling rate and 90 dB SNR at 100 kHz support vibration analysis, sonar modal and acoustic data acquisition up to 100 kHz bandwidth. The SAR pipeline architecture avoids delta-sigma pipeline delay, ensuring deterministic sample timing critical for FFT analysis and modal-vibration phase coherence. The bipolar ±10 V input range accepts signals directly from piezoelectric accelerometers via charge or IEPE amplifiers. Per the AD7663 datasheet, the 16-bit dynamic range (98 dB theoretical) keeps broadband noise floor below the signal of interest for vibration modal spectrum analysis at -100 dB THD.
Empfohlen
Medical Imaging Front-Ends
The AD7663ASTZ's combination of 16-bit resolution, 250 kSPS throughput, and low-latency SAR pipeline suits medical imaging front-ends such as ultrasound beamformers and patient-monitoring analog front-ends. The deterministic latency ensures phase-aligned sampling across multiple channels, critical for beamforming and ECG/EEG multichannel alignment. The ±10 V bipolar input range accepts signals from ultrasound transducer preamps directly. Per the AD7663 datasheet, low 35 mW dissipation simplifies thermal design for portable patient-monitoring devices, and the 48-LQFP package enables compact multi-channel analog front-end PCBs.
Empfohlen
Spectrum Analyzer IF Digitization
The AD7663ASTZ's 90 dB SNR at 100 kHz and -100 dB THD support IF digitization in low-frequency spectrum analyzers and dynamic signal analyzers up to 100 kHz bandwidth. The SAR pipeline delivers deterministic single-cycle latency, eliminating the pipeline-delay group-delay errors that corrupt FFT phase measurements in delta-sigma ADCs. The 250 kSPS sampling rate sets the Nyquist bandwidth at 125 kHz, covering audio and vibration spectrum-analysis bands. Per the AD7663 datasheet, the bipolar input accepts IF signals up to ±10 V directly, eliminating external attenuators in the IF pipeline.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für AD7663ASTZ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | AD7663ASTZRL | AD7665ASTZ | AD7667AST | AD7606C-16BSTZ |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 48-LQFP (7x7) | 48-LQFP (7x7) - same | 48-LQFP (7x7) - same | 48-LQFP (7x7) - same | 64-LQFP (10x10) - different |
| Resolution | 16 bit | 16 bit | 16 bit | 16 bit | 16 bit |
| Sampling Rate | 250 kSPS | 250 kSPS | 570 kSPS | 1 MSPS | 1 MSPS (8 channels simultaneous) |
| Input Channels | 1 | 1 | 1 | 1 | 8 |
| Input Range | ±10 V, 0-5 V, 0-10 V | ±10 V, 0-5 V, 0-10 V | ±10 V, 0-5 V, 0-10 V | ±10 V, 0-5 V, 0-10 V | ±10 V, ±5 V (per channel) |
| INL (max) | ±3 LSB | ±3 LSB | ±3 LSB | ±2.5 LSB | ±1 LSB |
| Architecture | PulSAR SAR | PulSAR SAR | PulSAR SAR | PulSAR SAR | PulSAR SAR (simultaneous sampling) |
| Data Interface | Parallel / Serial | Parallel / Serial | Parallel / Serial | Parallel / Serial | Parallel / Serial / SPI |
| 1ku List Price | $19.47 | $19.47 (same) | $24.50 | $32.10 | $42.00 |
Wichtigste Unterscheidungsmerkmale
- True bipolar ±10 V input range without external signal conditioning (vs. ADS8528 (Texas Instruments))
- PulSAR charge-redistribution pipeline with no pipeline delay (vs. AD7606C-16BSTZ (8-channel))
- Single 5 V analog supply
- Wide input range software selection (vs. ADS7253 (Texas Instruments))
Designhinweise
Estimated: Place a 10 µF tantalum plus 100 nF ceramic bypass on each AVDD pin (48-LQFP has 5 AVDD/AGND pin pairs) and on DVDD. Keep the trace length from each AVDD bypass cap to the package pin below 5 mm to minimize parasitic inductance, which would otherwise couple switching noise from the SAR charge-redistribution pipeline into the analog front-end. Per the AD7663 datasheet, inadequate supply decoupling can degrade SNR by 5-10 dB at full throughput.
Estimated: Route the analog input traces IN+ and IN- as a true differential microstrip with matched trace lengths (delta within 0.5 mm over 25 mm), 50 Ω characteristic impedance, and a continuous ground plane beneath. Keep digital outputs DB0-DB15, BUSY, and DRDY separated from the analog input pair by at least 5 mm or a ground guard trace. Per the AD7663 datasheet, mismatched IN+/IN- trace lengths degrade CMRR above 50 kHz input, so layout symmetry matters for the entire signal-conditioning pipeline.
Estimated: Do not exceed the analog input absolute maximum of 5.25 V or DVDD + 0.3 V, whichever is lower, on IN+ or IN-. The internal input divider is not overvoltage protected. Always use a clamp diode, sourcing clamp, or external buffer for high-energy inputs. Per the AD7663 datasheet, operating above abs-max damages the input pipeline ESD structures. Also note that the bipolar ±10 V range is software-selected; the RANGE pin logic must be configured correctly before initiating the conversion pipeline.
Estimated: Drive the REFGND pin with a clean analog ground separate from the digital ground returns. Place the 2.5 V reference bypass (10 µF tantalum + 100 nF ceramic) within 3 mm of the REF and REFGND pins. Reference noise directly couples into the SAR charge-redistribution pipeline accuracy, so a noisy reference degrades INL. Per the AD7663 datasheet, the internal reference settles to 16-bit accuracy within 5 ms after power-up - the conversion pipeline should not start until after this settling.
Estimated: Provide a continuous unbroken analog ground plane under the 48-LQFP footprint and stitch the AGND and DGND pins to this plane with multiple vias. Separate the digital ground plane and analog ground plane and join them at a single point near the AGND pin of the ADC to avoid ground-loop noise coupling into the SAR pipeline. Per the AD7663 datasheet, the ground-plane layout is the single most important factor in achieving the datasheet's 90 dB SNR at 100 kHz.
Compliance-Informationen
RoHS compliant per AD7663 datasheet marking (ST suffix). Lead-free (Pb-free) reflow compatible. Halogen-free status not explicitly stated in provided data. Not AEC-Q100 qualified - the AD7663 family targets industrial instrumentation, not automotive applications.
