ADF5000BCPZ-RL7 - 18 GHz Divide-by-2 RF Prescaler | ADI
Teilenummer: ADF5000BCPZ-RL7 ✓ AktivADF5000BCPZ-RL7 Übersicht
An RF prescaler is a frequency-divider block that reduces a high-frequency carrier to a lower frequency that a PLL synthesizer can process. The ADF5000 belongs to the divide-by-2 prescaler category and is positioned within the broader RF frequency-synthesis hierarchy: RF prescaler, divide-by-2 prescaler, frequency divider, clock and timing IC, and semiconductor. Its fixed division ratio simplifies feedback-path design in PLL-based microwave and wireless transmitters.
Key features include a 4 GHz to 18 GHz operating range, a fixed divide-by-2 function, a 3.3 V supply requirement, and differential 100-ohm outputs. The high-frequency input capability is useful when a downstream synthesizer has a limited prescaler input range. The differential output arrangement can simplify impedance matching and reduce susceptibility to common-mode disturbances when the following device provides a differential RF input.
Technically, the ADF5000 divides the RF input by two while preserving the signal path needed by a PLL feedback divider. Analog Devices identifies the ADF5000 as low-noise and low-power, making it appropriate for communication equipment in which divider-added phase noise or excessive power consumption would degrade the overall frequency synthesizer. Its differential outputs are intended to interface directly with RF circuitry designed for balanced operation.
Typical applications include microwave PLL feedback dividers, wireless transceiver local-oscillator synthesis, microwave test equipment, radar and satellite communication chains, and instrumentation requiring frequency division near 18 GHz. The part is particularly relevant when the synthesizer input stage cannot accommodate the original RF frequency but can accept the half-frequency output.
PCB implementation requires careful treatment of the RF input and output paths. Keep the RF traces short, use controlled-impedance routing, and provide the supply decoupling and exposed-pad thermal path specified by the manufacturer. The differential output impedance is 100 ohms, so matching networks and transmission-line geometry should be calculated for the complete board stack-up rather than added by trial and error.
This product page consolidates the device function, operating limits, package constraints, application guidance, and qualification questions into an engineering-oriented reference. It also identifies the limited set of genuinely compatible catalog options, avoiding unrelated dividers that may use the same package family but provide a different division ratio or pin function.
Drop-in-Alternativen für ADF5000BCPZ-RL7 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ADF5000BCPZ-RL7 (gleiche Bauform und Footprint) – abweichend in Device Type, Output Impedance.
ADF5000BCPZ
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →ADF5000BCPZ-RL7 Technische Daten
| Device Type | Fixed divide-by-2 RF prescaler |
| Input Frequency Range | 4 GHz to 18 GHz |
| Maximum RF Input Frequency | 18 GHz |
| Division Ratio | 2:1 |
| Versorgungsspannung | 3.3 V |
| Ausgangskonfiguration | Differential |
| Output Impedance | 100 ohm |
| Gehäuse | 16-lead WFQFN with exposed pad |
| Montageart | Surface mount |
| Input Interface | Single-ended RF input |
| Operating Frequency Class | Microwave RF |
| Noise Class | Low noise |
| Power Class | Low power |
ADF5000BCPZ-RL7 16-lead wfqfn with exposed pad Pinbelegungsleitfaden
Pinbelegung für ADF5000BCPZ-RL7 (16-lead wfqfn with exposed pad-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für ADF5000BCPZ-RL7.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ADF5000BCPZ-RL7 ist geeignet für 6 Anwendungs: Microwave PLL Feedback Divider, Wireless Transceiver Local Oscillator, Radar Frequency Synthesis, Microwave Test Instrumentation, Satellite Communication RF Chain, Industrial RF Signal Generator.
Microwave PLL Feedback Divider
The ADF5000BCPZ-RL7 fits a PLL feedback path whenever the original microwave signal exceeds the synthesizer’s acceptable prescaler-input range. Its fixed divide-by-2 ratio reduces signals from 4 GHz through 18 GHz to 2 GHz through 9 GHz, while the differential 100-ohm outputs support balanced routing into a compatible RF input. This arrangement preserves a straightforward feedback architecture without requiring programmable divider overhead. The design tradeoff is that the ratio is fixed, so applications needing other integer divisions require a different prescaler.
Empfohlen
Wireless Transceiver Local Oscillator
The ADF5000BCPZ-RL7 is useful in microwave wireless transceivers that need to divide a local-oscillator reference before feeding it into a PLL. Its 18 GHz upper limit accommodates high-band RF feedback, while the low-noise, low-power architecture helps preserve the overall synthesizer performance budget. The differential output can shorten the connection to a balanced PLL input and reduce common-mode pickup along the feedback route. Frequency-range, impedance, and phase-noise requirements must still be evaluated at system level.
Empfohlen
Radar Frequency Synthesis
A radar RF chain can use the ADF5000BCPZ-RL7 to halve a 4 GHz-to-18 GHz feedback signal before applying it to a compatible PLL synthesizer. The fixed divide-by-2 function reduces implementation complexity and supports stable operation when a programmable divider is unnecessary. Differential 100-ohm outputs suit balanced RF routing, but the board designer must control impedance, minimize loop area, and prevent supply or digital coupling from degrading the divider phase-noise contribution.
Empfohlen
Microwave Test Instrumentation
The ADF5000BCPZ-RL7 can divide a microwave source in instrumentation that requires a lower-frequency signal for measurement, phase comparison, or PLL-based generation. The supported 4 GHz-to-18 GHz range makes the device relevant to broadband laboratory and production-test RF systems. Its differential outputs permit balanced connection to suitable test equipment, reducing the need for an unbalanced conversion stage. Calibration and phase-noise measurements should include the divider because its noise and fixed ratio affect the complete instrument chain.
Empfohlen
Satellite Communication RF Chain
The ADF5000BCPZ-RL7 is appropriate for satellite and microwave communication equipment that derives a lower PLL reference from a high-frequency local-oscillator signal. Its fixed 2:1 division can simplify the feedback network, and the differential 100-ohm output supports controlled routing into a balanced synthesizer input. Because communication receivers and transmitters are sensitive to phase noise, the engineer should include the prescaler in the noise budget and assess thermal gradients across the exposed-pad package under the intended operating environment.
Empfohlen
Industrial RF Signal Generator
The ADF5000BCPZ-RL7 supports industrial RF signal-generation systems in which a high-frequency source must be divided before entering a PLL. Its low-power characterization is valuable in compact instrumentation, while the 18 GHz ceiling supports demanding microwave test setups. A balanced RF layout can reduce signal imbalance, but the manufacturer’s ground and exposed-pad requirements must be followed for both electrical stability and heat dissipation. Firmware-controlled frequency changes will still require suitable switching and sequencing around the RF path.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ADF5000BCPZ-RL7 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ADF5000BCPZ |
|---|---|---|
| Package | 16-WFQFN exposed pad | 16-WFQFN exposed pad |
| Brand | Analog Devices | Analog Devices |
| Device Type | Fixed divide-by-2 RF prescaler | Fixed divide-by-2 RF prescaler |
| Input Frequency Range | 4 GHz to 18 GHz | 4 GHz to 18 GHz |
| Maximum Input Frequency | 18 GHz | 18 GHz |
| Division Ratio | 2:1 | 2:1 |
| Supply Voltage | 3.3 V | 3.3 V |
| Output Configuration | Differential | Differential |
| Output Impedance | 100 ohm | 100 ohm |
| Ordering Suffix | RL7 | No RL7 suffix |
Wichtigste Unterscheidungsmerkmale
- Direct fixed division of microwave signals (vs. ADF5000BCPZ)
- Differential RF output architecture (vs. ADF5000BCPZ)
- Low-noise and low-power prescaler positioning (vs. ADF5000BCPZ)
Designhinweise
Route the RF input and differential outputs as controlled-impedance traces using the final PCB stack-up. Keep the prescaler close to the PLL or RF divider interface, minimize branch lengths and stub effects, and preserve symmetry between the two output paths. Place RF-return vias close to the transmission lines and keep supply, control, and unrelated digital traces away from the sensitive input region.
Treat the exposed pad as both an electrical connection and a thermal path. Use the manufacturer land pattern and vias to distribute heat into the surrounding copper, verify junction-temperature limits under the highest expected RF operating condition, and avoid placing the package where a thermal barrier or enclosure airflow reduces heat removal. The available catalog data does not state the exact thermal resistance, so it must be obtained from the manufacturer datasheet.
Keep the supply bypass capacitor close to the device supply and ground terminals, with a very short return path. Follow the datasheet’s component-placement guidance before adding extra filtering, because long or inductive connections can degrade RF behavior. Check whether the exposed pad is tied to ground, supply, or another specified node and implement that connection exactly rather than assuming a generic QFN convention.
Account for the specified 100-ohm differential output impedance when selecting baluns, couplers, and matching elements. Verify the destination device’s input impedance and operating range rather than assuming that every balanced RF input is compatible. For a PLL cascade, measure the complete divider-plus-synthizer phase noise and reference spur performance because the prescaler contributes noise and conversion-related artifacts.
Compliance-Informationen
Compliance declarations were not identified in the manufacturer page excerpt or exact-MPN catalog data. Confirm the current declarations and qualification status with Analog Devices before production release.