MAX3243EEUI+T - 250kbps 3/5 RS-232 Transceiver | Analog Devices
Teilenummer: MAX3243EEUI+T ✓ AktivMAX3243EEUI+T Übersicht
An RS-232 transceiver is an interface IC that converts between digital logic-level signals and differential, bipolar RS-232 line signals. The MAX3243 belongs to the RS-232 interface hierarchy, combining line drivers, line receivers, charge-pump voltage conversion, and automatic power management in one package. It is used to connect UART, microcontroller, industrial-control, and data-processing systems to legacy serial ports through a ±15kV-protected communications interface.
Key features include a 3.0V to 5.5V operating supply, 250kbps maximum data rate, three RS-232 drivers, five RS-232 receivers, and low 1µA shutdown supply current. The ±15kV ESD protection improves robustness when cables are connected or disconnected near exposed equipment. AutoShutdown and AutoShutdown Plus operation reduce supply current when the connected system is inactive, while the always-active receiver allows monitoring even when the main supply has shut down.
The MAX3243E family uses an internal charge-pump circuit to generate the positive and negative voltages required by RS-232 transmitters. This architecture lets a 3.0V to 5.5V system communicate with conventional RS-232 equipment without a separate negative supply. The MAX3243EEUI+T is specified for a -40°C to +85°C temperature range and is packaged in a 28-pin TSSOP for surface-mount industrial and embedded equipment.
Typical applications include industrial serial consoles, instrumentation interfaces, point-of-sale equipment, telecom systems, embedded control modules, and peripheral connectivity. In each case, the transceiver provides the electrical conversion and signal protection needed between a low-voltage digital controller and an RS-232 port. Designers should verify the required baud rate, cable length, connector protection, supply sequencing, and charge-pump capacitor placement against the manufacturer’s recommended application circuit.
For a robust design, place the charge-pump and supply-bypass capacitors close to their associated pins, route the RS-232 driver outputs and receiver inputs away from sensitive digital signals, and provide appropriate chassis grounding at the connector. The integrated ±15kV ESD protection does not replace external surge and lightning protection for long or unprotected cables. This page also organizes package, replacement, and application guidance to support faster engineering selection.
Drop-in-Alternativen für MAX3243EEUI+T – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MAX3243EEUI+T (gleiche Bauform und Footprint) – abweichend in Product Type, ESD Protection, Number of Receivers, Supply Voltage Range, Interface Standard.
MAX3243EIPWR
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →ST3243EBTR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX3243EEUI+T Technische Daten
| Product Type | RS-232 transceiver |
| Supply Voltage Range | 3.0V to 5.5V |
| Maximum Data Rate | 250kbps |
| Driver Count | 3 drivers |
| Receiver Count | 5 receivers |
| Duplex Mode | Full duplex |
| ESD Protection | ±15kV |
| Shutdown Supply Current | 1µA |
| Power Management Feature | AutoShutdown |
| Betriebstemperaturbereich | -40°C to +85°C |
| Gehäuse | 28-pin TSSOP |
| Montageart | Surface mount |
| Supported Standards | EIA/TIA-232, V.28 and V.24 |
| RoHS-Status | RoHS compliant |
| Typical Application | UART-to-RS-232 interface |
MAX3243EEUI+T 28-pin tssop Pinbelegungsleitfaden
Pinbelegung für MAX3243EEUI+T (28-pin tssop-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für MAX3243EEUI+T.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MAX3243EEUI+T ist geeignet für 6 Anwendungs: Industrial Serial Console, Point-of-Sale Terminal, Instrumentation and Test Equipment, Embedded Data Acquisition Module, Telecom Network Equipment, Peripheral and Cable Connectivity.
Industrial Serial Console
The MAX3243EEUI+T fits an industrial serial console because its three drivers and five receivers support bidirectional RS-232 communication from a 3.0V to 5.5V embedded controller. The 250kbps maximum data rate provides ample margin for configuration, logging, and diagnostic traffic. Its -40°C to +85°C range is suitable for many industrial environments, while ±15kV ESD protection improves resilience during routine cable connection. The always-active receiver can also monitor a remote line while AutoShutdown reduces power. Designers should still add external surge protection when a console cable exits the enclosure or connects to unprotected industrial cabling.
Empfohlen
Point-of-Sale Terminal
A point-of-sale terminal can use the MAX3243EEUI+T to bridge a low-voltage UART controller to an RS-232 peripheral such as a printer, scanner, or customer display. The 3.0V to 5.5V supply range supports both 3.3V and 5V logic systems, and three transmitter channels allow several serial accessories to share a multi-drop wiring arrangement when the system design permits it. The 250kbps capability is substantially faster than common peripheral baud rates. AutoShutdown helps control idle-system consumption, and the integrated ±15kV protection provides useful margin for cables handled by store personnel.
Empfohlen
Instrumentation and Test Equipment
The MAX3243EEUI+T is appropriate for legacy test and measurement equipment that still uses an RS-232 command or measurement port. Its 3-driver/5-receiver organization supports a control channel plus multiple monitoring inputs, while the 250kbps rate supports command throughput and moderate data logging. The always-active receiver is valuable when an instrument must observe a signal even while the main transceiver has entered AutoShutdown. Because laboratory and industrial cables can carry large external transients, the integrated ±15kV ESD rating should be complemented by suitable connector protection and a defined chassis-ground strategy.
Empfohlen
Embedded Data Acquisition Module
The MAX3243EEUI+T can connect an embedded acquisition module to legacy RS-232 sensors, programmers, or service equipment. The device accepts a 3.0V to 5.5V supply, allowing operation from common embedded rails, and its 250kbps data rate is suitable for many command-oriented acquisition protocols. Five receivers provide additional monitoring paths for status and interlock signals. AutoShutdown is valuable in battery- or power-constrained portable systems because the supply current can fall to approximately 1µA when no valid activity is detected. Firmware should account for wake-up latency and ensure that required monitoring receivers remain active where appropriate.
Empfohlen
Telecom Network Equipment
The MAX3243EEUI+T is suitable for service and configuration interfaces within telecom equipment that retains RS-232 connectivity. Its three drivers and five receivers can support equipment-control and monitoring functions, while the 250kbps rate is adequate for administrative commands and low-bandwidth diagnostics. The -40°C to +85°C operating range covers many outdoor and indoor telecom installations. AutoShutdown helps control consumption when management ports are idle, and ±15kV ESD protection strengthens the interface against nearby charged cables. Equipment exposed to lightning or severe industrial transients still requires coordinated surge protection, bonding, and grounding.
Empfohlen
Peripheral and Cable Connectivity
The MAX3243EEUI+T provides robust logic-to-RS-232 conversion for peripherals connected by short or medium-length shielded cables. Its 250kbps capability supports printers, scanners, programming equipment, and legacy control modules without requiring a separate negative supply. The ±15kV ESD protection is particularly useful for user-accessible connectors because it increases tolerance to electrostatic discharge during installation and servicing. Automatic shutdown reduces board-level standby demand, while the always-active receiver supports monitoring functions that must remain available. The PCB design should preserve the manufacturer’s charge-pump capacitor layout and keep transceiver routing away from sensitive analog or high-speed digital paths.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX3243EEUI+T – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX3243EIPWR | ST3243EBTR |
|---|---|---|---|
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Brand | Analog Devices | Texas Instruments | STMicroelectronics |
| Transceiver Configuration | 3 drivers, 5 receivers | 3 drivers, 5 receivers | 3 drivers, 5 receivers |
Wichtigste Unterscheidungsmerkmale
- Higher channel count than a basic RS-232 interface (vs. MAX232EIPWR)
- Always-active monitoring receiver (vs. ST3243EBTR)
- Defined extended-temperature operating range (vs. MAX3243EIPWR)
Designhinweise
Follow the MAX3243E recommended layout for the charge-pump capacitors and supply bypass components. Keep these components close to their associated device pins, use short return paths, and place the bypass capacitor where its ground connection joins the main ground plane. The exact capacitor values and PCB dimensions must be taken from the manufacturer application circuit because changing the charge-pump layout can affect startup, ringing, and transmitter output behavior.
Separate RS-232 driver outputs and receiver inputs from clocks, sensors, ADC signals, and other low-level analog paths. Driver edges can couple into nearby traces even though the interface uses a differential bipolar protocol at its external pins. Route the cable-side nets directly toward the connector or protection device, maintain the recommended spacing from unprotected board edges, and provide a low-impedance chassis-ground connection at the equipment entry point.
Do not treat the integrated ±15kV ESD rating as complete lightning or industrial surge protection. Long external cables can present transients beyond the interface’s ESD withstand rating, so use appropriately rated protection when the cable leaves the enclosure. Also confirm the connector shield and chassis-ground strategy because incorrectly routing surge current through the logic ground can damage surrounding equipment.
Account for AutoShutdown timing in the host firmware. The device can reduce shutdown supply current to approximately 1µA, but waking, charge-pump startup, and receiver qualification add latency before communication is reliable. Keep an always-active receiver path when the system must monitor a remote RS-232 line during low-power operation, and validate the complete wake-up sequence across temperature and supply-voltage corners.
Compliance-Informationen
The product listing identifies MAX3243EEUI+T as RoHS compliant. Reach, AEC-Q100, lead-free, halogen-free, and conflict-minerals status are not established by the cited product information and remain unknown.