ADC121S051CISDX - 12-Bit 200-500ksps Differential Input ADC | Texas Instruments
Teilenummer: ADC121S051CISDX ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $2.85 | $2,85 |
| 10 | $2.56 | $25,60 |
| 100 | $2.18 | $218,00 |
| 500 | $1.92 | $960,00 |
| 1.000 | $1.74 | $1.740,00 |
| 3.000 | $1.55 | $4.650,00 |
ADC121S051CISDX Übersicht
A SAR (successive-approximation register) ADC is a class of Nyquist-rate analog-to-digital converter that resolves N bits per conversion in N clock cycles by comparing the input against a binary-weighted internal DAC. SAR ADCs are valued for their deterministic latency, single-shot accuracy, low power consumption, and ease of use because no pipeline delay exists between sampling and conversion completion. They sit in the hierarchy: SAR ADC -> ADC -> data converter -> mixed-signal IC -> semiconductor. The ADC121S051 family is one of TI's pin-compatible "ADC121Sxx1" platforms that share footprint across 8/10/12-bit resolutions and three sample-rate bands (50-200 ksps, 200-500 ksps, 500 ksps-1 Msps).
Key differentiating specifications include true differential input architecture (rejecting common-mode noise from ground loops and motor drive stages), an external SCLK-driven serial data clock eliminating the need for an internal oscillator, a hardware CS (chip-select) frame for multi-channel bus sharing, and straight-binary serial output format compatible with SPI, QSPI, MICROWIRE, and many DSP serial ports. A single conversion is initiated on the falling edge of CS and clocked out MSB-first on subsequent SCLK rising edges.
Architecturally, the device uses a charge-redistribution DAC array, an internal bandgap-derived reference path, and a track-and-hold front end sized for full-scale inputs up to VA. Its low duty-cycle operation makes it attractive for battery and portable applications. Performance is fully specified across the entire 200-500 ksps range rather than at a single point, simplifying design-in for variable-rate DSP pipelines.
Typical applications include portable instrumentation, hand-held battery-powered meters, automotive sensor monitoring (non-safety), industrial process control loopback monitoring, audio front-end level detection, and consumer white-goods user-interface subsystems. The wide supply tolerance allows direct connection to common 3.3V and 5V digital rails.
When designing with this device, ensure SCLK remains idle-low or idle-high consistent with the chosen SPI mode, and provide adequate input settling time by buffering high-impedance signal sources. Decouple VA with a 0.1 uF capacitor placed within 5 mm of the supply pin to suppress digital switching transients that couple into the analog input.
This page synthesizes real-time distributor pricing, drop-in pin-compatible alternatives, and practical design notes that go beyond the manufacturer datasheet, supporting faster BOM risk evaluation by two-stage sourcing.
Drop-in-Alternativen für ADC121S051CISDX – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ADC121S051CISDX (gleiche Bauform und Footprint) – abweichend in Package, Resolution, Architecture, RoHS Status, Input Voltage Range.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
ADC121S051CISD/NOPB
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADC121S051CIMF/NOPB
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADC121S021CISDX
✅ Drop-In✓ Auf Lager
$1.85 / Stück
Datenblatt ansehen →ADC101S051CISDX
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$1.28 / Stück
Datenblatt ansehen →ADC121S101CISDX
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADC081S051CISDX/NOPB
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$1.62 / Stück
Datenblatt ansehen →ADC121S051CISDX Grenzwerte & elektrische Eigenschaften
| Manufacturer | Texas Instruments |
| Part Family | ADC121S051 (pin-compatible ADC121Sxx1 series) |
| Auflösung | 12 bits |
| Number of Channels | 1 (single-ended or differential input) |
| Sample Rate Range | 200 ksps to 500 ksps |
| Architecture | SAR (Successive Approximation Register) |
| Input Type | Differential (pseudo-differential capable) |
| Supply Voltage (VA) | +2.7 V to +5.25 V (single supply) |
| Power Consumption at 3.6 V | 1.7 mW (typical) |
| Power Consumption at 5.25 V | 8.7 mW (typical) |
| Digital Interface | SPI, QSPI, MICROWIRE, DSP-compatible serial |
| Output Format | Straight binary (MSB-first) |
| Betriebstemperaturbereich | -40 C to +85 C (industrial) |
| Gehäuse | 6-pin LLP/WSON (2.2 x 2.5 mm) with exposed pad |
| Montageart | Surface Mount |
| MSL-Level | 1 (per data) |
| RoHS-Status | Compliant (lead-free) |
| Eingangsspannungsbereich | 0 V to VA (full-scale) |
| Screening Level | Industrial |
ADC121S051CISDX Pin-Konfiguration
| Pin 1 | VA — Analog power supply input (+2.7V to +5.25V) |
| Pin 2 | GND — Ground reference |
| Pin 3 | VIN+ — Positive differential analog input |
| Pin 4 | VIN- — Negative differential analog input (common-mode reference) |
| Pin 5 | SCLK — Serial clock input (SPI/QSPI/MICROWIRE) |
| Pin 6 | DOUT — Serial data output (MSB-first, straight binary) |
Typische Anwendungen
ADC121S051CISDX ist geeignet für 7 Anwendungs: Portable Battery-Powered Instrumentation, Industrial Sensor Monitoring, Audio Front-End Level Detection, Automotive Sensor Readback (non-safety), White Goods User-Interface Subsystems, Process Control Loopback Monitoring, Hand-Held Digital Multimeter Front End.
Portable Battery-Powered Instrumentation
The ADC121S051CISDX is an excellent fit for portable battery-powered instrumentation because its 1.7 mW typical power consumption at 3.6V and automatic power-down between conversions extends Li-ion battery life significantly. The wide +2.7V to +5.25V single-supply range allows direct connection to a single Li-ion cell (3.0-4.2V) without boost or buck regulators. The 12-bit resolution at 200-500 ksps provides more than enough accuracy for temperature, pressure, and battery-monitoring sensor front ends, while the 6-pin LLP/WSON (2.2 x 2.5 mm) footprint preserves board area in compact handheld meters.
Empfohlen
Industrial Sensor Monitoring
For industrial sensor monitoring applications, the ADC121S051CISDX's true differential input (VIN+ / VIN-) rejects common-mode noise from ground loops, motor drives, and long sensor leads typical of factory floor installations. The wide +2.7V to +5.25V supply tolerates 24V industrial bus rails stepped down through common DC-DC converters, while the -40C to +85C industrial operating range covers most factory environments. SPI/QSPI/MICROWIRE compatibility allows direct connection to most industrial host MCUs without glue logic, and 12-bit accuracy is sufficient for 4-20 mA loopback monitoring, temperature sensing, and pressure transducer readback.
Empfohlen
Audio Front-End Level Detection
The ADC121S051CISDX can be used as an audio front-end level detector in consumer audio products where a microcontroller needs to read the rectified audio signal level for VU-meter, automatic gain control, or compressor sidechain processing. With 200-500 ksps, the device easily oversamples audio bandwidth signals (20 Hz - 20 kHz), and the 12-bit resolution provides 72 dB dynamic range sufficient for level detection rather than full audio fidelity. The differential input rejects common-mode hum from ground loops between the audio source and the digital host.
Empfohlen
Automotive Sensor Readback (non-safety)
In non-safety automotive applications such as cabin climate sensors, HVAC controls, seat position feedback, and interior lighting controllers, the ADC121S051CISDX provides cost-effective 12-bit conversion at 200-500 ksps from the vehicle's 5V or 3.3V rail. Although this part is industrial-grade (-40C to +85C), it fits comfortably under-hood sensor readbacks where the cabin and chassis temperatures stay within industrial range. For safety-critical powertrain or ADAS applications requiring AEC-Q100, designers should step to a qualified alternative.
Empfohlen
White Goods User-Interface Subsystems
The ADC121S051CISDX fits well in white-goods user-interface subsystems such as washing-machine rotary-encoder position sensing, refrigerator temperature readback, and dishwasher button-matrix analog multiplexing. Its low 1.7 mW power consumption at 3.6V meets ENERGY STAR standby requirements, while the small LLP/WSON (2.2 x 2.5 mm) footprint suits high-volume consumer appliance PCBs. SPI compatibility with low-cost appliance MCUs eliminates the need for external glue logic, and 12-bit resolution is sufficient for thermistor temperature sensing and rotary control position feedback.
Empfohlen
Process Control Loopback Monitoring
In process-control loopback monitoring applications where a microcontroller reads back the output of a 4-20 mA current loop or 0-10V analog output stage, the ADC121S051CISDX provides accurate 12-bit conversion at 200-500 ksps with differential input that rejects common-mode noise. The wide +2.7V to +5.25V supply supports both 3.3V and 5V PLC analog backplanes, and the SPI interface allows direct connection to PLC CPUs. The automatic power-down between conversions reduces heat dissipation in dense PLC analog input modules.
Empfohlen
Hand-Held Digital Multimeter Front End
For hand-held digital multimeter (DMM) and clamp-meter front ends, the ADC121S051CISDX provides 12-bit voltage measurement conversion at 200-500 ksps with differential input that rejects common-mode noise from the shunt resistor in current-measurement mode. The wide +2.7V to +5.25V supply supports both 3.3V and 5V DMM architectures, and the low 1.7 mW power consumption extends 9V battery life significantly. The compact 6-pin LLP/WSON package suits the cramped interior of handheld meter enclosures, and SPI compatibility with low-cost DMM MCUs simplifies the firmware design.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ADC121S051CISDX – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ADC121S051CISD/NOPB | ADC121S051CIMF/NOPB | ADC121S021CISDX | ADC101S051CISDX | ADC121S101CISDX | ADC081S051CISDX/NOPB |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 6-WSON (2.2x2.5) | 6-WSON (2.2x2.5) - same | 6-WSON (2.2x2.5) - same | 6-WSON (2.2x2.5) - same | 6-WSON (2.2x2.5) - same | 6-WSON (2.2x2.5) - same | 6-WSON (2.2x2.5) - same |
| Resolution | 12 bits | 12 bits | 12 bits | 8 bits | 10 bits | 12 bits | 8 bits |
| Sample Rate Range | 200-500 ksps | 200-500 ksps | 200-500 ksps | 200-500 ksps | 200-500 ksps | 500 ksps to 1 Msps | 200-500 ksps |
| Supply Voltage | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V |
| Input Type | Differential | Differential | Differential | Differential | Differential | Differential | Differential |
| Digital Interface | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Wichtigste Unterscheidungsmerkmale
- Pin-compatible across 8/10/12-bit resolution and three speed bands within one footprint (vs. ADC121S021CISDX (8-bit) and ADC121S101CISDX (12-bit @ 1 Msps))
- True differential input rejects common-mode noise from ground loops and motor drives (vs. Single-ended ADCs in similar packages (e.g., pseudo-differential parts))
- Wide +2.7V to +5.25V single-supply operation removes alt-connectivity requirements (vs. Older 5V-only ADCs (e.g., AD574A) requiring +/-12V rails)
Designhinweise
Estimated: at 3.6V supply and continuous 500 ksps sampling, the ADC121S051CISDX dissipates approximately 2.4 mW per the TI datasheet's 1.7 mW typical figure, plus digital switching transients. Place a 0.1 uF ceramic decoupling capacitor within 5 mm of the VA pin (pin 1) and a 10 uF bulk capacitor on the supply rail to suppress digital switching noise coupling into the analog input. The exposed thermal pad must be soldered to a grounded copper pour to provide thermal mass and a low-impedance ground return.
Keep analog input traces (VIN+ / VIN-) short and symmetric, and route them away from the SCLK and DOUT digital traces to minimize digital switching noise coupling into the analog front end. Use a guard trace tied to GND between the analog and digital sections of the PCB. The exposed thermal pad (EP) on the bottom of the LLP/WSON package should be soldered to a ground copper pour to reduce ground-bounce and provide thermal relief. Place the 0.1 uF VA decoupling capacitor as close to pin 1 as physically possible.
Use a low-impedance source driver for VIN+ and VIN- - high source impedance degrades the ADC's AC performance because the internal track-and-hold requires finite settling time. Add an external input buffer op-amp with low output impedance (less than 50 ohm) if the source impedance exceeds 1 kohm. The differential input rejects common-mode noise, but only if the source maintains the common-mode voltage within the input common-mode range of 0 V to VA.
Do not exceed the absolute maximum analog supply voltage of 6.5V on the VA pin, or the device will be permanently damaged. Ensure SCLK remains idle in the correct logic state for your chosen SPI mode (CPOL/CPHA) before initiating a conversion - an SCLK glitch during the conversion cycle can corrupt the result. The exposed thermal pad must be soldered for proper electrical and thermal performance; an unsoldered pad can cause thermal stress and erratic ADC readings.
Compliance-Informationen
RoHS-compliant (lead-free) per Ti product page and distributor listings. Not AEC-Q100 qualified - for safety-critical automotive use, step to an AEC-Q100 qualified SAR ADC. Operating temperature range is -40C to +85C industrial grade.
