KSZ8794CNXCC - 4-Port 10/100 Managed Ethernet Switch | Microchip
料号: KSZ8794CNXCC ✓ 量产中KSZ8794CNXCC 概述
An Ethernet switch is a Layer 2 network component that receives Ethernet frames, examines destination addresses, and forwards traffic through the appropriate physical port. The KSZ8794CNXCC belongs to the managed-switch hierarchy, combining integrated 10/100 Base-T/TX PHYs with management features designed to reduce the component count and board area required for multiport industrial or embedded Ethernet equipment.
The principal features are four integrated copper Ethernet ports, a configurable Gigabit uplink, support for RGMII, MII, and RMII host interfaces, internal biasing, and on-chip termination. Its 8 mm by 8 mm QFN-64 package supports compact designs while exposing high-speed network connectivity without requiring four discrete Ethernet PHYs. The managed Layer 2 architecture is suitable for systems that need controlled forwarding behavior rather than only basic hub functionality.
The uplink architecture allows a lower-cost 10/100 Mb/s access network to connect to a faster Gigabit backbone through a single high-speed host interface. RGMII supports parallel high-speed signaling, MII is a lower-speed parallel interface, and RMII reduces the number of host-side signals. Designers should select the interface according to the host processor, signal-rate requirements, board constraints, and software-support considerations described in the manufacturer datasheet.
Typical uses include industrial Ethernet gateways, factory automation controllers, embedded network appliances, video-network equipment, and compact access switches. The KSZ8794CNXCC is especially relevant when three copper endpoints need 10/100 Mb/s connectivity and a fourth port must provide a Gigabit path to a network processor or switching uplink.
Board design requires careful treatment of Ethernet magnetics, termination, supply routing, clocking, and high-speed uplink signals. Place the KSZ8794CNXCC and its decoupling close to the relevant connectors, follow the hardware design checklist for RJ45 termination, and preserve continuous ground references beneath high-speed interfaces.
This product summary consolidates the switch configuration, interface options, package information, drop-in-family alternatives, and implementation guidance needed to evaluate the KSZ8794CNXCC before beginning a Layer 2 Ethernet design.
直接替换替代料: KSZ8794CNXCC ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: KSZ8794CNXCC (相同外形与封装尺寸).
KSZ8794CNXIC
✅ 直接替换联系询价
查看数据手册 →KSZ8795CNXCC
✅ 直接替换📋 参考替代料(不在目录中)
KSZ8794CNXCC 最大额定值与电气特性
| Product Type | Layer 2 managed Ethernet switch |
| Number of Ports | 4 ports |
| Copper Port Configuration | 3 ports at 10/100 Mb/s and 1 Gigabit uplink at 10/100/1000 Mb/s |
| Uplink Interface | Gigabit RGMII/MII/RMII |
| Supported Host Interfaces | RGMII, MII, and RMII |
| Ethernet Standard | 10/100 Base-T/TX |
| Uplink Ethernet Rate | 10/100/1000 Mb/s |
| 电源电压 | 3.3 V |
| Package Type | 64-pin QFN |
| Package Dimensions | 8 mm x 8 mm |
| 安装类型 | Surface mount |
| Packaging Form | Tray |
| Internal Biasing | Integrated |
| On-Chip Termination | Integrated |
| Managed Layer | Layer 2 |
KSZ8794CNXCC 8 mm x 8 mm 引脚配置指南
KSZ8794CNXCC(8 mm x 8 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: KSZ8794CNXCC.
请参阅 数据手册 以查看完整引脚配置。
典型应用
KSZ8794CNXCC 适用于 6 应用s: Industrial Ethernet Gateway, Factory Automation Controller, Embedded Network Appliance, Video Network Equipment, Compact Access Switch, Communication Equipment.
Industrial Ethernet Gateway
The KSZ8794CNXCC fits an industrial gateway that connects three 10/100 Mb/s local devices to a Gigabit network backbone. The managed Layer 2 switch provides controlled frame forwarding while the fourth port reaches a higher-speed network through RGMII, MII, or RMII. Operating from 3.3 V and using a compact 64-QFN, 8 mm by 8 mm package helps reduce board area in DIN-rail or embedded gateway products. The design should allocate copper, magnetics, and RJ45 protection according to Microchip’s hardware design checklist, particularly the 75-ohm, 1000 pF, 2 kV center-tap network.
推荐
Factory Automation Controller
The KSZ8794CNXCC can serve as the central Ethernet switch in a factory automation controller with three 10/100 Mb/s machine interfaces and one Gigabit uplink. Its managed Layer 2 operation is useful when the controller must forward frames between local equipment while maintaining a defined path to a supervisory network. The 3.3 V supply requirement and integrated copper PHYs reduce the external circuitry needed for a multiport design. Layout must preserve high-speed uplink routing, provide local decoupling, and maintain controlled chassis-return paths around every Ethernet transformer.
推荐
Embedded Network Appliance
The KSZ8794CNXCC is appropriate for an embedded appliance that exposes several low-speed service ports and a faster backbone connection. Three 10/100 Mb/s copper ports can serve management, status, or peripheral connections, while the 10/100/1000 Mb/s uplink links the appliance to a host processor over RGMII, MII, or RMII. Its integrated four-port architecture replaces a collection of discrete Ethernet interface blocks. Selection of the host interface should account for PCB area, processor support, timing, and software initialization requirements.
推荐
Video Network Equipment
The KSZ8794CNXCC can support video-network equipment that combines several 10/100 Mb/s management or sensor links with a Gigabit uplink. The three access ports provide economical connectivity for cameras, control panels, or monitoring nodes, while the Gigabit port carries consolidated traffic toward recording or aggregation equipment. The managed Layer 2 function gives the system a controlled forwarding architecture rather than shared collision-domain behavior. Ethernet magnetics, surge protection, and isolation must be selected to match the installation environment and EMC objectives.
推荐
Compact Access Switch
The KSZ8794CNXCC can form the core of a compact managed access switch with three 10/100 Mb/s endpoint ports and one Gigabit network port. This mixed-speed configuration is useful where field devices remain on 10/100 Mb/s while aggregation equipment requires 1 Gb/s. RGMII provides a high-throughput parallel host connection, whereas RMII can reduce host-side pin count when its timing and throughput requirements are acceptable. Firmware configuration should establish the desired forwarding, filtering, and management behavior without exceeding port or host-interface timing limits.
推荐
Communication Equipment
The KSZ8794CNXCC is suitable for communication equipment requiring a small number of copper Ethernet service ports and a Gigabit uplink to a network processor. Its three 10/100 Mb/s ports can connect management, configuration, or auxiliary equipment, while RGMII, MII, or RMII provides integration flexibility with different host architectures. The 64-QFN, 8 mm by 8 mm package supports compact boards, although careful fanout and exposed-pad layout remain essential. Signal-integrity review should cover uplink clocks, impedance-controlled traces, and return paths between the switch and magnetics.
推荐
推荐产品汇总
工程参考数据: KSZ8794CNXCC ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | KSZ8794CNXIC | KSZ8795CNXCC |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin QFN (8x8 mm) | 64-pin QFN (8x8 mm) | 64-pin QFN (8x8 mm) |
| Product Type | Layer 2 managed Ethernet switch | Layer 2 managed Ethernet switch | Managed Ethernet switch |
| Uplink Rate | 10/100/1000 Mb/s | 10/100/1000 Mb/s | Gigabit Ethernet support |
| Integrated Features | Internal biasing and on-chip termination | Internal biasing and on-chip termination | Additional Ethernet and advanced QoS-related features |
关键差异点
- Mixed-speed four-port integration (对比 KSZ8795CNXCC)
- Multiple host-interface choices (对比 KSZ8794CNXIC)
- Integration for compact Ethernet designs (对比 KSZ8795CNXCC)
设计说明
Follow the Microchip KSZ8794CNX hardware design checklist when placing the switch, Ethernet magnetics, and protection components. The specified RJ45 transmit path connects pin 3 to TX+ and pin 6 to TX−, with the cable-side center tap terminated through a 75-ohm resistor and a 1000 pF, 2 kV capacitor to chassis ground. Preserve this controlled connection and avoid long unprotected copper stubs near the connector.
Place the KSZ8794CNXCC close to the Ethernet magnetics and place all decoupling capacitors adjacent to their assigned supply and ground pins. Route RGMII, MII, or RMII signals over continuous reference planes with short point-to-point connections. Keep switching and clock sources away from copper-port traces, and verify the exposed-pad connection and via arrangement against the package drawing in the manufacturer datasheet.
Size the 3.3 V supply path for the worst combination of active ports, uplink mode, and temperature. Use local bulk and high-frequency decoupling as specified in the manufacturer application guidance, and provide low-impedance planes from the source to the switch. Since the device integrates biasing and termination, verify supply startup and current limits in the same operating modes used by the final network equipment.
Do not assume that a 64-pin QFN family member is automatically interchangeable. Before substituting KSZ8794CNXIC or KSZ8795CNXCC, compare the ordered pin table, exposed-pad requirements, temperature grade, host-interface timing, register definitions, and startup behavior. A footprint match alone does not guarantee software compatibility or identical management features, so qualify the complete Ethernet interface rather than only the physical package.
合规信息
The Ethernet switch interface is not an automotive-qualified component classification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code and package form.