MAX3243EEUI+T - 250kbps 3/5 RS-232 Transceiver | Analog Devices
MPN: MAX3243EEUI+T ✓ 啟用中MAX3243EEUI+T 概覽
An RS-232 transceiver is an interface IC that converts between digital logic-level signals and differential, bipolar RS-232 line signals. The MAX3243 belongs to the RS-232 interface hierarchy, combining line drivers, line receivers, charge-pump voltage conversion, and automatic power management in one package. It is used to connect UART, microcontroller, industrial-control, and data-processing systems to legacy serial ports through a ±15kV-protected communications interface.
Key features include a 3.0V to 5.5V operating supply, 250kbps maximum data rate, three RS-232 drivers, five RS-232 receivers, and low 1µA shutdown supply current. The ±15kV ESD protection improves robustness when cables are connected or disconnected near exposed equipment. AutoShutdown and AutoShutdown Plus operation reduce supply current when the connected system is inactive, while the always-active receiver allows monitoring even when the main supply has shut down.
The MAX3243E family uses an internal charge-pump circuit to generate the positive and negative voltages required by RS-232 transmitters. This architecture lets a 3.0V to 5.5V system communicate with conventional RS-232 equipment without a separate negative supply. The MAX3243EEUI+T is specified for a -40°C to +85°C temperature range and is packaged in a 28-pin TSSOP for surface-mount industrial and embedded equipment.
Typical applications include industrial serial consoles, instrumentation interfaces, point-of-sale equipment, telecom systems, embedded control modules, and peripheral connectivity. In each case, the transceiver provides the electrical conversion and signal protection needed between a low-voltage digital controller and an RS-232 port. Designers should verify the required baud rate, cable length, connector protection, supply sequencing, and charge-pump capacitor placement against the manufacturer’s recommended application circuit.
For a robust design, place the charge-pump and supply-bypass capacitors close to their associated pins, route the RS-232 driver outputs and receiver inputs away from sensitive digital signals, and provide appropriate chassis grounding at the connector. The integrated ±15kV ESD protection does not replace external surge and lightning protection for long or unprotected cables. This page also organizes package, replacement, and application guidance to support faster engineering selection.
直接替換替代品,適用於 MAX3243EEUI+T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX3243EEUI+T (相同外形與佔位) — 差異在於 Product Type, ESD Protection, Number of Receivers, Supply Voltage Range, Interface Standard.
MAX3243EIPWR
✅ 直接替換聯絡詢價
查看資料表 →ST3243EBTR
✅ 直接替換📋 參考替代品(不在目錄中)
MAX3243EEUI+T 規格
| Product Type | RS-232 transceiver |
| Supply Voltage Range | 3.0V to 5.5V |
| Maximum Data Rate | 250kbps |
| Driver Count | 3 drivers |
| Receiver Count | 5 receivers |
| Duplex Mode | Full duplex |
| ESD Protection | ±15kV |
| Shutdown Supply Current | 1µA |
| Power Management Feature | AutoShutdown |
| 工作溫度範圍 | -40°C to +85°C |
| 封裝 | 28-pin TSSOP |
| 安裝類型 | Surface mount |
| Supported Standards | EIA/TIA-232, V.28 and V.24 |
| RoHS 狀態 | RoHS compliant |
| Typical Application | UART-to-RS-232 interface |
MAX3243EEUI+T 28-pin tssop 腳位配置指南
MAX3243EEUI+T(28-pin tssop 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX3243EEUI+T.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX3243EEUI+T 適用於 6 應用s: Industrial Serial Console, Point-of-Sale Terminal, Instrumentation and Test Equipment, Embedded Data Acquisition Module, Telecom Network Equipment, Peripheral and Cable Connectivity.
Industrial Serial Console
The MAX3243EEUI+T fits an industrial serial console because its three drivers and five receivers support bidirectional RS-232 communication from a 3.0V to 5.5V embedded controller. The 250kbps maximum data rate provides ample margin for configuration, logging, and diagnostic traffic. Its -40°C to +85°C range is suitable for many industrial environments, while ±15kV ESD protection improves resilience during routine cable connection. The always-active receiver can also monitor a remote line while AutoShutdown reduces power. Designers should still add external surge protection when a console cable exits the enclosure or connects to unprotected industrial cabling.
推薦
Point-of-Sale Terminal
A point-of-sale terminal can use the MAX3243EEUI+T to bridge a low-voltage UART controller to an RS-232 peripheral such as a printer, scanner, or customer display. The 3.0V to 5.5V supply range supports both 3.3V and 5V logic systems, and three transmitter channels allow several serial accessories to share a multi-drop wiring arrangement when the system design permits it. The 250kbps capability is substantially faster than common peripheral baud rates. AutoShutdown helps control idle-system consumption, and the integrated ±15kV protection provides useful margin for cables handled by store personnel.
推薦
Instrumentation and Test Equipment
The MAX3243EEUI+T is appropriate for legacy test and measurement equipment that still uses an RS-232 command or measurement port. Its 3-driver/5-receiver organization supports a control channel plus multiple monitoring inputs, while the 250kbps rate supports command throughput and moderate data logging. The always-active receiver is valuable when an instrument must observe a signal even while the main transceiver has entered AutoShutdown. Because laboratory and industrial cables can carry large external transients, the integrated ±15kV ESD rating should be complemented by suitable connector protection and a defined chassis-ground strategy.
推薦
Embedded Data Acquisition Module
The MAX3243EEUI+T can connect an embedded acquisition module to legacy RS-232 sensors, programmers, or service equipment. The device accepts a 3.0V to 5.5V supply, allowing operation from common embedded rails, and its 250kbps data rate is suitable for many command-oriented acquisition protocols. Five receivers provide additional monitoring paths for status and interlock signals. AutoShutdown is valuable in battery- or power-constrained portable systems because the supply current can fall to approximately 1µA when no valid activity is detected. Firmware should account for wake-up latency and ensure that required monitoring receivers remain active where appropriate.
推薦
Telecom Network Equipment
The MAX3243EEUI+T is suitable for service and configuration interfaces within telecom equipment that retains RS-232 connectivity. Its three drivers and five receivers can support equipment-control and monitoring functions, while the 250kbps rate is adequate for administrative commands and low-bandwidth diagnostics. The -40°C to +85°C operating range covers many outdoor and indoor telecom installations. AutoShutdown helps control consumption when management ports are idle, and ±15kV ESD protection strengthens the interface against nearby charged cables. Equipment exposed to lightning or severe industrial transients still requires coordinated surge protection, bonding, and grounding.
推薦
Peripheral and Cable Connectivity
The MAX3243EEUI+T provides robust logic-to-RS-232 conversion for peripherals connected by short or medium-length shielded cables. Its 250kbps capability supports printers, scanners, programming equipment, and legacy control modules without requiring a separate negative supply. The ±15kV ESD protection is particularly useful for user-accessible connectors because it increases tolerance to electrostatic discharge during installation and servicing. Automatic shutdown reduces board-level standby demand, while the always-active receiver supports monitoring functions that must remain available. The PCB design should preserve the manufacturer’s charge-pump capacitor layout and keep transceiver routing away from sensitive analog or high-speed digital paths.
推薦
推薦產品摘要
工程參考資料,適用於 MAX3243EEUI+T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX3243EIPWR | ST3243EBTR |
|---|---|---|---|
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Brand | Analog Devices | Texas Instruments | STMicroelectronics |
| Transceiver Configuration | 3 drivers, 5 receivers | 3 drivers, 5 receivers | 3 drivers, 5 receivers |
主要差異化特點
- Higher channel count than a basic RS-232 interface (對比MAX232EIPWR)
- Always-active monitoring receiver (對比ST3243EBTR)
- Defined extended-temperature operating range (對比MAX3243EIPWR)
設計說明
Follow the MAX3243E recommended layout for the charge-pump capacitors and supply bypass components. Keep these components close to their associated device pins, use short return paths, and place the bypass capacitor where its ground connection joins the main ground plane. The exact capacitor values and PCB dimensions must be taken from the manufacturer application circuit because changing the charge-pump layout can affect startup, ringing, and transmitter output behavior.
Separate RS-232 driver outputs and receiver inputs from clocks, sensors, ADC signals, and other low-level analog paths. Driver edges can couple into nearby traces even though the interface uses a differential bipolar protocol at its external pins. Route the cable-side nets directly toward the connector or protection device, maintain the recommended spacing from unprotected board edges, and provide a low-impedance chassis-ground connection at the equipment entry point.
Do not treat the integrated ±15kV ESD rating as complete lightning or industrial surge protection. Long external cables can present transients beyond the interface’s ESD withstand rating, so use appropriately rated protection when the cable leaves the enclosure. Also confirm the connector shield and chassis-ground strategy because incorrectly routing surge current through the logic ground can damage surrounding equipment.
Account for AutoShutdown timing in the host firmware. The device can reduce shutdown supply current to approximately 1µA, but waking, charge-pump startup, and receiver qualification add latency before communication is reliable. Keep an always-active receiver path when the system must monitor a remote RS-232 line during low-power operation, and validate the complete wake-up sequence across temperature and supply-voltage corners.
合規資訊
The product listing identifies MAX3243EEUI+T as RoHS compliant. Reach, AEC-Q100, lead-free, halogen-free, and conflict-minerals status are not established by the cited product information and remain unknown.