ADF5000BCPZ-RL7 - 18 GHz Divide-by-2 RF Prescaler | ADI
部品番号: ADF5000BCPZ-RL7 ✓ 生産中ADF5000BCPZ-RL7 概要
An RF prescaler is a frequency-divider block that reduces a high-frequency carrier to a lower frequency that a PLL synthesizer can process. The ADF5000 belongs to the divide-by-2 prescaler category and is positioned within the broader RF frequency-synthesis hierarchy: RF prescaler, divide-by-2 prescaler, frequency divider, clock and timing IC, and semiconductor. Its fixed division ratio simplifies feedback-path design in PLL-based microwave and wireless transmitters.
Key features include a 4 GHz to 18 GHz operating range, a fixed divide-by-2 function, a 3.3 V supply requirement, and differential 100-ohm outputs. The high-frequency input capability is useful when a downstream synthesizer has a limited prescaler input range. The differential output arrangement can simplify impedance matching and reduce susceptibility to common-mode disturbances when the following device provides a differential RF input.
Technically, the ADF5000 divides the RF input by two while preserving the signal path needed by a PLL feedback divider. Analog Devices identifies the ADF5000 as low-noise and low-power, making it appropriate for communication equipment in which divider-added phase noise or excessive power consumption would degrade the overall frequency synthesizer. Its differential outputs are intended to interface directly with RF circuitry designed for balanced operation.
Typical applications include microwave PLL feedback dividers, wireless transceiver local-oscillator synthesis, microwave test equipment, radar and satellite communication chains, and instrumentation requiring frequency division near 18 GHz. The part is particularly relevant when the synthesizer input stage cannot accommodate the original RF frequency but can accept the half-frequency output.
PCB implementation requires careful treatment of the RF input and output paths. Keep the RF traces short, use controlled-impedance routing, and provide the supply decoupling and exposed-pad thermal path specified by the manufacturer. The differential output impedance is 100 ohms, so matching networks and transmission-line geometry should be calculated for the complete board stack-up rather than added by trial and error.
This product page consolidates the device function, operating limits, package constraints, application guidance, and qualification questions into an engineering-oriented reference. It also identifies the limited set of genuinely compatible catalog options, avoiding unrelated dividers that may use the same package family but provide a different division ratio or pin function.
ドロップイン代替品: ADF5000BCPZ-RL7 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ADF5000BCPZ-RL7 (同一形状・フットプリント) — 相違点: Device Type, Output Impedance.
ADF5000BCPZ
✅ ドロップイン価格はお問い合わせください
データシートを見る →ADF5000BCPZ-RL7 仕様
| Device Type | Fixed divide-by-2 RF prescaler |
| Input Frequency Range | 4 GHz to 18 GHz |
| Maximum RF Input Frequency | 18 GHz |
| Division Ratio | 2:1 |
| 電源電圧 | 3.3 V |
| 出力構成 | Differential |
| Output Impedance | 100 ohm |
| パッケージ | 16-lead WFQFN with exposed pad |
| 実装タイプ | Surface mount |
| Input Interface | Single-ended RF input |
| Operating Frequency Class | Microwave RF |
| Noise Class | Low noise |
| Power Class | Low power |
ADF5000BCPZ-RL7 16-lead wfqfn with exposed pad ピン配置ガイド
ADF5000BCPZ-RL7 (16-lead wfqfn with exposed pad パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: ADF5000BCPZ-RL7.
詳細は データシート をご参照ください。
主な用途
ADF5000BCPZ-RL7 の用途: 6 件s: Microwave PLL Feedback Divider, Wireless Transceiver Local Oscillator, Radar Frequency Synthesis, Microwave Test Instrumentation, Satellite Communication RF Chain, Industrial RF Signal Generator.
Microwave PLL Feedback Divider
The ADF5000BCPZ-RL7 fits a PLL feedback path whenever the original microwave signal exceeds the synthesizer’s acceptable prescaler-input range. Its fixed divide-by-2 ratio reduces signals from 4 GHz through 18 GHz to 2 GHz through 9 GHz, while the differential 100-ohm outputs support balanced routing into a compatible RF input. This arrangement preserves a straightforward feedback architecture without requiring programmable divider overhead. The design tradeoff is that the ratio is fixed, so applications needing other integer divisions require a different prescaler.
おすすめ
Wireless Transceiver Local Oscillator
The ADF5000BCPZ-RL7 is useful in microwave wireless transceivers that need to divide a local-oscillator reference before feeding it into a PLL. Its 18 GHz upper limit accommodates high-band RF feedback, while the low-noise, low-power architecture helps preserve the overall synthesizer performance budget. The differential output can shorten the connection to a balanced PLL input and reduce common-mode pickup along the feedback route. Frequency-range, impedance, and phase-noise requirements must still be evaluated at system level.
おすすめ
Radar Frequency Synthesis
A radar RF chain can use the ADF5000BCPZ-RL7 to halve a 4 GHz-to-18 GHz feedback signal before applying it to a compatible PLL synthesizer. The fixed divide-by-2 function reduces implementation complexity and supports stable operation when a programmable divider is unnecessary. Differential 100-ohm outputs suit balanced RF routing, but the board designer must control impedance, minimize loop area, and prevent supply or digital coupling from degrading the divider phase-noise contribution.
おすすめ
Microwave Test Instrumentation
The ADF5000BCPZ-RL7 can divide a microwave source in instrumentation that requires a lower-frequency signal for measurement, phase comparison, or PLL-based generation. The supported 4 GHz-to-18 GHz range makes the device relevant to broadband laboratory and production-test RF systems. Its differential outputs permit balanced connection to suitable test equipment, reducing the need for an unbalanced conversion stage. Calibration and phase-noise measurements should include the divider because its noise and fixed ratio affect the complete instrument chain.
おすすめ
Satellite Communication RF Chain
The ADF5000BCPZ-RL7 is appropriate for satellite and microwave communication equipment that derives a lower PLL reference from a high-frequency local-oscillator signal. Its fixed 2:1 division can simplify the feedback network, and the differential 100-ohm output supports controlled routing into a balanced synthesizer input. Because communication receivers and transmitters are sensitive to phase noise, the engineer should include the prescaler in the noise budget and assess thermal gradients across the exposed-pad package under the intended operating environment.
おすすめ
Industrial RF Signal Generator
The ADF5000BCPZ-RL7 supports industrial RF signal-generation systems in which a high-frequency source must be divided before entering a PLL. Its low-power characterization is valuable in compact instrumentation, while the 18 GHz ceiling supports demanding microwave test setups. A balanced RF layout can reduce signal imbalance, but the manufacturer’s ground and exposed-pad requirements must be followed for both electrical stability and heat dissipation. Firmware-controlled frequency changes will still require suitable switching and sequencing around the RF path.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: ADF5000BCPZ-RL7 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ADF5000BCPZ |
|---|---|---|
| Package | 16-WFQFN exposed pad | 16-WFQFN exposed pad |
| Brand | Analog Devices | Analog Devices |
| Device Type | Fixed divide-by-2 RF prescaler | Fixed divide-by-2 RF prescaler |
| Input Frequency Range | 4 GHz to 18 GHz | 4 GHz to 18 GHz |
| Maximum Input Frequency | 18 GHz | 18 GHz |
| Division Ratio | 2:1 | 2:1 |
| Supply Voltage | 3.3 V | 3.3 V |
| Output Configuration | Differential | Differential |
| Output Impedance | 100 ohm | 100 ohm |
| Ordering Suffix | RL7 | No RL7 suffix |
主な差別化要因
- Direct fixed division of microwave signals (vs ADF5000BCPZ)
- Differential RF output architecture (vs ADF5000BCPZ)
- Low-noise and low-power prescaler positioning (vs ADF5000BCPZ)
設計ノート
Route the RF input and differential outputs as controlled-impedance traces using the final PCB stack-up. Keep the prescaler close to the PLL or RF divider interface, minimize branch lengths and stub effects, and preserve symmetry between the two output paths. Place RF-return vias close to the transmission lines and keep supply, control, and unrelated digital traces away from the sensitive input region.
Treat the exposed pad as both an electrical connection and a thermal path. Use the manufacturer land pattern and vias to distribute heat into the surrounding copper, verify junction-temperature limits under the highest expected RF operating condition, and avoid placing the package where a thermal barrier or enclosure airflow reduces heat removal. The available catalog data does not state the exact thermal resistance, so it must be obtained from the manufacturer datasheet.
Keep the supply bypass capacitor close to the device supply and ground terminals, with a very short return path. Follow the datasheet’s component-placement guidance before adding extra filtering, because long or inductive connections can degrade RF behavior. Check whether the exposed pad is tied to ground, supply, or another specified node and implement that connection exactly rather than assuming a generic QFN convention.
Account for the specified 100-ohm differential output impedance when selecting baluns, couplers, and matching elements. Verify the destination device’s input impedance and operating range rather than assuming that every balanced RF input is compatible. For a PLL cascade, measure the complete divider-plus-synthizer phase noise and reference spur performance because the prescaler contributes noise and conversion-related artifacts.
コンプライアンス情報
Compliance declarations were not identified in the manufacturer page excerpt or exact-MPN catalog data. Confirm the current declarations and qualification status with Analog Devices before production release.