Analog Devices

ADF5000BCPZ-RL7 - 18 GHz Divide-by-2 RF Prescaler | ADI

MPN: ADF5000BCPZ-RL7 ✓ सक्रिय
3.3 V Vdss 16-lead WFQFN with exposed pad Package 4 GHz to 18 GHz Speed
न्यूनतम ऑर्डर मात्रा: 1 |

ADF5000BCPZ-RL7 अवलोकन

The Analog Devices ADF5000BCPZ-RL7 is a fixed divide-by-2 RF prescaler for input frequencies from 4 GHz to 18 GHz, supplied in a 16-lead WFQFN package with an exposed pad and operating from a 3.3 V supply. Its differential 100-ohm RF outputs connect directly to differential RF inputs on frequency-synthesizer and phase-locked-loop circuits.

An RF prescaler is a frequency-divider block that reduces a high-frequency carrier to a lower frequency that a PLL synthesizer can process. The ADF5000 belongs to the divide-by-2 prescaler category and is positioned within the broader RF frequency-synthesis hierarchy: RF prescaler, divide-by-2 prescaler, frequency divider, clock and timing IC, and semiconductor. Its fixed division ratio simplifies feedback-path design in PLL-based microwave and wireless transmitters.

Key features include a 4 GHz to 18 GHz operating range, a fixed divide-by-2 function, a 3.3 V supply requirement, and differential 100-ohm outputs. The high-frequency input capability is useful when a downstream synthesizer has a limited prescaler input range. The differential output arrangement can simplify impedance matching and reduce susceptibility to common-mode disturbances when the following device provides a differential RF input.

Technically, the ADF5000 divides the RF input by two while preserving the signal path needed by a PLL feedback divider. Analog Devices identifies the ADF5000 as low-noise and low-power, making it appropriate for communication equipment in which divider-added phase noise or excessive power consumption would degrade the overall frequency synthesizer. Its differential outputs are intended to interface directly with RF circuitry designed for balanced operation.

Typical applications include microwave PLL feedback dividers, wireless transceiver local-oscillator synthesis, microwave test equipment, radar and satellite communication chains, and instrumentation requiring frequency division near 18 GHz. The part is particularly relevant when the synthesizer input stage cannot accommodate the original RF frequency but can accept the half-frequency output.

PCB implementation requires careful treatment of the RF input and output paths. Keep the RF traces short, use controlled-impedance routing, and provide the supply decoupling and exposed-pad thermal path specified by the manufacturer. The differential output impedance is 100 ohms, so matching networks and transmission-line geometry should be calculated for the complete board stack-up rather than added by trial and error.

This product page consolidates the device function, operating limits, package constraints, application guidance, and qualification questions into an engineering-oriented reference. It also identifies the limited set of genuinely compatible catalog options, avoiding unrelated dividers that may use the same package family but provide a different division ratio or pin function.

के लिए ड्रॉप-इन विकल्प ADF5000BCPZ-RL7 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं ADF5000BCPZ-RL7 (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Device Type, Output Impedance.

Analog Devices
Device Type: Fixed RF divide-by-2 prescaler
Output Impedance: 100 ohm differential
इसके साथ तुलना करें ADF5000BCPZ-RL7 →

ADF5000BCPZ

✅ ड्रॉप-इन
Analog Devices
📦 16-WFQFN exposed pad
Fixed RF divide-by-2 prescaler · 18 GHz · 4 GHz · 2:1 · 3.3 V · Differential RF · 100 ohm differential · 1 differential output

कीमत के लिए संपर्क करें

डेटाशीट देखें →

ADF5000BCPZ-RL7 विशेषताएं

Device Type Fixed divide-by-2 RF prescaler
Input Frequency Range 4 GHz to 18 GHz
Maximum RF Input Frequency 18 GHz
Division Ratio 2:1
सप्लाई वोल्टेज 3.3 V
आउटपुट कॉन्फ़िगरेशन Differential
Output Impedance 100 ohm
पैकेज 16-lead WFQFN with exposed pad
माउंटिंग प्रकार Surface mount
Input Interface Single-ended RF input
Operating Frequency Class Microwave RF
Noise Class Low noise
Power Class Low power

ADF5000BCPZ-RL7 16-lead wfqfn with exposed pad पिन कॉन्फ़िगरेशन गाइड

ADF5000BCPZ-RL7 (16-lead wfqfn with exposed pad पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

ADF5000BCPZ-RL7 के लिए 16-lead wfqfn with exposed pad पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ADF5000BCPZ-RL7.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

ADF5000BCPZ-RL7 के लिए उपयुक्त है 6 अनुप्रयोगs: Microwave PLL Feedback Divider, Wireless Transceiver Local Oscillator, Radar Frequency Synthesis, Microwave Test Instrumentation, Satellite Communication RF Chain, Industrial RF Signal Generator.

🌐

Microwave PLL Feedback Divider

The ADF5000BCPZ-RL7 fits a PLL feedback path whenever the original microwave signal exceeds the synthesizer’s acceptable prescaler-input range. Its fixed divide-by-2 ratio reduces signals from 4 GHz through 18 GHz to 2 GHz through 9 GHz, while the differential 100-ohm outputs support balanced routing into a compatible RF input. This arrangement preserves a straightforward feedback architecture without requiring programmable divider overhead. The design tradeoff is that the ratio is fixed, so applications needing other integer divisions require a different prescaler.

📱

Wireless Transceiver Local Oscillator

The ADF5000BCPZ-RL7 is useful in microwave wireless transceivers that need to divide a local-oscillator reference before feeding it into a PLL. Its 18 GHz upper limit accommodates high-band RF feedback, while the low-noise, low-power architecture helps preserve the overall synthesizer performance budget. The differential output can shorten the connection to a balanced PLL input and reduce common-mode pickup along the feedback route. Frequency-range, impedance, and phase-noise requirements must still be evaluated at system level.

✈️

Radar Frequency Synthesis

A radar RF chain can use the ADF5000BCPZ-RL7 to halve a 4 GHz-to-18 GHz feedback signal before applying it to a compatible PLL synthesizer. The fixed divide-by-2 function reduces implementation complexity and supports stable operation when a programmable divider is unnecessary. Differential 100-ohm outputs suit balanced RF routing, but the board designer must control impedance, minimize loop area, and prevent supply or digital coupling from degrading the divider phase-noise contribution.

🖥️

Microwave Test Instrumentation

The ADF5000BCPZ-RL7 can divide a microwave source in instrumentation that requires a lower-frequency signal for measurement, phase comparison, or PLL-based generation. The supported 4 GHz-to-18 GHz range makes the device relevant to broadband laboratory and production-test RF systems. Its differential outputs permit balanced connection to suitable test equipment, reducing the need for an unbalanced conversion stage. Calibration and phase-noise measurements should include the divider because its noise and fixed ratio affect the complete instrument chain.

🛰️

Satellite Communication RF Chain

The ADF5000BCPZ-RL7 is appropriate for satellite and microwave communication equipment that derives a lower PLL reference from a high-frequency local-oscillator signal. Its fixed 2:1 division can simplify the feedback network, and the differential 100-ohm output supports controlled routing into a balanced synthesizer input. Because communication receivers and transmitters are sensitive to phase noise, the engineer should include the prescaler in the noise budget and assess thermal gradients across the exposed-pad package under the intended operating environment.

🏭

Industrial RF Signal Generator

The ADF5000BCPZ-RL7 supports industrial RF signal-generation systems in which a high-frequency source must be divided before entering a PLL. Its low-power characterization is valuable in compact instrumentation, while the 18 GHz ceiling supports demanding microwave test setups. A balanced RF layout can reduce signal imbalance, but the manufacturer’s ground and exposed-pad requirements must be followed for both electrical stability and heat dissipation. Firmware-controlled frequency changes will still require suitable switching and sequencing around the RF path.

What is the operating frequency range of ADF5000BCPZ-RL7?
The ADF5000BCPZ-RL7 operates from 4 GHz to 18 GHz as a fixed divide-by-2 RF prescaler. According to the Analog Devices ADF5000 datasheet, it is intended to divide high microwave frequencies down to a level suitable for the input of a PLL frequency synthesizer. Its 18 GHz upper operating limit makes it applicable to microwave communication, radar, test-equipment, and wireless-transceiver feedback paths.
How does the ADF5000BCPZ-RL7 divide an RF signal?
The ADF5000BCPZ-RL7 provides a fixed divide-by-2 function, so a 10 GHz input produces a 5 GHz divided output within the supported input range. The Analog Devices ADF5000 datasheet describes the device as a fixed RF divider block for reducing frequencies as high as 18 GHz. This fixed ratio avoids programmable divider overhead and is suited to PLL feedback paths where a constant division ratio is sufficient.
What is the supply voltage of the ADF5000BCPZ-RL7?
The ADF5000BCPZ-RL7 operates from a 3.3 V supply. According to the Analog Devices ADF5000 datasheet, this single supply supports the low-noise, low-power prescaler core and its differential RF outputs. Board-level implementation should include local supply decoupling and verify the regulator’s transient performance against the operating current required by the completed RF layout.
Where can I download the ADF5000BCPZ-RL7 datasheet PDF?
The official ADF5000 datasheet PDF is available from Analog Devices at the manufacturer data-sheet URL on this product page. The document covers the 4 GHz to 18 GHz divide-by-2 operation, 3.3 V supply, differential 100-ohm outputs, package information, and application guidance. Use the manufacturer PDF for the authoritative pin descriptions, electrical characteristics, and exposed-pad connection details.
Where can I find the ADF5000BCPZ-RL7 pinout?
The pinout is shown in the Analog Devices ADF5000 manufacturer datasheet under the package and pin-configuration information. The catalog description identifies the device as a 16-lead WFQFN with exposed pad. Use the datasheet pin-description table when assigning RF, supply, ground, and exposed-pad connections because generic QFN drawings may not preserve the function assigned to every terminal.
Can the ADF5000BCPZ-RL7 interface directly with a differential PLL input?
Yes, the ADF5000BCPZ-RL7 is designed with differential 100-ohm RF outputs for direct connection to a compatible differential RF input. Analog Devices identifies ADF4156 and ADF4106 examples of PLL ICs suitable for receiving a divided frequency. The actual interface still requires verification of impedance, DC bias, bandwidth, and whether the destination input accepts a prescaler output directly or needs a coupling network.
What is the best drop-in replacement for ADF5000BCPZ-RL7?
The closest catalog option is the ADF5000BCPZ, which is the same ADF5000 device without the RL7 ordering suffix and retains the 18 GHz divide-by-2 function. Compatibility should still be confirmed against temperature-grade, tape-and-reel, and ordering requirements before substitution. No independently documented cross-brand, pin-to-pin equivalent was established, so similarly packaged RF dividers with different ratios are not true drop-in replacements.
What can replace ADF5000BCPZ-RL7?
ADF5000BCPZ is the closest functional replacement because it retains the same ADF5000 4 GHz-to-18 GHz divide-by-2 function and 16-lead WFQFN exposed-pad package. The RL7 suffix identifies a specific ordering configuration, so procurement should verify packing and qualification requirements. Parts such as the ADF5001 or ADF5002 are not automatic replacements because their division functions differ.
ADF5000BCPZ-RL7 vs ADF5000BCPZ — which version should I select?
Select ADF5000BCPZ-RL7 when the RL7 ordering configuration is required; select ADF5000BCPZ when that ordering code is acceptable and the alternate catalog configuration meets the procurement specification. Both correspond to the ADF5000 18 GHz divide-by-2 prescaler. The key selection checks are the exact MPN, package, temperature grade, delivery format, and any qualification requirements stated in the manufacturer ordering guide.
When should I choose ADF5000BCPZ-RL7 over another RF prescaler?
Choose ADF5000BCPZ-RL7 when the design needs a fixed divide-by-2 operation across 4 GHz to 18 GHz, a 3.3 V supply, and differential 100-ohm outputs. It is particularly appropriate for a PLL feedback divider whose input cannot accept the original microwave frequency. Choose a different prescaler when programmable division, a different ratio, another frequency band, or different electrical limits are required.
Is ADF5000BCPZ-RL7 suitable for a wireless transceiver?
Yes, the ADF5000BCPZ-RL7 is suitable for microwave RF feedback paths in wireless transceivers when a divide-by-2 ratio and 4 GHz-to-18 GHz input range meet the local-oscillator requirements. Its low-noise, low-power characterization is important because divider noise and power consumption contribute directly to synthesizer performance. The complete design must still meet applicable RF, thermal, and regulatory requirements.
Is ADF5000BCPZ-RL7 in stock and what is its lead time?
Current stock and lead time should be requested through the Request a Quote form on this page. The Analog Devices product page and the exact-MPN catalog listing establish product identity, but they do not provide a guaranteed current manufacturing allocation. The form is the appropriate route for checking lot availability, minimum order quantity, delivery timing, and the required reel configuration.
Where can I buy ADF5000BCPZ-RL7?
Use the Request a Quote form on this page to request ADF5000BCPZ-RL7, current availability, and delivery details. The exact orderable MPN is the Analog Devices 18 GHz divide-by-2 prescaler in a 16-lead WFQFN exposed-pad package. A valid procurement request should identify the required quantity, reel configuration, acceptable delivery date, and any automotive or industrial qualification requirements.
What is the price of ADF5000BCPZ-RL7?
Request current ADF5000BCPZ-RL7 pricing through the Request a Quote form on this page. The commercial response should reflect the exact MPN, quantity, reel configuration, and requested delivery schedule. Quote-based handling is appropriate because component pricing and lead time can vary with order quantity, market conditions, and packaging requirements.
What are the key specifications engineers should know about ADF5000BCPZ-RL7?
The ADF5000BCPZ-RL7 is a low-noise, low-power fixed RF prescaler covering 4 GHz to 18 GHz. Its division ratio is 2:1, its supply is 3.3 V, and its output is differential with a 100-ohm impedance. The package is a 16-lead WFQFN with an exposed pad. These parameters define its primary use in microwave PLL and frequency-synthesizer feedback paths.

के लिए इंजीनियरिंग संदर्भ डेटा ADF5000BCPZ-RL7 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose ADF5000BCPZ-RL7 when the design requires a fixed 4 GHz-to-18 GHz divide-by-2 prescaler, a 3.3 V supply, and differential 100-ohm RF outputs, particularly in a balanced PLL feedback path. ADF5000BCPZ is the closest alternate ordering configuration and retains the same stated core specifications, but the suffix must be reconciled with the required packing, temperature grade, and procurement format. Do not substitute a generic 16-pin QFN prescaler merely because its outline matches: the division ratio, RF frequency range, supply requirements, differential-output impedance, and pin assignments must all be compatible. A programmable or divide-by-other prescaler should be selected instead when the system needs adjustable division or a ratio other than 2:1.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद ADF5000BCPZ
Package 16-WFQFN exposed pad 16-WFQFN exposed pad
Brand Analog Devices Analog Devices
Device Type Fixed divide-by-2 RF prescaler Fixed divide-by-2 RF prescaler
Input Frequency Range 4 GHz to 18 GHz 4 GHz to 18 GHz
Maximum Input Frequency 18 GHz 18 GHz
Division Ratio 2:1 2:1
Supply Voltage 3.3 V 3.3 V
Output Configuration Differential Differential
Output Impedance 100 ohm 100 ohm
Ordering Suffix RL7 No RL7 suffix

मुख्य विशेषताएँ

  • Direct fixed division of microwave signals (बनामADF5000BCPZ)
  • Differential RF output architecture (बनामADF5000BCPZ)
  • Low-noise and low-power prescaler positioning (बनामADF5000BCPZ)

डिज़ाइन नोट्स

Route the RF input and differential outputs as controlled-impedance traces using the final PCB stack-up. Keep the prescaler close to the PLL or RF divider interface, minimize branch lengths and stub effects, and preserve symmetry between the two output paths. Place RF-return vias close to the transmission lines and keep supply, control, and unrelated digital traces away from the sensitive input region.

Treat the exposed pad as both an electrical connection and a thermal path. Use the manufacturer land pattern and vias to distribute heat into the surrounding copper, verify junction-temperature limits under the highest expected RF operating condition, and avoid placing the package where a thermal barrier or enclosure airflow reduces heat removal. The available catalog data does not state the exact thermal resistance, so it must be obtained from the manufacturer datasheet.

Keep the supply bypass capacitor close to the device supply and ground terminals, with a very short return path. Follow the datasheet’s component-placement guidance before adding extra filtering, because long or inductive connections can degrade RF behavior. Check whether the exposed pad is tied to ground, supply, or another specified node and implement that connection exactly rather than assuming a generic QFN convention.

Account for the specified 100-ohm differential output impedance when selecting baluns, couplers, and matching elements. Verify the destination device’s input impedance and operating range rather than assuming that every balanced RF input is compatible. For a PLL cascade, measure the complete divider-plus-synthizer phase noise and reference spur performance because the prescaler contributes noise and conversion-related artifacts.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

Compliance declarations were not identified in the manufacturer page excerpt or exact-MPN catalog data. Confirm the current declarations and qualification status with Analog Devices before production release.

डेटा सत्यापन तिथि: 2026-11-20 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

ADF5000BCPZ-RL7 datasheet ADF5000BCPZ-RL7 pinout ADF5000BCPZ-RL7 datasheet pdf ADF5000BCPZ-RL7 equivalent ADF5000BCPZ-RL7 replacement ADF5000BCPZ-RL7 schematic ADF5000BCPZ-RL7 price ADF5000BCPZ-RL7 stock Analog Devices ADF5000BCPZ-RL7 ADF5000 18 GHz divide by 2 prescaler ADF5000BCPZ-RL7 vs ADF5000BCPZ ADF5000BCPZ 16-WFQFN pinout

संबंधित कंपोनेंट्स और शब्द

Analog Devices ADF5000BCPZ-RL7 ADF5000BCPZ ADF4156 ADF4106 RF prescaler divide-by-2 prescaler frequency divider phase-locked loop PLL frequency synthesizer differential RF output 3.3 V supply 100-ohm impedance 18 GHz 4 GHz 16-WFQFN QFN family surface mount SMD microwave frequency synthesis low-noise prescaler wireless transceiver radar RoHS REACH AEC-Q100
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें