KSZ8794CNXCC - 4-Port 10/100 Managed Ethernet Switch | Microchip
MPN: KSZ8794CNXCC ✓ פעילKSZ8794CNXCC סקירה
An Ethernet switch is a Layer 2 network component that receives Ethernet frames, examines destination addresses, and forwards traffic through the appropriate physical port. The KSZ8794CNXCC belongs to the managed-switch hierarchy, combining integrated 10/100 Base-T/TX PHYs with management features designed to reduce the component count and board area required for multiport industrial or embedded Ethernet equipment.
The principal features are four integrated copper Ethernet ports, a configurable Gigabit uplink, support for RGMII, MII, and RMII host interfaces, internal biasing, and on-chip termination. Its 8 mm by 8 mm QFN-64 package supports compact designs while exposing high-speed network connectivity without requiring four discrete Ethernet PHYs. The managed Layer 2 architecture is suitable for systems that need controlled forwarding behavior rather than only basic hub functionality.
The uplink architecture allows a lower-cost 10/100 Mb/s access network to connect to a faster Gigabit backbone through a single high-speed host interface. RGMII supports parallel high-speed signaling, MII is a lower-speed parallel interface, and RMII reduces the number of host-side signals. Designers should select the interface according to the host processor, signal-rate requirements, board constraints, and software-support considerations described in the manufacturer datasheet.
Typical uses include industrial Ethernet gateways, factory automation controllers, embedded network appliances, video-network equipment, and compact access switches. The KSZ8794CNXCC is especially relevant when three copper endpoints need 10/100 Mb/s connectivity and a fourth port must provide a Gigabit path to a network processor or switching uplink.
Board design requires careful treatment of Ethernet magnetics, termination, supply routing, clocking, and high-speed uplink signals. Place the KSZ8794CNXCC and its decoupling close to the relevant connectors, follow the hardware design checklist for RJ45 termination, and preserve continuous ground references beneath high-speed interfaces.
This product summary consolidates the switch configuration, interface options, package information, drop-in-family alternatives, and implementation guidance needed to evaluate the KSZ8794CNXCC before beginning a Layer 2 Ethernet design.
חלופות תחליף ישיר עבור KSZ8794CNXCC — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם KSZ8794CNXCC (אותו גורם צורה וטביעת רגל).
KSZ8794CNXIC
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←KSZ8795CNXCC
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
KSZ8794CNXCC דירוגים מרביים ומאפיינים חשמליים
| Product Type | Layer 2 managed Ethernet switch |
| Number of Ports | 4 ports |
| Copper Port Configuration | 3 ports at 10/100 Mb/s and 1 Gigabit uplink at 10/100/1000 Mb/s |
| Uplink Interface | Gigabit RGMII/MII/RMII |
| Supported Host Interfaces | RGMII, MII, and RMII |
| Ethernet Standard | 10/100 Base-T/TX |
| Uplink Ethernet Rate | 10/100/1000 Mb/s |
| מתח אספקה | 3.3 V |
| Package Type | 64-pin QFN |
| Package Dimensions | 8 mm x 8 mm |
| סוג הרכבה | Surface mount |
| Packaging Form | Tray |
| Internal Biasing | Integrated |
| On-Chip Termination | Integrated |
| Managed Layer | Layer 2 |
מדריך תצורת פינים של KSZ8794CNXCC 8 mm x 8 mm
תצורת פינים עבור KSZ8794CNXCC (מארזת 8 mm x 8 mm). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור KSZ8794CNXCC.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
KSZ8794CNXCC מתאים עבור 6 יישוםs: Industrial Ethernet Gateway, Factory Automation Controller, Embedded Network Appliance, Video Network Equipment, Compact Access Switch, Communication Equipment.
Industrial Ethernet Gateway
The KSZ8794CNXCC fits an industrial gateway that connects three 10/100 Mb/s local devices to a Gigabit network backbone. The managed Layer 2 switch provides controlled frame forwarding while the fourth port reaches a higher-speed network through RGMII, MII, or RMII. Operating from 3.3 V and using a compact 64-QFN, 8 mm by 8 mm package helps reduce board area in DIN-rail or embedded gateway products. The design should allocate copper, magnetics, and RJ45 protection according to Microchip’s hardware design checklist, particularly the 75-ohm, 1000 pF, 2 kV center-tap network.
מומלץ
Factory Automation Controller
The KSZ8794CNXCC can serve as the central Ethernet switch in a factory automation controller with three 10/100 Mb/s machine interfaces and one Gigabit uplink. Its managed Layer 2 operation is useful when the controller must forward frames between local equipment while maintaining a defined path to a supervisory network. The 3.3 V supply requirement and integrated copper PHYs reduce the external circuitry needed for a multiport design. Layout must preserve high-speed uplink routing, provide local decoupling, and maintain controlled chassis-return paths around every Ethernet transformer.
מומלץ
Embedded Network Appliance
The KSZ8794CNXCC is appropriate for an embedded appliance that exposes several low-speed service ports and a faster backbone connection. Three 10/100 Mb/s copper ports can serve management, status, or peripheral connections, while the 10/100/1000 Mb/s uplink links the appliance to a host processor over RGMII, MII, or RMII. Its integrated four-port architecture replaces a collection of discrete Ethernet interface blocks. Selection of the host interface should account for PCB area, processor support, timing, and software initialization requirements.
מומלץ
Video Network Equipment
The KSZ8794CNXCC can support video-network equipment that combines several 10/100 Mb/s management or sensor links with a Gigabit uplink. The three access ports provide economical connectivity for cameras, control panels, or monitoring nodes, while the Gigabit port carries consolidated traffic toward recording or aggregation equipment. The managed Layer 2 function gives the system a controlled forwarding architecture rather than shared collision-domain behavior. Ethernet magnetics, surge protection, and isolation must be selected to match the installation environment and EMC objectives.
מומלץ
Compact Access Switch
The KSZ8794CNXCC can form the core of a compact managed access switch with three 10/100 Mb/s endpoint ports and one Gigabit network port. This mixed-speed configuration is useful where field devices remain on 10/100 Mb/s while aggregation equipment requires 1 Gb/s. RGMII provides a high-throughput parallel host connection, whereas RMII can reduce host-side pin count when its timing and throughput requirements are acceptable. Firmware configuration should establish the desired forwarding, filtering, and management behavior without exceeding port or host-interface timing limits.
מומלץ
Communication Equipment
The KSZ8794CNXCC is suitable for communication equipment requiring a small number of copper Ethernet service ports and a Gigabit uplink to a network processor. Its three 10/100 Mb/s ports can connect management, configuration, or auxiliary equipment, while RGMII, MII, or RMII provides integration flexibility with different host architectures. The 64-QFN, 8 mm by 8 mm package supports compact boards, although careful fanout and exposed-pad layout remain essential. Signal-integrity review should cover uplink clocks, impedance-controlled traces, and return paths between the switch and magnetics.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור KSZ8794CNXCC — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | KSZ8794CNXIC | KSZ8795CNXCC |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin QFN (8x8 mm) | 64-pin QFN (8x8 mm) | 64-pin QFN (8x8 mm) |
| Product Type | Layer 2 managed Ethernet switch | Layer 2 managed Ethernet switch | Managed Ethernet switch |
| Uplink Rate | 10/100/1000 Mb/s | 10/100/1000 Mb/s | Gigabit Ethernet support |
| Integrated Features | Internal biasing and on-chip termination | Internal biasing and on-chip termination | Additional Ethernet and advanced QoS-related features |
מבדילים עיקריים
- Mixed-speed four-port integration (לעומתKSZ8795CNXCC)
- Multiple host-interface choices (לעומתKSZ8794CNXIC)
- Integration for compact Ethernet designs (לעומתKSZ8795CNXCC)
הערות תכנון
Follow the Microchip KSZ8794CNX hardware design checklist when placing the switch, Ethernet magnetics, and protection components. The specified RJ45 transmit path connects pin 3 to TX+ and pin 6 to TX−, with the cable-side center tap terminated through a 75-ohm resistor and a 1000 pF, 2 kV capacitor to chassis ground. Preserve this controlled connection and avoid long unprotected copper stubs near the connector.
Place the KSZ8794CNXCC close to the Ethernet magnetics and place all decoupling capacitors adjacent to their assigned supply and ground pins. Route RGMII, MII, or RMII signals over continuous reference planes with short point-to-point connections. Keep switching and clock sources away from copper-port traces, and verify the exposed-pad connection and via arrangement against the package drawing in the manufacturer datasheet.
Size the 3.3 V supply path for the worst combination of active ports, uplink mode, and temperature. Use local bulk and high-frequency decoupling as specified in the manufacturer application guidance, and provide low-impedance planes from the source to the switch. Since the device integrates biasing and termination, verify supply startup and current limits in the same operating modes used by the final network equipment.
Do not assume that a 64-pin QFN family member is automatically interchangeable. Before substituting KSZ8794CNXIC or KSZ8795CNXCC, compare the ordered pin table, exposed-pad requirements, temperature grade, host-interface timing, register definitions, and startup behavior. A footprint match alone does not guarantee software compatibility or identical management features, so qualify the complete Ethernet interface rather than only the physical package.
מידע על תאימות
The Ethernet switch interface is not an automotive-qualified component classification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code and package form.