NXP Semiconductors

MC33199DR2 - Automotive ISO 9141 Driver | NXP

Teilenummer: MC33199DR2 ✓ Aktiv
14-pin SOIC Package
MOQ: 1 |

MC33199DR2 Übersicht

NXP Semiconductors MC33199DR2 is an automotive ISO 9141 serial-link driver with one driver channel and no receiver channels, packaged in a 14-pin SOIC. It is designed for diagnostic systems in which a vehicle controller communicates with the K and L lines of an ISO diagnostic connector. The MC33199D family was developed for ISO 9141 diagnostic-interface requirements.

An ISO 9141 serial-link driver is an interface circuit that connects a microcontroller or other diagnostic controller to a vehicle network. It belongs to the broader hierarchy of automotive interface ICs, serial transceiver ICs, interface ICs, and semiconductors. Its practical role is to translate controller-level logic signals into electrical signaling suitable for the physical diagnostic bus while providing the electrical characteristics required by the ISO 9141 application.

The principal identified feature is the MC33199D's 1-driver/0-receiver arrangement. This focused architecture is appropriate when the surrounding diagnostic electronics perform receive functions elsewhere and the MCU requires a dedicated ISO 9141 line driver. Its 14-SOIC package provides a conventional surface-mount interface that can be assembled using standard automotive PCB practices. The DR2 ordering suffix identifies the manufacturer's specified packaging configuration.

The device is intended for automotive diagnostic communication rather than general-purpose RS-232, RS-485, or CAN signal conditioning. It should be selected when the system architecture requires an ISO 9141 K-line or L-line interface between a vehicle controller and an external diagnostic connector. Designers must still confirm voltage levels, bus topology, external network components, protection requirements, and timing against the relevant vehicle diagnostic standard before releasing the design.

Typical applications include automotive diagnostic connectors, engine-control test equipment, vehicle communication modules, garage-test equipment, and service-bus analyzers. These systems often combine an MCU, an ISO 9141 physical-layer driver, connector protection, and diagnostic software. MC33199DR2 is useful when the diagnostic interface is specifically based on ISO 9141 rather than a higher-bandwidth CAN or LIN network.

The principal design consideration is interface compatibility. Confirm that the selected MCU output levels, timing, and K-line or L-line wiring match the MC33199D requirements. Because an automotive diagnostic port connects to external equipment and vehicle wiring, validate transient immunity, fault behavior, grounding, and protection at the connector rather than treating the IC as the only safeguard.

This product page combines the exact MC33199DR2 ordering information, package identity, documented interface role, sourcing links, and engineering-oriented selection guidance. It also distinguishes verified drop-in candidates from merely similar interface ICs, helping engineers avoid choosing a functionally related transceiver that cannot replace the original footprint.

Drop-in-Alternativen für MC33199DR2 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit MC33199DR2 (gleiche Bauform und Footprint) – abweichend in Package, Product Type, Package Width, Application Category, Package Length.

NXP
Package: 14-SOIC
Product Type: Automotive ISO 9141 serial interface circuit
Package Length: 0.154 inch
Vergleichen mit MC33199DR2 →
NXP Semiconductors
Package: 8-SOIC
Product Type: Class B Serial Transceiver
Package Width: 0.154 inch (3.90 mm)
Vergleichen mit MC33199DR2 →

MC33199D

✅ Drop-In ⚠️ Spezifikationen ungeprüft
NXP
📦 14-SOIC
Automotive ISO 9141 serial interface circuit · ISO 9141 · 1 · 1 · Bidirectional K-line driver · L-line receiver for ISO 9141 wake-up sequence · 4.5 V to 5.5 V · 14-SOIC

Preis auf Anfrage

Datenblatt ansehen →

MC33390D

✅ Drop-In ⚠️ Spezifikationen ungeprüft
NXP Semiconductors
📦 14-SOIC
Class B Serial Transceiver · 1/1 · 1 driver and 1 receiver · 9 V to 16 V · 10.4 kbps · Bi-directional half-duplex · Single-wire bus · Automotive SAE Standard J1850 Class B Data Communication Network Interface

Preis auf Anfrage

Datenblatt ansehen →

MC33391D

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-SOIC
Automotive ISO 9141-interface alternative with related driver functions; output configuration and timing differences require verification

📋 Referenzalternative (nicht im Katalog)

MC33199DR2 Technische Daten

Product Type Automotive ISO 9141 serial-link driver IC
Driver Count 1 driver channel
Receiver Count 0 receiver channels
Diagnostic Standard ISO 9141
Application Category Automotive diagnostic interface
Gehäuse 14-pin SOIC
Package Width 3.90 mm
Package Length 0.154 in / 3.91 mm
Montageart Surface mount
Anzahl der Pins 14 pins

MC33199DR2 0.154 in / 3.91 mm Pinbelegungsleitfaden

Pinbelegung für MC33199DR2 (0.154 in / 3.91 mm-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für MC33199DR2 im 0.154 in / 3.91 mm-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MC33199DR2.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MC33199DR2 ist geeignet für 6 Anwendungs: Vehicle Diagnostic Interfaces, Automotive ECU Test Equipment, Engine Control Modules, Garage Diagnostic Analyzers, Automotive Communication Modules, Production-Line Vehicle Diagnostics.

🚗

Vehicle Diagnostic Interfaces

The MC33199DR2 fits an ISO 9141 diagnostic path between a vehicle controller and the external diagnostic connector because the MC33199D family provides one dedicated ISO 9141 driver channel. Place the device on the controller side of the K-line or L-line network and connect its logic input to the appropriate vehicle-controller output. Its 14-SOIC package supports conventional surface-mount assembly, while the confirmed one-driver architecture requires the receive function to be handled elsewhere when needed.

🏭

Automotive ECU Test Equipment

MC33199DR2 can serve as the ISO 9141 physical-layer driver in test equipment that emulates or monitors a vehicle diagnostic port. The one-driver/0-receiver arrangement is appropriate when the tester needs to inject a request signal but obtains diagnostic information through another receiver channel or circuit. Designers should reproduce the required line-network components and connector protection, then validate signal timing against the ISO 9141 implementation used by the vehicle platform.

⚙️

Engine Control Modules

The MC33199DR2 is applicable when an engine-control module must expose an ISO 9141 diagnostic connection for service tools or production testing. Its confirmed 14-SOIC package and single-driver architecture support a compact diagnostic subsystem around an automotive microcontroller. Keep the bus-side trace away from sensitive analog and processor supplies, provide the specified protection near the connector, and verify the network's idle, active, and faulted states across temperature.

🔧

Garage Diagnostic Analyzers

A portable garage diagnostic analyzer can use MC33199DR2 as the ISO 9141 driver on its vehicle-facing interface. The device is specifically described as an interface between a microcontroller and the K and L lines of an ISO diagnostic port, making it appropriate for systems that communicate through legacy ISO 9141 diagnostic links. The analyzer should add automotive-grade transient protection and verify ground offsets, bus loading, and connector behavior with the service equipment expected in workshop conditions.

🌐

Automotive Communication Modules

MC33199DR2 can be integrated into a communication module that provides an ISO 9141 diagnostic channel alongside other vehicle functions. The 14-SOIC package is easy to place beside an automotive microcontroller, and the dedicated driver function provides a defined interface toward the diagnostic wiring. Because the device has no integrated receiver channel, a complete bidirectional diagnostic design may require a separate receiver arrangement or a related multi-function interface device.

🏭

Production-Line Vehicle Diagnostics

MC33199DR2 is suitable for production-line systems that issue ISO 9141 diagnostic commands during end-of-line testing. A one-driver architecture is useful when the tester transmits requests through the vehicle diagnostic line while a separate circuit handles reception or response detection. Validate signal timing, voltage margins, and fault recovery at the connected harness before using the setup in high-volume production, and place connector protection close to the point where the external cable enters the equipment.

Zusammenfassung der empfohlenen Produkte

What is the MC33199DR2?
The MC33199DR2 is a 1-driver/0-receiver automotive ISO 9141 serial-link driver in a 14-pin SOIC package. According to the manufacturer datasheet, the MC33199D is an interface between a microcontroller and the K and L lines of an ISO diagnostic port. It is intended for diagnostic systems rather than general-purpose CAN, LIN, RS-232, or RS-485 communication.
What is the operating voltage of MC33199DR2?
The operating voltage cannot be stated reliably without the MC33199D electrical-characteristics table. The confirmed device identity is a 14-SOIC, 1-driver/0-receiver ISO 9141 automotive interface. Before connecting a supply rail, consult the manufacturer datasheet for the recommended operating range, absolute maximum ratings, ground reference, and load-current limits, and use the device only within those limits.
Where can I download the MC33199DR2 datasheet PDF?
The MC33199DR2 datasheet is available through the NXP MC33199 document link on this page and through the listed document-index and distributor pages. The manufacturer document is titled “MC33199 Automotive ISO 9141 Serial Link Driver.” Use the manufacturer PDF for final electrical limits, timing, pin descriptions, application information, and ordering-table verification before completing a production design.
Where can I find the MC33199DR2 pinout?
The MC33199DR2 pin assignments must be taken from the pin-description table in the manufacturer MC33199 datasheet because the complete 14-pin map is not reproduced here. The confirmed package is 14-pin SOIC, with 14 leads in the standard 3.90 mm narrow body. Assign every net from the datasheet table, including supply, ground, logic input, bus-side connection, and any no-connect or test assignments.
Can MC33199DR2 be used with an automotive diagnostic connector?
Yes, MC33199DR2 is intended for an ISO 9141 diagnostic interface between a controller and the K and L lines of a vehicle diagnostic port. Its documented role and 1-driver/0-receiver configuration suit a dedicated ISO 9141 physical-layer path. The complete external circuit must still include the required connector, protection, biasing, and network components specified for the vehicle platform.
MC33199DR2 vs MC33199D - which one should I select?
MC33199DR2 is the 14-SOIC ordering configuration of the MC33199D automotive ISO 9141 driver. MC33199D is the base device designation, while DR2 identifies the specific ordering and packaging variant. For a board designed around the 14-SOIC MC33199DR2, use the exact ordering code in the BOM and verify that the manufacturer's ordering table associates that code with the intended package and qualification level.
What is the best drop-in replacement for MC33199DR2?
The MC33199D is the closest same-family replacement candidate because it denotes the base automotive ISO 9141 serial-link driver associated with MC33199DR2. However, a genuine drop-in decision requires matching the 14-SOIC footprint, lead functions, electrical ratings, timing, temperature grade, and automotive qualification. Other interface ICs with similar protocol or package descriptions should not be assumed to be pin-to-pin replacements.
Can MC33390D replace MC33199DR2?
MC33390D may be considered only after its manufacturer documentation confirms identical lead functions and electrical behavior at the required diagnostic operating point. Both devices are associated with automotive ISO 9141 interface applications, but protocol similarity alone does not establish drop-in compatibility. Verify package dimensions, exposed connections, supply limits, bus-side drive behavior, timing, and qualification before substituting it into an existing MC33199DR2 PCB.
When should I choose MC33199DR2 instead of a CAN transceiver?
Choose MC33199DR2 when the required vehicle diagnostic physical layer is specifically ISO 9141 and the design needs a dedicated K-line or L-line driver. Choose a CAN transceiver only when the vehicle platform, diagnostic tool, and network architecture use CAN framing and bus electrical requirements. MC33199DR2 has one driver and no receiver, so it is not a general CAN or bidirectional serial transceiver.
Is MC33199DR2 suitable for K-line and L-line diagnostic interfaces?
MC33199DR2 is suitable for ISO 9141 diagnostic-interface roles involving the vehicle K and L lines. The confirmed device function is an automotive ISO 9141 serial-link driver with one driver channel and no receiver channel. Final suitability depends on matching the selected line, logic levels, timing, protection, and network topology to the manufacturer's application requirements.
How much current can MC33199DR2 drive?
The exact output-current capability should be taken from the MC33199D electrical-characteristics table because no numeric drive-current limit is established on this page. The confirmed function is a one-channel automotive ISO 9141 driver. Account for the diagnostic-port load, wiring length, termination and bias components, connector leakage, and any transient conditions rather than selecting a network solely from nominal bus current.
What design considerations matter for an MC33199DR2 diagnostic circuit?
The critical design work is interface matching, fault protection, and signal integrity. According to the manufacturer datasheet, MC33199D is intended to connect a microcontroller with the K and L lines of an ISO diagnostic port. Place protection close to the connector, maintain the required network components, provide a clean ground reference, and verify timing and bus levels with the external diagnostic equipment used in the intended test environment.
Where can I buy MC33199DR2 and check its lead time?
Use the “Request a Quote” form on this page to request MC33199DR2 pricing, current availability, minimum order quantity, and lead time. The form allows a buyer to request the exact 14-SOIC ordering code without substituting another package variant. Confirm the returned quotation and manufacturing status before releasing the component into a scheduled production build.
Is MC33199DR2 currently in stock?
Current stock should be confirmed through the “Request a Quote” form on this page. Stock status can vary by package suffix, manufacturing location, and order quantity, while the distributor search data confirms that MC33199DR2 is cataloged as a 14-SOIC NXP interface IC. Request quantity, target date, and approved-source requirements along with the stock inquiry.
What are the key specifications engineers should know about MC33199DR2?
MC33199DR2 is a 14-pin SOIC automotive interface IC implementing one ISO 9141 driver channel and no receiver channels. Its primary purpose is to connect a microcontroller with the K and L lines of an ISO diagnostic port. The package is a 3.90 mm-wide surface-mount SOIC. Supply limits, timing, current, temperature range, and automotive qualification should be confirmed from the manufacturer datasheet before design release.

Technische Referenzdaten für MC33199DR2 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose MC33199DR2 when the product must implement an ISO 9141 diagnostic connection and the PCB already expects the exact NXP 14-SOIC ordering configuration. Its confirmed 1-driver/0-receiver architecture is particularly suitable when reception is implemented elsewhere and the vehicle controller only needs a dedicated K-line or L-line drive function. MC33199D is the closest base-family option when the ordering-table and qualification details match the intended assembly. Consider MC33390D or MC33391D only after comparing their complete pin functions, timing, drive capability, and fault behavior against MC33199DR2; a shared 14-SOIC outline alone does not establish drop-in compatibility. For CAN, LIN, high-speed automotive Ethernet, or generic RS-485 links, select the corresponding transceiver rather than an ISO 9141 driver.

Vergleich mit Alternativen

Parameter Dieses Produkt MC33199D MC33390D MC33391D
Package 14-SOIC 14-SOIC 14-SOIC 14-SOIC
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Primary Function Automotive ISO 9141 serial-link driver Automotive ISO 9141 serial-link driver Automotive ISO 9141 interface device Automotive ISO 9141 interface device
Diagnostic Standard ISO 9141 ISO 9141 ISO 9141 ISO 9141
Number of Pins 14 pins 14 pins 14 pins 14 pins
Automotive Interface Role MCU-to-K/L-line diagnostic interface MCU-to-K/L-line diagnostic interface Automotive diagnostic bus interface Automotive diagnostic bus interface

Wichtigste Unterscheidungsmerkmale

  • Exact base-family ordering relationship (vs. MC33199D)
  • Focused driver-only signal path (vs. MC33390D)
  • Purpose-defined K/L-line interface role (vs. MC33391D)

Designhinweise

Do not treat an ISO 9141-compatible interface IC as a universal replacement for CAN, LIN, RS-232, or RS-485 hardware. MC33199DR2 has a confirmed 1-driver/0-receiver arrangement, so a design requiring an integrated receiver may need additional circuitry. Before substituting a related 14-pin device, compare every lead function, bus-side connection, supply limit, timing characteristic, and fault state against the original MC33199D schematic.

Route the bus-side K-line or L-line connection away from clocks, sensors, radio-frequency circuits, and other sensitive analog inputs. Keep the connector protection network close to the diagnostic connector so transient current is diverted before it reaches the IC. Provide a low-impedance ground reference near the device and keep the protected diagnostic connection physically separated from unrelated external wiring.

Use the manufacturer's recommended supply arrangement and verify power-up, power-down, idle, and fault behavior on the complete diagnostic circuit. The available product information does not establish the numeric supply range or output-current limit for MC33199DR2, so do not estimate those values from an unrelated interface IC. Confirm them in the MC33199D electrical characteristics and worst-case harness-loading conditions.

Validate the complete vehicle-side network rather than only the IC output waveform. Include cable length, connector capacitance, external bias components, harness leakage, and the receiving equipment in the test. MC33199DR2 is a one-channel ISO 9141 driver, and timing or voltage margins may differ when connected to real diagnostic equipment even if the isolated bench waveform appears correct.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The device is described as an automotive ISO 9141 serial-link driver, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is available for this ordering code.

Daten verifiziert am: 2026-11-16 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MC33199DR2 datasheet MC33199DR2 pinout MC33199DR2 datasheet pdf MC33199DR2 ISO 9141 driver MC33199DR2 14-SOIC NXP MC33199DR2 MC33199DR2 replacement MC33199DR2 equivalent MC33199DR2 vs MC33390D MC33199DR2 price MC33199DR2 stock MC33199 automotive diagnostic interface

Verwandte Bauteile & Begriffe

NXP Semiconductors MC33199DR2 MC33199D MC33390D MC33391D ISO 9141 automotive diagnostic interface serial-link driver interface IC automotive transceiver IC semiconductor K line L line microcontroller vehicle diagnostic connector 14-SOIC SOIC family surface-mount package SMD automotive electronics engine control module RoHS REACH AEC-Q100
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen