ISL9103AIRUCZ-T - 500mA 2.4MHz Sync Buck 1.8V Fixed | Renesas
Teilenummer: ISL9103AIRUCZ-T ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $1.95 | $1,95 |
| 10 | $1.72 | $17,20 |
| 100 | $1.48 | $148,00 |
| 500 | $1.27 | $635,00 |
| 1.000 | $1.1 | $1.100,00 |
| 3.000 | $0.95 | $2.850,00 |
ISL9103AIRUCZ-T Übersicht
A buck switching regulator (also called a step-down converter) is a switch-mode power supply topology that converts a higher DC input voltage into a lower DC output voltage by periodically switching an inductor and rectifying the resulting waveform. Buck regulators occupy the power management IC category alongside LDOs, boost converters, and charge pumps, and are preferred over LDOs whenever input-to-output voltage differential is large because they can exceed 90% efficiency. The ISL9103A family targets low-power point-of-load rails in portable, battery-powered devices where board space is at a premium.
Key features include a typical quiescent current that supports long battery standby, 2.4 MHz PWM switching that enables a sub-1 mm profile inductor, internal synchronous rectification that eliminates the external Schottky diode, and built-in protection including overcurrent, thermal shutdown, and soft-start. The 6-pin UTDFN occupies only 1.6 x 1.6 mm of board area, making it suitable for sub-30 mm square power sections in wearables, handsets, and IoT endpoints.
The device uses a peak-current-mode PWM control architecture with internal compensation, simplifying external design and providing predictable small-signal response across line and load variation. Internal MOSFETs and synchronous rectification eliminate the need for an external Schottky, while 100% duty cycle extends usable input range when the battery droops toward the output setpoint.
Typical applications include powering low-voltage microprocessors in PDAs and cellular phones, single-cell Li+ battery rails in portable media players, and as a post-DCDC point-of-load regulator for application processors in handheld products.
A key design consideration is the 2.4 MHz switching frequency: the inductor can be small (typically 1.0 to 2.2 uH), but PCB layout must minimize the input/output loop area to limit radiated EMI from the switching node.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Drop-in-Alternativen für ISL9103AIRUCZ-T – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
ISL9103IRUCZ-T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ISL9104IRUCZ-T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ISL9105IRUCZ-T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ISL9103AIRUCZ-T Grenzwerte & elektrische Eigenschaften
| Topologie | Synchronous Step-Down (Buck) |
| Eingangsspannungsbereich | 2.7 V to 6 V |
| Ausgangsspannung | 1.8 V (fixed) |
| Maximaler Ausgangsstrom | 500 mA |
| Schaltfrequenz | 2.4 MHz (typical) |
| Dropout-Spannung | less than 300 mV at 500 mA |
| Ruhestrom | Low-IQ (value in datasheet) |
| Internal MOSFETs | P-channel high-side + N-channel low-side synchronous pair |
| Duty Cycle Range | 0% to 100% (100% duty cycle operation) |
| Control Architecture | Peak current-mode PWM |
| Minimum Output Voltage | 0.8 V (family capability, this part fixed at 1.8 V) |
| Gehäuse | 6-pin UTDFN (UFDFN) 1.6 x 1.6 mm |
| Montageart | Surface Mount |
| RoHS-Status | Compliant (per distributor listing) |
ISL9103AIRUCZ-T 6-pin utdfn (ufdfn) 1.6 x 1.6 mm Pinbelegungsleitfaden
Pinbelegung für ISL9103AIRUCZ-T (6-pin utdfn (ufdfn) 1.6 x 1.6 mm-Gehäuse). Dieses Leistungsbauteil verfügt über Gate-, Drain- und Source-Anschlüsse. Bei nicht gepolten Gehäusen entnehmen Sie die genaue Ausrichtung von Pin 1 und Footprint-Details dem Herstellerdatenblatt. Typische Anwendungen sind Netzteilentwurf, Motoransteuerung und Lastschaltung.
Keine detaillierten Pinbelegungsdaten verfügbar für ISL9103AIRUCZ-T.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ISL9103AIRUCZ-T ist geeignet für 6 Anwendungs: Cellular Phone Baseband Power Rail, PDA / Handheld Processor Power, Single-Cell Li-Ion Portable Media Player, Wearable / IoT Sensor Node Power, Point-of-Load for Application Processor, Industrial Handheld Terminal.
Cellular Phone Baseband Power Rail
The ISL9103AIRUCZ-T is purpose-built for 1.8 V / 500 mA point-of-load rails inside cellular phone baseband subsystems. Its 2.4 MHz switching frequency permits a 1.0 to 2.2 uH chip inductor less than 1 mm tall, freeing PCB real estate for the RF shield and antenna. Synchronous rectification keeps efficiency above 90% at 200 to 400 mA typical baseband load, and the integrated MOSFETs remove the need for any external Schottky. Place the input cap within 2 mm of the VIN pad and route the LX node away from sensitive RF traces to avoid conducted noise coupling into the receive path.
Empfohlen
PDA / Handheld Processor Power
Handheld PDAs and organizer-style devices run application processors at 1.8 V core voltage drawing up to 500 mA under active load. The ISL9103AIRUCZ-T's fixed 1.8 V output and 2.4 MHz switching deliver the rail cleanly with only three external components: a 2.2 uH inductor, a 4.7 uF input cap, and a 10 uF output cap. Its less-than-300 mV dropout at 500 mA extends usable Li-ion runtime when the cell sags to 2.1 V. The 1.6 x 1.6 mm UTDFN package fits easily beside the processor BGA on the underside of the main board.
Empfohlen
Single-Cell Li-Ion Portable Media Player
Portable media players and MP3 players rely on a single Li-ion cell ranging from 4.2 V fully charged to 3.0 V end-of-discharge. The ISL9103AIRUCZ-T accepts this full 3.0 V to 4.2 V range and produces a stable 1.8 V at 500 mA for the audio DAC, codec, and baseband logic. Synchronous rectification keeps light-load efficiency high, important for standby runtime where the audio subsystem idles. The 6-pin UTDFN enables mounting under the battery tab without intruding into the audio path layout.
Empfohlen
Wearable / IoT Sensor Node Power
Battery-powered wearables and IoT sensor nodes require sub-30 mm square power sections that can sustain days or weeks of standby. The ISL9103AIRUCZ-T's low-IQ design minimizes quiescent drain, while its 1.6 x 1.6 mm UTDFN footprint and 2.4 MHz switching allow the entire converter to occupy less than 10 mm square including the inductor. Running from a 3.7 V Li-Po or two alkaline cells in series, it provides 1.8 V to a BLE radio, microcontroller, and sensor front-end. Synchronous PEX and high-side P-FET ensure clean cold-start with the load already present.
Empfohlen
Point-of-Load for Application Processor
After a main 3.3 V or 5 V buck, system boards often require a localized 1.8 V rail for application processor I/O or peripheral logic. The ISL9103AIRUCZ-T serves as a compact post-regulator, taking the intermediate rail and delivering clean 1.8 V at 500 mA to the SoC's GPIO bank or external flash. Its 2.4 MHz switching is offset from typical 1 MHz intermediate rails, reducing beat-frequency noise. The internal soft-start prevents inrush when the upstream rail is already energized.
Empfohlen
Industrial Handheld Terminal
Industrial barcode scanners, rugged PDAs, and field-service terminals need reliable 1.8 V rails across a wider temperature range than consumer handsets. The ISL9103AIRUCZ-T's synchronous buck architecture produces less heat than an LDO at the same load, improving long-term reliability in sealed enclosures. Operating from a 2.7 V to 6 V input accommodates single Li-ion packs, two- or three-cell battery boxes, and regulated 5 V USB inputs. The exposed pad on the 6-pin UTDFN provides solid thermal contact with the inner ground plane.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ISL9103AIRUCZ-T – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ISL9103IRUCZ-T | ISL9104IRUCZ-T | ISL9105IRUCZ-T |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 6-pin UTDFN 1.6x1.6 mm | 6-pin UTDFN - same | 6-pin UTDFN - same | 6-pin UTDFN - same |
| Topology | Synchronous Buck | Synchronous Buck | Synchronous Buck | Synchronous Buck |
| Input Voltage Range | 2.7 V to 6 V | 2.7 V to 6 V | 2.7 V to 6 V | 2.7 V to 6 V |
| Output Voltage | 1.8 V (fixed) | Different fixed voltage (verify suffix) | Different fixed voltage (verify suffix) | Different fixed voltage (verify suffix) |
| Internal MOSFETs | P-FET high-side + N-FET low-side synchronous | Same architecture | Same architecture | Same architecture |
Wichtigste Unterscheidungsmerkmale
- Newer-generation -A suffix optimized for low-IQ and high light-load efficiency (vs. ISL9103IRUCZ-T)
- Tape-and-reel -T suffix for high-volume production lines (vs. ISL9103AIRUCZ (tray version))
- Fixed 1.8 V output eliminates external feedback divider (vs. ISL9104IRUCZ-T / ISL9105IRUCZ-T (different fixed voltages))
Designhinweise
Place the input capacitor within 2 mm of the VIN and GND pads to minimize high-frequency loop area. Route the LX (switch node) trace on a single layer away from sensitive analog signals; avoid running LX under the IC or under feedback traces. Use a solid ground pour directly under the exposed pad of the UTDFN to provide thermal sinking and low-impedance return for the synchronous rectifier.
Keep the feedback and output-sense traces short and shielded by ground copper on both sides. For the 1.8 V fixed version no external feedback divider is required, but routing the VOUT sense directly to the load side of the output capacitor (Kelvin connection) improves transient response to load steps. Avoid vias in the high-current input and LX paths; if unavoidable, use 2 to 3 parallel vias to limit inductance.
Do not use a through-hole inductor; the 2.4 MHz switching requires a low-DCR, low-AC-resistance chip inductor of 1.0 to 2.2 uH with a saturation current rating above 1 A (per Renesas datasheet). Using an undersized inductor causes severe ringing at LX and may trigger OCP. Also verify the output capacitor's ESR and voltage rating; a 10 uF X5R 6.3V ceramic is the typical choice. Operating below the minimum 2.7 V input can prevent startup or cause the LX node to stay stuck high.
Compliance-Informationen
RoHS and lead-free per Renesas product listing. Automotive AEC-Q100 qualification status not confirmed in available data; check full datasheet for industrial/automotive grade options.
