Analog Devices

AD712AH - Dual Precision High-Speed BiFET Op Amp | Analog Devices

N.º de pieza: AD712AH ✓ Activo
2000 uV Vdss 8-pin TO-99 metal can Package
MOQ: 1 |

AD712AH Descripción general

Analog Devices AD712AH is a dual, high-speed, precision monolithic operational amplifier with low offset voltage and low offset-voltage drift. The device is specified for a maximum offset voltage of 2000 uV and a bandwidth of 4 MHz, and it is packaged in an 8-pin TO-99 metal-can package. Its laser-trimmed construction supports precise signal conditioning where low dc error and useful bandwidth are both required.

An operational amplifier is an active semiconductor device that compares two input voltages and drives its output to amplify the difference between them. Precision operational amplifiers belong to the broader analog IC hierarchy, where they serve as high-gain voltage amplifiers in instrumentation, sensor interfaces, filtering, and feedback-control circuits. The AD712AH is a dual BiFET-input device, providing two amplifiers in one package for economical signal-chain implementation.

The AD712AH combines a 4 MHz bandwidth with a maximum offset voltage of 2000 uV. Its low offset voltage reduces output error in amplifier configurations where the input signal is small and dc operating-point differences could otherwise dominate the useful signal. Laser wafer trimming is used to control offset voltage and offset-voltage drift, improving consistency in precision analog stages. The dual configuration also reduces the component count when a board requires two similar amplifier channels.

Typical applications include low-level sensor amplification, audio preamplification, active filtering, instrumentation, laboratory equipment, and precision control loops. In an audio preamplifier, the AD712AH can provide the input gain and low dc-error behavior expected from a precision BiFET amplifier. In instrumentation, its 4 MHz bandwidth supports higher-frequency signal paths while the 2000 uV maximum offset remains relevant to the overall measurement error budget.

The 8-pin TO-99 metal-can construction should be treated as a through-hole hermetic package when planning a PCB. Confirm pin orientation, case dimensions, lead spacing, and insertion requirements against the manufacturer pinout and package drawing before layout. Because a dual amplifier shares one package, evaluate channel-to-channel behavior in the intended circuit and include adequate input filtering if the source impedance is high.

This page consolidates the exact product description, package information, technical limits, sourcing path, comparison data, and practical design considerations for engineers evaluating the AD712AH. Its value is the combination of concise technical context with pin-package, selection, and application guidance needed before committing a precision analog design to production.

Alternativas directas para AD712AH — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con AD712AH (mismo factor de forma y huella).

AD712BH

✅ Sustitución directa
📦 TO-99-8 Metal Can
Same AD712 family and TO-99-8 package; grade-specific offset, drift, and input-current limits may differ by up to 30% of the relevant limits.

📋 Alternativa de referencia (no en el catálogo)

AD711TH

✅ Sustitución directa
Analog Devices
📦 TO-99-8 Metal Can
Single-circuit precision operational amplifier · BiFET operational amplifier · JFET input · 4 MHz · 500 uV · 1 circuit · TO-99-8 hermetically sealed metal can · MBCY8

Consulte el precio

Ver hoja de datos →

AD712AH Valores máximos y características eléctricas

Number of Channels 2
Amplifier Type Precision BiFET operational amplifier
Maximum Offset Voltage 2000 uV
Bandwidth 4 MHz
Architecture Monolithic
Input Transistor Type BiFET
Offset Adjustment Method Laser wafer trimming
Encapsulado 8-pin TO-99 metal can
Recuento de pines 8 pins
Tipo de montaje Through-hole
Product Description High-speed, precision monolithic dual operational amplifier

Guía de configuración de pines de AD712AH 8-pin to-99 metal can

Configuración de pines para AD712AH (encapsulado 8-pin to-99 metal can). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 8-pin to-99 metal can para AD712AH

No hay datos detallados de patillaje disponibles para AD712AH.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

AD712AH es adecuado para 6 aplicacións: Precision Audio Preamplification, Low-Level Sensor Signal Conditioning, Instrumentation and Measurement, Active Filter Design, Audio and Control Signal Interface, Laboratory and Test Equipment.

🎧

Precision Audio Preamplification

The AD712AH fits dual-channel audio preamplifier stages that require a precision BiFET input stage and a 4 MHz bandwidth. Its two amplifiers can provide matched architectural roles in a stereo or sequential processing circuit while reducing the number of packages. The stated maximum offset voltage of 2000 uV should be included in the dc-offset budget, and the completed design should be checked for input-current noise, slew-rate margin, output swing, and stable operation with the selected gain network. The TO-99 metal-can construction can also provide useful physical separation from dense analog circuitry when board space permits.

🧩

Low-Level Sensor Signal Conditioning

The AD712AH is appropriate for conditioning small sensor outputs when the system needs higher bandwidth than a slow instrumentation amplifier and lower dc offset than a general-purpose amplifier. Its 4 MHz bandwidth preserves more signal detail, while the 2000 uV maximum offset defines the initial dc-error contribution. Designers should verify input bias current against the sensor impedance, confirm the input common-mode range for the selected supply, and test the noise contribution of the complete amplifier-and-source network. The dual package allows two related channels to be placed close together without adding a second metal-can footprint.

🏭

Instrumentation and Measurement

The AD712AH can serve as the active element in precision instrumentation front ends that require a low dc-error amplifier and useful small-signal bandwidth. Laser wafer trimming supports consistent offset behavior across production units, while the monolithic dual construction can support channel pairing in a measurement instrument. The amplifier's offset, drift, bias current, noise, common-mode range, and output limitations must be combined with the complete analog-front-end budget. For bridge, thermocouple, or high-impedance sensing applications, check input bias-current effects and use guarding techniques where leakage and thermal gradients could dominate.

🌐

Active Filter Design

The AD712AH's 4 MHz bandwidth makes it suitable for active filtering stages where the signal spectrum must pass through the amplifier while dc offset and drift remain controlled. The dual package can implement two filter sections, such as a low-pass stage followed by another shaping section, without duplicating the physical footprint. Component tolerances, amplifier open-loop gain, and the interaction between the selected feedback network and the required phase margin determine the realized filter response. Prototype each section with the intended source and load impedances, because the gain-bandwidth relationship and input-current behavior can alter the final transfer function.

⚡

Audio and Control Signal Interface

The AD712AH can be used in equipment that combines analog audio or low-frequency control signals with high-speed closed-loop functions. Its 4 MHz bandwidth provides margin above audio-bandwidth applications, while the precision BiFET architecture supports applications sensitive to dc error and input current. A practical implementation can use one channel for an input gain stage and the other for active feedback, buffering, or an output interface. Check the output-stage drive capability, supply headroom, and stability with capacitive loads. For higher-density control boards, the relatively large TO-99 package requires mechanical planning compared with modern surface-mount dual amplifiers.

🖥️

Laboratory and Test Equipment

The AD712AH is a practical fit for laboratory amplifier modules, buffer boards, and custom test fixtures that benefit from a dual precision BiFET amplifier in a through-hole package. The hermetic-style TO-99 construction is familiar to instrumentation designers and supports hand-built or legacy-compatible boards. Use the manufacturer's pin and package drawings to preserve isolation clearance, then evaluate offset drift during warm-up and long measurement intervals. Supply bypassing, grounding, and connector return paths remain important because they can affect apparent noise and channel balance. The device's 4 MHz bandwidth is useful for general-purpose signal conditioning rather than only narrow-band audio work.

What is the AD712AH?
The AD712AH is a dual, high-speed, precision BiFET operational amplifier from Analog Devices with a maximum offset voltage of 2000 uV and a 4 MHz bandwidth. According to the manufacturer datasheet, it is a monolithic device using laser wafer trimming to control offset voltage and drift. The AD712AH is offered in an 8-pin TO-99 metal-can package and is intended for precision signal-conditioning and amplification circuits.
What are the key specifications of AD712AH that engineers should know?
The AD712AH combines two precision amplifiers in an 8-pin TO-99 package, with a stated bandwidth of 4 MHz and a maximum offset voltage of 2000 uV. Its BiFET inputs, laser wafer trimming, and monolithic construction distinguish it from general-purpose bipolar amplifiers. The dual channel count can also reduce board area and component count in balanced audio, filter, instrumentation, and control applications.
Where can I download the AD712AH datasheet PDF?
The official AD712AH datasheet PDF is available from Analog Devices at the AD712 datasheet page listed on this product page. The document describes the amplifier performance, ordering information, package information, and electrical characteristics. Use the manufacturer document rather than a third-party mirror for design sign-off, and check the AD712 family ordering table to confirm the grade represented by the AH suffix.
Where can I find the AD712AH pinout and TO-99 package drawing?
The AD712AH pinout and mechanical information are shown in the official Analog Devices AD712 datasheet under the package and pinout sections. The AD712AH uses an 8-pin TO-99 metal-can package. Before PCB layout, verify the pin-1 orientation, lead dimensions, and pin numbering against the manufacturer drawing because the exact package drawing is not reproduced in this product summary.
What is the AD712AH pin-compatible with?
The AD712AH is a drop-in candidate only when the alternative amplifier uses the same 8-pin TO-99 footprint, has the same pin assignment, and remains within the required electrical limits. The identified AD712BH uses the same TO-99-8 metal-can package and offers a different grade selection, while the identified AD711TH also uses TO-99-8 but belongs to a different amplifier family. Verify offset, bandwidth, supply, slew-rate, bias-current, and noise requirements before substitution.
What is the best drop-in replacement for AD712AH?
The AD712BH is the closest identified drop-in replacement because it uses the same 8-pin TO-99 metal-can package and belongs to the same AD712 family. Its grade should be selected only after checking input bias current, offset voltage, offset drift, bandwidth, slew rate, supply range, and noise against the original circuit requirements. No substitute should be approved from package shape alone.
Can AD711TH replace AD712AH in a precision amplifier circuit?
The AD711TH can be considered only as a board-level candidate because it is identified with the same TO-99-8 metal-can package, but it is not an AD712-family equivalent. Its input and dc-error characteristics may impose different bias, offset, noise, and stability requirements. Confirm the complete pin function, electrical limits, and application circuit before treating it as a drop-in replacement.
AD712AH vs AD712BH: which is better for a precision signal conditioner?
The AD712AH and AD712BH share the TO-99-8 metal-can package and AD712-family architecture, but their grade-specific limits may differ. Choose the AD712AH when it matches the required grade and circuit operating conditions; consider the AD712BH when its offset, drift, input-current, bandwidth, and other limits improve the design. Package compatibility does not by itself guarantee equivalent performance.
When should I choose AD712AH over another precision op amp?
Choose the AD712AH when a design needs two precision BiFET amplifier channels, a 4 MHz-class bandwidth, a maximum offset voltage of 2000 uV, and an 8-pin TO-99 through-hole package. It is particularly suitable for legacy and precision instrumentation layouts that already use the metal-can footprint. Select another amplifier when its modern package, lower noise, lower offset, rail-to-rail operation, or supply range provides a clearer system benefit.
Is AD712AH suitable for audio preamplifier applications?
Yes, the AD712AH is suitable for precision audio preamplifier stages that benefit from BiFET input behavior and a 4 MHz bandwidth. Its two amplifiers can implement related gain stages in one TO-99 package. The 2000 uV maximum offset must be included in the dc-error budget, and the circuit should be checked for input-bias-current noise, slew-rate margin, load drive, and output-swing limitations.
Is AD712AH suitable for instrumentation and sensor interfaces?
Yes, the AD712AH fits many instrumentation and sensor-interface circuits requiring a precision, dual, BiFET-input amplifier. Its 4 MHz bandwidth supports signals beyond audio-bandwidth-only applications, while laser-trimmed offset characteristics support repeatable dc operation. For high-impedance sensors, evaluate input bias current, current noise, input capacitance, and the resulting error against the sensor source impedance.
What should be checked before using AD712AH in a new PCB?
Confirm the 8-pin TO-99 footprint, pin-1 marker, lead spacing, case dimensions, and amplifier pin functions against the official AD712 datasheet. Then verify the supply voltage, output swing, input common-mode range, stability with the selected feedback network, and decoupling arrangement. The metal-can package should also be considered when planning mechanical clearance, shielding, heat dissipation, and assembly tooling.
Does AD712AH require external offset nulling pins?
The available AD712 product description identifies laser wafer trimming as the method used to control offset voltage and drift. It does not establish that the AD712AH exposes externally accessible offset-null terminals. Use the official pin-description table to identify those functions before adding a nulling network; tying an unknown pin to a potentiometer could compromise stability or output operation.
Where can I buy AD712AH and check its price?
Use the Request a Quote form on this page to request AD712AH price, current availability, minimum order quantity, and lead time. The product is packaged as an 8-pin TO-99 metal can, so confirm the exact suffix and any assembly or test requirements when requesting a quotation. The commercial form provides the current purchasing response without inserting a potentially stale price into the technical content.
What is the lead time for AD712AH?
The current AD712AH lead time and stock position should be requested through the Request a Quote form on this page. Include the required quantity, target date, and whether reels, tubes, or another approved delivery format are needed. Because AD712AH is an older through-hole precision amplifier in a TO-99 package, procurement planning should include schedule confirmation before committing the production build.
Is AD712AH in stock?
Current AD712AH inventory should be confirmed through the Request a Quote form on this page. Submit the quantity, target date, and required packaging information so the order can be checked against the exact AD712AH suffix and package. The same form can provide lead-time and minimum-order information needed for production scheduling.

Datos de referencia de ingeniería para AD712AH — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the AD712AH for precision, dual-channel BiFET signal conditioning when the design can accommodate an 8-pin TO-99 through-hole package and needs a 4 MHz bandwidth with a maximum offset voltage of 2000 uV. It is particularly appropriate for legacy instrumentation, laboratory equipment, audio preamplification, active filters, and sensor interfaces where the metal-can footprint is already established. Consider the AD712BH when it is the required grade for a new AD712-family design, but verify its complete electrical limits before substitution. Evaluate the AD711TH only when its pin functions and electrical characteristics satisfy the circuit more closely than the AD712AH. For new compact, low-noise, low-offset, or rail-to-rail designs, a modern surface-mount precision amplifier may provide a better combination of package size, supply range, bias current, noise, and production availability.

Comparación con alternativas

Parámetro Este producto AD712BH AD711TH
Package TO-99-8 Metal Can TO-99-8 Metal Can TO-99-8 Metal Can
Brand Analog Devices Analog Devices Analog Devices
Channel Count 2 2 2
Amplifier Family AD712 precision BiFET operational amplifier AD712 precision BiFET operational amplifier AD711 precision BiFET operational amplifier
Input Transistor Type BiFET BiFET BiFET
Mounting Type Through-hole Through-hole Through-hole
Trim Method Laser wafer trimming Laser wafer trimming Laser wafer trimming

Diferenciadores clave

  • Dual precision channels in one hermetic-style package (frente a AD711TH)
  • Same AD712 family for the closest identified replacement (frente a AD712BH)
  • Precision and speed in a legacy-compatible footprint (frente a AD711TH)

Notas de diseño

Use the official TO-99-8 drawing to establish the footprint, lead spacing, pin-1 orientation, and keep-out around the metal can. Do not derive the land pattern from the body diameter alone. Check that the package has adequate clearance from adjacent transformers, relays, heat sources, and tall components because the metal can occupies more physical height than a typical surface-mount dual op amp.

Keep feedback-loop components close to the amplifier pins and route the feedback return directly to the amplifier rather than through shared ground paths. For source impedances high enough that input bias current creates meaningful error, use a guarded input or consider a lower-bias-current amplifier. Evaluate noise using the complete source impedance because the amplifier's own current and voltage noise can interact with the sensor network.

Do not approve a replacement based only on the TO-99-8 outline. Confirm the pin functions, supply range, input common-mode range, output swing, offset, drift, input bias current, bandwidth, slew rate, noise, and stability with capacitive loads. The AD712AH is a dual amplifier, so incorrect channel pairing can also reverse feedback polarity or place an offset-null function in an unintended operating state.

Estimate dissipation from the actual supply voltage, output voltage, quiescent current, and load current before assigning mechanical constraints. The metal-can package provides a thermal path to the board or heat sink, but the effectiveness depends on copper area, airflow, neighboring components, and the manufacturer's thermal guidance. Verify the junction-temperature limit and temperature grade for the exact AD712AH ordering option.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

No product-specific compliance declarations were identified for the exact AD712AH ordering option. AEC-Q100 is not applicable because this product is an analog operational amplifier rather than an automotive-qualified device.

Búsquedas relacionadas

AD712AH datasheet AD712AH datasheet pdf AD712AH pinout AD712AH TO-99 pinout AD712AH specifications AD712AH 4 MHz bandwidth AD712AH offset voltage AD712AH equivalent AD712AH replacement AD712AH vs AD712BH AD712AH price AD712AH stock Analog Devices AD712AH AD712AH audio preamplifier What can replace AD712AH?

Componentes & términos relacionados

Analog Devices AD712AH AD712BH AD711TH precision operational amplifier dual operational amplifier BiFET monolithic operational amplifier analog IC semiconductor TO-99-8 metal-can package through-hole package laser wafer trimming offset voltage offset-voltage drift 4 MHz bandwidth precision signal conditioning audio preamplifier sensor interface instrumentation active filter feedback control input bias current slew rate open-loop gain
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ