Microchip Technology

KSZ8794CNXCC - 4-Port 10/100 Managed Ethernet Switch | Microchip

Teilenummer: KSZ8794CNXCC ✓ Aktiv
3.3 V Vdss 64-pin QFN Package
MOQ: 1 |

KSZ8794CNXCC Übersicht

The Microchip Technology KSZ8794CNXCC is a Layer 2 managed Ethernet switch with four 10/100 Mb/s copper ports and a Gigabit RGMII/MII/RMII uplink interface, housed in a 64-pin QFN package measuring 8 mm by 8 mm. Three ports support 10/100 Mb/s Ethernet, while the fourth provides a 10/100/1000 Mb/s Gigabit uplink. The device operates from a 3.3 V supply and combines copper-port PHYs, switching logic, and uplink control in one package.

An Ethernet switch is a Layer 2 network component that receives Ethernet frames, examines destination addresses, and forwards traffic through the appropriate physical port. The KSZ8794CNXCC belongs to the managed-switch hierarchy, combining integrated 10/100 Base-T/TX PHYs with management features designed to reduce the component count and board area required for multiport industrial or embedded Ethernet equipment.

The principal features are four integrated copper Ethernet ports, a configurable Gigabit uplink, support for RGMII, MII, and RMII host interfaces, internal biasing, and on-chip termination. Its 8 mm by 8 mm QFN-64 package supports compact designs while exposing high-speed network connectivity without requiring four discrete Ethernet PHYs. The managed Layer 2 architecture is suitable for systems that need controlled forwarding behavior rather than only basic hub functionality.

The uplink architecture allows a lower-cost 10/100 Mb/s access network to connect to a faster Gigabit backbone through a single high-speed host interface. RGMII supports parallel high-speed signaling, MII is a lower-speed parallel interface, and RMII reduces the number of host-side signals. Designers should select the interface according to the host processor, signal-rate requirements, board constraints, and software-support considerations described in the manufacturer datasheet.

Typical uses include industrial Ethernet gateways, factory automation controllers, embedded network appliances, video-network equipment, and compact access switches. The KSZ8794CNXCC is especially relevant when three copper endpoints need 10/100 Mb/s connectivity and a fourth port must provide a Gigabit path to a network processor or switching uplink.

Board design requires careful treatment of Ethernet magnetics, termination, supply routing, clocking, and high-speed uplink signals. Place the KSZ8794CNXCC and its decoupling close to the relevant connectors, follow the hardware design checklist for RJ45 termination, and preserve continuous ground references beneath high-speed interfaces.

This product summary consolidates the switch configuration, interface options, package information, drop-in-family alternatives, and implementation guidance needed to evaluate the KSZ8794CNXCC before beginning a Layer 2 Ethernet design.

Drop-in-Alternativen für KSZ8794CNXCC – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit KSZ8794CNXCC (gleiche Bauform und Footprint).

KSZ8794CNXIC

✅ Drop-In
Microchip Technology
📦 64-pin QFN (8x8 mm)
Layer 2 managed Ethernet switch · 3 ports · 10/100 Mbps · 1 port · 10/100/1000 Mbps · RGMII, MII, RMII · 10/100BASE-T/TX · Layer 2

Preis auf Anfrage

Datenblatt ansehen →

KSZ8795CNXCC

✅ Drop-In
📦 64-pin QFN (8x8 mm)
The family variant adds Ethernet and QoS-related features while retaining a 64-QFN package; interface and register differences require verification before substitution

📋 Referenzalternative (nicht im Katalog)

KSZ8794CNXCC Grenzwerte & elektrische Eigenschaften

Product Type Layer 2 managed Ethernet switch
Number of Ports 4 ports
Copper Port Configuration 3 ports at 10/100 Mb/s and 1 Gigabit uplink at 10/100/1000 Mb/s
Uplink Interface Gigabit RGMII/MII/RMII
Supported Host Interfaces RGMII, MII, and RMII
Ethernet Standard 10/100 Base-T/TX
Uplink Ethernet Rate 10/100/1000 Mb/s
Versorgungsspannung 3.3 V
Package Type 64-pin QFN
Package Dimensions 8 mm x 8 mm
Montageart Surface mount
Packaging Form Tray
Internal Biasing Integrated
On-Chip Termination Integrated
Managed Layer Layer 2

KSZ8794CNXCC 8 mm x 8 mm Pinbelegungsleitfaden

Pinbelegung für KSZ8794CNXCC (8 mm x 8 mm-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für KSZ8794CNXCC im 8 mm x 8 mm-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für KSZ8794CNXCC.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

KSZ8794CNXCC ist geeignet für 6 Anwendungs: Industrial Ethernet Gateway, Factory Automation Controller, Embedded Network Appliance, Video Network Equipment, Compact Access Switch, Communication Equipment.

🏭

Industrial Ethernet Gateway

The KSZ8794CNXCC fits an industrial gateway that connects three 10/100 Mb/s local devices to a Gigabit network backbone. The managed Layer 2 switch provides controlled frame forwarding while the fourth port reaches a higher-speed network through RGMII, MII, or RMII. Operating from 3.3 V and using a compact 64-QFN, 8 mm by 8 mm package helps reduce board area in DIN-rail or embedded gateway products. The design should allocate copper, magnetics, and RJ45 protection according to Microchip’s hardware design checklist, particularly the 75-ohm, 1000 pF, 2 kV center-tap network.

🏭

Factory Automation Controller

The KSZ8794CNXCC can serve as the central Ethernet switch in a factory automation controller with three 10/100 Mb/s machine interfaces and one Gigabit uplink. Its managed Layer 2 operation is useful when the controller must forward frames between local equipment while maintaining a defined path to a supervisory network. The 3.3 V supply requirement and integrated copper PHYs reduce the external circuitry needed for a multiport design. Layout must preserve high-speed uplink routing, provide local decoupling, and maintain controlled chassis-return paths around every Ethernet transformer.

🖥️

Embedded Network Appliance

The KSZ8794CNXCC is appropriate for an embedded appliance that exposes several low-speed service ports and a faster backbone connection. Three 10/100 Mb/s copper ports can serve management, status, or peripheral connections, while the 10/100/1000 Mb/s uplink links the appliance to a host processor over RGMII, MII, or RMII. Its integrated four-port architecture replaces a collection of discrete Ethernet interface blocks. Selection of the host interface should account for PCB area, processor support, timing, and software initialization requirements.

🎥

Video Network Equipment

The KSZ8794CNXCC can support video-network equipment that combines several 10/100 Mb/s management or sensor links with a Gigabit uplink. The three access ports provide economical connectivity for cameras, control panels, or monitoring nodes, while the Gigabit port carries consolidated traffic toward recording or aggregation equipment. The managed Layer 2 function gives the system a controlled forwarding architecture rather than shared collision-domain behavior. Ethernet magnetics, surge protection, and isolation must be selected to match the installation environment and EMC objectives.

🌐

Compact Access Switch

The KSZ8794CNXCC can form the core of a compact managed access switch with three 10/100 Mb/s endpoint ports and one Gigabit network port. This mixed-speed configuration is useful where field devices remain on 10/100 Mb/s while aggregation equipment requires 1 Gb/s. RGMII provides a high-throughput parallel host connection, whereas RMII can reduce host-side pin count when its timing and throughput requirements are acceptable. Firmware configuration should establish the desired forwarding, filtering, and management behavior without exceeding port or host-interface timing limits.

🌐

Communication Equipment

The KSZ8794CNXCC is suitable for communication equipment requiring a small number of copper Ethernet service ports and a Gigabit uplink to a network processor. Its three 10/100 Mb/s ports can connect management, configuration, or auxiliary equipment, while RGMII, MII, or RMII provides integration flexibility with different host architectures. The 64-QFN, 8 mm by 8 mm package supports compact boards, although careful fanout and exposed-pad layout remain essential. Signal-integrity review should cover uplink clocks, impedance-controlled traces, and return paths between the switch and magnetics.

What is the KSZ8794CNXCC?
The KSZ8794CNXCC is a Microchip Technology Layer 2 managed Ethernet switch with four copper ports, three operating at 10/100 Mb/s and one providing a 10/100/1000 Mb/s Gigabit uplink. According to the Microchip KSZ8794 product page, the device is a highly integrated four-port switch intended to reduce system cost. It is packaged in a 64-pin, 8 mm by 8 mm QFN and provides RGMII, MII, and RMII uplink options.
How many Ethernet ports does the KSZ8794CNXCC provide?
The KSZ8794CNXCC provides four integrated copper Ethernet ports in total. Three are 10/100 Mb/s access ports, while the fourth is a 10/100/1000 Mb/s Gigabit uplink, as described by Microchip for the KSZ8794 family. This arrangement allows several 10/100 Mb/s endpoints to reach a higher-speed backbone through one uplink, making the switch suitable for compact industrial and embedded gateways.
Which host interfaces are supported by the KSZ8794CNXCC?
The KSZ8794CNXCC supports RGMII, MII, and RMII for its Gigabit uplink. Microchip identifies the device as an integrated four-port 10/100 managed Ethernet switch with a Gigabit RGMII/MII/RMII interface. RGMII is appropriate for a full parallel Gigabit interface, while RMII uses fewer host signals and MII is a legacy parallel option. Interface selection should follow the host processor and required signaling rate.
Where can I download the KSZ8794CNXCC datasheet PDF?
The official KSZ8794CNXCC datasheet PDF is available from Microchip at the KSZ8794CNX product document link shown on this page. The document is titled “Integrated 4-Port 10/100 Managed Ethernet Switch with Gigabit RGMII/MII/RMII Interface” and carries document identifier DS00002134B. It is the primary source for electrical characteristics, register definitions, timing, package dimensions, and application guidance.
Where can I find the KSZ8794CNXCC pinout?
The KSZ8794CNXCC pinout is contained in the pin-description and package-drawing sections of the official Microchip KSZ8794CNX datasheet. The device uses a 64-pin QFN package, including its exposed thermal and electrical connection requirements. Use the manufacturer’s ordered pin table when assigning PCB nets, and consult the hardware design checklist for implementation details that complement the electrical datasheet.
What package and supply voltage does the KSZ8794CNXCC use?
The KSZ8794CNXCC uses a 3.3 V supply and is offered in a 64-pin QFN package measuring 8 mm by 8 mm. The package is intended for surface-mount assembly and is listed in tray packaging for the base ordering code. Exact pin functions, exposed-pad connection, absolute maximum ratings, and recommended operating limits should be taken from the manufacturer datasheet and hardware design checklist.
What is the difference between KSZ8794CNXCC and KSZ8794CNXIC?
KSZ8794CNXCC and KSZ8794CNXIC are ordering variants associated with the same KSZ8794CNX switch family. Published comparison information identifies both as the 64-pin managed Ethernet-switch solution, while the suffix denotes ordering or packaging conditions rather than a change in the core four-port architecture. Confirm the exact temperature grade, package form, and marking against the ordering table in the Microchip datasheet before substitution.
Is the KSZ8795CNXCC a drop-in replacement for KSZ8794CNXCC?
The KSZ8795CNXCC is a closely related managed-switch option, but it should not be treated as an automatic drop-in replacement without pin-level review. Cross-reference information describes the KSZ8795CNXCC as having additional capabilities, including advanced Ethernet support, while both devices appear in the same 64-QFN family. Verify pin assignments, host-interface compatibility, register behavior, thermal requirements, and software initialization before production substitution.
When should I choose the KSZ8794CNXCC over another Ethernet switch?
Choose the KSZ8794CNXCC when a design needs three 10/100 Mb/s copper access ports, one Gigabit uplink, managed Layer 2 behavior, and a single 64-QFN device. Its RGMII, MII, and RMII choices provide flexibility across different host processors. Consider another switch family when a design requires more copper ports, all-Gigabit access ports, different management features, or an interface not present in the KSZ8794.
Is the KSZ8794CNXCC suitable for industrial equipment?
The KSZ8794CNXCC is functionally suitable for industrial controllers, gateways, and automation equipment that require three 10/100 Mb/s copper ports and a Gigabit uplink. Its managed Layer 2 feature set and integrated PHYs can simplify network implementation. Final qualification still requires checking the specified temperature grade, power behavior, isolation strategy, EMC requirements, and environmental targets for the finished equipment.
How should Ethernet termination be implemented around the KSZ8794CNXCC?
Follow Microchip’s KSZ8794CNX hardware design checklist for connector and termination layout. The checklist specifies that RJ45 pin 3 connects to TX+ and pin 6 to TX−, while the transmit-side center tap uses a 75-ohm resistor through a 1000 pF, 2 kV capacitor to chassis ground. Preserve that controlled return path and keep the switch, magnetics, and protection components arranged to minimize differential-pair disruption.
How much power does the KSZ8794CNXCC consume?
The KSZ8794CNXCC power consumption depends on operating configuration, port activity, interface mode, supply voltage, and thermal conditions. Microchip describes the family as incorporating internal biasing and low-power design, but a single maximum-power value cannot be safely assigned without the operating-mode table from the manufacturer datasheet. Use the worst-case port and interface scenario when sizing the local supply and copper area.
Where can I buy KSZ8794CNXCC and what is its lead time?
Use the Request a Quote form on this page to request current KSZ8794CNXCC availability, MOQ, lead time, and a quotation. The form allows the request to be matched to the exact ordering code, package form, and required quantity. Lifecycle and supply conditions should be confirmed at quotation time because production and distribution schedules can change independently of the technical design.
What is the current price of KSZ8794CNXCC?
The current commercial price for KSZ8794CNXCC is obtained through the Request a Quote form on this page. The request should identify the exact base ordering code, 64-QFN package, tray packaging, and required production quantity so the quotation reflects the correct configuration. The form is also the appropriate route for requesting volume breaks and a scheduled delivery commitment.
What are the key specifications engineers should know about KSZ8794CNXCC?
The key engineering specifications are four integrated copper ports, three 10/100 Mb/s access ports, one 10/100/1000 Mb/s uplink, and support for RGMII, MII, and RMII. Microchip identifies the KSZ8794 as a managed Layer 2 switch and the part as a 64-QFN device measuring 8 mm by 8 mm. Its 3.3 V operation, internal biasing, and integrated termination simplify Ethernet hardware design.

Technische Referenzdaten für KSZ8794CNXCC – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the KSZ8794CNXCC when the equipment needs exactly three 10/100 Mb/s copper access ports, one Gigabit uplink, managed Layer 2 operation, and a 3.3 V supply in a compact 64-QFN design. It is especially suitable when the host processor supports RGMII, MII, or RMII and the product needs a managed access-switch function rather than independent PHY-only ports. KSZ8794CNXIC is the closest same-family ordering option when its specified temperature grade and packaging match the production requirement. Consider KSZ8795CNXCC when its additional Ethernet and QoS capabilities provide a functional benefit, but validate pin, register, and firmware compatibility before using it as a substitution. For requirements involving more than four ports, all-Gigabit copper access ports, or a different management architecture, evaluate another switch family because footprint compatibility alone does not meet the application requirement.

Vergleich mit Alternativen

Parameter Dieses Produkt KSZ8794CNXIC KSZ8795CNXCC
Brand Microchip Technology Microchip Technology Microchip Technology
Package 64-pin QFN (8x8 mm) 64-pin QFN (8x8 mm) 64-pin QFN (8x8 mm)
Product Type Layer 2 managed Ethernet switch Layer 2 managed Ethernet switch Managed Ethernet switch
Uplink Rate 10/100/1000 Mb/s 10/100/1000 Mb/s Gigabit Ethernet support
Integrated Features Internal biasing and on-chip termination Internal biasing and on-chip termination Additional Ethernet and advanced QoS-related features

Wichtigste Unterscheidungsmerkmale

  • Mixed-speed four-port integration (vs. KSZ8795CNXCC)
  • Multiple host-interface choices (vs. KSZ8794CNXIC)
  • Integration for compact Ethernet designs (vs. KSZ8795CNXCC)

Designhinweise

Follow the Microchip KSZ8794CNX hardware design checklist when placing the switch, Ethernet magnetics, and protection components. The specified RJ45 transmit path connects pin 3 to TX+ and pin 6 to TX−, with the cable-side center tap terminated through a 75-ohm resistor and a 1000 pF, 2 kV capacitor to chassis ground. Preserve this controlled connection and avoid long unprotected copper stubs near the connector.

Place the KSZ8794CNXCC close to the Ethernet magnetics and place all decoupling capacitors adjacent to their assigned supply and ground pins. Route RGMII, MII, or RMII signals over continuous reference planes with short point-to-point connections. Keep switching and clock sources away from copper-port traces, and verify the exposed-pad connection and via arrangement against the package drawing in the manufacturer datasheet.

Size the 3.3 V supply path for the worst combination of active ports, uplink mode, and temperature. Use local bulk and high-frequency decoupling as specified in the manufacturer application guidance, and provide low-impedance planes from the source to the switch. Since the device integrates biasing and termination, verify supply startup and current limits in the same operating modes used by the final network equipment.

Do not assume that a 64-pin QFN family member is automatically interchangeable. Before substituting KSZ8794CNXIC or KSZ8795CNXCC, compare the ordered pin table, exposed-pad requirements, temperature grade, host-interface timing, register definitions, and startup behavior. A footprint match alone does not guarantee software compatibility or identical management features, so qualify the complete Ethernet interface rather than only the physical package.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The Ethernet switch interface is not an automotive-qualified component classification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code and package form.

Ähnliche Suchanfragen

KSZ8794CNXCC datasheet KSZ8794CNXCC datasheet pdf KSZ8794CNXCC pinout KSZ8794CNXCC specifications KSZ8794CNXCC equivalent KSZ8794CNXCC replacement KSZ8794CNXCC price KSZ8794CNXCC stock Microchip KSZ8794CNXCC KSZ8794CNXCC QFN-64 KSZ8794CNXCC Ethernet switch KSZ8794CNXCC vs KSZ8795CNXCC KSZ8794CNXCC application circuit KSZ8794CNXCC hardware design checklist

Verwandte Bauteile & Begriffe

Microchip Technology KSZ8794CNXCC KSZ8794CNXIC KSZ8795CNXCC KSZ8794 managed Ethernet switch Layer 2 switch Ethernet switch Ethernet interface IC 10/100 Base-T/TX PHY Gigabit Ethernet RGMII MII RMII 64-pin QFN QFN-64 8 mm by 8 mm QFN surface mount internal biasing on-chip termination industrial Ethernet factory automation network gateway 3.3 V Ethernet magnetics RJ45 Microchip hardware design checklist
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen