ADF5000BCPZ-RL7 - 18 GHz Divide-by-2 RF Prescaler | ADI
MPN: ADF5000BCPZ-RL7 ✓ פעילADF5000BCPZ-RL7 סקירה
An RF prescaler is a frequency-divider block that reduces a high-frequency carrier to a lower frequency that a PLL synthesizer can process. The ADF5000 belongs to the divide-by-2 prescaler category and is positioned within the broader RF frequency-synthesis hierarchy: RF prescaler, divide-by-2 prescaler, frequency divider, clock and timing IC, and semiconductor. Its fixed division ratio simplifies feedback-path design in PLL-based microwave and wireless transmitters.
Key features include a 4 GHz to 18 GHz operating range, a fixed divide-by-2 function, a 3.3 V supply requirement, and differential 100-ohm outputs. The high-frequency input capability is useful when a downstream synthesizer has a limited prescaler input range. The differential output arrangement can simplify impedance matching and reduce susceptibility to common-mode disturbances when the following device provides a differential RF input.
Technically, the ADF5000 divides the RF input by two while preserving the signal path needed by a PLL feedback divider. Analog Devices identifies the ADF5000 as low-noise and low-power, making it appropriate for communication equipment in which divider-added phase noise or excessive power consumption would degrade the overall frequency synthesizer. Its differential outputs are intended to interface directly with RF circuitry designed for balanced operation.
Typical applications include microwave PLL feedback dividers, wireless transceiver local-oscillator synthesis, microwave test equipment, radar and satellite communication chains, and instrumentation requiring frequency division near 18 GHz. The part is particularly relevant when the synthesizer input stage cannot accommodate the original RF frequency but can accept the half-frequency output.
PCB implementation requires careful treatment of the RF input and output paths. Keep the RF traces short, use controlled-impedance routing, and provide the supply decoupling and exposed-pad thermal path specified by the manufacturer. The differential output impedance is 100 ohms, so matching networks and transmission-line geometry should be calculated for the complete board stack-up rather than added by trial and error.
This product page consolidates the device function, operating limits, package constraints, application guidance, and qualification questions into an engineering-oriented reference. It also identifies the limited set of genuinely compatible catalog options, avoiding unrelated dividers that may use the same package family but provide a different division ratio or pin function.
חלופות תחליף ישיר עבור ADF5000BCPZ-RL7 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם ADF5000BCPZ-RL7 (אותו גורם צורה וטביעת רגל) — שונים ב Device Type, Output Impedance.
ADF5000BCPZ
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ADF5000BCPZ-RL7 מפרטים
| Device Type | Fixed divide-by-2 RF prescaler |
| Input Frequency Range | 4 GHz to 18 GHz |
| Maximum RF Input Frequency | 18 GHz |
| Division Ratio | 2:1 |
| מתח אספקה | 3.3 V |
| תצורת מוצא | Differential |
| Output Impedance | 100 ohm |
| מארז | 16-lead WFQFN with exposed pad |
| סוג הרכבה | Surface mount |
| Input Interface | Single-ended RF input |
| Operating Frequency Class | Microwave RF |
| Noise Class | Low noise |
| Power Class | Low power |
מדריך תצורת פינים של ADF5000BCPZ-RL7 16-lead wfqfn with exposed pad
תצורת פינים עבור ADF5000BCPZ-RL7 (מארזת 16-lead wfqfn with exposed pad). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור ADF5000BCPZ-RL7.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
ADF5000BCPZ-RL7 מתאים עבור 6 יישוםs: Microwave PLL Feedback Divider, Wireless Transceiver Local Oscillator, Radar Frequency Synthesis, Microwave Test Instrumentation, Satellite Communication RF Chain, Industrial RF Signal Generator.
Microwave PLL Feedback Divider
The ADF5000BCPZ-RL7 fits a PLL feedback path whenever the original microwave signal exceeds the synthesizer’s acceptable prescaler-input range. Its fixed divide-by-2 ratio reduces signals from 4 GHz through 18 GHz to 2 GHz through 9 GHz, while the differential 100-ohm outputs support balanced routing into a compatible RF input. This arrangement preserves a straightforward feedback architecture without requiring programmable divider overhead. The design tradeoff is that the ratio is fixed, so applications needing other integer divisions require a different prescaler.
מומלץ
Wireless Transceiver Local Oscillator
The ADF5000BCPZ-RL7 is useful in microwave wireless transceivers that need to divide a local-oscillator reference before feeding it into a PLL. Its 18 GHz upper limit accommodates high-band RF feedback, while the low-noise, low-power architecture helps preserve the overall synthesizer performance budget. The differential output can shorten the connection to a balanced PLL input and reduce common-mode pickup along the feedback route. Frequency-range, impedance, and phase-noise requirements must still be evaluated at system level.
מומלץ
Radar Frequency Synthesis
A radar RF chain can use the ADF5000BCPZ-RL7 to halve a 4 GHz-to-18 GHz feedback signal before applying it to a compatible PLL synthesizer. The fixed divide-by-2 function reduces implementation complexity and supports stable operation when a programmable divider is unnecessary. Differential 100-ohm outputs suit balanced RF routing, but the board designer must control impedance, minimize loop area, and prevent supply or digital coupling from degrading the divider phase-noise contribution.
מומלץ
Microwave Test Instrumentation
The ADF5000BCPZ-RL7 can divide a microwave source in instrumentation that requires a lower-frequency signal for measurement, phase comparison, or PLL-based generation. The supported 4 GHz-to-18 GHz range makes the device relevant to broadband laboratory and production-test RF systems. Its differential outputs permit balanced connection to suitable test equipment, reducing the need for an unbalanced conversion stage. Calibration and phase-noise measurements should include the divider because its noise and fixed ratio affect the complete instrument chain.
מומלץ
Satellite Communication RF Chain
The ADF5000BCPZ-RL7 is appropriate for satellite and microwave communication equipment that derives a lower PLL reference from a high-frequency local-oscillator signal. Its fixed 2:1 division can simplify the feedback network, and the differential 100-ohm output supports controlled routing into a balanced synthesizer input. Because communication receivers and transmitters are sensitive to phase noise, the engineer should include the prescaler in the noise budget and assess thermal gradients across the exposed-pad package under the intended operating environment.
מומלץ
Industrial RF Signal Generator
The ADF5000BCPZ-RL7 supports industrial RF signal-generation systems in which a high-frequency source must be divided before entering a PLL. Its low-power characterization is valuable in compact instrumentation, while the 18 GHz ceiling supports demanding microwave test setups. A balanced RF layout can reduce signal imbalance, but the manufacturer’s ground and exposed-pad requirements must be followed for both electrical stability and heat dissipation. Firmware-controlled frequency changes will still require suitable switching and sequencing around the RF path.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור ADF5000BCPZ-RL7 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | ADF5000BCPZ |
|---|---|---|
| Package | 16-WFQFN exposed pad | 16-WFQFN exposed pad |
| Brand | Analog Devices | Analog Devices |
| Device Type | Fixed divide-by-2 RF prescaler | Fixed divide-by-2 RF prescaler |
| Input Frequency Range | 4 GHz to 18 GHz | 4 GHz to 18 GHz |
| Maximum Input Frequency | 18 GHz | 18 GHz |
| Division Ratio | 2:1 | 2:1 |
| Supply Voltage | 3.3 V | 3.3 V |
| Output Configuration | Differential | Differential |
| Output Impedance | 100 ohm | 100 ohm |
| Ordering Suffix | RL7 | No RL7 suffix |
מבדילים עיקריים
- Direct fixed division of microwave signals (לעומתADF5000BCPZ)
- Differential RF output architecture (לעומתADF5000BCPZ)
- Low-noise and low-power prescaler positioning (לעומתADF5000BCPZ)
הערות תכנון
Route the RF input and differential outputs as controlled-impedance traces using the final PCB stack-up. Keep the prescaler close to the PLL or RF divider interface, minimize branch lengths and stub effects, and preserve symmetry between the two output paths. Place RF-return vias close to the transmission lines and keep supply, control, and unrelated digital traces away from the sensitive input region.
Treat the exposed pad as both an electrical connection and a thermal path. Use the manufacturer land pattern and vias to distribute heat into the surrounding copper, verify junction-temperature limits under the highest expected RF operating condition, and avoid placing the package where a thermal barrier or enclosure airflow reduces heat removal. The available catalog data does not state the exact thermal resistance, so it must be obtained from the manufacturer datasheet.
Keep the supply bypass capacitor close to the device supply and ground terminals, with a very short return path. Follow the datasheet’s component-placement guidance before adding extra filtering, because long or inductive connections can degrade RF behavior. Check whether the exposed pad is tied to ground, supply, or another specified node and implement that connection exactly rather than assuming a generic QFN convention.
Account for the specified 100-ohm differential output impedance when selecting baluns, couplers, and matching elements. Verify the destination device’s input impedance and operating range rather than assuming that every balanced RF input is compatible. For a PLL cascade, measure the complete divider-plus-synthizer phase noise and reference spur performance because the prescaler contributes noise and conversion-related artifacts.
מידע על תאימות
Compliance declarations were not identified in the manufacturer page excerpt or exact-MPN catalog data. Confirm the current declarations and qualification status with Analog Devices before production release.