LM2902WYPT - 1.3MHz Quad Op Amp | STMicroelectronics
Teilenummer: LM2902WYPT ✓ AktivLM2902WYPT Übersicht
An operational amplifier, or op amp, is a high-gain analog building block used to amplify voltage differences, buffer sensors, drive loads, and implement feedback-control loops. The LM2902 belongs to the broader operational amplifier hierarchy, where four internally compensated amplifiers are integrated into one package to reduce component count in industrial, automotive, and instrumentation systems. Its push-pull output stage supports a variety of low- and mid-frequency signal-conditioning applications.
Key electrical characteristics include a 1.3 MHz gain-bandwidth product, 100 dB large-signal voltage gain, 375 uA supply current per amplifier, 20 nA low input bias current, and 2 nA low input-offset current. The 800 V ESD protection rating helps improve handling robustness, while the wide supply range supports circuits operating from industrial control, test, measurement, and vehicle-related power systems.
The LM2902 architecture provides four independent high-gain amplifiers with internal frequency compensation. This simplifies PCB layout because external compensation networks are not required. The common-mode input range includes the negative supply rail, making the device useful in single-supply sensor interfaces where signals remain close to ground. The wide input bias-voltage range also supports bipolar input stages within the device.
Typical uses include four-channel sensor amplification, low-frequency active filtering, transducer interfacing, current monitoring, sample-and-hold signal conditioning, and general-purpose analog control. The device can also provide independent amplifier sections for comparators, waveform conditioners, and audio or communications interface circuits when the bandwidth and slew-rate requirements remain modest.
For layout, place input and feedback components close to their associated amplifier pins and keep sensitive input traces away from high-current switching paths. Because the LM2902 is intended primarily for low-frequency precision-oriented applications, verify bandwidth, output swing, load capability, noise, and input-offset requirements against the actual signal path. Stable feedback design is essential because the amplifiers are internally compensated.
This product page combines the manufacturer device information with practical engineering guidance for single- and dual-supply implementation, application analysis, package considerations, and drop-in replacement evaluation. It is intended to help engineers select the LM2902WYPT for general-purpose four-amplifier designs and to identify what must be checked before PCB-level substitution.
Drop-in-Alternativen für LM2902WYPT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM2902WYPT (gleiche Bauform und Footprint) – abweichend in Package, Gain-Bandwidth Product, Amplifier Type, Number of Amplifiers, Product Type.
LM2902YPT
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM2902PWRG3
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM2902WYPT Grenzwerte & elektrische Eigenschaften
| Amplifier Count | 4 amplifiers |
| Product Type | Low-power quad operational amplifier |
| Gain-Bandwidth Product | 1.3 MHz |
| Large-Signal Voltage Gain | 100 dB |
| Supply Current per Amplifier | 375 uA |
| Input Bias Current | 20 nA |
| Input Offset Current | 2 nA |
| ESD Protection | 800 V |
| Single-Supply Operating Range | Up to 30 V |
| Dual-Supply Operating Range | Up to ±15 V |
| Input Common-Mode Voltage Range | Includes the negative supply rail |
| Frequency Compensation | Internal |
| Output Stage | Push-pull |
| Gehäuse | 14-TSSOP |
| Package Width | 4.40 mm |
| Montageart | Surface mount |
LM2902WYPT 4.40 mm Pinbelegungsleitfaden
Pinbelegung für LM2902WYPT (4.40 mm-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für LM2902WYPT.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LM2902WYPT ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Automotive Control Circuit Amplification, Active Low-Frequency Filters, Current Monitoring and Control Loops, Test and Measurement Buffering, Audio and Communications Interface Circuits.
Industrial Sensor Signal Conditioning
The LM2902WYPT fits four-channel industrial sensor interfaces because it combines four independent amplifiers with an input common-mode range that includes the negative supply rail. This helps process signals from pressure, temperature, and position sensors that operate near ground. With a 1.3 MHz gain-bandwidth product and 375 uA supply current per amplifier, it provides useful bandwidth without imposing a high power budget. Use each section for gain, buffering, or active filtering, and verify input offset, output swing, noise, and operating-temperature requirements against the sensor interface.
Empfohlen
Automotive Control Circuit Amplification
The LM2902WYPT is suitable for automotive and industrial control circuits that need several low-frequency analog channels in one package. The STMicroelectronics device provides four internally compensated high-gain amplifiers, a 1.3 MHz gain-bandwidth product, and operation across single supplies up to 30 V. That combination supports conditioning of resistive, inductive, and voltage-based sensor signals while reducing board area. The circuit must remain within the verified supply and common-mode limits, and the automotive qualification status should be confirmed for each production order code.
Empfohlen
Active Low-Frequency Filters
The LM2902WYPT can implement several active-filter stages because it contains four independent, internally compensated amplifiers with a 1.3 MHz gain-bandwidth product. SECTIONS can form low-pass, high-pass, band-pass, or notch networks when component tolerances and closed-loop gain are selected carefully. The 375 uA supply current per amplifier is useful in compact multi-filter modules, while the push-pull output stage supports standard feedback configurations. Confirm slew rate, output-current capability, and stability margins before selecting component values for the intended signal bandwidth.
Empfohlen
Current Monitoring and Control Loops
The LM2902WYPT is appropriate for current-monitoring and slow feedback-control circuits that need several amplifier channels sharing one package. Its 100 dB large-signal voltage gain and 1.3 MHz gain-bandwidth product provide useful open-loop performance for gain-of-10 or lower analog stages, while internal frequency compensation avoids external compensation networks. The four channels can amplify a current-sense signal, condition a reference, compare a threshold, and buffer a control output. Verify the input offset current of 2 nA, output swing, and response time against the control-loop accuracy and stability requirements.
Empfohlen
Test and Measurement Buffering
The LM2902WYPT can provide active buffering, gain, and differential-to-single-ended stages in test and measurement equipment. Four independent channels reduce the number of amplifier packages needed when routing several low-frequency signals through a common analog section. Its 375 uA supply current per amplifier is suitable for compact portable or embedded test systems, and the negative-rail-inclusive common-mode input range supports circuits that reference ground. Before using it with high-accuracy or high-impedance probes, verify input bias current, offset voltage, input capacitance, and output settling requirements.
Empfohlen
Audio and Communications Interface Circuits
The LM2902WYPT can handle low-frequency audio and communications interface functions such as input buffering, active gain, impedance conversion, and channel mixing. Its 1.3 MHz gain-bandwidth product covers many voice-band and control-signal tasks, while the push-pull output stage supports common feedback networks. Four channels allow a compact implementation of a two-channel audio preamplifier plus auxiliary buffering or filtering functions. Audio designs should also check noise, output swing, slew rate, channel matching, and the system load, because bandwidth alone does not determine full signal quality.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM2902WYPT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM2902YPT | LM2902PW |
|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments |
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Amplifier Count | 4 amplifiers | 4 amplifiers | 4 amplifiers |
Wichtigste Unterscheidungsmerkmale
- Four integrated amplifier channels with internal compensation (vs. LM2902PW)
- Wide single- and dual-supply operating capability (vs. LM2902YPT)
- Ground-referenced input capability (vs. LM2902PW)
Designhinweise
Place each amplifier's input, feedback, and decoupling connections close to the associated TSSOP pins. Keep high-impedance input traces short, avoid routing them beneath digital or switching-current paths, and use a continuous ground plane. The LM2902 has four independent amplifier sections, so assign and route each channel consistently to prevent feedback from one signal path from coupling into another.
Do not assume that every LM2902 package variant is a mechanical replacement. The target uses a 14-TSSOP package, while other ordering codes in the family can use different lead styles or temperature options. Compare the manufacturer pin table, footprint dimensions, exposed-pad requirements, and ordering information before replacing a populated board. For new layouts, verify input offset, common-mode limits, output swing, and load drive under the actual supply voltage.
Decouple the supply pins locally with ceramic capacitance selected using the stability and transient-response requirements in the manufacturer datasheet. Estimated: four amplifiers operating at 375 uA each draw approximately 1.5 mA total, excluding the load currents driven through the output stages. This arithmetic estimate does not include input bias current, output-current demand, or supply ripple, so verify the regulator and capacitor design against the complete loaded circuit.
Compliance-Informationen
The device is designed for automotive and industrial control applications, but the exact orderable MPN's environmental declarations and AEC-Q100 qualification status were not stated. Request current compliance documentation when required.